mini ubs port has gone a bit awol - 8125, K-JAM, P4300, MDA Vario General

i need help!
first off i am the most untechnical peron ever so rather sucky at all this, second i can't afford the excessive repair charges and thirdly i hsve an o2 Xda Mini.
basicly the ubs port socket thingie has gone completely wonky and turned it's self around within the phone. i have searched about the place and i can't find anything that i can understand or helps fix the problem.
basicly is there anyway i can open the phone up myself (i've had a look at the phone and there's no obvious way to get it apart) and put the little socket back into place..because it has gone completely wonky. i think it happened after i dropped the phone on the floor (by accident) and now it won't work with the charger.
any help would be brilliant.
thank you
Amy

If it is turned around within the phone you most likely broke the contacts with the mainboard, you are pretty much S.O.L. However I think Isaw earlier that some forum member can do it. I'd check into that.

Yea - it is probably broken off the main board, but you can open it up and see what is going on if you are inclined to do so.
Service Manual
You will find detailed instructions and pictures on how to open the phone up. The only difference I think in the manual and this phone is the manual does not mention a screw on the main board. When it talks about removing the main board and getting at the rigid-flex board (page 20), it does not mention anything about a screw in the middle of the main board. It's there - that board isn't going anywhere until it is unscrewed. However, you probably won't need to bother with taking the main board out - you just need to get to where you can see the main board since you just want to see the USB spot.

Related

Wizard Repair Guide?! Mines Broken :(

Hey Guys,
Well, I'm a bit gutted really! I dropped my XDA Mini S on the floor with the charger in and the connector IN the phone has come apart from inside the phone. The little metal bit is practically hanging out. I'm wondering, if i were to take the phone apart could i re-connect the little part? (I have a soldering iron if thats as simple as its going to be?)
Just wondering if anyone had any guides on how to take the phone apart and take a look at whats wrong?
Any help would be so much appreciated!
Many Thanks,
Tom
The service manual is hosted on the ftp site.
ftp://ftp.xda-developers.com/Wizard/Docs_Tutorials/
Hope this helps.
I suspect you probably broke the socket off, but if you have a soldering iron, you might as well try to get a new mini USB connector to work with.
You might try Pocket PC Techs:
http://www.pocketpctechs.com/main~unit~UTStarcom_XV6700-554~area~repairs~item~REP-USBCON01~name~UTStarcom+XV6700+Mini+USB+Connector+Replacement+Service.htm
I rang them up about an issue I had (screen on the fritz) and they seemed pretty knowledgeable and helpful.
Alternatively there's a company I found today in the UK. I can't vouch if they're good or not.
http://www.xdarepairs.co.uk/home.asp
Good luck.
Well I also have an issue with my wizzard... the mini jack connector (of the handsfree) is a bit loose.
What I am saying is that it does have a good connection with the rest of the circuit and sometimes the sound of the speaker goes off, then I have to insert the habdsfree and tickle it a little bit until it has a good contact.
? have some basic soldering experience,do you think I should give it a try?
Given my device has been apart too many times for me to admit to I thought I'd crack it open to take a pic for you guys. Not sure if this pic will help for those wanting to do some soldering:
Very large pic: http://farm1.static.flickr.com/216/452691530_f47801708f_o.jpg
Excuse the dust.
Ah! That picture at the bottom is exactly what I needed. The metal but at the bottom (the big sqaure) has totally sheared off....bloody thing. Thanks so much for the info on the repair guides. I may give those repair guys a call if i can't get it to work myself.
Thanks alot you guys
As for you WizeMan, it all depends on if you wish to void your warrenty or not. At the end of the day, I installed WM6 on my device so O2 would give me the finger if i tryed to claim. If I'm honest, I'm getting an upgrade next month so I'm not to bothered if I balls it up! Would be nice if I got it working though....
Lemmie know how you get on
unlock k-jam
i read all your write about how to unlock k-jam device but after all i get this message:
Lock Status: 0000000000000000
SIMLock Code: █⌠═eי∟80Γ█Σ☻< δ♠
how can i get it from this .........
lironasseo said:
i read all your write about how to unlock k-jam device but after all i get this message:
Lock Status: 0000000000000000
SIMLock Code: █⌠═eי∟80Γ█Σ☻< δ♠
how can i get it from this .........
Click to expand...
Click to collapse
A little bit of a thread hijack but that means it is SIM unlocked.
Let me tell you my news, my friends.
I opened my Qtek 9100 and fixed two serious issues regarding this phone, using... sponge (the one we use to wash the dishes)
1. I put some into the stylus socket (from the thin space it has) and also
2. On the top of the mini jack socket so when i assembled the housing it blocked it from moving (2 of the contacts are no more soldered and i dint have a soldering iron at that time)
Anyway, both operation went ok and my phone is more than fully functioning. Now the stylus is hardly (in a good way) comming out (it first gets longer then comes out).
I wanted to do also the safe singal fix, but didnt find the photos to apply it correclty, so if someone has them, please give link. If you need any info about the "Sponge" Hacks, just post or pm
WizeMan said:
Let me tell you my news, my friends.
I opened my Qtek 9100 and fixed two serious issues regarding this phone, using... sponge (the one we use to wash the dishes)
1. I put some into the stylus socket (from the thin space it has) and also
2. On the top of the mini jack socket so when i assembled the housing it blocked it from moving (2 of the contacts are no more soldered and i dint have a soldering iron at that time)
Anyway, both operation went ok and my phone is more than fully functioning. Now the stylus is hardly (in a good way) comming out (it first gets longer then comes out).
I wanted to do also the safe singal fix, but didnt find the photos to apply it correclty, so if someone has them, please give link. If you need any info about the "Sponge" Hacks, just post or pm
Click to expand...
Click to collapse
I'm still trying to get the a new fascia and will probably shove an eraser bit into the stylus spring mechanism to ensure the defect never happens. Also how did you discover the break in the solder joints on the headphones jack? I have a funny situation where the left channel of the headphones doesn't work but I suspected the headphones (the plug has to be pulled at an angle to get any sound out of the left) but now I am thinking it may be the socket itself.
By the way the reception fix pic doesn't load for me either but I unless you truly need it, don't waste your time doing it; I always have all 4 bars and sometimes have 2 bars.
AsGF2MX said:
I'm still trying to get the a new fascia and will probably shove an eraser bit into the stylus spring mechanism to ensure the defect never happens. Also how did you discover the break in the solder joints on the headphones jack? I have a funny situation where the left channel of the headphones doesn't work but I suspected the headphones (the plug has to be pulled at an angle to get any sound out of the left) but now I am thinking it may be the socket itself.
By the way the reception fix pic doesn't load for me either but I unless you truly need it, don't waste your time doing it; I always have all 4 bars and sometimes have 2 bars.
Click to expand...
Click to collapse
Allright here is the deal.
1. I found out the break in the soldier joints when i opened it. I was really suspicious about it because when i inserted my headphone jack into the connector, i had problem with the contact; the connector was loose and it muted my phones speaker. When i disassembled the phone using the service manual i saw with my eyes that the the joins where f-ed up.
2. I dont really need the signal hack i just wanted to experiment, i have 2.25.11 cingular radio rom and its great.
Btw i suppose you should better use the sponge, because the rubber may wear off but not the sponge...
Thanks for the tip on the sponge. I am going to grab a used but allegedly "like new" body from eBay and also get one of those covers as well.

MDA DEAD!!!!!

Well ladies and jerks, I regret to inform you that my MDA is completely dead. I was in a car accident the other day and it went flying through the air and when I grabbed it off the floor of my car the USB charge plug was loose and had trouble connecting to the computer but still worked. Since then I had put a drop of super glue in there to hold the plug still and everything was fine untill this morning. My phone was left off with no battery in it untill the glue dried and still, everything was fine.
Now this morning when I went to grab my phone it was completely frozen and had 1% of battery life left so I soft reset and plugged the phone in and it was charging fine. I connected it to the computer and it would not connect at all. Now after playing with the cable a bit to get it to connect to the computer, the charge port is completely dead. It will not even let it charge with the charger and the little silver piece inside the plug is falling out.
Does anyone here have any idea what I should do to save my Wizard? I fear it may be the end for it.
Here's the big problem though. My device is CID unlocked and still has the TNT.1437 firmware on it so my warrenty is completely void. T-Mobile will not send me a handset exchange like this.
hi
t-mobile wouldn't send you a warranty replacement even if you had the official windows mobile on it. that is because, after you read the terms and conditions of the warranty, it does not include and in fact states quite clearly that 'excessive' use of the usb cable resulting in damaged charging port will not be replaced.
i realise this is not very helpful, so allow me to be helpful!
download the wizard service manual, if you PM me your email address i can email you a copy of one
what you will have to do is first obtain a new mini usb port from ebay or somewhere similar, i will try to hunt one down in america for you
following the service manual, you need to dismantle your handset, use some sort of rubbing alcohol (nail varnish remover) to get rid of the super glue you put on, first try to re-solder the old connector back onto where it came, or if not solder on the new one after removing the old one.
to be honest, you dont have anything to lose, but you could gain a working mda again!
good luck, and just a disclaimer to say im not responsible for any damage done to yourself, your device or anything else.
duke_stix said:
hi
t-mobile wouldn't send you a warranty replacement even if you had the official windows mobile on it. that is because, after you read the terms and conditions of the warranty, it does not include and in fact states quite clearly that 'excessive' use of the usb cable resulting in damaged charging port will not be replaced.
i realise this is not very helpful, so allow me to be helpful!
download the wizard service manual, if you PM me your email address i can email you a copy of one
what you will have to do is first obtain a new mini usb port from ebay or somewhere similar, i will try to hunt one down in america for you
following the service manual, you need to dismantle your handset, use some sort of rubbing alcohol (nail varnish remover) to get rid of the super glue you put on, first try to re-solder the old connector back onto where it came, or if not solder on the new one after removing the old one.
to be honest, you dont have anything to lose, but you could gain a working mda again!
good luck, and just a disclaimer to say im not responsible for any damage done to yourself, your device or anything else.
Click to expand...
Click to collapse
I sent you a PM with my email
dharvey
hi
so sry to hear about ur accident and damaged MDA
t-mobile will certainly wont give u warranty replacement. It happened with me once also and only way out was ,I took it to a mobile repair shop and got the usb connector replaced for very nominal price.
duke_stix is right,get a mini usb and solder it. If u can do it,very well or take it to a techy to do it properly.
Once it's repaired it will be as good as new,goodluck
duke_stix said:
hi
t-mobile wouldn't send you a warranty replacement even if you had the official windows mobile on it. that is because, after you read the terms and conditions of the warranty, it does not include and in fact states quite clearly that 'excessive' use of the usb cable resulting in damaged charging port will not be replaced.
i realise this is not very helpful, so allow me to be helpful!
download the wizard service manual, if you PM me your email address i can email you a copy of one
what you will have to do is first obtain a new mini usb port from ebay or somewhere similar, i will try to hunt one down in america for you
following the service manual, you need to dismantle your handset, use some sort of rubbing alcohol (nail varnish remover) to get rid of the super glue you put on, first try to re-solder the old connector back onto where it came, or if not solder on the new one after removing the old one.
to be honest, you dont have anything to lose, but you could gain a working mda again!
good luck, and just a disclaimer to say im not responsible for any damage done to yourself, your device or anything else.
Click to expand...
Click to collapse
Good advice except don't use rubbing alcohol, it damages plastic. Use adhesive remover instead. (At my hospital we use little adhesive remover wipes similar to the alcohol prep pads.) We are told to use this method when cleaning adhesives from plastics and it works.
duke_stix said:
hi
t-mobile wouldn't send you a warranty replacement even if you had the official windows mobile on it. that is because, after you read the terms and conditions of the warranty, it does not include and in fact states quite clearly that 'excessive' use of the usb cable resulting in damaged charging port will not be replaced.
i realise this is not very helpful, so allow me to be helpful!
download the wizard service manual, if you PM me your email address i can email you a copy of one
what you will have to do is first obtain a new mini usb port from ebay or somewhere similar, i will try to hunt one down in america for you
following the service manual, you need to dismantle your handset, use some sort of rubbing alcohol (nail varnish remover) to get rid of the super glue you put on, first try to re-solder the old connector back onto where it came, or if not solder on the new one after removing the old one.
to be honest, you dont have anything to lose, but you could gain a working mda again!
good luck, and just a disclaimer to say im not responsible for any damage done to yourself, your device or anything else.
Click to expand...
Click to collapse
Thanks. Have you had any luck trying to find a service manual? I have been looking but with no success...
Well I managed to find a wizard service manual written in English for the US and got my MDA taken apart correctly without damaging it(I hope) only to find that all 9 contacts for the USB port are completely severed. Unfortunately I don't have the soldering skills to fix this on my own and there are no local repair shops where I can get it fixed seeing as how I am also out of a car...(see first post) so I am back to a Razr... UGH.... Anyways, I will remain an active member of the community and continue to help others with issues they may be having and help others flash roms because I found that I enjoy helping others.
I will, however, be leaving for a period of time in a few months because I am being deployed and most likely will not be returning with a Wizard but an HTC TyTN II. Don't worry though, I won't forget my friends back here in the Wizard forum( I know too much about these things to just pack up and leave now...)
Hi
sry to hear that,
But just another idea popped in my mind,if u can manage to get mini usb port than u can take it to any electronics repair shop, like tv,radio or any pc repair shop,it can be soldered,since u say u have the service manual u can show them the circuit layout,they can fix it.
yet,if u happen to have any sort or make of mobile (Motorolla,Nokia,samsung) which is pretty old and spent,of which u got no use,c if it has a mini usb port,usually every mobile does have it,and it has 9 connectors,take it out and get it soldered to ur mda.
Well, since its gonner,there's no harn in trying,
zabardast_1 said:
Hi
sry to hear that,
But just another idea popped in my mind,if u can manage to get mini usb port than u can take it to any electronics repair shop, like tv,radio or any pc repair shop,it can be soldered,since u say u have the service manual u can show them the circuit layout,they can fix it.
yet,if u happen to have any sort or make of mobile (Motorolla,Nokia,samsung) which is pretty old and spent,of which u got no use,c if it has a mini usb port,usually every mobile does have it,and it has 9 connectors,take it out and get it soldered to ur mda.
Well, since its gonner,there's no harn in trying,
Click to expand...
Click to collapse
Thats a good idea, but I will probably just end up buying a new one off ebay for my girlfriend and play with hers all the time and then I already bought a TyTN II for myself.
Thanks.
So how about that manual??
That would be Sweeeet !!
[email protected]
Thanks for any consideration this may get :thumbsup:
TainT said:
So how about that manual??
That would be Sweeeet !!
[email protected]
Thanks for any consideration this may get :thumbsup:
Click to expand...
Click to collapse
Here is a download link. I just uploaded it.
http://www.megaupload.com/?d=BEG0XKM8
and a mirror:
http://www.megaupload.com/?d=E11DVNQC
What a resource
The links an awesome asset, Im sure peepz will be benefiting for years thanks to you.
Thank You Sir...
dharvey4651 said:
Well I managed to find a wizard service manual written in English for the US and got my MDA taken apart correctly without damaging it(I hope) only to find that all 9 contacts for the USB port are completely severed. Unfortunately I don't have the soldering skills to fix this on my own and there are no local repair shops where I can get it fixed seeing as how I am also out of a car...(see first post) so I am back to a Razr... UGH.... Anyways, I will remain an active member of the community and continue to help others with issues they may be having and help others flash roms because I found that I enjoy helping others.
I will, however, be leaving for a period of time in a few months because I am being deployed and most likely will not be returning with a Wizard but an HTC TyTN II. Don't worry though, I won't forget my friends back here in the Wizard forum( I know too much about these things to just pack up and leave now...)
Click to expand...
Click to collapse
First and Foremost,
Thank you sir, for answering the call of your nation. This American & his family thanks you from the bottom of our hearts.
In my ancestral culture's view, a patriot is second only to Saints & the Lord himself. May God watch over you & your team members.
I HAD to tell you that because every serviceman needs to know just how much Americans honor and cherish you!!!
(NEVER pay attention to the liberal media, they are sick diseased haters & hypocrites who are lucky to live in a land where they are allowed to lambast & denegrate those who are truly honorable.)
About your wizard, there are several ways to connect electronic components these days. If an adhesive was used, forget about it. If it was truly soldered, nothing can be easier! You can do it yourself (make sure to get a bulb vacuum for removing old solder and a modern soldering gun). It is so easy, in fact, that a authorized repair facility may do it for you for cheap! And you could always mail it to them, too.
Good Luck & God Speed dharvey4651.
similar problem?
My MDA will charge fine through the USB cable, but will not sync/connect -- it's not even appearing in Device Manager.
Does anyone know if this is definitely a hardware issue, presumably involving the USB port?
Thanks in advance,
Will Stewart
it is possible, your USB cable has problem or try another PC.
If you still cannot fix, donate to me ...

Tytn / hermes / 8525 freezing up when I slide close

It seems that my 8525 with Black Satin (WM6) has recently started crashing when I slide it close after sending a message or after sliding it open when recieving one.
The screen goes all dim and interlaced looking but it's really "off" as when I press the power button it actually boots up. When this happens that current text message is GONE poof!
I sat there and slid it open and closed 20+ times and couldn't repeat it but when trying to use it for real is when it freezes. It's not only with the text messaging though as I tried to slide it open to reply to a message on the internet (via wifi) and it locked up there also.
I did a search and haven't really found anything... guess I could reinstall but man, I hate having to do that... what all will I need to rememeber to back up? Text messages, phone numbers, settings for tomtom? bah!
Anyone ever experienced this?
Great, I think it's a loose connection somewhere... I noticed it was out and I had only put it down, not closed the slide. So just now when it was just idle I tapped on it and poof it locked up.
Great... Now what!
gilligan8 said:
Great, I think it's a loose connection somewhere... I noticed it was out and I had only put it down, not closed the slide. So just now when it was just idle I tapped on it and poof it locked up.
Great... Now what!
Click to expand...
Click to collapse
If it's still under warranty, take it in and have them look at it.
If it's not, look for one of the many disassembly instructions around, take it apart and reseat the cables.
I took mine apart not long ago to fix a non-working camera and it was amazing easy to get into the phone and remove and reconnect the cables.
Just make sure to read everything before trying it.
I bought it off ebay (supposed to be brand new) to unlock and use on a regional company's network. So doubt I'm covered.
http://pdasmart.zftp.com/instructions/Cingular 8525 Instructions.pdf
Is that a sufficient set of instructions? I'm not opposed to doing this, I repair laptops all the time and they are just about as difficult if not worse sometimes. I had attempted to take apart a friends dead 8525 a year or so ago but didn't know where the retention tabs were to get it opened beyond the obvious screws.
gilligan8 said:
I bought it off ebay (supposed to be brand new) to unlock and use on a regional company's network. So doubt I'm covered.
http://pdasmart.zftp.com/instructions/Cingular 8525 Instructions.pdf
Is that a sufficient set of instructions? I'm not opposed to doing this, I repair laptops all the time and they are just about as difficult if not worse sometimes. I had attempted to take apart a friends dead 8525 a year or so ago but didn't know where the retention tabs were to get it opened beyond the obvious screws.
Click to expand...
Click to collapse
That would be the basics. I noticed that it doesn't say anything about the tape for the large ribbon cable, so there may still be some snags if you use those (I don't know if the tape is present on all the various rebadges of the hermes).
Nice that they use a tool to take it apart, I used something like a debit card on mine.
If you are comfortable disassembling a laptop, you should be fine. As with a laptop, just take it slow and be careful.
(shudders at the memory of disassembling a compaq and Apple laptop)
Word, I hate working on laptops... but I guess I got to!
I'll bet it is the battery header on the board. I had a similar issue and needed to repair a solder joint there.
same here.. i was lucky it was still under warranty..
good luck with the dissasembly!
it has been rather calm lately... though I am a lot more gentle when sliding it open and close...
I know it couldn't have been a fluke... maybe some dirt got in and now is out... I'm sure I will have to get at it eventually... till then I'll just keep treading lightly!
Oh, and Mike, thanks for those links... VERY good stuff!

[Q] Mytouch 4g wifi not functional after LCD replacement

I just recently replaced a malfunctioning LCD and shattered digitizer for my Glacier. Before I did that, the WIFI worked just fine. No problems at all. But now, the WIFI will turn on, but won't pick up any networks at all. All my other phones pick it up just fine, as well as my laptop. I've tried three different ROMs and I have the same issue with all of them. As far as I know, there weren't any cables that connected the WIFI module to the motherboard or anything else when I took it apart and put it back together. It's just a little piece that snaps into place, right? I'm not sure what's going on with this...
Seriously? Nothing? Every time I post on here, I get ZERO response... What gives? I see everyone else's problems being solved but not mine...
Sorry, there's no help to give. Don't act like you're entitled to something. I hate people like that. If you didn't touch the WiFi module through the screen and tried different roms then it went bonkers and its toast. TF are we supposed to do about that
Sent from my HTC Glacier using xda app-developers app
If you're gonna post on here just to be a douche, you might as well not post at all. It's doing nobody any good.
All drama aside, he is right nothing to be done really. I guess you could open it back up again and risk breaking something more important than the wifi. Something may be put back in wrong or may have got ESD damange. Truth is unless you're just using this phone as a toy/dev/learning device and don't care if it breaks it is not worth the risk to open it back up.
Trying to fix my external speaker - I mess up working wi-fi. In addition, the case crack and camera button is not working. Should take it to repair shop. Too late now. It would be too expensive to fix it. You my still be lucky and shop will fix for few bucks. Lesson learn - do not mess with something that you do not understand( for me).
coax cable issue
there's 3 little coax cables - I've been told the white coax is the wifi but the black one fixed it so maybe they are all involved. In the process of getting to the LCD you went through these 3 cables. In most cases you wouldn't have disconnected them but certainly by accident it will happen. I put mine on 3 times before they stayed. There's quite positive click when connected but even then it may come loose while assembling the rest of the phone. I just finished swapping out my mother board and as perfectly as I could reassemble the phone I apparently lost one of the coax connections = no wifi. Went back in and this time the black cable somehow got caught under the camera board instead of on top and connected. Easy to see why this was missed because it looked connected.. well looked like it belonged where it was (wrong)
Anyway that's my wifi fix story - hope it helps someone

Two MOTO 4G Play Questions

1. I had to replace the screen a little while ago. All went well except that I damaged my on/off switch button and I need to replace it. I'd also like to replace the volume pushbutton as I bent, but, was able to this one back in shape. The on/off button is held in place by a piece of tape.
I can find replacement buttons for the moto g4, but, the picture looks to be different than what I remember. It is confusing that they have several phones with such a similar name. I also know that many online places don't necessarily even use the correct picture for the specific item on sale to begin with.
I did find an official motorola online forum where they just said that phone has no user repairable parts. I guess I'm a technician/user then and need a replacement part. I never did figure out how to log in to that forum to try to get an answer or even part number.
I managed to damage the part when removing it, but, I imagine they would survive pretty much everything else the might destroy a phone. I haven't really been able to find any listing of very broken ones either.
Any help?
2. I also notice that while playing music via bluetooth to my car stereo that sometimes there is some noise. It sort of sounds like you would get if a potentiometer needs cleaning or the output jack has dirty contacts or gets jostled. Then I remember there are no wires and no potentiometers involved in this situation.
I did read somewhere that this is just a problem with that phone and there is no fix. I get it, it is basically a throw away phone, but, is this really the case. Was this an issue, was their a fix? and/or is there a way to get a replacement that doesn't have this problem or some way to upgrade to another model that doesn't have this issue more affordable?

Categories

Resources