BlackBerry Connect on Toshiba G900 (WM6 Pro 3.07ROM) - Windows Mobile Development and Hacking General

Hello,
Is it possible to run BlackBerry Connect 4 on Toshiba G900 with WM6, ROM 3.07? If yes, what tricks and reg mods should I apply?
I'm struggling 2 days now trying almost everything and I always get "PIN: Pending", which means that I'm unable to register the device on BES/BIS.
Any ideas?
Thanks,
SH.

Related

Using SX56 to connect to laptop to connect to gprs

Can anyone tell me how to use the GPRS on a SX56 as a wireless enabler for a laptop via InfraRed?
Thanks
IR Modem
You can find your answer (and much more) here:
http://www.myxda.com/XdaII/serviceandsupport/template/XdaIIHowToUse.vm
I was able to connect my T68i as a bluetooth GpRs modem to my tablet PC with a Anycom bluetooth card without any problems.
Using the same tablet I am able to bond the XDA II and ActiveSync using bluetooth.
I have figured out that I would have to create a Bluetooth modem on my tablet PC and then create a GpRs connection with the dial up number for t mobile GpRs in USA.
The problem is that in control panel of the tablet under modems if I try to create a new modem as the XDA II I would need software which I do not have.
Under modems in my tablet PC I only see:
Direct connection
T68i on COM 9
Can anyone help?
smcfeetors said:
Can anyone tell me how to use the GPRS on a SX56 as a wireless enabler for a laptop via InfraRed?
Thanks
Click to expand...
Click to collapse
Unfortunately the other reply to this thread applies to the XDAII, whilst you have an "XDA I"... As has been discussed in other threads, the Windows Modem capability is part of some version 3 based ROMs, including the XDA Dev "Special Edition" but has not been a part of any version 4 based (WindowsMobile 2003) ROMs until this recent development of the German 4.00.33 ROM.
Are you using 2003/ROM 4.00.xx? If so, your choices are to downgrade to a vers. 3 ROM from a kitchen, or to wait until someone smarter than me figures out how to get the German Modem firmware into an English ROM.

I need help restoring my windows mobile 2003 software

:roll:
Hi I have a big problem and i need all the help i can get
I have an XDA IIi but i accidently deleted all the data on it
the opertating system is gone the screen is only showing me Serial 1.0
and when i connect to my pc only shows USB 2.0
I would like to know if somebody can help me out with this and tell me how to restore the software to my device, i have a backup copy on my SD card, but i don't know how to used
Please help me
thanks
[/b]
have to reflash it
how did it happen?
did you try puting any rom version in it or what?
more info is needed
hey
I was trying to upgrade the radio version of the phone, but the version i was installing was not desgined for the XDAIIi , so, instead of upgrading, it deleted of the rom of the device and now the operating system is gone
the only thing i still have is the backup copy that i made defore the upgrade
i don't know if there is a way to use that backup copy in order to restore the system
thanks
Recommendation
It is propably that the system ROM was erased during upgrade and the upgrade wasn't successfull. Try to download the Diamond 1.2 WM2003se(my recommendation) ROM images package(somewhere available at this forums(Himalaya Upgrade)) and aferwards to flash your device with these files. If u want,u can try also the WM05 system.
He said his device is an Xda IIi not the old II.. Well you can reinstall back ur old ROM, no worries.. Download from my-xda.com..
i or not i
I thing there's no matter if is it IIi or simple II. Or not?
How do I fash my device in order to install diamond 1.2?
I also was looking an upgrade for the XDA IIi but now there are not offering any updates, I have tried to install the upgrades for the XDAII but it gives me an errror telling me that the ROM version is different and it cannot be installed
...
If you mean the Country ID Error while attempting to flash the WM05 system,there's a problem of this OS. 2003se is without problem(for me). Simply download the Diamond ROM from this topic:
http://forum.xda-developers.com/viewtopic.php?t=18287
or directly:
http://forum.xda-developers.com/download.php?id=3739
This contains 4 files(maybe more,but these are important).
-HimaUpgradeUt.exe
-ms_.nbf (Extended ROM image)
-nk.nbf (System Image)
-Radio_.nbf (Radio stack)
Start the bootloader(probably you are there),put the Hima to cradle,Windows at your computer detects your device and then extract the downloaded file into one folder and run HimaUpgradeUt.exe
This utility is writing what you should do.
As I have readed that the WM05 OS is a little bit buggy(some compatibility problems etc..) at this time to use in Hima. Therefore I am using the 2003se.
Thanks a lot!
Hey guys,
I just downloaded the XDA IIi ROM version from the O2 website
My device is back to normal. I coudn't do it without all of you guys.
Thanks a lot specially to you jamil_mhmd for providing me the address
Sincerely
Jorge :wink:
You're welcome
Nice to help you.
Re: i or not i
TomasNM said:
I thing there's no matter if is it IIi or simple II. Or not?
Click to expand...
Click to collapse
Of course it does matter.. Remember that the II and IIi is now a really different device even though both looks identical.. For example, u said he can upgrade to WM2005 (or ROMs that was meant only for Xda II), but of course this can't be done, this is bcos the difference in hardware specs, 4 example IIi has 1.3 MP cam (II = 0.3MP), 128MB RAM, 128MB ROM (II=128MB RAM, 64MB ROM) and so on..
JorgeGZC, I'm glad to be of help to you.. :wink:
Oh sorry.
I didn't know. I'll be well advised.
İ am a mda2 user. İve bought my device from Germany and after that i changed its ROM to an english one using a rom editor to change its country id .. This encouredged a close friend of mine and he bought a O2 XDA2i. And since both me and my friend have no idea about German language we immediately tried to convert it to an english ROM.
And using a wrong ROM (sinmerged 2003 se for himalaya) i killed his machine. It now only writes serial or usb (when connected to cradle). Someone told us that if we flash it with a original German ROM it can work again. But there is no German ROM downloadable . And even if we find a German Rom and install it , it wont solve our language problem. I am a dentist and i even cannot believe how much i've learned browsing these forums
If you can help me i will be very happy!
note : in the ftp server there is rom named german rom for xda2i.. But its a lie. its in english
The same?
That looks like the same problem as at the top of this topic. Just read all this posts once again and you'll get the right way to solve your problem. Hope that helps.
I also have the same problem. I tried to install the wrong upgrade. I've downloaded the new one but i keep getting a connection problem message because activesync can't find the XDA. Help please!!!!
...
When you are in bootloader then ActiveSync will not find the device to synchronise with(cause the WMOS is not running and therefore is any synchronisation disabled). When you put into the cradle,the computer should find new device(Microsoft USB Sync). Then is the device connected and ready to update.

enable bluetooth modem + activesync via bluetooth?

I have been searching this forum and couldn't really find a definite answer for this, so I apologize if this is a repeat question.
I have Cingular 8125 that has been unlocked and flashed with xelencin's T-mobile 2.17 ROM. I have been trying to use the device as bluetooh modem and also activesync via bluetooth, but unable to do so. I have tried for hours and this has been a very frustrating experience!
Could somebody help me with a step-by-step guide on how to get this thing to work? I am using Windows XP Pro with service pack 2, ActiveSync 4.1, and widcomm 3.0.1.913
Thanks in advance for your help!

destinator 7 fails when sim is installed on HD2

Hi guys,
I 'm facing a very weird problem. I own a HTC HD2. I have installed Destinator 7. When the SIM card is not installed (or the SIM is physically installed but I don't provide the PIN) destinator works fine. When I enter the PIN for the SIM, so my phone connects to the mobile phone provider, Destinator software fails to start. The destinator's logo appears on the screen and HTC halts. Power-off button doesn't work and I had to press the hard reset (red pin at the back). I have ran many tests and the conclusion is always the same - Destinator halts when SIM is installed. Does anybody else had a similar behavior? Any ideas for further troubleshooting are welcome.
thanx.
I have both destinator 7 and igo8 on my hd2 and both work without any problems, do you have a branded hd2?
Hi Mathie,
thank you for your reply. My HTC is not branded or somehow locked (I hope). I 'm running the original ROM v. 1.66.482.1 ELL, O/S 5.2.21869, manila 2.5.19211619.0, RF 2.06.51.07. My service provider is Cosmote. I 'm not sure if this information helps, but I cannot think ANY reason why destinator hangs when the telephone SIM is installed.
Is there any possibility the GPS receiver to get a conflict with A-GPS ? I' d rather say no...
N-drive at the other hand, works fine, it's an excellent program, but I 'm get used to Destinator.
memoryic said:
Hi Mathie,
thank you for your reply. My HTC is not branded or somehow locked (I hope). I 'm running the original ROM v. 1.66.482.1 ELL, O/S 5.2.21869, manila 2.5.19211619.0, RF 2.06.51.07. My service provider is Cosmote. I 'm not sure if this information helps, but I cannot think ANY reason why destinator hangs when the telephone SIM is installed.
Is there any possibility the GPS receiver to get a conflict with A-GPS ? I' d rather say no...
N-drive at the other hand, works fine, it's an excellent program, but I 'm get used to Destinator.
Click to expand...
Click to collapse
have you tried to put another sim card in your phone? wind, or vodafone? and see if the problem insists? have you tried to update quick gps? have you changed the com ports? (by default destinator 7 uses com port 4)
Hello again.
I have tried to perform the following tests.
1) I have replaced cosmote SIM with Vodafon one. I destinator has the same behavior.
2) I turned off RF radio (airplane mode). Destinator works fine but of course I cannot use HTC as a mobile phone.
3) I have formated the entire flash (CF) and create only the destinator directory. The problem persists.
4) I 'm not sure if quick GPS interacts with Destinator, but since you 've mentioned it I run quickGPS version 1.3 (built 1920.2423)
Destinator has been set up to use com4. If I don't register to a Mobile Provider (or RF is dissabled) the program runs fine, otherwise the startup logo fills 9 out of the 10 red arrows and stacks there.
thanks once more for your time.
where did you buy your phone? are you using a stock rom or a cooked one? I am using this rom here and all is well,no problems at all if the problem persists download the above rom and flash your phone with it. i'm sorry but some things get messed up if your rom is not well installed i can't help any more.
Hi again,
thanks for your answer. I 've checked the rom link you 've mentioned. I 'm already running ROM v. 1.66.482.1 ELL. I got the HTC from a recent offer of Vodafon. They sponsor a 450 Euros discount for the device, and HTC HD2 was in the list. I have not flashed the phone yet, since I already have the latest release. I 'll get a full backup and I 'll try to flash it, just to see if that will fix the problem. I 'll post my findings.
thanks.
Hello,
I have good news. I have re-installed the original ROM v. 1.66.482.1 ELL as you have suggested and Destinator 7 works FINE. I still cannot figure out what could of being wrong, with my original same version ROM, but when I re-flashed to the one downloaded from here http://www.htc.com/gr/SupportDownload.aspx?p_id=297&cat=2&dl_id=863 the problem is gone.
Thanks once again for your valuable suggestions.
memoryic said:
Hello,
I have good news. I have re-installed the original ROM v. 1.66.482.1 ELL as you have suggested and Destinator 7 works FINE. I still cannot figure out what could of being wrong, with my original same version ROM, but when I re-flashed to the one downloaded from here http://www.htc.com/gr/SupportDownload.aspx?p_id=297&cat=2&dl_id=863 the problem is gone.
Thanks once again for your valuable suggestions.
Click to expand...
Click to collapse
glad I could help, feel free to contact me again, να εισαι παντα καλα!

[Q] Help please !! I crashed my Mda Pro

Hi all,
sorry about my english.
On my Mda i would installed the sd-version of android .
Before this, i update my radio rom from 1.17 to 1.18.
But during the update/ installation i become an error.
Since that, my Mda show me the bootloader (serial/usb).
No chance, to run the "exit-bootloader" file, because the usb-connection is killed.
I have deinstalled and installed the windows mobile devicemanager, but nothing happend.
My last chance, to activated the hardreset had no function.
A call to HTC linked me to xda-developers.com
So, can someone help me, please ?
Thanx
Schuschi,
Try the advice I posted here. Don't forget, to follow my advice you need to ensure Activesync or Mobile Device centre is configured to NOT connect via USB.
http://forum.xda-developers.com/showpost.php?p=20726654&postcount=5
Regards
Phil
Hi Phil,
thanx for your reply.
My OS is 7 and i've tried your post. On the screen of my MDA i see "USB".
I've deselect "connect via USB" in Windows mobile device centre...the driver for Win 7 was updated.
The problem: there's no usb- option in mtty , which i can select...only com1 and com2.
So i try another cable and test it again.
Regards
Schuschi
I don't think it will be the cable. I had problems using Win 7 and went back to my old XP laptop. Do you have another system you can use or can you load a virtual XP machine? I have never successfully used mtty on a Win 7 machine - sorry!
no prob...
yes, i've a XP on a bootable stick, which i test it now.
I'll let you know about the results.
Thanx so much for the moment.
PS: Did you have experience about android (emulator) on a mda pro ?
Schuschi said:
Did you have experience about android (emulator) on a mda pro ?
Click to expand...
Click to collapse
Yes I did but it was very slow and my XDA Exec vibrated lots and LOTS but I think that is just how the Android build sets itself up on the HTC Universal. I tried it twice and got the same results so went back to VNInt's build of Win 6.1
http://forum.xda-developers.com/showthread.php?t=458296&highlight=vnint
and Homescreen PlusPlus with the clock theme
http://www.chi-tai.info/cs_batterystatus_xda_neo_wm5_im_cs.htm
Hi Phil,
my Mda is alived...it was the "wrong" OS.
No probs with XP.
Thank you so much
Glad you got it sorted, what ROM are you now running?
Now i'm using Tomal V12 WM6.5 build 23089, but i'm looking around to find a "better" rom.
The reason to update my rom was the app "Whatsup", which runs on Androids...
As solved, closed

Categories

Resources