Prophet does't work...Help - JAMin, XDA Neo, S200 General

Hi my friends. I hope you help me in my problem. I have a prophet. For a long time i had installed wm6 touch evolution rom. This afternoon i had the phone closed and when i turned iit on it didn't load windows but when the windows mobile screen appeared i heard a sound and the phone turned off. I restarted and restarted for many times but nothing... I did a hard reset but the same problem. The bootscreen appears and when the screen changes to windows mobile bootscreen i hear a sound and then the device stuck. I installed the same rom i already had but the same problem. Then i decided to install the original rom O2 Germany but for one time again i had the same and the same problem. What can i do? Can this problem be fixed?

Hi guys. I think that i have find what is going wrong. I reinstalled O2 Germany rom and when the installation finished the phone is restarting. That time i didn't discinnected from usb cable and the phone didn't restarted or stuck. Is it possible that the batterrie has problem? The phone is starting only if it is connected to current via usb or via electric charger. Is this possible? My batterrie didn't have problem since this afternoon. When the batterrie was fully charged its duration was 2-3 days. Please give me a reason

Related

My SVP M600 phone got stuck at Starting screen

Hi Friends,
My new mobile phone SPV M600 got stuck whil starting showing four lines of messages as shown below.
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 2.10.1.22
Can any one please help me in geting my phone to today's screen.
I also attached the screen shot for reference.
did you try a hard reset ?
Ya I tried both hard as well as soft reset but same screen is stuck again and agian.Can any one please help me in this regard as I am very new to PDA family.
Ok, first things first:
Since you are new to this, are you sure you preformed a hard reset?
It is done by holding power + camera + comm manager buttons (one on the right, two on the left) and pressing with stylus in the reset hole at the same time.
A message should appear asking you to press 'send' (green phone button) to confirm reset.
If this does not help, you may have a serious problem.
Please answer the following:
Is the device fully charged?
Phone will fail to boot if the battery is too low.
Did you install any software right before this happened?
This should have been resolved by hard reset, but just in case I am asking.
Did you change the ROM, attempted CID / SIM unlock?
This could require more serious measures than I can advise on.
I did exactly the same thing which you mentioned.But even then it is stuck at the same screen.
Ya u r right I unlocked my mobile using a software from eBay.The unlock was successfull and I tried to insert T-Mobile sim, it also captured the signal and I was able to make and recieve calls then after that I wantedly switched off the phone and then tried to start it, there got the problem.
Can any one help me in this regard please.
I am having the same problem, but my phone is not sim-locked.
I've got the same problem after attempting smart1_wm6_pp8mb.exe
I'm having the same problem with my G4 QTEK S200:
Attempted to upgrade to WM6 Rom using smart1_wm6_pp8mb.exe
After reboot the phone got stuck at the QTEK Screen
Tried Hard Reset (Camera+Power+Comm+Reset) followed the steps with the same results (bricked)
I also tried re-flashing the rom back to the factory one using RUU_Prophet_220734_2207114_024721_QtekWWE_Ship and ROMUpdateUtility-NoVendorID.exe in Windows Vista with WMDC (Windows Mobile Device Center v. 6.0.6873) and the phone in boot loader mode (tri color screen) with working USB cable, with windows firewall disabled and symantec AV disabled as well, RUU keeps saying error 260 "the update utilitiy cannot connect to your pda phone..." .
Do you think I should try this process using XP instead? No matter what i try i keep getting the error 260
Any help would be greatly appreciated
Got it fixed!
it was definately a Vista issue. once i tried it in XP with ActiveSync it worked like a charm and i got my phone back up and running. also used spb backup and restored all my settings.
ipl/spl screen
i got the same problem with new rom wm6, and the 260 eror, my problem is that i have xp and the activesync does`t connect ...
... means i cant redo the original rom ????
PLEAAASEEE HELPPPP !!
Again My phone SPV M600 got stuck at IPL/SPL screen
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
yekanth said:
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
Click to expand...
Click to collapse
A rom reinstall on xp solved my problems on that one. retry a couple of times! It may not work the first time! hard reset as well...
Try an official wm5 rom just in case
good luck
Can you please gimme step by step procedure
HI Phil,
I am new to these kind of installations . CAn you please Gimme step by step procedure for ROM installation.
mine is now also stuck, after trying to install new rom. wont connect to active sync either, have i fooked it? tried hard reset etc.
thanks
(with a turned off phone, press and hold camera button then insert USB cable)
then flash provider ROM
RECOVERING FROM ERROR IN STEP 8 WM5->WM6
1. Don't panic
2. Don't panic
3. Unplug the phone
4. Reset with stylus,and keep the Camera Button pressed.
5. A 3 color screen will appear(Bootloader Screen)
6. Connect your device with your PC,and run the NVID(no vendor) WM5 rom.
7. The device will be resetted after RUU(rom update utility)finishes
8. Repeat the WM6 upgrade,from STEP 5..
Click to expand...
Click to collapse
from here http://forum.xda-developers.com/showthread.php?t=310452
hi jay
i seen your post in n00b guys one, i fixed it!!!!, thank you so much, i couldnt remember how to get it to those 3 colours.
thanks again
Colin
Hi Iam unable to get the NVID ROM
Hi,
I am unable to get the NVID ROM. The Rapidshare link that has been provided in the other thread is not working. Can some one tell where can i get the ROM.
collywog19 said:
i seen your post ...
Click to expand...
Click to collapse
no problem mate.
..and yekanth i see what u mean about the dead links. i have the files on my computer at home but i'm posting from my prophet right now, so i can't upload. Try using the "pdaviet temp" from one of the wm6 threads?
(http://rapidshare.com/files/54265407/Prophet_PV_Temp.zip)
Hi Iam able to update the Rom but no use
Hi,
To mention my phone is from orange-UK. I got the orange rom from our FTP site and did the flashing/update what ever you say.But still it is getting stuck at the same IPL/SPL screen. Iam very much worried that I will not get a proper solution for my problem.It will be very grate full if some one resolve my problem.
just seems strange...how did you fix it last time? did it just start working again? A random guess would be that the camera button got liquid spilled on it or is stuck in.
If the camera button is pressed in the phone will go to 3 colour screen every time it is turned on.
It won't do any harm if you try to press/move that button to see if u can "unstick" it, not likely I think but u never know...

Still Stuck @ Boot Loader - time to send for repair?

Hi all,
I'm writing just because i think now is time to send my TyTN for repair, but I want other infos if someone can help.
Today, after I've charged all the night (about 6 hours) my TyTN, when i've pushed power button it started with Boot Loader.
I thought well, it's time to upgrade the ROM, i've already saw this screen experimenting on functions but, to me sounds strange that the device started automatically in Boot Loader.
The ROM was ROM version 1.18.258.2 ROM date 07/22/06
I've downloaded a new (official) release ROM version 2.11.258.1
ROM date 03/07/07 and followed the instructions with Active Sync but obviously it dont started.
Searched and found how to upgrade with MiniSD and HERMIMG.nbh.
Successfully loaded the new ROM and device still restart in Boot Loader.
I've then connected to the wall plug and done an Hard Reset, Windows Mobile showed up right.
When the installation for EXTRAs ended the device restarted and NOW STILL in BOOT LOADER mode.
I've readed and tried everything on stuck Boot Loader and other topics but cant get out.
The thing that is very strange to me, is that I'm unable to use mtty or get connected to use uni_exitbootloader.
Another thing is that the device no more charge the battery or Amber lights on, only RED light with USB cable or Charger.
(Problem 6 @ http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems#other)
Finally I think is something USB hardware related and I'll send it for repair but just want to know if there something else I can try.
(maybe is better I post here? DEAD Hermes @ http://forum.xda-developers.com/showthread.php?t=286755)
Thanks in advance for any infos anyone can provide.
Marco.
Finally
I've tried with solution found on
http://michael-channon.spaces.live...._c=BlogPart&partqs=cat=Hermes+Charging+Issues
additional power batteries self made pack of 3 AAA Batteries worked for now.

O2 XDA Exec (Universal) Won't Power On after Unccessfull ROM Upgrade

--------------------------------------------------------------------------------
Hi...
I was trying to Upgrade my O2 XDA Exec Rom with Windows Mobile 6.5 by explode. The process went successfully till 99% and after that it ended up with Error. Then I unplugged my pda from the pc and tried to restart the device. I was surprised that the device did not respond to any of the following
Soft Reset
Hard Rest
Boot Loader mode Start (Bulb + Power + Reset)
It is totally blank screen whatever you do.
When I connected the device to the pc with usb cable, a Red Light is shown for 2 seconds and then goes off and a message comes up on the pc that "USB DEVICE NOT RECOGNIZED".
Then I tried to Remove battery from the device for a whole night and the next day morning i did all the above procedures again to get no results.
Kindly Help me out
Thanks
Dinesh Kumaar
dineshkumaar said:
--------------------------------------------------------------------------------
Hi...
I was trying to Upgrade my O2 XDA Exec Rom with Windows Mobile 6.5 by explode. The process went successfully till 99% and after that it ended up with Error. Then I unplugged my pda from the pc and tried to restart the device. I was surprised that the device did not respond to any of the following
Soft Reset
Hard Rest
Boot Loader mode Start (Bulb + Power + Reset)
It is totally blank screen whatever you do.
When I connected the device to the pc with usb cable, a Red Light is shown for 2 seconds and then goes off and a message comes up on the pc that "USB DEVICE NOT RECOGNIZED".
Then I tried to Remove battery from the device for a whole night and the next day morning i did all the above procedures again to get no results.
Kindly Help me out
Thanks
Dinesh Kumaar
Click to expand...
Click to collapse
Try to reflash with another ROM
And maybe your battery is not working
Good luck and donĀ“t forget to vote!
Im new to this forum and spending a few weeks doing searches I have found a new world of things I can do with my M5000! Only problem is I have the same problem as this guy. The problem started with no GSM, No Protocol version and no IMEI number, After countless rom installs and failed all I thought I left the sim in? Took batt out, No sim, Put the batt back in and now it wont turn on or do anything.
Has anyone found a solution to this problem or its it an expensive paper weight?? Im lost without it!
ronnie5 said:
Im new to this forum and spending a few weeks doing searches I have found a new world of things I can do with my M5000! Only problem is I have the same problem as this guy. The problem started with no GSM, No Protocol version and no IMEI number, After countless rom installs and failed all I thought I left the sim in? Took batt out, No sim, Put the batt back in and now it wont turn on or do anything.
Has anyone found a solution to this problem or its it an expensive paper weight?? Im lost without it!
Click to expand...
Click to collapse
Welcome to the forum
You have a great device!
Have a look here:
http://forum.xda-developers.com/showthread.php?p=3999833#post3999833
Hope it helps and good luck,

HD stays at smart mobility

I have a serious problem.
I have dutty's latest windows 6.5 rom. 2 weeks ago the touch hd did not restart after a soft reset. It starts, and stays at the "smart mobility" screen. It did nothing, only staying at the screen. Even after many soft resets it had the same problem. I went to the bootloader mode, and re-installed the rom with the usb.
After two weeks i have now the same problem. The device hangs at the smart mobility screen, and does nothing. But since last week i couldnt connect my device via usb. Also in bootloader it stays at serial. I used another usb cable, but that is not the problem. My PC does not see the device in any way.
I guess i can install a new rom with the micro sd card. But is this problem a software problem, or is this just a failing device?
(sorry for my bad english)
My question:

[Q] BLINKING SAMSUNG LOGO

Hi,
My phone was working absolutely normal for about a year but suddenly yesterday morning I found it stuck on 'BLINKING SAMSUNG LOGO'. I left it on charge overnight. It was absolutely shocking and I did everything possible to wake it up but It didnt show up. I did Hard Reset a multiple times, tried to unplug USB cable, battery back and forth, but it was of no help.
I found this question on various forums but unfortunately, no one came up with a positive solution except replacing it under warranty. I came back to Pakistan and phone is it out of warranty so there is no possibility for that.
Yesterday, I performed STOCK ROM flash. Luckily I managed to put it WP 7 and so far it is working fine. Later I updated it through ZUNE and during a hour download/installation, I expected it to install WP 7.5 but it popped up the same logo again. I tried everything but problem remains the same. Im stuck on 8th step out of 9 i.e. restarting your phone. I flashed back again to 7, then tried again, but same logo appears back and blinks
It clearly seems like wp 7.5 has some software issues in the bootup. Is there any direct WP 7.5 ROM available on internet?
What else should I do to fix it?
MicroSD Card
Ramzoun said:
Hi,
My phone was working absolutely normal for about a year but suddenly yesterday morning I found it stuck on 'BLINKING SAMSUNG LOGO'. I left it on charge overnight. It was absolutely shocking and I did everything possible to wake it up but It didnt show up. I did Hard Reset a multiple times, tried to unplug USB cable, battery back and forth, but it was of no help.
I found this question on various forums but unfortunately, no one came up with a positive solution except replacing it under warranty. I came back to Pakistan and phone is it out of warranty so there is no possibility for that.
Yesterday, I performed STOCK ROM flash. Luckily I managed to put it WP 7 and so far it is working fine. Later I updated it through ZUNE and during a hour download/installation, I expected it to install WP 7.5 but it popped up the same logo again. I tried everything but problem remains the same. Im stuck on 8th step out of 9 i.e. restarting your phone. I flashed back again to 7, then tried again, but same logo appears back and blinks
It clearly seems like wp 7.5 has some software issues in the bootup. Is there any direct WP 7.5 ROM available on internet?
What else should I do to fix it?
Click to expand...
Click to collapse
Hi, if you have a microsd card installed it may be the problem, remove the card, do a hardreset, then reflash your handset and try to upgrade to Mango then see what happens, if all is good then your microsd is faulty, this happened to a lot of focus users ))
Doesnt load wp.7.5 mango
VSparxx said:
Hi, if you have a microsd card installed it may be the problem, remove the card, do a hardreset, then reflash your handset and try to upgrade to Mango then see what happens, if all is good then your microsd is faulty, this happened to a lot of focus users ))
Click to expand...
Click to collapse
I actually removed my SD card since beginning installation. Any other possibility?
7.8 ROM
Should I try to update a 7.8 ROM over this 7.0.7004 OS Version??
You can tray
Ramzoun said:
Should I try to update a 7.8 ROM over this 7.0.7004 OS Version??
Click to expand...
Click to collapse
You will ned to install a custom bootloader for installing a custom ROM, but if you handset is under warranty I would fully recommend taking it to the service as I doubt your problem will magically disappear with a custom ROM, and there is a big chance of bricking the device when installing a custom bootloader if your device is problematic.
Please somebody help!
I have updated it twice but the problem pops up same in the end. It keeps on blinking the logo.
My current version is 7.0.7008. everytime I connect it to zune, it updates on request to 7.5 add on but Im stuck.
Please somebody help me, I have bought a used phone and out of warranty. What can I do to restore it back to WP 7.5.?
Ramzoun said:
I have updated it twice but the problem pops up same in the end. It keeps on blinking the logo.
My current version is 7.0.7008. everytime I connect it to zune, it updates on request to 7.5 add on but Im stuck.
Please somebody help me, I have bought a used phone and out of warranty. What can I do to restore it back to WP 7.5.?
Click to expand...
Click to collapse
What logo does it blink ? The Samsung one or the pc connection ?
OP, Sir next time title your thread Thanks, I did it for you...

Categories

Resources