Related
Hey Guys,
Well, I'm a bit gutted really! I dropped my XDA Mini S on the floor with the charger in and the connector IN the phone has come apart from inside the phone. The little metal bit is practically hanging out. I'm wondering, if i were to take the phone apart could i re-connect the little part? (I have a soldering iron if thats as simple as its going to be?)
Just wondering if anyone had any guides on how to take the phone apart and take a look at whats wrong?
Any help would be so much appreciated!
Many Thanks,
Tom
The service manual is hosted on the ftp site.
ftp://ftp.xda-developers.com/Wizard/Docs_Tutorials/
Hope this helps.
I suspect you probably broke the socket off, but if you have a soldering iron, you might as well try to get a new mini USB connector to work with.
You might try Pocket PC Techs:
http://www.pocketpctechs.com/main~unit~UTStarcom_XV6700-554~area~repairs~item~REP-USBCON01~name~UTStarcom+XV6700+Mini+USB+Connector+Replacement+Service.htm
I rang them up about an issue I had (screen on the fritz) and they seemed pretty knowledgeable and helpful.
Alternatively there's a company I found today in the UK. I can't vouch if they're good or not.
http://www.xdarepairs.co.uk/home.asp
Good luck.
Well I also have an issue with my wizzard... the mini jack connector (of the handsfree) is a bit loose.
What I am saying is that it does have a good connection with the rest of the circuit and sometimes the sound of the speaker goes off, then I have to insert the habdsfree and tickle it a little bit until it has a good contact.
? have some basic soldering experience,do you think I should give it a try?
Given my device has been apart too many times for me to admit to I thought I'd crack it open to take a pic for you guys. Not sure if this pic will help for those wanting to do some soldering:
Very large pic: http://farm1.static.flickr.com/216/452691530_f47801708f_o.jpg
Excuse the dust.
Ah! That picture at the bottom is exactly what I needed. The metal but at the bottom (the big sqaure) has totally sheared off....bloody thing. Thanks so much for the info on the repair guides. I may give those repair guys a call if i can't get it to work myself.
Thanks alot you guys
As for you WizeMan, it all depends on if you wish to void your warrenty or not. At the end of the day, I installed WM6 on my device so O2 would give me the finger if i tryed to claim. If I'm honest, I'm getting an upgrade next month so I'm not to bothered if I balls it up! Would be nice if I got it working though....
Lemmie know how you get on
unlock k-jam
i read all your write about how to unlock k-jam device but after all i get this message:
Lock Status: 0000000000000000
SIMLock Code: █⌠═eי∟80Γ█Σ☻< δ♠
how can i get it from this .........
lironasseo said:
i read all your write about how to unlock k-jam device but after all i get this message:
Lock Status: 0000000000000000
SIMLock Code: █⌠═eי∟80Γ█Σ☻< δ♠
how can i get it from this .........
Click to expand...
Click to collapse
A little bit of a thread hijack but that means it is SIM unlocked.
Let me tell you my news, my friends.
I opened my Qtek 9100 and fixed two serious issues regarding this phone, using... sponge (the one we use to wash the dishes)
1. I put some into the stylus socket (from the thin space it has) and also
2. On the top of the mini jack socket so when i assembled the housing it blocked it from moving (2 of the contacts are no more soldered and i dint have a soldering iron at that time)
Anyway, both operation went ok and my phone is more than fully functioning. Now the stylus is hardly (in a good way) comming out (it first gets longer then comes out).
I wanted to do also the safe singal fix, but didnt find the photos to apply it correclty, so if someone has them, please give link. If you need any info about the "Sponge" Hacks, just post or pm
WizeMan said:
Let me tell you my news, my friends.
I opened my Qtek 9100 and fixed two serious issues regarding this phone, using... sponge (the one we use to wash the dishes)
1. I put some into the stylus socket (from the thin space it has) and also
2. On the top of the mini jack socket so when i assembled the housing it blocked it from moving (2 of the contacts are no more soldered and i dint have a soldering iron at that time)
Anyway, both operation went ok and my phone is more than fully functioning. Now the stylus is hardly (in a good way) comming out (it first gets longer then comes out).
I wanted to do also the safe singal fix, but didnt find the photos to apply it correclty, so if someone has them, please give link. If you need any info about the "Sponge" Hacks, just post or pm
Click to expand...
Click to collapse
I'm still trying to get the a new fascia and will probably shove an eraser bit into the stylus spring mechanism to ensure the defect never happens. Also how did you discover the break in the solder joints on the headphones jack? I have a funny situation where the left channel of the headphones doesn't work but I suspected the headphones (the plug has to be pulled at an angle to get any sound out of the left) but now I am thinking it may be the socket itself.
By the way the reception fix pic doesn't load for me either but I unless you truly need it, don't waste your time doing it; I always have all 4 bars and sometimes have 2 bars.
AsGF2MX said:
I'm still trying to get the a new fascia and will probably shove an eraser bit into the stylus spring mechanism to ensure the defect never happens. Also how did you discover the break in the solder joints on the headphones jack? I have a funny situation where the left channel of the headphones doesn't work but I suspected the headphones (the plug has to be pulled at an angle to get any sound out of the left) but now I am thinking it may be the socket itself.
By the way the reception fix pic doesn't load for me either but I unless you truly need it, don't waste your time doing it; I always have all 4 bars and sometimes have 2 bars.
Click to expand...
Click to collapse
Allright here is the deal.
1. I found out the break in the soldier joints when i opened it. I was really suspicious about it because when i inserted my headphone jack into the connector, i had problem with the contact; the connector was loose and it muted my phones speaker. When i disassembled the phone using the service manual i saw with my eyes that the the joins where f-ed up.
2. I dont really need the signal hack i just wanted to experiment, i have 2.25.11 cingular radio rom and its great.
Btw i suppose you should better use the sponge, because the rubber may wear off but not the sponge...
Thanks for the tip on the sponge. I am going to grab a used but allegedly "like new" body from eBay and also get one of those covers as well.
Hi everyone,
Tonight my Dopod D810 developed a 'rattle'.
When it rings and vibrates or even when I shake the phone lightly, I can hear something small rattling around inside like perhaps a small piece of plastic.
Taking the battery cover off and battery out did not help, it seems to be behind that and near the top of the phone around the lens/speaker area....
Any ideas on what I should do? Although I may have to, I'm reluctant to take it to a '3' store here in Melbourne, knowing that they will probably send it away for maintenance and I'll have to do without a phone for weeks.
Any advice would be appreciated
Thanks in advance,
BB.
I don't know about '3' but I think many phone stores can lend you a spare phone during the maintenance period.
Of course, that phone may not be as fancy as your trinity, but I think in this situation, any working phone would do.
there really isnt much that can come loose there. there is a small posidrive screw thats sunk into a plastic channel that could rattle if it came loose, and the vibrator motor is there as well so i guess it could have worked its way loose. depending how confident you are you could take the back off and have a look, just have to deal with that pesky warranty void sticker (and lay your hands on a set of small torx drivers)
thanks all - i don't want to void the warranty so early so i might just take it into '3' and get them to look at it....
Also, around the same time, the camera buttons has become difficult to push. It still has the tactile response of being pushed but it now does nothing.
I cannot launch the camera by pressing this button, nor can I take any photos now! Due to the hardware key not working, there is no soft-key method to take photos
Agree that you should take it back to the store as you don't want to loose your warranty.
If you did feal brave, this good post might help
http://forum.xda-developers.com/showthread.php?t=311463
screw loose
had the same prob. Opened my p3600 and had to refit one srew which had loosened itself. It even got stuck in the vibrating engine.
i did void my warranty though...
Thanks reb - did your camera button also stop working?
Mine was a screw that became lose from the speaker phone, quick fix no point of sending it in for repair. Wll i didnt
Hey BlackBeauty how did you get on with this? Mine has developed the same rattle noise. It started after the phone vibrated from a call coming in.
Have you opened yours up?
I sent my Trinity back to HTC to get fixed. I still have 9 months on the warranty and didn't want to void it. Must have been a loose screw as that was HTC's response. Sent it away on Monday and got it back today (Friday) good as new!
Hello everyone..I recently replace the lcd for my niki htc...I bought the screen from ebay for $35 (plus shipping). Everything works fine but sometimes when i slide the phone the screen is wably or it looks like something is not connected and it moves but when i close it and i restart it again. it's fine or if i let it for awhile like that (so it goes on and off). So my question is...Is it the manufacture that made the screen, or is it something that it hasn't been connected right?
The other question is that my digitizer is broken in the up left corner and im thinking to replace it does any one can tell me how to take of the digitizer. i have found this website :http://www.pdacenter.ru/razborka/razbor_htc_touch_dual/ but it stops at the screen it doesn't tell you about the digitizer.
And the 3rd question is about that little piece it has fallen from somewhere while i dismantling my phone, i took a picture of it so someone can tell me what it is and where it goes.
Thank you very much for looking, and sorry for the noob questions first timer dismantling a phone and i loved IT!!!
You may wana have a look at the service manual, wich can be found here:
http://www.mikechannon.net/page1.html
It says that you can not disassemble it without replacing the speaker!
When you remove the speaker you need a new one. (or at least this is how I understood it
Maybe that part is the door for the MicroSD Card slot?
no i opened the cellphone 6 to 7 times so far. all you have to do is to unscrew the small screw that keeps the speaker in place so you can have more space to work with it.
all you have to do is to take off the digitiser where it gets connected. take the screen off. and raise the little black strip where the digitizer stripwires come out and push out the digitizer. it feels liked it doesn't go out but if you push it carefully it will. they have glue it with some kind of glue that it doesn't come off the digitizer but it stays on the cellphone so you can put in place your new digitizer...
If anybody needs help... pm me or leave a reply in this thread.
speaker rubber perhaps?
I just replaced my digitizer today (bought the handset from ebay - faulty touch screen). The little rubber that covers the speaker fell out in my hand when I was dismantling mine, so maybe thats what it is (looks similair).
Oh a quick question - after replacing my digitizer, my touch screen still doesnt work, even after hard reset - when asking to 'tap screen to set up device' it wont respond to any taps. Any ideas ?
fubofo said:
speaker rubber perhaps?
I just replaced my digitizer today (bought the handset from ebay - faulty touch screen). The little rubber that covers the speaker fell out in my hand when I was dismantling mine, so maybe thats what it is (looks similair).
Oh a quick question - after replacing my digitizer, my touch screen still doesnt work, even after hard reset - when asking to 'tap screen to set up device' it wont respond to any taps. Any ideas ?
Click to expand...
Click to collapse
my friend i think you have a bad digitizer, some people on ebay send defective digitizer and especially when they are from china they don't really care about sending a good one.... I had to send mine back 3 times!!!! i just got the last one 3 days ago and it took me at least a month and a half to send me a working one...If you pay with paypal...Tell the ebay user to send you a good one...Do not!! Do not!! send feedback until you got a good digitizer....Mostly it has to do with the connectors i guess where the digitizer connects.... Tell them that you need a new one and you can't wait for very long...tell them this is a customers cellphone and you need to have it fixed as soon as possible.. If they don't want to exchange for a new one dispute the payment!!! Don't wait too long...Do it Asap... As i told you there lots of defective digitizers....I had reset mine also but nothing happens i believe this is mostly hardware problem...If you have any questions about how to dismantle ask me... I have open my cellphone over 10 times cause of the digitizer
Thanks Nikos, Im fine with opening these devices they are easy enough to work with.
I purchased a digitizer for a Polaris not long ago and it worked perfect. Im gonna take the Nike apart tonight again and adjust/fiddle with the connections to make sure - I dont want to wait another 2 weeks for a replacement digitizer and pay for postage lol.
But i guess if it doesnt work tonight I will have to 'grin and bear it' and send it back
Just built in a replacement digitizer. Everything works quite well, some inaccuracies in the lower parts of the touch screen, but it works.
I managed to leave over a screw. And a barely visible stain between the Digitizer and the LCD.
But at least it is working again as a replacement phone and for testing various stuff...
btw, now knowing the phone from inside, that part could be the "door" between the SIM slot and battery. or the rubber part that directs sound to the microphone on the bottom front PCB.
cheers
I have just got my replacement digitizer in the mail 2day from Hong Kong and installed it just now, all is working perfectly as new again. I did a hard reset when the touch screen was first playing up, so I have lost all my themes, settings etc but luckily my office docs etc are still intact.
Anyhow, I made a video on how to replace the touch screen, its only quick as I did not go from the disasembly part, as there is already videos and tutorials on this, so I just documented on the actual digitizer replacement, which is actually basic 2-5mins work, but I thought a vid would be good for any noobs needing it in the future.
Once I edit it all up I will post the video here.
If anyone needs help on replacing the digitizer just ask. DON'T be tricked into buying the LCD + Digitizer if you only need the touch screen, as it is very easy to do without the lcd, though some ppl disagree.
Thanks for reading, thread will be updatd with Vid asap.
Hi X86
I have a crack on the upper plastic case, thats prob. why I have dirt showing on screen. In your opinion where is it located and can I clean it ?
It seems as if (if the crack is on the actual original housing, not just a add-on case) that dirt/dust has fallen down inbetween the digitizer and the LCD, so you can see it through the touchscreen right?
This is fairly simple to fix, you will either need to patch up the crack with silicone or something (best from the inside so it does'nt look messy) OR buy yourself a whole nw housing which cost about US15-$20.
Then just pull your elf/in apart and use cotton tips and wipes to thoroughly clean the LCD and insides.
If you need any help, just let me know via PM or here.
?Good Luck!
Thanks
That was my feeling, now I just need courage to take apart the casing (either repair or replace )
Thanks for bringing up this issue in the forum and extending your hand to others.
I appreciate it alot.
Hi x86
I have read the sticky for disassembling the elf. Can you tell me if it's necessary to unscrew anything and remove the rear speaker in order to remove the front panel ?
Edit: I think I found the answer in the next pics, the 4 screws attach to the front panel, right ?
Hi, i've just entered the world of winmo. i've recently wrecked my Elfin. But i can't seem to figured it out whether it's the LCD or the digitizer is broken...
1) my Elfin's screen turns to white with a few red and black stripes on the lower left corner, it doesn't react to any touch gesture.
2) i can still activesync the device and seems that my SD card is still working, i could copy out my PIMcontacts...thank goodness
3) the alarm still rings the next morning, i assume my device is still operating, of course now i've taken out the battery.
4) i've ask the phone shop for repair enquiries and they said that the replacement parts are not for retail selling in my country, Malaysia... so it needs to send back my Elfin to OEM and takes about 3 weeks time and cost around USD $ 130 bucks....
5) my friends told me it wasn't worth it, thus i was thinking of looking for help online and finally i found this thread...
6) can anyone offer few pieces of info? i thank you 1st.
bjonmy said:
Hi, i've just entered the world of winmo. i've recently wrecked my Elfin. But i can't seem to figured it out whether it's the LCD or the digitizer is broken...
1) my Elfin's screen turns to white with a few red and black stripes on the lower left corner, it doesn't react to any touch gesture.
2) i can still activesync the device and seems that my SD card is still working, i could copy out my PIMcontacts...thank goodness
3) the alarm still rings the next morning, i assume my device is still operating, of course now i've taken out the battery.
4) i've ask the phone shop for repair enquiries and they said that the replacement parts are not for retail selling in my country, Malaysia... so it needs to send back my Elfin to OEM and takes about 3 weeks time and cost around USD $ 130 bucks....
5) my friends told me it wasn't worth it, thus i was thinking of looking for help online and finally i found this thread...
6) can anyone offer few pieces of info? i thank you 1st.
Click to expand...
Click to collapse
That sounds like both a Digitizer and LCD issue.
Red and white strips is caused by the screen, while the phone not sensing your fingers is caused by digitizer.
But you still managed to use something like mymobiler to rescue your stuff right?
Yeah, you're in Malaysia right? In Singapore, to get this items, we have to get it off ebay or dealextreme.com.
But be careful with this, it void warrenty.
If you send it to HTC service centre, it may cost $160> Singapore dollars.
Cheers,
Jeremy
Hello! could people please share tips and things to remember when buying a used universal? I mean what are the things that you should do to check or find tell tale signs of defect, hardware, the firmware the os, I have already done a search in the forums and already know some, but there might be things that I have missed, so help would be very nice, I will be meeting the seller so I get to inspect the device up close so it would be nice to armed with the info how to inspect the device from how to check the bootload etc.
Thanks for the help and I hope that this helps others too
The Universal can be bought cheap at german eBay. Look for MDA PRO. You should be able to purchase one for around or less than 100 Euro.
Preferably look for the following signs:
1) Unmodded. Many users got the Universal within a contract from the operator, but did not use it much, because it is too big for them. Such Universals are normally in good condition. When advertised that it ships with an OS different than WM5, you know that the owner has been flashing it. I personally don't like that, because that means it belonged to a power user and must be more worn out.
2) Warranty stickers. Make sure the hinges have the warranty stickers inside. If they are missing, the device has been opened. You don't want to purchase one that has been opened.
3) Screen. Screen should be without scratches and should have had always a screen protector.
4) Speaker. The external speaker which is used for calls can break, as it is fitted with some kind of pogo pins. Make sure it is working.
If you get to test the device first, do as this:
- do a call (bring your SIM card)
- check WLAN and Bluetooth (bring a headphone and try it somewhere with WLAN activity)
- bring a SD card and see if it is read
- check for bad pixels
- play a song
- take a picture
- try the keyboard and touch screen
- try all the buttons
If everything works, that is the best you can check it for.
Of course it could break the next day, but it shouldn't.
Cheers,
vma
Great guide vma!
I´ll just add:
Take special care on the swivel piece (The one that gives Uni it´s great and unbeatable form factor: PDA - Micro Lap top)
take care of another thing when i bouted my universal after i used it for about 1 week the phone was hangs soo much the reason was in the memory crd .....so you must try a memory crd and play a small video on it about 10 minutes
The most important thing everyone forgot to mention is USB port. When looking for a device, see if the port moves in any way or wiggles in its opening. See if the device synchronises with AS, charges etc.
The fact the device had been flashed or opened wouldn't play a huge part for me if everything else works well and the body is in sound condition, e.g. the hinge is not loose, the screen rotates and closes properly, all keys are present and work, keyboard backlight works with and without sensor etc.
Speakers don't just break, as post No2 claims (POGO PINS??), but it is good to check that phone is capable of making/receiving calls, you can hear the other party and the other party can hear you, can play music and earphone plug is in working condition/attached properly
Not reading SD or SIM card is a biggie, dim screen, lost touch sensitivity, scratched or damaged digitizer, worn out buttons - all obvious signs. You can open the back, remove the battery and SIM card and check for a small white blotting paper sticker covering the small mainboard pins under the SIM card, any change in color towards pink - do not buy.
@enigma1nz:
Shame on me, I did indeed forget the USB port!!! You should of course check both: charging and Active Sync connection. A broken USB connector is a mayor issue and hard to solder without proper equipment.
Regarding the speaker: I am speaking out of experience, as one faild on me. The speaker is like a small button and it has two contact plates. They are not pogo pins, but act like them. The speaker will be pressed by the case against two contact points on the PCB. What happens is that apparently some car-holders do too much pressure on the sides of the Universal casing, causing the speaker contacts to bend back and forth everytime the phone is placed or removed from the holder. After a few months the contact gets worse and worse until one of both plates brake off. Because they are so tiny, it is impossible to repair the speaker - believe me, I have tried. I ended up buying a new speaker cell at eBay.
Cheers,
vma
vma said:
@enigma1nz:
Shame on me, I did indeed forget the USB port!!! You should of course check both: charging and Active Sync connection. A broken USB connector is a mayor issue and hard to solder without proper equipment.
Regarding the speaker: I am speaking out of experience, as one faild on me. The speaker is like a small button and it has two contact plates. They are not pogo pins, but act like them. The speaker will be pressed by the case against two contact points on the PCB. What happens is that apparently some car-holders do too much pressure on the sides of the Universal casing, causing the speaker contacts to bend back and forth everytime the phone is placed or removed from the holder. After a few months the contact gets worse and worse until one of both plates brake off. Because they are so tiny, it is impossible to repair the speaker - believe me, I have tried. I ended up buying a new speaker cell at eBay.
Cheers,
vma
Click to expand...
Click to collapse
And believe me, I repair devices for a living. Thanks for the run-through, although I could give you the same. It happened to you, doesn't mean it happens often or it is a fault in design. I could give you a list of design faults in quite a few models of expensive cellphones on the market today, the mentioned speakers are not one of them.
I appreciate, the help people! any more inputs? I am happy that all the previous posts were, about how to inspect the device upfront and some other useful tips what to check other inputs will be highly appreciated
Battery can be also considered. Some are sold with good batery some with dead battery. It is not so expensive, but costs something. In general if battery shows less than 50% and devidce still works (even under load) that is a good sign.
Also as for the touch screen - the best test is to open note taker and try to paint something. The painted line must exactly follow the stylus movement if it jumps somewhere, then the touch sensitive layer is bad. I bouht such UNI on eBay (was described as perfect working order), had to replace the digitizer myself.
I do prefer buying not working UNI's on Ebay with good display. Once I bought not booting one - mtty job fixed that. Other time I bouht one where the display was still off - the flex cable popped out from connector. Etc....
Thanks for all the advice people! now, please welcome me to the HTC universal family, (well actually, I have a Dopod 900 but what the heck all are the same right?) your inputs had been essential, for me to get my new baby without any hitches I hope that nothing manifests after the one week assurance the seller gave me
Special thanks to enigma1nz for all the patience and help provided to me I asked her a lot of questions in the pm's but she answered in full detail
Now I have my own device so I will be flashing away, I hope without any problems. Again my thanks to the community hopefully there are more inputs for others who are thinking of buying their 2nd hand universal via meet ups
Excellent news! Congratulations!!! And welcome to the Uni family, of course. As you can see, we are one friendly bunch, all help and support will always be available. Have fun
Damn, I was hoping to do a very good Marlon Brando Godfather impersonation with 'Welcome to the family'
LOL
You started in the right direction!
to midnightsights : welcome
orb3000 said:
LOL
You started in the right direction!
Click to expand...
Click to collapse
No, sweetie, the right direction would be an Orb3000 impersonation and 'Welcome to the forums', but I was worried, being Orb2000, hehe, that I simply won't be able to compete with a more updated version
enigma1nz said:
No, sweetie, the right direction would be an Orb3000 impersonation and 'Welcome to the forums', but I was worried, being Orb2000, hehe, that I simply won't be able to compete with a more updated version
Click to expand...
Click to collapse
LOL.........
enigma1nz said:
No, sweetie, the right direction would be an Orb3000 impersonation and 'Welcome to the forums', but I was worried, being Orb2000, hehe, that I simply won't be able to compete with a more updated version
Click to expand...
Click to collapse
Thanks dear, you´re nice
you´ll be Orb4000!!!
Cheers and have a nice weekend,