prophet stuck at RGB screen - does nothing but RGB - JAMin, XDA Neo, S200 General

hi, i was upgrading last nite and i really don't know what i did and what happened, my prophet is stuck at RGB, it does not do anything else, can't even load windows nor connect to active sync. is it bricked? please help

What are the IPL and SPL?
Read this: http://wiki.xda-developers.com/index.php?pagename=Prophet_recovery

i have a G3
IPL: 2.20
SPL: 2.20
edit: i tried that guide but it does bot connect to active sync

Before or after the RUU?
If it's before, it shouldn't matter...

before, and i did not RUU, because it can't connect to phone

In the bottom left hand corner of the screen, some text should say "USB" if it does, your good to flash a ROM.

yes it does say USB, which ROM should i flash? wm5 or wm6? or should i RUU?

Flash the WM5 ROM linked to in the wiki page.

ok thnx i am currently flashing that ROM now and will tell you the results

thanks i successfully flashed the ROM. can you now please tell me how can i flash wm6 ROM?

Read the "NEW WM6 upgrade guide" that is a sticky at the top of the Prophet Mobile Six forum.

i'm stuck at this step where it says
go to the ExtRom folder. (Look at the picture) you will find ExtRom folder in most of the wm6 roms. when you download a wm6 rom, this folder is usually beside the Upgrade_ROM.bat .
please help what to do

If you have a new (almost all WM6.1 ROMs) ROM, it should be a single file. It should be "nk.nbf" if this is the case, you do not need to prepare the file.
You will need to HardSPL your device and then flash the ROM.

ok i did it. thank you very much

Related

help with my imate kjam

hi,
im a noob to this forum and pocket pcs and i think im doing something wrong but when i try to install mfrazzz's xda mobile 6 release 5 final. i its still the same old windows mobile 5
i think my cid is unlocked i followed the instructions given by farias thread.
how would i know if the cid is unlocked? i tried using mestrini's WST tool but i get an error.
thanks in advance
thanks for the help
7331ymerej said:
hi,
im a noob to this forum and pocket pcs and i think im doing something wrong but when i try to install mfrazzz's xda mobile 6 release 5 final. i its still the same old windows mobile 5
i think my cid is unlocked i followed the instructions given by farias thread.
how would i know if the cid is unlocked? i tried using mestrini's WST tool but i get an error.
thanks in advance
Click to expand...
Click to collapse
Always post vital data of the phone,untill it's not known which device you have,G3 or G4,it's hard to provide with any help.Post IPL SPL of your device.
If it's a G3 then its CID locked,you have not followed the correct unlocking procedure.Read the Guide and sticky by Dr.Puttingham and follow it correctly to CID unlock the phone.
If it's a G4,then you cannot straight away flash any Rom to it,to upgrade follow the method as Sticky 'SoftSPL or HardSPL' by equinox in G4 forum.
What error it gives while usung WST 4.2 Tool ?
Cheers !
i have a g3, and the ipl: 1.01 (becuase i downgraded because the instructions told me to) SPL : 2.16
and the wst tool give me a "in the rexx script named : at line number :2840"
and is there a way i can change me ipl back to 2.16? cause nothing is working for me =/
thank you for your response
7331ymerej said:
i have a g3, and the ipl: 1.01 (becuase i downgraded because the instructions told me to) SPL : 2.16
and the wst tool give me a "in the rexx script named : at line number :2840"
and is there a way i can change me ipl back to 2.16? cause nothing is working for me =/
thank you for your response
Click to expand...
Click to collapse
ok, you got ipl 1.01 cuz you downgraded with Button's Rom 1.05 but your spl remained unchanged 2.16,its nothing to worry about,it sometimes take a little more tries to downgrade spl to 1.01,flash the Button's Rom 1.05 a couple of more times to make both ipl/spl 1.xx,only then you can CID unlock the phone with lokiwiz 02b.Follow the guide for downgrading and unlocking at the below link and do the method correct.Your phone is still CID locked,untill you get your phone CID unlocked you can not upgrade to any wm6 Rom.
http://forum.xda-developers.com/showthread.php?t=285435
But if you want to go back to your original wm5 Official k-jam Rom and have ipl/spl 2.16,then Download official k-jam Rom 'K-JAM_WWE_216901_2169101_020710_ship.zip' from official website of i-mate k-jam or from the following link below:-
ftp://ftp.clubimate.com
1.unzip the Rom zipfile,get your phone into bootloaders screen (multicolored screen)by pressing and holding down the camera button and the Power ON button together,the phone will start in bootloaders(multicolored screen) it'll show you ipl 1.01/spl 2.16
2.when in bootloaders,connect your phone with pc via usb cable, a small usb written will appear at the bottom of the multicolored screen of your phone.confirm it.
3.open the unzipped folder of the downloaded Rom,run the RUU icon in it(double click Ruu.exe)
4. follow the instructions and flash the Rom,after completion,your phone will restart and start working.
Good luck !
thank you sooo soo much, im gonna try it again right now
i guess my phones SPL will not change. i must of flashed the ROM with buttons 1.05 about10 times but it still wont change .... oh well im just gonna go back to the stock rom my kjam is WEIRD haha
Please Help
Hello
I have the Kjam G3 (with IPL & SPL 2.16) & wm5. I want to upgrade to wm6.1 but the CID is locked. I tried the WST tools and followed the instructions to unlock the CID but nothing happened.
Please can any body help me to solve my problem and tell me any other way to unlock and where to download the wm6.1.
THANK YOU
READ the FAQs, they hold all of the answers that you need.

Thanks POF:How i Upgraded my DOPOD C800 with WM6

HI,
Thanks for POF and other forum members.
I upgraded my DOPOD C800 with WM6. Used POF HARD-SPL and Official HTC P4350 ROM.
Thanks
Jose
Can you mention the ipl and spl of your c800 before you had gone about with Hard-spl?
murali509 said:
Can you mention the ipl and spl of your c800 before you had gone about with Hard-spl?
Click to expand...
Click to collapse
Hi mine is- before upgrade
SPL 1.09.0001
IPL 1.09.0001
ROM 1.7.707.3 WWE
ROM Date 11/01/06
Radio 2.69.90
protocol 4.1.13.30
Ext rom 1.7.707.106
OS 1.7.0.0
I also have a Dopod C800 with the same ipl & spl. Can you direct me to the POF Hard-Spl files that you used? I have the HTC P4350 WWE WM6 RUU. Any help is greatly appreciated...scared to death I'll brick the phone!
How i upgraded My DOPOD C800
STEP I:
Download the following files
1) USPL --- Flah centre.rar file from
http://www.mediafire.com/?axtm5qlmbli
2) Official RUU -HTC_P4350_WWE_4.17.405.2_4.1.13.44_02.94.90_Ship.exe
3) Make sure ur computer is always power on...not hibernated
Step II:
1) Create 2 folders eg:flash and rom.
2) Extract flash centre.rar in flash folder
3) Extract HTC_P4350.... ship.exe in rom folder .
( Use winrar or simply double click the file. It will start the upgrade window ,click next, then hold.Go to the temp folder, u will find all the extracted content there.Copy all the content to the new rom folder. After that cancel the upgrade window.)
4)After extracting the content in the rom folder ,*****delete the SPL.nbh file ****
Step III:
Connect your phone to the computer, make sure activesync is enabled (green icon)
Step IV
1)Open the flash folder --- follow the read me file in this folder
ie
2)Run herald-uspl.exe on your computer and follow the instructions on screen.
- it will run in command window and ask u to enter the values..follow the screen
After 2/3 steps if will ask u to chk the device-- the activesync green icon in ur computer will become grey and the screen of ur mobile will be blank-white.
!!! now u have sucessfully hard spl ur device!!!
**** dont touch or remove the connection or close any program****
3)After this it will start the RUU program ,follow the instruction ,click update ( u wont find any previous ROM installed),it may or will show ERROR [240] : FILE OPEN
clik finish/cancel and exit **this program only**.
4)Now without removing anything open the rom folder and clik the ROMUpdateUtility.exe file and follow the instruction.
thats it. ur mobile will be upgraded. dont get panic...it will take some time and the mobile will be white in colour.
Thanks
Jose
C800 upgrade success
Upgraded Dopod C800 with same IPL/SPL/RADIO parameters as mjose using his directions and it worked like a charm. Am WM6 with no issues now.
Thanks POF and mjose and everyone else on the forum for your help!
WHen using Herald-USPL - it is NOT permanently HARD-SPL!!!!
Please check the SPL now - and report....
if it doesn´t show 4.70.yang - then it is only USPL = temporarly CIDunlocked= NOT HARD-SPL
thx.
How much free memory did you get by upgrading to official HTC WM6? I got only 25mb free with no extended rom install!
C800 USPL vs Hard SPL
Poppamopps, you are quite correct. The update I performed was NOT Hard-SPL. I would prefer Hard-SPL but my understanding is that it should not be used on a device with IPL/SPL below 4.0. I am 1.9 both IPL/SPL.
Is there now a HARD-SPL that is safe to use on the Dopod C800 that is below 4.0 ?
billy-the-t said:
Poppamopps, you are quite correct. The update I performed was NOT Hard-SPL. I would prefer Hard-SPL but my understanding is that it should not be used on a device with IPL/SPL below 4.0. I am 1.9 both IPL/SPL.
Is there now a HARD-SPL that is safe to use on the Dopod C800 that is below 4.0 ?
Click to expand...
Click to collapse
nope. BUT try USP for falshing an official HTC rom with higher SPL and then HArd-SPL....
NICE! I successfully upgraded my C800 to wm6 using mjose instructions. Thanks to mjose and to all those involved.
Thanks to mjose, UPGRADED
Followed exactly what mjose said. Successfully upgraded. Thanks to everybody
Any idea how to install touch flo now?
C800
ROM: 4.17.405.2 WWE
need help please!
tried updating following mjose's listed method exactly, but failed after the screen went blank, and now my c800 seems to be dead (or bricked?!). can't even power on now. is there any way to revive it, or do i now have an expensive doorstop?
longj49 said:
need help please!
tried updating following mjose's listed method exactly, but failed after the screen went blank, and now my c800 seems to be dead (or bricked?!). can't even power on now. is there any way to revive it, or do i now have an expensive doorstop?
Click to expand...
Click to collapse
managed to do a hard reset but failed to restore, the screen now is green in color and showing:
IPL 1.09.0001
SPL 1.09.0001
then it's stuck there unless i remove the battery.
can anyone help please?
longj49 said:
managed to do a hard reset but failed to restore, the screen now is green in color and showing:
IPL 1.09.0001
SPL 1.09.0001
then it's stuck there unless i remove the battery.
can anyone help please?
Click to expand...
Click to collapse
i'm assuming nobody was awake. when you were posting....but i could be wrong.
i have no idea what a green screen means other than it's green hehe... and have never flashed a dopod.. but i'll pretend it's a herald?
can you put it in bootloader mode????
soft reset(put stylus in the hole)... and hold down the camera button..
you should get the tri-color screen..
mv3 said:
i'm assuming nobody was awake. when you were posting....but i could be wrong.
i have no idea what a green screen means other than it's green hehe... and have never flashed a dopod.. but i'll pretend it's a herald?
can you put it in bootloader mode????
soft reset(put stylus in the hole)... and hold down the camera button..
you should get the tri-color screen..
Click to expand...
Click to collapse
hey thanks! yes. i've got the asian herald. i got into bootloader mode as per your suggestion - is that the one with red/green/blue horizontal bands with a thinner white band at the bottom? ok what should i do next?
i was able to run the ROM Update utility after that, but got an error 300. checked the documentation and found out that i used the wrong version for my phone, which was RUU -HTC_P4350_WWE_4.17.405.2_4.1.13.44_02.94.90_Ship.exe. would you know which one i should use?
i'm guessing your phone is not an English phone?
you need to find the native RUU for your phone.. Taiwanese Mandarin> HK Traditional? Japanese?.... if you can find it, then put your phone into bootloader and run the RUU file from your pc.
other than that, I don't know if anyone here has access to asian RUU's
doesn't look good, can't seem to find my region's wm6 rom anywhere. even tried to restore using the original wm5 rom from htc website, but still getting error 300. i think running herald-uspl.exe initially could have somehow caused some corruption.
well, i might have to visit dopod's service center soon.
thanks for your help, mv3, greatly appreciated.
did you try looking for official ruu from asia.htc.com
I suggest you load that before going to the repair centre

My Prophet don't start

Hello, I am looking for the solution to the problem of my HTC PROPHET (SPV M600 model) that does not start. In detail what I have already done:
1) I made the procedure HARD RESET following the guides published on the forum.
2) I made the procedra of BOOTLOADER and loaded Rom (I tried with several Roma) following the guides published on the forum.
3) ActiveSync 4.5 installed.
The result is that the device will not start: the screen appears with the logo of the rom (Orange or HTC) and IPL data, SPL data, etc etc, but sometimes or remains firm on this screen, or other times the screen fades plan floor.
What can I do?
Best regards
Marco
Did u already tried another rom? Which rom did u use?
Is activesync still connecting with your device?
i tried with rom of:
1) Orange
2) Qtek
3) I-Mate
the first two i can install correctly, but device don't work... when i try to install rom I-Mate, it give error message about nk.nbf file isn't compatible with prophet. i know about a program NOID COUNTRY that install every rom on prophet... do you know this program?
pincho76 said:
i tried with rom of:
1) Orange
2) Qtek
3) I-Mate
the first two i can install correctly, but device don't work... when i try to install rom I-Mate, it give error message about nk.nbf file isn't compatible with prophet. i know about a program NOID COUNTRY that install every rom on prophet... do you know this program?
Click to expand...
Click to collapse
Check on boot loader that ur device did HardSPL properly, it should look like my sig.
Also why are you trying to put OEM ROM on, why not use one of the prophet wm6/wm6.1?
Hello,
after reading your post, I rebuilt the hardreset and then starts in bootloader, but does no more. I tried with any Rom, but always starts in bootloader (IPL 2.10.0001 - SPL 2.20.0001 indicates that is a G4 right?)
is dead? because I really tried with all Rom at my disposal, but the result is this hour.
pincho76 said:
Hello,
after reading your post, I rebuilt the hardreset and then starts in bootloader, but does no more. I tried with any Rom, but always starts in bootloader (IPL 2.10.0001 - SPL 2.20.0001 indicates that is a G4 right?)
is dead? because I really tried with all Rom at my disposal, but the result is this hour.
Click to expand...
Click to collapse
It would appear that your hard SPL was not sucessfull, it should say something like SPL : 2.G4.4PDA (or something similar)
Yes you have a G4 model. what were the steps you took to do SPL? did you follow the guide? Did you unplug all ur usb connections and try other usb ports?
If you start bootloader and connect your usb to device does it say USB on the screen? Also are you using windows XP on computer?
timmymarsh said:
what were the steps you took to do SPL? did you follow the guide? Did you unplug all ur usb connections and try other usb ports?
Click to expand...
Click to collapse
I followed the guide on PROPHET_HARDRESET_BOOTLOADER on WIKI: the operation seems to succeed because I see the message on the display of operating system restored. Tested with all the usb ports, and disabling the connection usb dall'activesync.
timmymarsh said:
If you start bootloader and connect your usb to device does it say USB on the screen? Also are you using windows XP on computer?
Click to expand...
Click to collapse
USB appears on the display and use xp.
I noticed that when upgrade Rom program start, I see on the display a green bar progress, but turns red when it arrives 99%-100%. It may mean that something is not successful, despite the process ends without mistakes?
What is the devices IPL/SPL, and what brand is the device?
l3v5y said:
What is the devices IPL/SPL, and what brand is the device?
Click to expand...
Click to collapse
Hi!!!!
sorry for late answer....
IPL:2.10.0001
SPL: 2.20.0001
GSM: 02.47.21
OS: 2.10.1.22
Brand: Orange
after installing the latest rom Orange, these are the data that appear on the monitor. But still not start. It remains firm on this screen, or this screen fades slowly as reported in a previous post.
From tomorrow I will be on vacation, return to this issue by September 1 ....
a greeting and goodbye to September 1 !!!!!
pincho76 said:
Hi!!!!
sorry for late answer....
IPL:2.10.0001
SPL: 2.20.0001
GSM: 02.47.21
OS: 2.10.1.22
Brand: Orange
after installing the latest rom Orange, these are the data that appear on the monitor. But still not start. It remains firm on this screen, or this screen fades slowly as reported in a previous post.
From tomorrow I will be on vacation, return to this issue by September 1 ....
a greeting and goodbye to September 1 !!!!!
Click to expand...
Click to collapse
If you have the time, download and flash an NVID Prophet ROM from the wiki. Make sure it's NVID though!
l3v5y said:
If you have the time, download and flash an NVID Prophet ROM from the wiki. Make sure it's NVID though!
Click to expand...
Click to collapse
Hello!!!!
i'm coming back from Paxi (Greece)... very nice island... good sea... good food... very nice gals.... i liked it!!!!!!
Downloaded from Wiki "RUU_Prophet_220734_2207114_024721_NVID" and installed without problem but nothing to do: the same problem!!!
Now when it start i can see first HTC Innovation Logo, after QTECK logo with:
ipl: 2.10.001
spl: 2.20.0001
gsm: 02.47.21
os: 2.20.7.34
but after some minutes the screen fade....
i would give you some information:
- into the device ther's not memory card and sim card.
- when i charge it, led is always red, also if leave in charge for 10 hours!!! It's normal???
Ciao
Marco
If the LED is red, I'd try and find a replacement battery.
read from here http://wiki.xda-developers.com/index.php?pagename=HTC_Prophet
and here http://forum.xda-developers.com/showthread.php?t=353547
read carefully ok...

Pharos 3470 Revive

Hi! i open this Thread beacause i search for answers and i don't find them...
First thing, i will say what i done and where am i with Ruu.
I hard spl with 1.11 from PDA all soft working after then i flash it with 5 software and all have the same problem. Windows mobile image apears but remains in it... can't go forward.
Second i download RUU_Pharos_HTC_WWE-ME_1.11.456.1_4.1.13.59_03.15.90_BLUE_Ship and others original firmwares, but now it remains on Smart Mobility image and say
ONBL 2.05.0000
SPL 2.05.0000
GSM 03.37.90
OS 2.5.0.0
and i can't flash with any soft upgrade, because it work's 2% and restart, and RUU tool say check your update tool...Hard spl don't work anymore
just remains at this step..nothing happed...
Can i revive my Pharos? or i can go to trash and drop him there? (
Sorry for my english!
same problem.
please help
Hi,
You installed a ROM with a packaged SPL 2.x (2.05.0000 in your case), but AFAIK there isn't any patch for SPL versions higher than 1.11, so you can't flash anymore with any ROM. You're locked with your last ROM. You can try to ask for a patch, but i think that's not easy to obten a valid answer. You can also try to make this patch, but... good luck
can i used other htc unit hardspl?

stuck on bootloader screen

Hi,
I have tried to flash a wiza200 that was already flashed with a manila rom, I checked that it is a G4. I used TNT.20273 Professional Wizard HTC Home FREE ROM, it seems to work , romupdate utility indicated that the device was flashed successfully but it reboots on bootloader screen. I tried to reflash it it gave the same result, I tried another rom but impossible to flash it with other roms. So I downloaded the official one from the operator O2 but I got "invalid vendor" message. I searched all the possible solutions but none of them worked( wizard love also). Is there a savior here ? someone who can give me the right procedure to follow.
initially the IPL was 2.21.0001 and spl 2.21 Olipr
now the IPL is 2.21.0001 and spl 2.21
Thanks
Best regards.
You must replace the Update.exe with a MaUpgradeUT_NoID.exe . Found here in Forum . Look in "Blue Angel" for it. Be sure that you flash the right ROM with it . It will no ask...

Categories

Resources