Hello,
the buttons beside the screen don't work after a shock
someone has an idea?
please help
They are connected with the tape. They could get disconnected, however the best thing is to open the phone and check it by yourself. It shouldn't take more than 15 minutes to completety dissasemble the phone.
Related
I have a blank screen on my jasjar. the screen was turned in the wrong direction and flex cable got damaged. I opened the device and found that one wire which connects the motherboard and the screen was cut. I connected it back but the screen is still blank. backlight and touchscreen are working, the device can load and receive a phone call.
I searched the net and found that many people have or had the same problem, however I couldn't find any answer or useful info.
if someone know what might be wrong with my jasjar, please help.
Hi guys,
I got given another magician and after some troubleshooting and pluging the m/b into my screen i got it to work. (the screen was faulty)
BUT, then i plugged the screen back into my original JAM and put it all back together and all i get is a white screen and then a little while later i hear the sound that you get once you perform a hard reset.
What i want to know is if it is the connection to the screen or if i have some way screwed my m/b
ATM, i am using my given m/b to use as my pda so i can make calls.
Just to clear things up this is what happened:
1. Recieved jam from friend in post (we will call it j2)
2. dismantled both my jam (j1) and j2 and plugged j2's m/b into j1's screen and all go
3. tested it the other way round and found that j2's screen was stuffed
4. put j1 all back together and now all i am getting is a white screen followed by the windows mobile set up tone
5. straight to xda-developers for help
Any help GREATLY appreciated
Hello,
I have the JasJam with WM6 and radio 1.48
I have a problem with the camera. Sometimes it works great and other times when I start it, it shows green and pinkish flickering .. can't see a thing!
It seems like a displaced cable or something.. why? because when I hit the device with my hand, it goes back to normal!
If anybody has hardware experience with this thing, can you please guide me through fixing it?
Another thing is the reception... reception is always good and I can't complain.. but sometimes when I'm in the middle of a call, the line cuts! (this is happening with almost 80%) of the calls.
What's worse is that when it happens, I can't get to hang up! the red button won't work... "End Call" won't work... the counter just keeps counting seconds until about a minute when it resets the reception (it loses the network, looks for it, and becomes fine again when it finds it)...
I bought this device for a lot of cash, but it caused me a lot of trouble... it's a Saint when it works... but real Satan when it doesn't...
I would appreciate any help you guys can provide.
Thank you.
Hey i have the same problem as you on my "Dopod 838 Pro"
My camera flickers at the worst momments when i want to take a picture of something. i need help with it.
and another problem about my phone is all the buttons next to the screen (green button,end button, ok, button 5, message, internet explorer.. ).
and when im really mad i hit the pda and then the buttons start working for about 10 seconds..
i really need help with these two problems please help.. anyone..
I just dropped my qtek S200. When I turn it on noe, I just see colored stripes, but the qtek seems to work normal, because if I use the camera button you can hear the "click" sound e.t.c.
What shall I do know? Please help me - I am quite in Panic know .-(
Please anyone?
Did the display cable come loose? You'll have to open the unit in order to rectify this. As I have just ordered a new case, I have searched for instructions how to do this and found
this step by step manual.
Good luck
Robert
Thank you very much for your help - I will try this out. I hope I can open it, because I am not very good in this.
How does the display cable look like?
I got stucked at this step: NOW CAREFULLY LIFT THE BACK COVER AWAY FROM THE FRONT AND NOTE THE SHORT SPEAKER CABLE, USE YOU TWEASERS TO CAREFULLY DISCONNECT IT
How do I disconnect it??
What exactly does the device do? Does it respond to charging? Does the screen have any response to being switched on?
The qtek works properly - that means I can use the com button and touch the screen where eg the bluetooth used to be and I can turn it on.
The camera button works too, because you can hear the click when taking a photo.
The only thing is, that you can only see vertical colored stripes on the screen that change their color after some minutes.
I just opened it now, but it did not help.
you have to buy a new one hahahaha
I have X1 for 5 day now and seem to have no problem with it. However, today I noticed that if I turn the phone upside down (for example, you hold your phone while you in bed.) and touch the middle button (the joystick) it seem to loose a little when I touched
It's normal? Please confirm me cause I'm still in 1 week return if I found problem.
Thank you in advence.
My optical mouse/button is loose too. If I shake the phone it rattles. I would send it back, but I think I'll wait until supplies stabilize...lol.
Thank you very much for confirm it, However it happen to everyone's phone? or just a few case?
if Anyone have "optical mouse/button" stay fit and not loose. Please confirm us too
No problem on mine. My X1 is 08W45.
desman, you man your button is fit not loose?
Yes, I put it upside down and don't feel any loose.
Thank you desman, I think tomorrow I will have to go to Service center to change it.