Related
Ok so my Cingular 8525 is basically unusable due to the touchscreen thinking it's getting taps in the upper right corner (upper left in landscape mode). This has the nice effect of closing programs down to the today screen in portrait mode or constantly popping up the start menu in landscape mode (about three times a second). Any ideas?
I tried soft resetting and also removing the battery for several minutes. Haven't tried a hard reset as I don't want to go through that except for a last resort. Tried wiping the screen with a soft cloth. There are no weird programs on the device except what everyone here uses.
I still have 5 days before the end of my 30 days return period with Cingular. If I bring it back will they just give me another one?
aroundlsu said:
Ok so my Cingular 8525 is basically unusable due to the touchscreen thinking it's getting taps in the upper right corner (upper left in landscape mode). This has the nice effect of closing programs down to the today screen in portrait mode or constantly popping up the start menu in landscape mode (about three times a second). Any ideas?
I tried soft resetting and also removing the battery for several minutes. Haven't tried a hard reset as I don't want to go through that except for a last resort. Tried wiping the screen with a soft cloth. There are no weird programs on the device except what everyone here uses.
I still have 5 days before the end of my 30 days return period with Cingular. If I bring it back will they just give me another one?
Click to expand...
Click to collapse
on your touchscreen problem.. i have seen this occur by someone improperly putting on a screen protector or maybe there is some dirt up there.. and if you take it back to the store they may give you a new one or make you call the warranty by mail line and get a replacement that way
..... or your OK button could be stuck down
I took a bottle of lens cleaner from my camera bag and thoroughly cleaned the screen. I ran my fingernails under the edge of the screen and really made sure no dirt was under there. Lo and behold, it seems to be working fine now. I browsed some RSS headlines for about 10 minutes with no problems.
Weird though, I have used an Ipaq 4705 WM5 pocket pc for two years now and really ran it through the ringer. It looks like it's been to war and back (which it has in a since) and never experienced errant screen taps. Oh well, still enjoying the 8525 (last phone was 2125).
Thanks so much!
kevino said:
..... or your OK button could be stuck down
Click to expand...
Click to collapse
good point, i had that problem once also, forgot all about it
aroundlsu said:
I took a bottle of lens cleaner from my camera bag and thoroughly cleaned the screen. I ran my fingernails under the edge of the screen and really made sure no dirt was under there. Lo and behold, it seems to be working fine now. I browsed some RSS headlines for about 10 minutes with no problems.
Weird though, I have used an Ipaq 4705 WM5 pocket pc for two years now and really ran it through the ringer. It looks like it's been to war and back (which it has in a since) and never experienced errant screen taps. Oh well, still enjoying the 8525 (last phone was 2125).
Thanks so much!
Click to expand...
Click to collapse
Just a note of caution!!! This is related to the screen alignment issue i.e. the touch sensitive area of the screen continuing beneath the bezel and causing unwanted touches whether through dust or the sticky gasket in there.
May not return, or will be cured again by the "business card" fix / or as you did a firm clean to release the screen from touching the bezel.
But, it's a question for you, if you only have 5 days left under warranty. Most people with the SA problem find the first signs appear in the first couple of weeks. I would certainly put it through it's paces, open up a few applications leave wifi on so it heats up, surf web over wifi etc etc as the added bit of heat generated internally was a known factor in exacerbating the problem. If all stays well over next couple of days maybe it'll be OK.
Would be good to get urgent feedback from anyone with a newer Hermes who's had this issue and what happened.
Mike
Argh, it's back. OK, I'm certain it's a touchscreen problem and not a button sticking as holding down OK will not cause the start menu to pop up while an application is up and holding the windows key will not close an app. Also the problem is delayed if I hold the stylus down on the screen. It's just the upper right (portrait mode) of the screen that is getting the errant screen tap (about three or four times a second).
I've ran a business card through the edges and it doesn't help. I'm not going to take this thing apart. I did that several times with the 2125 to fix unresponsive keys and joystick but the problems always reappear. My one year old 2125 is barely functional now. My g/f would rather keep her crap LG flip phone then inhieret the 2125 after watching me battle it. That's pretty sad.
I'm going to try a hard reset (second one in three weeks) and if that doesn't help I'm returning it to Cingular and getting my money back. Then I'll either buy another one or a blackjack. I like the 3g and love this device. It's my third Windows Mobile 5.0 product. I don't like the sub-par build quality on my second HTC product now. I paid $599 plus tax for this phone at a local Cingular store (despite the web store saying $550).
My advice for what it's worth is take it back. This screen business has a habit of coming and going and it's entirely possible you hard reset and everything is fine and two weeks later it's back. Also would be better to return with the issue present (not that they wouldn't believe you -would they?)
On the whole though this problem is much more rare than it was, so if you do get the same device again hopefully you will be luckier. If you get directly from shop though check the firmness of the key board clicking into place that seems to still be fairly common problem.
Not the best start to the new year!!
Mike
Well I got desperate and hard reset... I could barely get past the screen alignment startup so needless to say that didn't fix things. Having gone this far and thoroughly pissed at having to reinstall everything I decided to loosen those screws on the back and run a card around the edges.
So far, it's working! I'm not content settling on this hack though so I'm bringing it back Tuesday and will update on my experience at the retail store (not looking forward to that).
Happy new year and thanks for all the super fast responses guys!
Alignment
I was browsing the www the other day and saw a korean/ japanese site showing the inside of these precious devices, and (as pointed out above) how the seal/ gasket underneath the bezel is the root cause of our anguish.
There were some detailed pics of how you can DIY, and remove the gasket, but it's no where near me basic level of competency.
Why would they design a touch-screen to big for the device I wonder???
there is also the business card trick about sliding it underneath the edges to loosen the gasket... there is a whole thread on this screen alignment issue
what site shows how to fix the gasket?
There is a post about someone seeing a site showing how to fix the gasket proplem on the touch screen. Could I please get the URL??
johniz1967 said:
There is a post about someone seeing a site showing how to fix the gasket proplem on the touch screen. Could I please get the URL??
Click to expand...
Click to collapse
Look down this page. Keep in mind non of the theoretical solutions is guaranteed/
http://wiki.xda-developers.com/index.php?pagename=Hermes_Problems
Mike
Just got back in from my local Cingular store and actually had a pleasant, hassle-free experience exchanging my 8525 for a brand new one. I explained to the CSR the issue and she immediately understood the problem (must not be the first guy walking in there about this).
Unfortunately, she didn't have any in stock but merrily called around and found six others in stock at nearby stores. So off I went to the next store and had the old 8525 exchanged for a new one in less then ten minutes. The CSR didn't even bother to look at the old phone or check the accessories I returned with it.
The new 8525 is syncing up as I write this and immediately I notice some things are different. First of all, written on the side of the box is 12/26. So we know this phone is probably brand new. The keyboard does indeed click in and out more firmly then my old one. The USB cable plugs in tighter (a good thing, I was always getting USB connection problems), and lo and behold Windows Vista installed HTC sync drivers then Media Player automatically recognized the device (never did any of that on the old one).
I'm using the Windows Mobile Device Center Beta on Vista RTM and it just finished syncing without any problems. Moral of this story is if your 8525 is experiencing any problems at all and you are within 30 days, return it for a hassle free refund.
Good news and you're absolutely right about getting it back within warranty if there's a fault.
Great stuff!
Mike
aroundlsu said:
Just got back in from my local Cingular store and actually had a pleasant, hassle-free experience exchanging my 8525 for a brand new one. I explained to the CSR the issue and she immediately understood the problem (must not be the first guy walking in there about this).
Unfortunately, she didn't have any in stock but merrily called around and found six others in stock at nearby stores. So off I went to the next store and had the old 8525 exchanged for a new one in less then ten minutes. The CSR didn't even bother to look at the old phone or check the accessories I returned with it.
The new 8525 is syncing up as I write this and immediately I notice some things are different. First of all, written on the side of the box is 12/26. So we know this phone is probably brand new. The keyboard does indeed click in and out more firmly then my old one. The USB cable plugs in tighter (a good thing, I was always getting USB connection problems), and lo and behold Windows Vista installed HTC sync drivers then Media Player automatically recognized the device (never did any of that on the old one).
I'm using the Windows Mobile Device Center Beta on Vista RTM and it just finished syncing without any problems. Moral of this story is if your 8525 is experiencing any problems at all and you are within 30 days, return it for a hassle free refund.
Click to expand...
Click to collapse
since your appears to be new from 12/26.. i am curious what firmware is on that phone.. details please
Cingular 8525 touch screen no working
I am having a problem with the touch screen on my 8525. My phone was working fine then the then the screen stopped responding. I was able to navigate via keyboard but that was it. I did a soft reset and it did not help. I then did a hard reset and the screen went to the setup and wants to align the screen which obviously I cannot do.
The changes I have made the same day prior to it not working are as follows:
-Unlocked with Hermes SIM Unlock
-Installed latest Cingular ROM
-Installed fit4cat Hermes Tweaker v1.1a
The phone worked fine for about 12 hrs before the touch screen stopped working.
Any suggestions?
Hey there, I have had the problem before (about 3.5 weeks ago). I had to send it in for service (since I am not a Cingular customer anymore but use the 8525 with T-mobile).Good luck.
wedgesurfer said:
I am having a problem with the touch screen on my 8525. My phone was working fine then the then the screen stopped responding. I was able to navigate via keyboard but that was it. I did a soft reset and it did not help. I then did a hard reset and the screen went to the setup and wants to align the screen which obviously I cannot do.
The changes I have made the same day prior to it not working are as follows:
-Unlocked with Hermes SIM Unlock
-Installed latest Cingular ROM
-Installed fit4cat Hermes Tweaker v1.1a
The phone worked fine for about 12 hrs before the touch screen stopped working.
Any suggestions?
Click to expand...
Click to collapse
I need a replacement windows PDA phone for my lost wizard... and i have a friend willing to sell his 8525 for $50... the downside...
according to his is... his touch screen works half the time.... something about working on a full charge... or not working on a full charge... and when its halfway charged... it does the opposite... etc etc...
he said the screen lights up just does not respond to the touches under the above mentioned conditions.
i did a search over here and HOFO.... and have noticed alot of people have problems with the top right corner of the screen (portrait) being stuck and closing out apps.... or launching the start menu repetedly...
and there isnt really a fix?....
is 50$ still a good deal?.... will a replacement screen and digitizer fix it?.... which is around another $50 i believe?
or should i buy one from ebay... they are selling for around 170-200$ shipped.... or is this a problem that plagues all 8525 hermes eventually?.. and i shouldnt bother with this model... and go back to the wizard or get something else?
The Hermes is a really great phone (I passed on getting a Kaiser, as it didn't offer enough of an upgrade), but I don't know if I would personally buy one in that's having issues like that.
50 bucks isn't bad, though. I might bite for that price.
I've had no screen issues over the last 1 1/2 years. I just saw a used 8525 sell for $181 on ebay...it's a great scalable device!
Alright.. i got a hold of the phone.....
everything seems great.... touchscreen was working... but as soon as i went to charge the battery.... and took it off charge once it was filled up to 80%, the touch screen stopped responding...
and i also did a hard reset ... and the screen still isnt responding.... and i cant pass green setup screen that asks me to tap the screen to continue.
any way to bypass this screen?... i dont mind using the phone with only the buttons...
and do you think this is battery related?.... the prev. owner said something about... leaving the battery to cool over night... and pop it back in... and touchscreen should respond again....
any suggestions?... thank you.
Find the program "Remote Screen Alignment". If you can get the Hermes to screen alignment to work, you can save the settings to your pc then if you reflash an os or have to hard reset you don't need the touchscreen. Try taking the battery out overnight and see if you can do the alignment then. Once past the screen alignment you can operate the Hermes using the buttons BUT you need to first get past the alignment settings.
Alternatively, if you know someone with the same Hermes you can get the Alignment settings off their phone. You need the above app.
Cheers...
if your looking for a screen, i have a screen complete with digitiser for sale? PERFECTLY working
i can also throw in a ribbon cable which works but only displays colours in 4bit mode!
PM me if you want the screen
ultramag69 said:
Find the program "Remote Screen Alignment". If you can get the Hermes to screen alignment to work, you can save the settings to your pc then if you reflash an os or have to hard reset you don't need the touchscreen. Try taking the battery out overnight and see if you can do the alignment then. Once past the screen alignment you can operate the Hermes using the buttons BUT you need to first get past the alignment settings.
Alternatively, if you know someone with the same Hermes you can get the Alignment settings off their phone. You need the above app.
Cheers...
Click to expand...
Click to collapse
well its not even the screen alignment screen that im stuck at....
when you do a hardboot.... the FIRST splash screen that shows up after the ATT stuff
its a green screen that says windows mobile DIRECT PUSH... and it says
"please tap the screen to continue etc etc"
will that program help me get past that?....
and the battery is out of the case right now... and im in school..., hopefully by the time i get back home it should work.
duke_stix said:
if your looking for a screen, i have a screen complete with digitiser for sale? PERFECTLY working
i can also throw in a ribbon cable which works but only displays colours in 4bit mode!
PM me if you want the screen
Click to expand...
Click to collapse
well... i see that you live in the UK... it might not be favorable purchasing it from you...
and tihs ribbon cable that you speak of.... do i need one for the isntalation of the screen?... and the one you have isnt made for this phone right?
Alright guys... so pretty much what the previous owner says checks out..
the phones touchscreen started responding to touches on a cold battery that was sitting for a few hours....
as soon as i begin to charge and the batter warms up... or the phone warms up.. im not sure... the touchpad stops responding.
ANY SUGGESTIONS?...
is this an issue with the battery or the touchscreen?...
aside from that.... this phone is fantastic!
Hi there
I am in the UK, and the screen has in fact been removed from a cingular 8525 i cannabilised for the d-pad board, the screen works perfectly and the ribbon cable will of course fit your phone.
I am willing to ship to the USA, and in fact i regularly do, only recently i just sold a little rubber dust cap for the hermes on these forums and its on his way to him right now. if you can pay via paypal your more than welcome!
Not the battery. The battery only supplies power to the mainboard and through that to the lcd. If the battery was at fault then you wouldn't be able to start up. It sounds like you may have heat problems with either the lcd ribbon or with with the flex ribbon connecting the top part of your phone to the mainboard. If I was you I'd check out Mike Channon's site as he is the MASTER of Hermes hardware and if you don't find a solution you can PM him. Heres a link to his site - http://michael-channon.spaces.live.com/
Cheers...
id buy it and sell the parts on ebay
Hey guys, my freind had a sprint Vogue and the touch screen quit working so he gave it to me. Every thing works fine but that. Iv hard reset, reflashed,tried to operate it through MyMobiler, banged it on the computer desk. Nothing works. any ideas or do I just have a new paper weight? Hes already went to sprint and said he lost it and got a new one so sprint will be no help. I really just wanted it for a genuia pig. but its no use when its stuck at the setup screen.
Thanks
Had this problem before, I remember turning the power on, trying the screen, turning it off, on trying again and etc... it worked after a few rigorous tries.
Iv turned it on and off probably 100 times and still no luck. plus the hard reset and reflash
You could try replacing the screen with a spare part from...somewhere. Not much more I can say, that's about as far as my knowledge goes.
Thanks, Im hoping it dont come to that
Sounds like a dead digitizer. You're going to have to either find a new digitizer and going through the hassle of replacing it or replace the entire screen.
which part is the digitizer. I had the same problem with my vogue and bought a part off ebay which i was 99% sure was the problem. its the small electrical board underneath the dpad. There is a connection that the ribbon from the outer screen connects too.. Does anyone know where i can find a replacement for that part. The one I got from ebay looked exactly like the one from my vogue but when i plugged it in it would cause my phone to shut off. They said it was for the GSM touch not the CDMA
Hi all,
Looks like my Sprint Vogue is flaking out on me. The touchscreen is suddenly and without warning not working at all. Everything else works (all other buttons, activesync, all functions). I'd like to do a hard reset before giving up on it, but I'd really like to sync my contacts/messages/photos/etc before doing that. So here's the problem- I use Dashwire to sync, and I'm unable to hit the "SYNC NOW" button!
Any ideas on how to switch to and activate the bottom left and bottom right menu buttons without being able to touch them? For example, the Inbox and Menu buttons on the Mail app screen, or Album/Slideshow on the Photos and Videos screen? If I can get to those I'll be able to activate the sync. Any help would be great!
Thanks,
Bogus
There is a application called "MyMobiler" which allows you to control your phone over ip/usb/bluetooth. If i remember correctly launching the installer on your pc while your phone is connected to activesynch will install it without having to press anything.
Awesome, thank you. That did exactly what I needed it to!
Once it finishes sync'ing I'll give the reset a shot and see if the screen is really borked or not.
No problem glad i could help. If the touchscreen refuses to work you might wanna try replacing it. The part is called a digitzer and they go for 15-20 dollars online. I bought one and it wasn't difficult at all to replace.
Yeah, that's the plan. Hard reset didn't fix the problem, so I'm guessing that part is busted. Between this site and PPCG I found the guide for taking apart the phone, so it's looking like I'll be doing some minor surgery in a few days.
bogus83 said:
Yeah, that's the plan. Hard reset didn't fix the problem, so I'm guessing that part is busted. Between this site and PPCG I found the guide for taking apart the phone, so it's looking like I'll be doing some minor surgery in a few days.
Click to expand...
Click to collapse
How would the touch screen instantly not work?
maybe someone let it fall and put it back to normal like nothing happened
and i know what u mean.I dont wanna give up my vogue. EVER,
but im 15...by the time im 30, i wont remember what vogue is.LOL.
Actually, it seems to have developed a very small air bubble in the very upper left corner. I'm pretty sure that's causing the digitizer to think there's constant pressure in that area, evidenced by the "Start" menu occasionally activating when I turn on the phone. I ordered a new digitizer anyway- the set of torx screwdrivers I'd need to open the case cost the same as a new digitizer and the screwdriver I need. I don't really understand how the air bubble formed (or even what it is contained in), but one way or another I'll resolve the problem next week.
And I just turned 26- I'm sure by the time I'm 30 I'll be sporting a Touch Pro 4 running Windows Mobile 8.5
Well, the digitizer and tools came much faster than I'd anticipated (I won the auction on eBay on Friday, paid same day, and got it in the mail today, shipped from CA to NY!). So I dove right in. It was a straightforward affair- remove the four torx screws from the back under the cover, remove the speaker, pry open the front from the mainboard, disconnect the keypad circuit board from the mainboard and the digitizer from the keypad board, push out the old digitizer, swap in the new one and hook it all back up.
Not for the faint of heart to be sure, but for someone who likes to tinker it was a lot of fun. Took maybe 15 minutes because prying the case from the mainboard was difficult. More accurately, the top plastic case is extremely thin and fragile- if you do this you'll almost definitely crack it in at least one place. If not, you'll crack it pushing the digitizer out from behind. But I'm not that worried about cosmetics, I got my Vogue second-hand off-contract, refurbished, so it wasn't exactly mint to begin with.
On the plus side, the repair worked like a charm! I tested every touch feature I could think of and as many areas of the screen as I could, it actually seemed to respond better than when I initially got the phone. The odd part is I could still see the air bubble in the old screen, and couldn't flatten it out even by squeezing on both sides of it. I wish I knew how it formed so I could prevent it from happening again, but I'll just have to be careful.
So to anyone considering this project:
If you're worried about damaging the casing and have insurance or a warranty or something like that, take it to the phone company to get it repaired.
For anyone else, the $15 bucks for the screen and three tools is a lot cheaper than buying a new phone. Plus you get the geek cred for repairing your own phone.
Hi, I come on here quite a lot for information as it's an amazing resource! This time however, I'm attempting to give something back!
I experienced the "black screen on slide out" on Monday. Phone completely screwed. I've also had a few droppages and had it apart once before so there's no way warranty is gonna help!
I stripped it down and soon discovered what it is that actually fails on the ribbon. The coating had worn through due to rubbing on something during the slide out / in process. it had been playing up for a while, probably due to shorting out on the metal case, but now the tracks (aluminium?) had worn right down.....
In pic 1 i've circled the worn area. The shiny section is where i'd tried taping over it to prevent shorting, before i realised the tracks were gone.
Got an almost new one off ebay for 15 quid and, realising it was going to happen again, came up with a solution that, so far, looks like it will work....
A while back I bought some "anti rattle felt" for my car's dashboard - really thin and strong self adhesive felt to prevent squeaking joins between dash sections. I cut a piece of this and stuck it to the new ribbon. Once this stuff is on it's well stuck, by the way!
See pic 2 for the modded ribbon cable.
On reassembly everything is working just fine so far! Here's hoping that it lasts longer than 6 months this time!
Just need a new casing now as mine is decidedly second hand!
Hope this turns out to be of use to someone!
cool story bro
when i took apart my xperia to replace the housing this seemed like a really weak point in the device. glad to see someone who has had the problem has been able to fix it
Why does the screen go black?
Hi,
When the coating wears off the ribbon cable it exposes the tracks in it. when you slide the keyboard out the exposed tracks short out on the metal casing and the screen loses it's input signal.
thats whats happened on mine at least and i presume quite a few others?
HTH!
Update:
That's interesting: My phone was also losing signal with the keyboard out, and occasionally while closed up as well. It would just randomly drop to "no signal" for a few seconds.
It hasn't done it since replacing the ribbon cable.....could be coincidental of course.
I'm having the same problem
It just started a week ago and I got the phone in January off of ebay. I'm new to opening up the phone so could anyone help me find the correct tools or have a link to a site with pictured instructions?
I noticed that the sliding mechanism started to go loose about 4-5 months ago but didn't expect the screen not respond in landscape mode. I have yet to see the other symptoms you all are referring to. I would like to fix this before it get worse.
In mine case it went totaly black after one week of this problem... You have all the instruction on youtube, there is where i looked. For tools you can be inovative, but the exactly right ones come with housings from ebay, it is only 15EUR, and i bet you have some cracks so it wouldn't hurt replacing. That is what i did, along with ordering new sliding mechanizm, and new ribbon cable.
I am open for ideas to prevent my ribbon cable from being cut at it weakest point again.
I'm assuming my flex ribbon went bad yesterday, since sliding the keypad out causes my screen to shut off.
Already ordered a cable off ebay and will attempt to replace it myself :O
Replaced my flex ribbon cable with one I bought on eBay. The screen doesn't turn on at all now, which leads me to believe the cable I was sent is defective. Put the old one back in and it works okay, less landscape mode. ughhh what a pain.
great tips! my input is I bought a case off of ebay that was ~60$ and everything actually fit fine for me...so I wouldn't discount every seller but you do get what you pay for, the 15$ cases are probablly the ones that will give you problems
I working in a mobilephone repair center if anyone need help drop me a priv... i able to get 2nd hand or even brand new components
Replaced the flex ribbon cable -
I got my flex ribbon cable a few weeks ago and took it to my local repair shop. They replaced it but the LCD screen/optical joystick receives no power. The touchscreen and everything else on the phone works just fine now. I thought it was a defective item so it was exchanged with a new one.
Got the repair shop to replace it again and the outcome still remains the same as the first.
Theres no light coming from the screen nor the side illumination.
I just told the repair shop to just place the original back in for the mean time.
Before the repairs, there would be a flicker of white light and random illuminations. Now there's no lights at all except the power botton.
Could it be defective a batch that the seller was sending out? or the repair shop's mistake and is playing dumb so they do not have to admint fault?
Hopefully there's an easy fix to this problem.
-Also I did inspect the ribbon before and after the repair. looks new as the OEm
Can anybody help me out with this new problem after replacing the cable -
perhaps you should try a hard reset. Ive had problems in the past where the optical joystick and the illuminators did not work, and that worked for me.
On the other hand, the top illuminators are on the same piece of hardware as the flex cable that was replaced, so a faulty flex cable is possible. The bottom illuminators are on the circuit board that the optical joystick attaches to, separate but connected to the flex cable.
Ive recently replaced my flex cable and touchscreen. The experience i had with the faulty touch screen was that it appeared to receive no power, but was in fact displaying a dark backlit illumination that could only be seen in the dark. At the same time however, the screen did not display anything. I'm not sure if this is similar to your experience, but if so then your touchscreen would need to be replaced.
ive done all repairs on the xperia myself, and one thing ive discovered is if something doesnt work right after a repair, simply disassembling it and reassembling it to make sure all the connections are properly done has worked for me in the past.
"Before the repairs, there would be a flicker of white light and random illuminations. Now there's no lights at all except the power button."
Now when you say the power button, do you mean that a red light appears under it?
I dont know if i can come to a conclusion or that i can help (or have helped) you come to a conclusion, but i can only assure you that the xperia acts out in strange and weird ways.
Good Luck!
Tags
Dismantle / Disassemble Sony Ericson Xperia X1
http://www.ifixit.com/Teardown/Sony-Ericsson-XPERIA-X1/788/1
http://www.formymobile.co.uk/xperiadisassembly.php
http://www.youtube.com/watch?v=AWDurQrRt-Y (REAR)
http://www.youtube.com/watch?v=iyGUbxFqvyc&feature=related (FRONT)
http://www.youtube.com/watch?v=elgC8hwHfYQ&feature=related
For info.
Mike
Thanks for the links. I've tried the hardreset and restoring the original rom but the issue is still there. It's really bugging me that everything works but the LCD screen. I'm currently using MyMobiler to use my phone. The touch screen works fine and so does the soft keys. Just no power for the lights. I might just give up and wait for another phone that catches my eye and then tinker with the xperia myself. but if anyone got a solution or want me to test something then I'll give it a try.
My warranty is no longer affective so I'll use my phone as a tester to help others with any problems.
TRIONDAVE, how's your Xperia running now with the cable mod that you did? Its been 6 months since you created the thread. I hope you're still around.
My Xperia X1 works nearly fine, except for the keyboard issues, so I'm thinking of opening it up. If your Ribbon mod helped I might just do it too once I've got it opened. Mine has a MOUNTain of cracks though, and the battery compartment itself is cracked on both side enough to make the compartment CURVED. Hence the Battery cover doesn't sit well.
I'm looking around for broken Xperias which I might be able to use to change the internal cracked casing. Lets see.
DatDereX1 said:
cool story bro
Click to expand...
Click to collapse
My thoughts exactly.
Hello guys, I am in need of real help over here!
Its just that Ive replaced my ribbon cable, the old one got screwd up.
However I got done for 10 minutes ago, tried to start up the phone.. without success :,(
The ribbon cable doesnt have anything to do with the start up, only the screen am I correct? Cause I cannot even start my phone..
Ive connected the charger, but when I remove the battery it shows a red light, meaning no battery, correct?
So what may the problem be exactly? Maybe the battery is all dead, or?
PLEASE HELP!
for the people with ribbon failures how long have you had the phone before it occurred ? im just interested on the cables lifespan.
mine is fine so far but i have noticed the slider is flimsy and rocks left and right.