I have a jasjar recently and had problems turning off at 50 percent. It was working fine as long as power odesnt drop below 50 %. Then I bought a desktop charger (made in china) and started charging from there. That's when all this weird problems started.
When I put the fully charged battery inside sometimes it doesn't power on by pressing the power ubtton so I have to reset it to turn on. Sometimes it doesn't turn on with reset so I have to go to bootloader then reset just to turn it on. Sometimes it just won't turn on! If it does turn on sometimes the screen is white! When it does boot properly and go on standby. The lights blink but it won't wake up so I have to reset it. Sometimes while using it, the screen would just turn garbled white.
This don't happen all the time, Im actually typing this post using my jasjar and even if I charge the battery using the phone, it exhibits the same problems once in awhile.
SOLUTION FOUND!!! READ THE LAST THREAD
Any ideas? Could the battery be doing this or is my jasjar messed up? Please help!
I downgraded to wm 5 Helmi ROM and seems to work for now. I was using Helmi's wm6 so I don't know if that attributed to that. Will update.
Still didn't help.. Any ideas? Is my jasjar dying? Please help!
Battery issues
Here and elsewhere are postings which make it apparent that some after-market batteries don't work well with the Jasjar. Some electronic devices are relatively fussy about voltage and amperage levels, and some off-brand batteries are fairly wide of the mark in those regards. Not necessarily on the low side, either.
The problem is not limited just to computers. I had an electronic remote reading thermometer whose display went nuts; the manufacturer asked whether I was using EverReady or Duracell batteries. When I replied no, I was using Ikea batteries, they told me I had to use EverReady or Duracell batteries or I was likely to encounter the problem, and they're right: using those batteries fixed the problem. Not that the Ikea batteries were bad, mind you: their power level (voltage and amperage both) were actually too high, according to the manufacturer, and my VOM tester confirmed their assertion.
Somewhere on this forum is a link to an eBay supplier of batteries which work reliably in the Jasjar. Good hunting! Cheers,
Thanks but I'm using the original battery. So do you think that the desktop charger did something to the battery?
may be it caused by a desktop charger. When i used a chaeger made in chine for my alpine, sometime the screen goes white, or ALL buttons seems die (All button didn't work). The most terrible is that charger make my dive hard reset 2 times (first time i din't realise if it cause by my charger, then i just install all progs but when i charge, it hard reset again).
Even for 5 days after i bought it run well, except the ringtone goes on silent every time i charging.
Now i throw away that thing.
So its the charger!! GRRR...Anyways, even when I'm using the Jasjar to charge, everything is the same. Lockups from standby, white screen..You think I should try another battery? Any ideas?
Weird stuff / battery related?
Hi there,
dont know if anyone is reading this thread coz it is kinda old, but i have the same probs mention as above. I have the orginal bat and charger which came with the device. I also uses a car charger sold from my phone provider.
now after 14 months i have the weirdest things like shutting down randomly when the bat is about 58 thru 50 percent. I can not start the device again coz it stops in the middle of the boot process. It only starts when i connect it to a laptop by usb or to the standalone charger...
I tried differnt roms found here and radio roms but it doesnt help...
my guestion: does any one know if this prob is solved when I buy a new battery? or is it wise to thro out this universel suck device ( I have had so much probs with this device so neglect my tone...)
XCube said:
Hi there,
dont know if anyone is reading this thread coz it is kinda old, but i have the same probs mention as above. I have the orginal bat and charger which came with the device. I also uses a car charger sold from my phone provider.
now after 14 months i have the weirdest things like shutting down randomly when the bat is about 58 thru 50 percent. I can not start the device again coz it stops in the middle of the boot process. It only starts when i connect it to a laptop by usb or to the standalone charger...
I tried differnt roms found here and radio roms but it doesnt help...
my question: does any one know if this prob is solved when I buy a new battery? or is it wise to thro out this universel suck device ( I have had so much probs with this device so neglect my tone...)
Click to expand...
Click to collapse
I bought my Universal (Jasjar), used, almost a year ago and use it daily. To date, I haven't had this problem, but I'm anticipating it. Yeah, I'd say it's almost surely your battery (they don't live forever), just be careful to replace it from a reliable source.
Sorry you don't like the device; I've thoroughly enjoyed mine! Cheers,
Hi,
I guess u r right, batteries will die. So I ordered a new one, I will let you guys know if it helps. I bought the qtek 35H00058-00M battery which is the orginal bat
The thing is, normally will a battery be faster drain so it would become faster 0 or 10 precent, instead this piece randomly shutting down or switches off in the middle of a phone call.
I have a Blue Angel as well, now for more then 2 years, which is charger daily just like mine unversal. The batt of the Blue Angel outruns the uni with bat life. Never had this weird stuff with the ba, like shuttingdown without a warning.
Well I will see if a new bat will fix the trouble, tomorrow my new bat will arrive.
cheers.
I also have the same issue with the 02 Exec. It switches it's self off when the battery reaches below 50%. I have ordered a new battery. Will let you know if this still happens once it arrives.
Well,
I already knew it but now its for sure at my end. HTC and ms together gives u pretty expansive CRAP.
Got my new battery which was carefully chosen because of other rumours of battery problems. I bought exactly the same battery from QTEK as the original.
Yesterday i got the battery, left it alone to get on room temp. this morning switch it with my old battery.
1. First thing what i found strange was that my **** device said it was at 100%
2. after 45 min I had the same bat prob as with my old battery
3. device can not be started on bat power, which would let u think that the bat would be ZERO procent. However turning the device on when on wall power this **** device says that the bat is 100%, but disconnecting it from the wall power it shutdowns right away.
conclusion:
the new battery is worse then the old bat. the only difference between them is the serial number. same type same manufacturer.
I was already think of buying a non HCT / Micro**** mobile device, but today after 14 months of trouble and losing important phone calls I am going to say good bye to this universal crap.
I wise u the best with our device but for me it ends here.
UPDATE:
Used a 3800 mah battery from expansys, made in Taiwan by Dyna and still same problems...not battery related at all...Anybody got a mainboard they can sell me...even a broken miniusb.
Problem and solution found
The Problem is a faulty voltage controller in the mainboard causing Bulverde CPU to hang and give funny colors to the screen
Solution is to disable Cpu scaling of Bulverde by using pocket hack master and setting speed at 312mhz before turning it of or closing the screen. You could always set it at 520 when using it but before turning it off make sure speed is 312. Hopefully this helps others with this problem.
Related
Hello,
I know that there have been previous discussions on battery problems, but after doing my best to read through, I'm still a bit unsure and wasn't able to find an exact solution nor an identical match to my problem.
My problem is that recently my XDA Exec has gone from lasting around 6 or 7 hours to less than 20 minutes when using GPRS on lowest backlight and no sound.
When it goes off, the battery meter still has aroubd 95% left showing so it is really quite puzzling. What happens is that after around 20 minutes, the LCD just fades away into black and the device completely dies, no sign of life.
Trying to turn it on or reset it both result in a soft reset, and the device comes up to the O2 Logo fine, loads for a few seconds, gets to the WM logo screen and then the LCD fades away and it dies again.
The only solution is to connect it up to the power, after which it then works fine while powered, indicating some sort of power or battery problem. When plugged back in, the battery meter is still at around 90% or so and goes all he way back up to 100%.
Does anyone have any ideas as to what might be the problem and what might be a good solution? Would buying a new battery help (although the battery meter does indicate the battery is still nearly full and estimates around 6 hours usage)? Do I need to send it in for repair?
Thanks very much in advance, any advice or help would be greatly appreciated
Quboid
You should wait for the experts to help but from my intuition it really sounds like a battery problem. Lithium batteries can act very strangely if they are faulty. If nothing else works you may want to try and get a new one. Better than throwing the device in my opinion.
I don't know that I'd count myself with the "experts," but my similar problem was solved by getting a new battery. Mine too would "fade" off and then only come back on when it was plugged in. And the "fade" happened at around 70% power, so by all appearances it should have had much more time left. This was a battery that was about 15 months old, but with quite a bit of daily usage.
Go for the new battery.
Welcome to about 10 months ago when this happened to almost everybody. Get a new battery, problem solved.
Thanks for the replies,
I guess I was just surprised it might be the battery itself that's dieing, seeing as the fact it still shows charge and that it doesn't get heavy usage, only a few times per month and it's only just gone a year and furthermore, compared to my old Pocket PC which had a lot more usage and still is working fine seven years later.
Am I right in thinking that this is what I need to purchase? Wouldn't want to get the wrong thing
Thanks again for the help
Quboid said:
Am I right in thinking that this is what I need to purchase? Wouldn't want to get the wrong thing
Click to expand...
Click to collapse
That's the one!
Right, i have looked at most of these battery problems and my issue is the same as Quboid so, of I toddle off and purchase a new battery and guess what..!! Still the same, the damm thing shuts down with around 85% full charge.
What I cannot accept is the fact that this problem suddenly appears after no battery issues for the 12 months of owning the unit, you would have thought if the battery was going belly up that it would gradually happen but no...it just happens..!!, now is it that the new battery is dead...not so sure becasue at the place i work there are several universals around amd i have tried different batteries and still the same problem...
Could it be something to do with the unerversal thinking the battery is dead or is it reading a false level of charge...do you need to hard reset when adding a new battery..??
This is getting me down, after months of no problems there is nothing worse than a dead machine after 20 minutes of a full charge.
on ebay you can find batteries that could be docked into a sort of charger and charge without the use of the fone.
are these any good?
It depends on the type of the battery. If you just take your phone to the shop where you bought it, and have them give you a new battery, you'll be fine.
The original batteries only last about 6-10 months, and then they will need replacing.
Thats what i have, a new battery from the suppliers...
I've got the same problem.
My XDA dies after about ten minute's use with a full battery. I have purchased a new battery and it still dies.
I've reinstalled the ROM -- which is the standard latest O2 ROM.
I've tried it on the O2 setup, and the non-O2 setup.
I'm running nothing extra software wise -- even completely clean it dies.
I wanted to keep it running until the Omni or I-Mate Ultimate 7150 comes out, so this is really a pain.
Any other suggestions gratefully received.
hmm
theambler said:
I've got the same problem.
My XDA dies after about ten minute's use with a full battery. I have purchased a new battery and it still dies.
I've reinstalled the ROM -- which is the standard latest O2 ROM.
I've tried it on the O2 setup, and the non-O2 setup.
I'm running nothing extra software wise -- even completely clean it dies.
I wanted to keep it running until the Omni or I-Mate Ultimate 7150 comes out, so this is really a pain.
Any other suggestions gratefully received.
Click to expand...
Click to collapse
My oh My,..
i got the same exact problem, i bought two new betteries one of them is 3150mAh
downgraded to O2 rom official, and still dies at 85%
i was thinking about getting a desktop charger. till i noticed something..
when you charge your handset it charges up 100% but the charger indicator light remains on orange. (and says charging on the soft version)
it should turn green when its full, now shouldnt it.
leaving the phone to charge till the light turns green and ignoring the software reader could charge the battery, (it would still die at 85% thought)
weird problem.. i am sure now that it is a handset problem, because both the battery and the OS (rom) were changed, and still with same results.
can anyone think of something we can try?
...
come on ppl.. think.. lols
i heva that problem to!!
hi thare i have the that problem to any way to fix it ?
I have the similar problem, except it dies at cca. 30% capacity.
As I can see there are a lot of users with this problem on this device.
I am new to this device, I've been using Wizard till now and just recently bought the Universal that is over a year old.
This battery problem really iritates me.
If ANYONE has a solution to this problem that will actually work I beg him to share it with us that are new to this device.
Well, this seems to be a problem that cannot be answered, as i mentioned before, my unit is a M5000, standard issue without any rom upgrades, new battery from from the Orange shop yet it still fails at even 95%. Gonna try a hard reset because I am sure it is a software issue, i did read somewere that the machine "thinks" it is fully charged/discharged and when you put a new battery in you need to do a re set to position the unit to basic state.
Lets see what happens.
My battery problem solved
Short time ago I suffered likewise problems with my MDA pro. After reading all the comments I decided to go for a new battery from handit. With this installed the problems even worsened, regardless which charger, or cable, or combination thereof, I used. So I swallowed my avarice and bought a new battery from T-Mobile, assured that this is the one they deliver with their phones, and now everything works fine!
It seems that there are slight differences between the batteries from diefferent manufacturers, and the pro might misinterpret the signals from the battery's electronics.
By the way - have you noticed the little red slider adjacent to the baterry with which it is fixed into the housing? If you do not put it into the 'lock' position the connection between the device and the battery becomes unreliable. It may well be that a heating-up of the battery while being charged disconnects it from its contacts!
Its a well known problem, after 9-10 months the battery cannot handle high powered functions causing it to turn off.
Get a new battery and you'll be sorted.
a 3150mah from ebay is only about £10-£15 but will make your universal a bit fatter. (they provide the larger cover for the back)
Yeh fine,,,all well an good if you do not use a jasjar car tray or holder as such, the soddin thing will not fit in it with this slug on its back
Qtek 9000 battery probs
Hi everybody
All I can say is I'm having det excact same problems with a Qtek 9000. Have tried changing batteries. Have even bought an extra extended battery (3150 mAh), and all for nothing. It worked for a brief periode. But now I'm back to square one again. The darn thing dies on me, even though the battery is charged (70-90%).
Have had a dialog with Qtek, but they claim they havn't heard of the problem before
Have been trying to figure out what the problem is..... and have tried to solve it with various workarounds.... Situation right now... Im pretty sure it's the battery on the systemboard that's causing the problems.
It kind of makes sense IMO... if you have a PC with a faulty battery nothing will work.
I'm going to see if I can get the battery changed (still have warranty). Keep your fingers crossed. I'll get back to you all if it fixes my problems.
Background:
I have had MANY PPC's (so many I can't even count them) and I've loaded many different cooked ROMS and such on most of them so I'm not a complete noob on these things (don't claim to be an expert either).
However, my most recent acquisition is an HTC Advantage bought at CompUSA. I've read most of these came with a test ROM and mine was no different except for the fact that when I attempted to update the ROM to the "official" one provided to me by HTC it would not work. I always got the error "Connection lost" about half way through the process. I tried it numerous times and it never worked. On some occasions it would get stuck on the bootloader screen but I was able to get it back to working status (still on the test ROM).
I decided to try installing step 1 of Ollipro's SPL to see if that would help loading the HTC ROM. Turns out that wouldn't work either. It would get stuck at step 1 where it would ask if "PPC gone idle and didn't work or to wait 30 seconds". Tried it many times and would try to get it to keep going but the grey box on the bottom left would say the "parameters were incorrect" and would give me the option to quit, which I would. No problem, at least my 7501 was still working.
After that I tried the official HTC ROM again and I got the same "connection lost" error I had previously, except this time I didn't get anything on my PPC screen, just a black screen, not even the battery charging light behind the joystick lights up anymore. Soft reset...........nothing. Bootloader reset....................nothing. Hard reset.......................nothing. No lights, nada. The only flicker I get is if I try a reset wheen the power cord is connected. A red light flickers behind the joystick whenever I click the reset button. Any ideas or any help?
Sounds to me like the battery is just dead. I bought one at CompUSA (had the test ROM also) and I got the red ring around the joystick too when I tried to turn it on in the store. I left it plugged in awhile and it finally booted up okay. I then replaced the test ROM with the one and only available for the X7501 on HTC USA's web site. Good luck and I hope you get it working!
I think it could be battery related as well but it had a full charge when this happened. For some reason the unit has lost communication with the battery. I'm at a loss.
I got the same problem like you man !!! but i bad luck and so stupid man , i did with HTC X7501 then it dead after that i bought the X7500 then did it again , holy "... " it dead again....man ...So how your phone now bro ????
I left out the battery a half day and tried it again but still dead. Then I left it charging overnight and tried it again but still dead.
I can't believe this. I've never had a bricked device that can't be revived but after so many have seen this post and still no solutions I'm guessing it's no hope.
I met the same situation when I started to unlock Athena ( TMobile Ameo) within not fully charged battery ( less then 70%).
Solution ( try to make BL mode) with connected wallsocket charger ( not connected to PC USB slot) or find 100% charged battery. It helped me two times.
After many tries it changed to BL mode .
Now I didn't start unlock/change ROM without 100% charged battery.
I have the same BIG Problem, only red fliker when soft reset when AC conected. I wanted to update rom from russian to english and phone stoped working (black screen), and battery heats when inserted in phone . nothing to do? i read everything but i have not got any solution. I think it may be bios dead. helap us please
Lobstrick said:
I have the same BIG Problem, only red fliker when soft reset when AC conected. I wanted to update rom from russian to english and phone stoped working (black screen), and battery heats when inserted in phone . nothing to do? i read everything but i have not got any solution. I think it may be bios dead. helap us please
Click to expand...
Click to collapse
"heating battery" (i.e. discharging when inserted, you mean?), no charge led = dead bootloader indeed.
I get the same problem. My device is work, but not charge. Also like yours i have red ring around the joystick when the battery is taked out. And if battery inside, when i make a softreset it blink one time, continued to load but not charge.
You`r speaking all wonderful. But have anybody found the solution?
Hearing these stories makes me nervous. I'm on the stock ROM (mine came from CompUSA with the latest ROM and I don't have an urge to try the cooked ROM yet). I've been using my Athena daily for 4 months, it charges correctly from several different chargers I have (car, computer USB, stock wall charger, aftermarket wall charger).
However, one day 2 weeks ago I went to make a call in the middle of the day and my Athena was dead. D-e-a-d. Usually I can make it back home at night and still have 90-100% on the battery meter, so with no use in the middle of the day and a dead battery, this was weird. It wouldn't turn on, no soft boot, took the battery out and put it back in, and always got nothing.
I bring this up here because when I plugged it in, I encountered similar problems that others here are describing. It wouldn't turn on, and it didn't give me the orange charging light behind the joystick. I ended up leaving it plugged in for a while and finally I got a red ring, not the usual orange. I've only seen red when the battery was almost dead and the unit was on. Then after some more time the ring turned orange and at this point it would turn on again. I still have no idea why my battery died so fast and hard.
So, is there a problem with the battery charging system that is starting to crop up in units that have been used a while???
miha_conan said:
I get the same problem. My device is work, but not charge. Also like yours i have red ring around the joystick when the battery is taked out. And if battery inside, when i make a softreset it blink one time, continued to load but not charge.
You`r speaking all wonderful. But have anybody found the solution?
Click to expand...
Click to collapse
Hi i am no expert but i had simaler problem no display or no lights round ring no responce to any commands (ie hard reset and bootloader ) only red light flickred on reset button all i did was removed battery while pressing reset button and placed new battery and left it on wall charger for couple of hours and before doing hard reset i pressed reset button 2 to 3 times and green light round the battery came up so i tryed bootloader and it worked and insted of flashing it with pc i just loaded the img in sd card and flashed it while whole thing was on charge (i had tmob test rom before ) which i think is best way to do no hassle of losing connection or failing in half way and it works like a charm
hope this helps
and ya if you have a spare battery it dose help
New battery?
I'm a wizard user (and lots of former PDAs) looking to buy and Athena, maybe.
Has anyone tried a new, right out of the envelope, battery? these issues sound like worn out Li-Ion batteries to me. I've had them completely conk (won't take a charge at all) if I let them go completely down, and I've had them wear out and stop taking a full charge (down to maxing out at about %20, but sometimes showing %100 depending on ROM status) when I kept charging them while they're already charged.
Li-Ion batts don't sit for long periods too well, either, so if they're sitting on the shelf at the store/warehouse, they may be suffering even more than one that has been used since earlier in its childhood.
Perhaps the answer is a switched charger that stops charging when the battery (not the ROM/unit reading) gets to %100. ???
I didn't see anything like this posted. I'm terribly curious to see if anyone can resolve it.
nother AMEO dead
http://forum.xda-developers.com/showthread.php?p=1859021#post1859021
Red ring comes for a sec only try to RESET the device with Charger connected
Click to expand...
Click to collapse
same here,
i am afraid i got a dead athena too, did you guys found any solution?? i tried switching batteries. this is my first experience with a windows mobile device not powering on, in inrepairable condition.
found another member with similar problems- http://forum.xda-developers.com/showpost.php?p=1639311&postcount=24
No genius,s on here,just insults
i have read every page on the advantage x7500,being such an old phone you would thin the genius,s on here could sort it out in seconds,but all they do is insult you.i tried to update from windows 6 on radio 1.20 to michys radio 6.5
it got to 94 percent then crashed, now when i boot up i just get a black and white screen,which then turns white,if it try to reinstall advantage 6.0 the phone reets after 2 or 3 percent..will anyboby help by giving simple term advice to unbrick it? NO.will they provide links to there advice no.THEY JUST INSULT YOU AND SAY ITS IN ONE OF THE THREADS.well im a computer tech and if anybody wants there pc or laptop fixing.guess what i will return the favour with computer speak,THAT YOU CANT UNDERSTAND
Hi all! I've got a really serious issue! My Universal turns off all the time and it can't be started if it's not connected to external power supply.
Tried two different batteries without luck. Did a hard reset and tried different roms. Additionally I tried to over-/under-clock the device to 624/416 MHz using xcpuscalar, because I thought that this app probably caused the problem, but also without any result. Cleaning the batteries contacts didn't work either.
What to do? Any idea? Is there some application for self-diagniostic out there? It doesn't turn off while it's connected to power supply or on stand by. But after some minutes of work (phone call, sms, gaming erc.) at battery mode it switches off.
I think there are some fluctuations in voltage or power!?
Help is really, really appreciated! Thanx!!
Power problems
spratelboing said:
Hi all! I've got a really serious issue! My Universal turns off all the time and it can't be started if it's not connected to external power supply.
Tried two different batteries without luck. Did a hard reset and tried different roms. Additionally I tried to over-/under-clock the device to 624/416 MHz using xcpuscalar, because I thought that this app probably caused the problem, but also without any result. Cleaning the batteries contacts didn't work either.
What to do? Any idea? Is there some application for self-diagniostic out there? It doesn't turn off while it's connected to power supply or on stand by. But after some minutes of work (phone call, sms, gaming erc.) at battery mode it switches off.
I think there are some fluctuations in voltage or power!?
Help is really, really appreciated! Thanx!!
Click to expand...
Click to collapse
Hi there,
It just sounds like typical old battery sympoms to me, I had the same problems on mine so I bought a new battery and it was problem solved.
the only thing I will say is try to get a genuine battery, not a cheaper copy or you tend to get battery level display problems. I got one of the cheap extended battery and it showed 100% till it went flat. I could be wrong of course, this is just what happened to mine.
Good luck
Jay
responderman said:
Hi there,
It just sounds like typical old battery sympoms to me, I had the same problems on mine so I bought a new battery and it was problem solved.
the only thing I will say is try to get a genuine battery, not a cheaper copy or you tend to get battery level display problems. I got one of the cheap extended battery and it showed 100% till it went flat. I could be wrong of course, this is just what happened to mine.
Good luck
Jay
Click to expand...
Click to collapse
I agree...seems like a battery problem.
Mine is going bad as well. Next week I am going to order a new one (extended of course).
Hello,
I'm sure my Hermes is not dead, I'm just having ridicious battery problems.
My battery completely drained out, I saw the screen fade out and kind of "die" as it happened. I then couldn't even charge the Hermes up, so it seems the battery just ran out of juice period. I googled around and it seemed the only way to revive the battery again is doing some complicated wiry thing with alkaline batteries.
But instead of that I just bought a new replacement battery. But it still won't charge! Does this mean my Hermes actually did die? The battery WAS extremely low so I'm certain that it was the battery. The phone can't just die like that.
Thank you so much for your help. N.B. the phone LED won't even give a red light when plugged in without battery in. I hope that's not a bad sign...
Hey there just a guess but I had a simular problem in the past and it seemed to be due to a defective camera part draining power. Only way I was able to fix it was to remove the camera part and then put it back together.
If the red LED doesn't come on when you connect to the power without the battery then your Hermes is dead, good only for parts.... If the LED does light up, connect the battery and see if it turns amber(orangey) that means its charging.
It could be the internal fuse blew. Might be replaceable but could be costly....
Yes, after reading that other people could usually still see a red LED without the battery, I gave up.
Sigh...well at least I got to see my Hermes die...the screen gradually fading away in front of me....sniff.... I will miss it dearly.
- - -
But life moves on and hey hey hey I'm the proud owner of a new Blackstone! I just wasn't ready to upgrade yet...I wanted to wait until a capacitive screened successor to the Touch HD came out...sigh
But I suppose deaths of family and friends don't happen when you're ready for them
Goodbye my Hermes
eyupwolf said:
Hey there just a guess but I had a simular problem in the past and it seemed to be due to a defective camera part draining power. Only way I was able to fix it was to remove the camera part and then put it back together.
Click to expand...
Click to collapse
Dear eyupwolf, I have similar problems.
Camera just works some times, but after that it can not be initialised again and drains my battery out. So I don't use it anyway (since 99% times tried it didn't work). If I do, I have to reset Hermes many times to set things up.
Can you describe the procedure how you fixed (removed) that problem?
Thank you,
F
battery wont charge
I got the same problems with the Hermes 200. I tired the 3 AAA battries in serial connection but it didn't help.
I even tried to cool the battery for 30 mins in the freezer (an old trick to squeeze the last little bit from the battery) the phone turned on for about 10 seconds but the os never loaded up. the phone shows red when connected to usb without a battery but led turns off when battery is insterted.
I ordered a battery on ebay, but until it arrives does anyone have any other suggestions?
thanks
Scuter
PS. It had Olipro 2.10 spl and recently installed the amazing golden globe v9 rom http://forum.xda-developers.com/showthread.php?t=458456
which is amazing.
I bought a second hand HD2, however it arrived with a third-party chinese battery. I contacted the seller who apologised and said that battery was a replacement because the original didn't hold a good charge, and he would send the original through the post. The battery however was fully charged so I flashed all the neccessary files and installed NAND Android (my reason for buying it in the first place), however today - the same day it arrived - I noticed that the orange charge light was going off, usually when the phone screen went off. This necessitated plugging the USB lead back in again, and within sometimes less than a minute the same problem would occur. I have checked the battery prongs, reset the the phone, changed USB settings etc and the problem persists.
Just wondered of I should be worried...I am unable to find an identical problem to this on the forums so I'm assuming it's not a ROM issue. I am currently using the Desire port from DFT.
Would a cheap Chinese battery demonstrate this sort of problem?
The seller says he never had an issue of charging the phone.
My next resort is to flash Windows Mobile back on, but I'm at work and a bit anxious so was hoping for someone with some experience to reassure me!
All USB syncing etc works fine...it is literally just charging that's the issue.
Maybe it's your USB that's faulty. I had a faulty usb that would go on and off sometimes too. However I don't see why the battery would affect the LED light, as the battery has to be connected to the phone for it to stay on, and so the battery can't be losing it's connection with the phone randomly, so it's either your usb cord, or the port.
Word of advice, don't let your phone lose power cuz of the faulty charging. I assume you know that MAGLDR doesn't let you charge the phone while off, so a dead battery in our case, is a dead phone. Happened to me once cuz of my usb, luckily there was still a small amount of charge left after i took the battery out and placed it back in.
It's definitely not the cable as I've used an official HTC charger with it which does exactly the same thing. I've also tried with a Samsung MicroUSB charger from my Galaxy S
Maybe it's the usb port then... That's the worst case scenario because you'd have to get the whole motherboard replaced...
However if in winmo you don't experience the problems, then it was just some software problems, so try a different radio and build, and see if they work.
Edit:
Or maybe it's the LED that's faulty. (never heard of such a situation but anything is possible) >.>
Does it still charge even if the LED is not orange/on?
Thing is though I can pretty much get it to stay charging if I don't let it lock and the screen go off? Could this still be a problem with the USB port? I'm getting worried now as I don't like the hassle of sending things back through eBay. I'm wondering if the seller bought a spare battery thinking it was just a battery problem and isn't telling the whole story. Foolishly I didn't test the device with Windows Mobile, I just went straight into flashing as I had put Android on my friend's HD2 the other day in exactly the same way...his is even an ex Virgin Mobile phone like this one. Needless to say, he is having no charging issues.
Dude dont worry , the problem is the battery ! i got two chinese battery ones and both cant charge with the phone, i have to use eksternal charger Dont worry the red and orange led flashes constantly when i try to charge it
Just buy a cheap charger from ebay , and buy a oem htc hd2 battery
Hi thanks for your reply. Mine doesn't flash red and orange though: the orange light comes on as normal and the phone reports it as charging, but after a while (seems to be when the phone goes to standby most of the time) the orange light turns off and the charging symbol disappears. If I unplug and replug again the light comes back on for a period. I've not tested thoroughly but I THINK it will stay charging when I leave the phone out of standby with the screen set to stay on for 30 minutes. I really HOPE it's a battery issue but it sounds slightly different to yours as mine does at least charge to a degree. I'm worried there's a blown capacitor somewhere on the logic board that's making the phone charge malfunction but obviously there's no way of testing until I get a new battery.
It concerns me that the seller said he had no charging problems...he must have been able to charge it somehow as the battery was full when it arrived...could I have burnt something out when flashing?!
Mine do charge to about 50 % and then it stops
Im 100 % sure its the battery becouse the battery has a circuitboard inside of it, and thats often messed up considering its made cheap in china . But test it with your friends hd2 original battery You can 2 see if the wet indicatior has been activated
the " white " paper next to the battery poles should be white and not pink, alltso where the skrewholes of the phone that should allso be white just to make sure your phone is not waterdamaget
I don't think flashing could have burnt something out. Overclocking and generating a lot of heat can burn something out though.
Didn't you receive the stock battery? Why not try it with that, and if the problem stilll persists then it might not be the battery. Either way, it will help you to test out the phone with a stock battery.
I tried it again after a few hours and it charged for a fair while before the light went off again.
I don't have the original battery as the seller has yet to mail it to me.
Does anyone else think it's worth me trying out a stock Windows Mobile ROM to see if it works? Might be that Android ROMs are less forgiving of cheap batteries with dodgy circuitry..
UPDATE
Ok so I've flashed Windows Mobile onto the device and wiped Magldr. The phone now alternates between a green and an amber light on the charging indicator. Looks like Windows Mobile won't charge it at all!
Does anyone know what this means?
I've checked for water damage in the areas mentioned and there is no sign.
Well your best bet is to send it in for repairs. But I'd suggest you test the phone out first with a stock battery.
Well I Only bought the phone yesterday so I certainly won't be paying for any repairs.
Got a replacement battery today - a genuine HTC one.
Plugged in, switched on....flashing between amber and green
I have a nagging suspicion this is going to be an eBay refund nightmare.
have you checked that the pins on the phone is not bendt? pins where battery poles connect to phone
problem solved? fingers crossed
OK so as a last resort I flashed radio 2.15 to the device. Seems that this has completely fixed the problem as without even restoring the phone is now charging properly. It seems that a corrupted radio flash had affected the charge somehow....at least I hope so.
The same problem has not come back again today at all.
Might be worth throwing this solution in a problems and solutions section as I haven't found any reference to it on the net and it might fix things for others panicking over their handsets.
That's nice.
Good for you, since it's a hassle to deal with sending back the device and shizz like that.
was just searching is anyone had a similar problem like me. to the OP yours sounds like my problem.
Had these fake OEM batteries for a while now. Until recently they have been charging ang turning off in 1 1/2 minutes. put a genuine OEM battery in and the problem is gone.
My solution was OEM can charge thru phone but fakes cant, use fakes as backup and charge it thru a desktop charger. goodluck