HTC TYTN doesn't charge from USB and screen allignment problem - 8525, TyTN, MDA Vario II, JasJam General

Since I bought it with the original WM5 ROM I had two most annoying problems with it (now I run WM6):
1) When I use the car charger it will only charge the first time I plug it in. If for whatever reason I unplug it and plug it again, the damn thing won't charge from the lighter charger. This is very frustrating as you can imagine since I use igo with the screen always on that drains the battery in a few hours + bluetooth consumption + the fact that phone itself rather old + the fact that igo doesn't save routes and I have to make my route all over again!
2) My screen gets missalligned extremly often! I mean like in a few tens of minutes I have to run Allign Screen again.
These are the main reasons that I stopped using it a while back, but now I need it badly for a long trip with my car. I tried to search this forum for these problems but I couldn't make head or tails of the search results. Do you know any quick fixes for these issues?
Thank you for your time.

There is a known issue where it will charge once off a lighter socket and not again unless it is switched off. A soft reset will start it charging again. (Bit of a pain).
The screen alignment issue is dealt with extensively in other threads.
Mike

So there is no workaround for the car charging issue as of yet. That is unfortunate. Thank you for your reply.

I have the same 2 problems on my TyTN (Hermes).
Right now I'm investigating the charging problem but so far without any results. As said before, a soft reset is right now the only way to get rid of it.
The screen alignment problems are most annoying since it happens a lot really. Seen solutions for that problem in other threads. Although I don't know if I really wanna risk taking the whole device apart myself...
For now I just realign when it happens (made a shortcut to access it fast).

i had a screen alignment prob but found out it was because of the firmware i had, i could not align at all was off by 5mm, what firmware did u flash it with?

Related

Help! Weird problems on my jasjar

I have a jasjar recently and had problems turning off at 50 percent. It was working fine as long as power odesnt drop below 50 %. Then I bought a desktop charger (made in china) and started charging from there. That's when all this weird problems started.
When I put the fully charged battery inside sometimes it doesn't power on by pressing the power ubtton so I have to reset it to turn on. Sometimes it doesn't turn on with reset so I have to go to bootloader then reset just to turn it on. Sometimes it just won't turn on! If it does turn on sometimes the screen is white! When it does boot properly and go on standby. The lights blink but it won't wake up so I have to reset it. Sometimes while using it, the screen would just turn garbled white.
This don't happen all the time, Im actually typing this post using my jasjar and even if I charge the battery using the phone, it exhibits the same problems once in awhile.
SOLUTION FOUND!!! READ THE LAST THREAD
Any ideas? Could the battery be doing this or is my jasjar messed up? Please help!
I downgraded to wm 5 Helmi ROM and seems to work for now. I was using Helmi's wm6 so I don't know if that attributed to that. Will update.
Still didn't help.. Any ideas? Is my jasjar dying? Please help!
Battery issues
Here and elsewhere are postings which make it apparent that some after-market batteries don't work well with the Jasjar. Some electronic devices are relatively fussy about voltage and amperage levels, and some off-brand batteries are fairly wide of the mark in those regards. Not necessarily on the low side, either.
The problem is not limited just to computers. I had an electronic remote reading thermometer whose display went nuts; the manufacturer asked whether I was using EverReady or Duracell batteries. When I replied no, I was using Ikea batteries, they told me I had to use EverReady or Duracell batteries or I was likely to encounter the problem, and they're right: using those batteries fixed the problem. Not that the Ikea batteries were bad, mind you: their power level (voltage and amperage both) were actually too high, according to the manufacturer, and my VOM tester confirmed their assertion.
Somewhere on this forum is a link to an eBay supplier of batteries which work reliably in the Jasjar. Good hunting! Cheers,
Thanks but I'm using the original battery. So do you think that the desktop charger did something to the battery?
may be it caused by a desktop charger. When i used a chaeger made in chine for my alpine, sometime the screen goes white, or ALL buttons seems die (All button didn't work). The most terrible is that charger make my dive hard reset 2 times (first time i din't realise if it cause by my charger, then i just install all progs but when i charge, it hard reset again).
Even for 5 days after i bought it run well, except the ringtone goes on silent every time i charging.
Now i throw away that thing.
So its the charger!! GRRR...Anyways, even when I'm using the Jasjar to charge, everything is the same. Lockups from standby, white screen..You think I should try another battery? Any ideas?
Weird stuff / battery related?
Hi there,
dont know if anyone is reading this thread coz it is kinda old, but i have the same probs mention as above. I have the orginal bat and charger which came with the device. I also uses a car charger sold from my phone provider.
now after 14 months i have the weirdest things like shutting down randomly when the bat is about 58 thru 50 percent. I can not start the device again coz it stops in the middle of the boot process. It only starts when i connect it to a laptop by usb or to the standalone charger...
I tried differnt roms found here and radio roms but it doesnt help...
my guestion: does any one know if this prob is solved when I buy a new battery? or is it wise to thro out this universel suck device ( I have had so much probs with this device so neglect my tone...)
XCube said:
Hi there,
dont know if anyone is reading this thread coz it is kinda old, but i have the same probs mention as above. I have the orginal bat and charger which came with the device. I also uses a car charger sold from my phone provider.
now after 14 months i have the weirdest things like shutting down randomly when the bat is about 58 thru 50 percent. I can not start the device again coz it stops in the middle of the boot process. It only starts when i connect it to a laptop by usb or to the standalone charger...
I tried differnt roms found here and radio roms but it doesnt help...
my question: does any one know if this prob is solved when I buy a new battery? or is it wise to thro out this universel suck device ( I have had so much probs with this device so neglect my tone...)
Click to expand...
Click to collapse
I bought my Universal (Jasjar), used, almost a year ago and use it daily. To date, I haven't had this problem, but I'm anticipating it. Yeah, I'd say it's almost surely your battery (they don't live forever), just be careful to replace it from a reliable source.
Sorry you don't like the device; I've thoroughly enjoyed mine! Cheers,
Hi,
I guess u r right, batteries will die. So I ordered a new one, I will let you guys know if it helps. I bought the qtek 35H00058-00M battery which is the orginal bat
The thing is, normally will a battery be faster drain so it would become faster 0 or 10 precent, instead this piece randomly shutting down or switches off in the middle of a phone call.
I have a Blue Angel as well, now for more then 2 years, which is charger daily just like mine unversal. The batt of the Blue Angel outruns the uni with bat life. Never had this weird stuff with the ba, like shuttingdown without a warning.
Well I will see if a new bat will fix the trouble, tomorrow my new bat will arrive.
cheers.
I also have the same issue with the 02 Exec. It switches it's self off when the battery reaches below 50%. I have ordered a new battery. Will let you know if this still happens once it arrives.
Well,
I already knew it but now its for sure at my end. HTC and ms together gives u pretty expansive CRAP.
Got my new battery which was carefully chosen because of other rumours of battery problems. I bought exactly the same battery from QTEK as the original.
Yesterday i got the battery, left it alone to get on room temp. this morning switch it with my old battery.
1. First thing what i found strange was that my **** device said it was at 100%
2. after 45 min I had the same bat prob as with my old battery
3. device can not be started on bat power, which would let u think that the bat would be ZERO procent. However turning the device on when on wall power this **** device says that the bat is 100%, but disconnecting it from the wall power it shutdowns right away.
conclusion:
the new battery is worse then the old bat. the only difference between them is the serial number. same type same manufacturer.
I was already think of buying a non HCT / Micro**** mobile device, but today after 14 months of trouble and losing important phone calls I am going to say good bye to this universal crap.
I wise u the best with our device but for me it ends here.
UPDATE:
Used a 3800 mah battery from expansys, made in Taiwan by Dyna and still same problems...not battery related at all...Anybody got a mainboard they can sell me...even a broken miniusb.
Problem and solution found
The Problem is a faulty voltage controller in the mainboard causing Bulverde CPU to hang and give funny colors to the screen
Solution is to disable Cpu scaling of Bulverde by using pocket hack master and setting speed at 312mhz before turning it of or closing the screen. You could always set it at 520 when using it but before turning it off make sure speed is 312. Hopefully this helps others with this problem.

Tytn Won't Charge

I have noticed that for the last week my Tytn won't always charge itself up either when its in its cradle or is being charged via the charging lead.
I have no idea what has brought this on. The solution I am using at the moment is to soft boot, which seems to solve the problem for a while. For the techies on here I am using the standard HTC Win5 Rom, straight out the box.
Has anyone come across this problem and, if yes, knows what the solution is please? It was only because my low battery alarm kicked in the other day that I realised there was a problem.
As I use the kit for work I cannot afford to have it not charge up.
Many thanks in advance for your help.
WB
Caveat - Yes, did search first on here and elsewhere before posting.
Could be hardware (at Device) / could be software. Without testing these things out it's impossible to say. I suppose a quick test of the physical contacts of the device would be to switch on and connect the charger and by gently moving the connection, see if the amber charging LED goes on off.
In the end I always think with this kind of problem a hard reset saves a lot of time testing this and that. If there is nothing you can pin down as an obvious change/installation you made before this started, then I'd do a hard reset.
Of course you are fully prepared for this with full backups taken at key installation stages?? - Hope so.
Mike
The only thing I've heard of is that using USB cables/cradles, car chargers and non-standard wall chargers (such as for motorola) are ok for trickle charging but if the battery goes low you need to use the original wall charger supplied with the phone.
I know this was the problem on my Wizard - wouldn't charge a low battery with a motorola charger but fine with the original.
Mike,
I think I will do a hard reset as a last, last, resort only if all other options are well and truly exhausted. I rebuilt the damned thing for the umpteenth time only 2 weeks ago and I absolutely don't want to go through that pain again.
The frustrating thing is that for the first time since I owned the Tytn (6 months) all the problems I did not know about before I bought it had finally been resolved (excepting the freezing of TomTom, which still remains outstanding).
So just when I thought I could finally start to rely on the Tytn as a fully functioning relible working tool we get this.
I owned a Sony P900 for over 3 and a half years as a business tool (grant you the PDA functionality was a tad restricted compared to the Tytn) and it never failed me once! If it wasn't for a problem with the touch screen and me thinking it was time for a change I would still be using it today.
Anyone else any other suggestions on this problem please? Wiggling the charging cable in the mini-usb port makes no difference. Only a reboot does at this time.
So damned frustrating!
WB
hungry TyTN
Hi,
I have a similar problem. I had a go for the WM6 from LVSW (2007-05-19) and the latest Radio (1.41.00.10) and a brand new out of the box TyTN.. First thing I noticed was that the unit discharges itself very quickly. I've tried various radios without any good luck too. I think it killed my battery, at least it went so low that I could'nt recharge it normally. I had the RED LED blinking fast, constant RED and sometimes AMBER. My tip is to never let the battery fully discharge here.. I had to kickstart it with 3 AA-batteries in serial, and hooked up + and - wires to the TyTNs battery so it could have a little power, or else the TyTN would not charge it anymore. I assumed it could be my old SIM and/or the battery, so I went to th store and got a new battery as replacement for testing this. I am now able to charge, but I the power consumption is far beyond what I expect, it is like 341 ma read with ABC Power Meter....! Even with radio off, wifi off, receive incoming beams off, BT off, screen to minimum brightness, nada... I was expecting a lot less... This hungry device will not last many hours, and the battery does even produce much heat during standby operation, which is not good besides from a hand-warmer in the pocket during winter time maybe... I have also tried using Bandswitch to disable UMTS as maybe the UMTS reception here is not super good, but still working... Even talking on the phone while charging it drains the battery heavily.... to empty...
Besides from all this the WM6 from LVSW seems to be super quick and stable, maybe the very best one to pick for a HERMES.
I am desperate to find a conclusion here...
heeelp..
Update:
I happened to purchase a faulty device!!! There was indeed a HW error on my brand new device so I got it swapped with another one that works. Not all problems are SW-bugs..
Thought I would come back on this thread.
In the end I had to do a hard reset and rebuild as other problems started to manifest themselves and rebuilding became the easiest option.
Rebuilding has solved the problem; however it might interest you to note that this time I rebuilt the Tytn just like I would build a PC. The OS built itself first, with its associated apps, then I added any other additional OS tools, eg SPB Mobile Shell. I then grouped my apps into a logical order and installed them one by one.
After each install I rebooted the PPC, checked that the last app installed ran ok, then tested every other app to see if they ran as well BEFORE installing the next app. This process was a little tedious but it seems to have paid off.
I have to say though that having rebuilt this piece of kit from scratch at least 20 times in the last 6 months, I just cannot count on it as a reliable business tool in the same way as I did with my previous Symbian device. Shame given how much I spent on it.
When my next upgrade is due a Windows mobile device WON'T be on my list!
WB
Wacky - Get a full back-up tool like SPB backup and you can avoid all that pain. Hard Reset to Restoring a full backup - 10 minutes maybe. Much better than re-installing all those apps everytime you hard reset. And you can create a backup before and after each installation if you wish.
Mike
Mike,
Thanks for the tip. Must admit I had not thought of using SPB backup in the way that you suggest (can't see the wood for the trees sometimes).
Now that I think I have a stable system I will back it up using this tool and create a "line in the sand", in terms of a good system backup.
I still remain to be convinced on the stability/suitability for sustained business use though.
Appreciate your input.
WB
Similar (Battery Meter) Problem
This week, my phone reset for some reason and came up with the screen which shows the current IPL and SPL. The phone still has all the apps and data I installed, so it was not a hard reset. This happened with a 1/2 charge on the battery.
Since that happend a full charge now shows as a 1/2 charge only on the meter and this is as high as the meter will show. The phone still lasts just as long, so there is no physical battery problem.
Anyone know how to fix this without a true hard reset.
Thanks
Mardig,
The only suggestion I have is to hard reset the unit and then rebuild it from scratch. Worked for me.
In any case it may be advisable to do this as it sounds like you have other problems.
Once rebuilt I suggest you take up Mike Channon's suggestion to get a tool and backup the device. That way if you have further problems you at least have a line in the sand to refer back to.
By the way, I am not ruling out a hardware problem in your case. However my starting point would be my suggestions above.
Good luck
WB
Strange TyTN behavior when charging
I bought a car charger for my TyTN and used it for ~4-5 months without a problem. One day a fuse went off and after replacing it with a new one and connecting to TyTN, a TyTN stopped charging completely. I checked at home with an original wall charger - nothing. I was stupid enough to try the same car charger with my second TyTN - not surprisingly it burned the other one too :-(
I got them both fixed, a car charger replaced with a new one, so everything should have been working fine. The following happened:
1. First time a car charger is connected, it works fine and the TyTN is charging.
2. Disconnecting a charger and reconnecting it back after couple of seconds restart charging, however this stops after 1 sec and the screen shows as it is not connected.
3. Repeating step 2 does nothing - no charging starts at all.
4. Soft reset - go back to step 1.
5. When TyTN off and car charger connected - charging is working - amber light is on.
6. Wall charger (original), TyTN on or off - charging is working - amber light is on.
I did hard reset as well thinking it might be a broken driver problem, but it didn't help. Tomorrow will try to reload ROM.
Any ideas?
Help will be appreciated (before I take it back to lab and spend another $40 for repair)
Cheers
eznil said:
I bought a car charger for my TyTN and used it for ~4-5 months without a problem. One day a fuse went off and after replacing it with a new one and connecting to TyTN, a TyTN stopped charging completely. I checked at home with an original wall charger - nothing. I was stupid enough to try the same car charger with my second TyTN - not surprisingly it burned the other one too :-(
I got them both fixed, a car charger replaced with a new one, so everything should have been working fine. The following happened:
1. First time a car charger is connected, it works fine and the TyTN is charging.
2. Disconnecting a charger and reconnecting it back after couple of seconds restart charging, however this stops after 1 sec and the screen shows as it is not connected.
3. Repeating step 2 does nothing - no charging starts at all.
4. Soft reset - go back to step 1.
5. When TyTN off and car charger connected - charging is working - amber light is on.
6. Wall charger (original), TyTN on or off - charging is working - amber light is on.
I did hard reset as well thinking it might be a broken driver problem, but it didn't help. Tomorrow will try to reload ROM.
Any ideas?
Help will be appreciated (before I take it back to lab and spend another $40 for repair)
Cheers
Click to expand...
Click to collapse
This is a known issue. It also appears you've realised the soft reset workaround:
In Car charging
(May be relevant to USB/Mains charging also)
Hermes only charges when switched off
Pulling out charger lead (or interrupting power supply) while charging in car (with device on or off ) may result in Hermes only charging while turned off
Possible Solution:
a.) Connect charger with power on
b.) Switch on Hermes
c.) Soft reset whilst connected
Hermes should now charge whilst on or off.
I charge mine in the car but I do not use a car charger but a 12 volt to 240 volt inverter - so I can plug in a mains charger. Never have problems with this and I can also use it to power my laptop.
Examples here of cheap and expensive ones - small ones and large ones:
http://www.sailgb.com/c/12v_inverters_converter/
Mike
mikechannon said:
This is a known issue. It also appears you've realised the soft reset workaround:
In Car charging
(May be relevant to USB/Mains charging also)
Hermes only charges when switched off
Pulling out charger lead (or interrupting power supply) while charging in car (with device on or off ) may result in Hermes only charging while turned off
Possible Solution:
a.) Connect charger with power on
b.) Switch on Hermes
c.) Soft reset whilst connected
Hermes should now charge whilst on or off.
I charge mine in the car but I do not use a car charger but a 12 volt to 240 volt inverter - so I can plug in a mains charger. Never have problems with this and I can also use it to power my laptop.
Examples here of cheap and expensive ones - small ones and large ones:
http://www.sailgb.com/c/12v_inverters_converter/
Mike
Click to expand...
Click to collapse
Hi Mike.
Thanks for your prompt response.
I did read that thread, however it seems that it doesn't explain point 2 in my explanation, does it?
Update: tried the method explained, however the situation is still the same - both points 2 and 5.
Regarding the DC-AC inverter - do you use a wall charger or USB output (if there is one, I found one that has both main and USB).
Cheers
eznil said:
Hi Mike.
Thanks for your prompt response.
I did read that thread, however it seems that it doesn't explain point 2 in my explanation, does it?
Cheers
Click to expand...
Click to collapse
Unless I misunderstand something - one of the primary causes of the problem is the disconnection whilst charging leading to a refusal to charge when re-connected. To quote my post:
"Pulling out charger lead (or interrupting power supply) while charging in car (with device on or off ) may result in Hermes only charging while turned off "
I realise of course this does not explain things and is just a statement about what happens.
Mike
mikechannon said:
Unless I misunderstand something - one of the primary causes of the problem is the disconnection whilst charging leading to a refusal to charge when re-connected. To quote my post:
"Pulling out charger lead (or interrupting power supply) while charging in car (with device on or off ) may result in Hermes only charging while turned off "
I realise of course this does not explain things and is just a statement about what happens.
Mike
Click to expand...
Click to collapse
THe funny thing is that the other TyTN I have doesn't suffer the same behavior and charges fine, even though I disconnected and connected many times while charging.
Yeap, it's strange, unexplainable and most of all extremely annoying.
Thansk a lot for your help.
Solved!!!
Hi.
I am happy to tell that I managed to figure out how to overcome that problem. I hope it will work for all users - I tried it with 2 different TyTNs and it was OK.
The solution is to plug/unplug the USB charger only when the device is off - not a complete shutdown by long press on Power button, but a short one.
If it's OK, when plugging the lead the power button lights up in <1 sec. If not, it takes ~5 sec to go on.
Best regards,
i discovered today....when i plugged my hermes into the car charger, that it wasnt charging.
after a soft reset it charged. an then.....no problems untill about 22:00 pm. i plugged it again and...same thing, it needed a reset to charge.
what could cause this? igo may way and bluetooth gps. coz i think this is the reason.
gangstar said:
i discovered today....when i plugged my hermes into the car charger, that it wasnt charging.
after a soft reset it charged. an then.....no problems untill about 22:00 pm. i plugged it again and...same thing, it needed a reset to charge.
what could cause this? igo may way and bluetooth gps. coz i think this is the reason.
Click to expand...
Click to collapse
Please read the thread - this strange behavior is described in details.
Try the solution in my post above - it workes for me, hoefully for you too.
Goos luck.

hermes turning itself off

i have developed a problem with my hermes. it will just turn itself off even with a fully charged battery. i think the issue may be connected with the new case i bought. it is one of the monstech snap on cases. when i was first installing it, it caused the keyboard to pop loose(the actual keypad part), but it snapped right back in place. when it shuts itself down you can still see the screen image, but just barely. i was just wondering if anyone had any idea of what might be causing the issue and if it is something i can do to fix it myself since i assume that the warranty is void since the phone has been superCIDed. any help would be greatly appreciated.
hi
had the same problem. what i did was to turn on all functions (wlan,gsm phone, data transfer, bluetooth) run a bunch of programs in the background
then turn of the screen ( tapping the power button once)
the battery will then start to slowly drain itself and once you recharge the battery, the phone should be quite ok afterwards

JASJAM not charging...Need Help

Hi,
I have a Jasjam PPC. But the problem is that it's not charging at all. When I put it in charge only red light glow either with battery inserted or battery removed. So, is it time to replace my battery or there is some problem with the Jasjam? I have done resetting during the charge but its not working also. Since my battery is totally drained up so there's not any kind of screen light during pressing power button.
PLZ I NEED HELP...........
Thanks.
hayabusa_ryu said:
Hi,
I have a Jasjam PPC. But the problem is that it's not charging at all. When I put it in charge only red light glow either with battery inserted or battery removed. So, is it time to replace my battery or there is some problem with the Jasjam? I have done resetting during the charge but its not working also. Since my battery is totally drained up so there's not any kind of screen light during pressing power button.
PLZ I NEED HELP...........
Thanks.
Click to expand...
Click to collapse
Usually caused by something that causes the battery to drain below 10%. Then you can get the RLOD. The charging circuit gets locked up and won't allow the device to charge. A pesky problem, but at least you have the RLOD, if you didn't then it could be the motherboard fuse.
So some things to try, non of them guaranteed and sometimes it works after trying these things several times over:
http://forum.xda-developers.com/show...22&postcount=6
Mike
Thank you very much for the suggestion. I have tried the recommended first 2 methods and last method is still left to try but I feel that Its time to buy a new battery becaz the battery is 2 years old. And I also feel that its totally RLOD problem becaz I carry 2 phones and don't pay much attention to this jasjam therefore I dont usually charge it frequently. I have left it uncharged for many times and thus there isn't any problem with motherboard fuse in my opinion. I will try my most to make the battery work.
One suggestion needed. The place where I live dont have any Imate shop but the HTC shop is near. Since TyTyn and Jasjam are nearly the same device should I buy the tytyn's battery and insert it in JASJAM.
Again ur reply needed.
thanks
hayabusa_ryu said:
Thank you very much for the suggestion. I have tried the recommended first 2 methods and last method is still left to try but I feel that Its time to buy a new battery becaz the battery is 2 years old. And I also feel that its totally RLOD problem becaz I carry 2 phones and don't pay much attention to this jasjam therefore I dont usually charge it frequently. I have left it uncharged for many times and thus there isn't any problem with motherboard fuse in my opinion. I will try my most to make the battery work.
One suggestion needed. The place where I live dont have any Imate shop but the HTC shop is near. Since TyTyn and Jasjam are nearly the same device should I buy the tytyn's battery and insert it in JASJAM.
Again ur reply needed.
thanks
Click to expand...
Click to collapse
To the best of my knowledge the batteries are the same. My concern is that a new battery will not solve a "locked up" charging circuit. If however it is a bettery fault then it will cure the problem - and a different battery has been known to unlock the circuit, thus allowing the old battery to start charging again.
You are correct about the fuse being OK. The red LED will not light if the fuse is blown.
Mike
Thanks a ton for your reply. And I gonna do all of your provided tricks to cure my JASJAM's RLOD disease.
I need some days to update the result. So I will let u know if i get my device working as soon as possible.
Thanks again for the help.
Thanks my phone's battery is charging again.
But i got one problem and that's my phone is showing that its speaker is on. there's speaker icon always on the top of the start menu taskbar although I cant switch on speaker in call and in some program. How to set it to default? I dunno want to reset my PPC.
hayabusa_ryu said:
Thanks my phone's battery is charging again.
But i got one problem and that's my phone is showing that its speaker is on. there's speaker icon always on the top of the start menu taskbar although I cant switch on speaker in call and in some program. How to set it to default? I dunno want to reset my PPC.
Click to expand...
Click to collapse
First I'm pleased you got it charging again. Please tell us what you did that got it working - new battery?, one of the "tricks" mentioned above??
Regarding the speaker problem. When you tap the speaker icon I assume you get two sliding volume controls - one for earpiece and one for rear loudspeaker?? I also assume you have both set correctly??
If you have the volume on both set correctly, we need to know if you get sound from the rear speaker on any programs at all. Can you play music for example. If the answer is NO then I suspect your rear speaker push on connector has slipped off (not uncommon). If so look here:
http://forum.xda-developers.com/showpost.php?p=1376254&postcount=2
If however you do get sound from the rear loudspeaker on some applications, then the above is not your problem.
Mike
I think that the second option worked for me if I am right.
And for the speaker problem, I think that you didn't understand my question.
My rear speaker works during music or in programs. But the only problem is that when I switch the speakerphone(loudspeaker) mode during the call, it's not working(not rear one). And the speakerphone icon which we see only during call is showing all the time, that's the problem and I cant switch to loudspeaker during the calls even if the loud icon is always there. I hope u understand the problem or I will post the picture.
Thank you for giving your precious time.

HD2 won't sleep!

Hi, wonder if someone else has had this problem.
My HD 2 will only sleep when on mains power. If it on battery when I put into sleep with the on/off button it comes back on after 1.5 seconds. Same if you wait 30 secs for it to go into sleep. To fix it (temporary) I have to put it on the mains for about a minute and then it behaves itself until the battery is about 50% and then it won't sleep again. This obviously drains the battery.
I have 'hard reset' the device and it is still the same. I also updated the rom from Vodafone support site. Still can't fix it.
Can anybody out there help please, it's driving me mad!
I have this happen every so often. fixed by plugging into the usb cable (doesn'tneed to be plugged in). what I understand happens is in the usb port a connection gets wobbled and stops sleep. sometimes I have to plug it in and out a couple of times.
Thanks
Thanks, didn't try it without power. I'll just carry a mini usb connector with me! Thanks again.
that's what I've started doing.
The USB insert actually doesn't work
Hi, tried the fix suggested but it doesn't work for me. I have to have the power supply live to make a difference.
Any other ideas?
sometimes it can take a few attempts. I normally soft reset first to see if that fixed it first. other than that I don't know.
sorry!
mine's started doing this now.. yey! rinses the battery too while its stuck on.
Tried a hard reset, even a different ROM and hasn't fixed it.
I'll try a different radio next
Anyone else got any ideas? is there some software that can monitor inputs to see what it is that's waking it up?
Spike
^ different radio didn't fix
Hey.
I had this, but after a while it didn't only do it on mains.
It started to do it all the time, and as you can imagine that was killing the battery.
I tried everything! took everything back to exactly how I got it and it still did it.
so I took it in for repair, they sent it back to me and it had clearly been opened up, and the screen was brand new.
If yours is still under warenty, take it to get fixed.
I spent a little over a month looking fro a fix and nothing worked at all.
Last 3 days i also have this problem....
Anyone found what is causing it or sending it for repair is the only thing to do..
anyone please?...
Press a button .. fixed
Haha
Mine does this too all of the sudden.
There is a very, very easy fix for this...
press the right lower button (The hang-up button)
Battery life is extended from 1 day max to 2-3 days standby even!
It used to go to sleep automatically tho.
I think I probably 'tweaked' it with the tweaking tools and that's why
it does it. I'm too lazy to turn it off - and - to be honest - it's good if it's on all the time. At least my GPS won't just stop the readings I take all of the sudden.
And after I'm all done playing with Navigation, I can still press the little button.
(It really IS NOT that much of a problem to quickly press it)
Stingraybass said:
Hi, wonder if someone else has had this problem.
My HD 2 will only sleep when on mains power. If it on battery when I put into sleep with the on/off button it comes back on after 1.5 seconds. Same if you wait 30 secs for it to go into sleep.(
Click to expand...
Click to collapse
Same problem here, have made hard reset, but still have the problem!
janne_s said:
Same problem here, have made hard reset, but still have the problem!
Click to expand...
Click to collapse
You might want to install the S2U2 program, and let it manage your power settings. I've found it to be much steadier and more reliable, without those sudden wake-ups and battery draining issues.
I don't think it has anything to do with software.
It is clearly a hardware issue
I had the same problem. After inspecting the usb close, i found that there is some dirt and/or corrosion at the contacts.
I cleaned them up using some spray for electic contacts and problem has gone for almost 1 week now.
I read somewhere on XDA that an other member tryied the same thing, problem solved but came back after a while...
Anyway the fact that i cleaned the usb and the problem is gone for now shows that is clearly a problem with this part of the phone..
solved
i two have had this problem and have just found out how to sort it out. basically i tried everything new radio, rom, getting rid of CHT
and in the end all it was is the usb connection!!!!
all you have to do when unplugging your usb cable is make it come out on a angle left to right. there are obviously some very delicate contacts that get knocked out of kilter making the phone think its still on mains power when its not hence never turning off
you can confirm this error by unplugging your phone going into backlight settings and seeing if you can adjust you light setting on battery power if when you adjust your light setting nothing happens you got the same prob as me
Well, mine was fixed by a hard reset. Been testing it since, and it hasn't failed to go to sleep now.
Since there's a few different "fixes". might be a couple separate actual causes.
Started facing same problem when was on hols in +40 and quite humid atmosphere. Connecting cable helps but only if the cable is plugged in power socket or computer. And that is actually a problem as I do switch often between Android and WM and after restart HD2 doesn't go to sleep
Did this two months ago with good results ;-)
mrlard12 said:
i two have had this problem and have just found out how to sort it out. basically i tried everything new radio, rom, getting rid of CHT
and in the end all it was is the usb connection!!!!
all you have to do when unplugging your usb cable is make it come out on a angle left to right. there are obviously some very delicate contacts that get knocked out of kilter making the phone think its still on mains power when its not hence never turning off
you can confirm this error by unplugging your phone going into backlight settings and seeing if you can adjust you light setting on battery power if when you adjust your light setting nothing happens you got the same prob as me
Click to expand...
Click to collapse
When I suffered from this problem a couple of months ago, I was flummoxed at first.
But then I decided to use a strong (20 diopter) magnifying glass to look at the ports and buttons of the phone. I could not imagine the amount of gunk I found inside the USB slot.
I cleaned with a very very small cotton swab dabbed in cleaning alcohol and wound around a pin and the problem was solved. Power consumption at rest went down from 30-40 to 4-9 mAh.
I now do this every few weeks.
I try the following, it works :
http://forum.xda-developers.com/showthread.php?p=8010471#post8010471

Categories

Resources