hi,
I recently bought the Antha VPN Client to get access to my university WLAN
(via Nortel gateway).
The software runs properly on WM5 except that it can't connect to anything at all. I do not know if it is a Antha VPN problem, a WM5 problem or a hardware problem with the MDA pro. The software seems not to recognize the built in WLAN of the MDA pro (at least I connot select WLAN among the networks).
But it also won't work with "Internet" ot "ISP". If I chose "ISP" it starts to connect, but then disconnects.
Maybe anyone of you has experience with VPN clients on the MDA pro.
How are the profiles in WM5 "Internet", "ISP", "Work" etc, related to each other?
Is there any hidden firewall, or the T-mobile branding blocks the software etc.?
Thank you very much for every idea and best regards,
Elias
I also had issues with Antha and conatct support where i was told that M5000 (Universal)is not supported yet and that they also have issues.
Unfortunately when i looked at the supported systems i thought that i had seen the SPV M5000 (or Universal or whatever it is called) but it was another one with a similar name.
I think we have to wait until they find a fix for it.
Unfortunately there are not a lot of VPN's out there which work with Windows Mobile 5. I tried NCP Secure Client, but don't get it working either, but this is maybe because of parameter. You may give this one a try.
Ingo
my 2 cents... give your sysadmin a tip and switch to openvpn, hassle free and damn-working ssl-based vpn. There is a openvpn pocketpc client in the works, and it's running pretty fine.
See you at the openvpn pocketpc forum
Hi,
I have a little problem that I am sure there must be an easy solution to!
I have set up a VPN on my Universal to connect to work. The problem is that my work's VPN server allocates me an ip address in the 10.x.x.x address range. All servers that I need to access behind the VPN have addresses in this range as well. Unfortunately, my ISP (T-Mobile UK), also allocates an address in the same range. Therefore, whenever I try to acccess a server at work, WM5 suffers confusion since it doesn't know whether to route the message through the VPN or directly out to the internet through the cellular modem.
I have been able to verify that the VPN thing works if my work network was on a different network address since initially, I was unable to VPN into my PC at home for the reason described above. I changed the ip addresses of all machines on my home network and now everything works fine at home.
Unfortuantely, I am unlikely to convince the IT people at work to change the address of all their machines. Similarly, I don't think I will have much success with T-Mobile and so is there anything I can change at my end to avoid this problem?
Thanks in advance for any help.
Mark
Narrowing the ip address may help, eg 10.0.0.1 is different to 10.1.0.1.
are you using this over wifi or gprs? if the phone provider is involved, I assume its gprs.
you could try and esablish your ip address as fixed rather than part of the pool, so the it guys assign a range for remote connections as say 10.0.0.100 to 10.0.0.150 as remote dial in connections, thus giving you a separate number.
the best way though I would have thought is for you to a fixed ip address known to you and the servers, and then hard type the ip address as your vpn settings, then establish that ip address as part of the exceptions settings.
in order to use exceptions though you have to know the range, or the exact ip address you will be assigned, and must be different to your telco.
not much of a solution, just some suggested areas to look at.
cheers
s.
hi guys, just out of curiosity what software are you using for VPN? on my laptop my company has installed cisco vpn, does it need to be a cisco vpn for wm5?? :?
From bad to worse...
Thanks for the reply Simon.
Unfortunately, I just went to try out some of your ideas and discovered that I can't get the VPN to connect at all now. It used to connect OK but then have routing problems whenever I tried to access anything. And my home VPN worked perfectly. Now, I can connect to neither.
I simply switched over to an O2 sim and with minimal configuration changes could verify that my setup still works OK and so it must be something to do with T-Mobile blocking ports. They weren't blocked yesterday!!!
Yesterday I "upgraded" my GPRS account from T-Mobile's Web'N'Walk to Web'N'Walk Professional and now I find I have this problem. Is this just a coincidence, or could it be that the Pro version has more severe restrictions than the consumer version?
I have emailed Customer Services to see what they have to say.
I will post back when I get a reply from T-Mobile.
mstar, I am no VPN expert, but for me, using a Windows XP hosted PPTP VPN it works after a fashion (above problems excepted!). I am using the VPN client built into Windows Mobile 5. I think you stand a good chance of getting it working using the built-in client.
Mark
I simply switched over to an O2 sim and with minimal configuration changes could verify that my setup still works OK and so it must be something to do with T-Mobile blocking ports. They weren't blocked yesterday!!!
Click to expand...
Click to collapse
I've heard on the grapevine that T-mobile have explicitly refused certain types of traffic on the web-n-walk
VOIP is the biggy...
I was seriously thinking about getting signed up - but no point if IPSEC is a prob, as well as VOIP.
Not sure how they can tell it's Skype traffic :?
http://www.reghardware.co.uk/2006/05/09/t-mobile_bans_voip/
for more info
An Update
An update on my VPN problem. Yesterday after total failure to get the VPN to connect, I emailed T-Mobile customer services.
Although they have not replied, when I tried it this afternoon I found that it was working again as before even though it had not been working first thing this morining. Of course I have not changed anythng at my end to cause it to break and then start working again (but they all say that, don't they!).
So, I don't know whether this was just a momentary fault, or whether T-Mobile have changed something to re-enable the VPN ports for me. I can now VPN in to my home PC, but the problem connecting to my work VPN with the 10.x.x.x address remains.
So, Sikkutz, depending on the address of the remote network, you may or may not be able to get a VPN to work using T-Mobile's Web'N'Walk.
By the way, my VPNs both use Microsoft's PPTP and not IPSec and so there may be different issues with that protocol.
I have discovered that O2 provides a separate acccess point, vpn.o2.co.uk, that causes a public ip address to be allocated to the device, ie not on the 10.x.x.x network. It would seem that this is designed to address this very problem. Does anyone know if T-Mobile can provide something similar?
Mark
There must be a solution
Hi!
I have the same problem with my Qtek 9000 (VPA IV). I can connect to my VPN Gateway but the routing into LAN failed. I get a 10.x.x.x address from Vodafone Germany and my LAN uses 10.98.8.X. :-(
But there must be a solution! My previous Qtek 9010 (VPA III) had the same problem, but it was able to route between the 10.-networks after a firmware-upgrade to version 1.40.01! But I don't no why!
What was changed in firmware to enable routing???
Daniel
i have the same issue aswell, I am reluctant to change the IP range of my machines as that usually causes trouble for the servers
Any other ideas?
Thanks
maybe stupid thing, but did you guys try dna forwarding (that is what I use from home office, not on pda to be honest..
Maybe I just did not get your point....
What kind of VPN server do you use? I'am using a Cisco PIX and use a PPTP VPN almost everyday. I can use the 10.1.x.x network at the location the PIX is located (this PIX is directly connected to the 10.1.x.x network).
I can't however use any of the remote offices using 10.2/10.3.x.x etc.
This is becaus of the lack of routing abilities in the PPTP implementation.
With an IPSEC tunnel (additional software needed) the remote offices can be reached without any problems.
I know that some IP implementation disallow routing between a public address and any 10.x address. To solve this you could give your VPN clients an address from a 10.x subnet .
hi sorry been away awhile,
I use the routing and remote admin snapin of Windows server 2003 to manage my VPN, I can connect fine using the phone as a modem with my notebook but as soon as I try accessing any URL/resource on my network it fails, e.g. we have a intranet site on http://servername but it wont open this up.
Any Ideas?
Hi,
Has anyone managed to get a VPN connection working properly with t-mobile web'n'walk? I suspect this wont work as all t-mobile connections are sent through a transparent proxy but I just thought I'd check. I remember reading on the Internet that they have a different GPRS access point for VPN connections but they won't give me access unless I'm a business customer. Has anyone managed to get this provisioned on their account? It seems a bit of a con to sell phones that are capable of VPN access and then to tell their customers they can't use it. Does anyone know if the web'n'walk pro service give it's users a public routeable IP address?
Can't imagine they do... Read a figure of 2,500,000 3G phones sold as opposed to the expectation of a few hundred thousand on a MoDaCo thread... I just don't think they'd have the available ipblocks, even though they're given connectivity by the Deutche Telecom aspect of their business... Doesn't seem feasible.
Surely if you initiate a VPN from your phone to a server, the transparent proxy will know to route any incoming responses back to your device?
Hi I have an O2 XDA Exec (personal contract) with the BB Connect software up and running. I also have a Blackberry 8700 that connects to BES at work on the O2 network (BT Mobile I think). I can get BB Connect to work with regards to email, and everything works well
However, when I use the blackberry I can use Opera Mini to surf the web and Google Maps Mobile, so I know I have access to data.
When I put the SIM card in the XDA I can't seem to get the data connection working. I have tried several APNs - o2.wap.co.uk; mobile.o2.co.uk and blackberry.net, but none seem to give me access.
I am aware that my compnay may well have blocked some ports/protocols, but as I can access Opera Mini and Google Maps from the blackberry there must be data there somewhere. Anyone got any ideas as to how I could do it?
Guru Meditation said:
Hi I have an O2 XDA Exec (personal contract) with the BB Connect software up and running. I also have a Blackberry 8700 that connects to BES at work on the O2 network (BT Mobile I think). I can get BB Connect to work with regards to email, and everything works well
However, when I use the blackberry I can use Opera Mini to surf the web and Google Maps Mobile, so I know I have access to data.
When I put the SIM card in the XDA I can't seem to get the data connection working. I have tried several APNs - o2.wap.co.uk; mobile.o2.co.uk and blackberry.net, but none seem to give me access.
I am aware that my compnay may well have blocked some ports/protocols, but as I can access Opera Mini and Google Maps from the blackberry there must be data there somewhere. Anyone got any ideas as to how I could do it?
Click to expand...
Click to collapse
As far as I know blackberry and internet are two different connections. As you can use blackberry on your universal you need to get the internet connection setting from your provider (It should be here in the forum as well) and manually create a connecting setting and you should be able to view the web pages as well.
When you use the internet connection your BB connection will be disconnected as you cannot have two connections at the same time.
Hope this helps.
Right, it's taken me a while, but I've got a bit further with this. The reason my blackberry can access data, but using the same SIM in my Universal it can't is all to do with the blackberry connect client.
As my companies SIM won't enable 'data' (ie the WAP or internet APN) the data is coming via the Balckberry BES MDS service. This allows the BES to act as a kind of proxy for data.
The bad news is that the Blackberry connect client on WM5 doesn't support MDS. The good news is that the Blackberry Suite for WM6 that has just been announced http://www.techatplay.com/2007/04/24/blackberry-to-run-on-windows-mobile-6/ should.
Bring it on!
Hi, I'm off to spain next month and know a good spot for free wifi, however I have the usual problem of not being able to send email via outlook on my spv m600 device. I am aware that this relates to smtp settings.
Is there a way of finding out the smtp settings, e.g. by discovering the service provider? The wifi is unlocked and available in a central square so good for a coffee and surf/email. It isn't advertised in any of the cafes or anything, so can't ask anybody - might be a nearby hotel or house or business. Think it goes by the name "wlancomtrend".
Is there a software solution, or other way to find out ISP and smtp. I will try smtp.telefonica.net but if that doesn't work then what next?