I seek other 9502 ultimate owners and experts advice on the below:
Upon trying to connect to the internet using the GPRS functionality, I always receive the following error message:
“Cannot connect for an unknown reason. To check your connection settings and change them if needed, tap settings. If the problem continues, reset your mobile device according to your manufacturer’s documentation and try again”
I have tried the following steps:
- Reviewed the connection settings picked up by the Imate configurator upon first boot, they were correct.
- Tried to remove the SIM card and use it on my JAMin, the device connected smoothly (with the above same connection settings).
- Hard reseted the device, still it didn’t connect.
- Checked the Operator settings of my provider on the internet, they are the same ones loaded by the Imate Configurator
- Tried another SIM card, same thing
- Went to the service provider and changed the SIM card and got a new one, same error
I shall appreciate any assistance.
UPDATE
Finally!!!!
After installing the new WM 6.1, the device connected smoothly
.
From a 9502 owner
Hi, I have read your post and looked at my Ultimate to find anything obvious and I cannot. I am on O2 in the UK and used the configurator settings which worked fine. If there are any settngs you would like me to verify for you, let me know.
Oh! did you check the phone settings as well as the network connection settings, it's possible that a default in there does not tally with your provider (Goto the Wireless Manager and Tap MENU|PHONE SETTINGS).
Cheers
Eden
GPRS - Ultimate 9502
Thx for your reply.
I have tried every possible combination of Network / Band selection from the phone settings but it didn't work.
Imate have responded that it may be a ROM issue and that they are working on an new updated ROM to be available soon that will probably solve the problem.
Meanwhile i am trying to figure out some registery tweak that could fix the problem (trial and error)
WM 6.1 Link please
Can you please post the link to the WM 6.1 ROM that resolved your problem.
Thanks
iMate 9502 WM 6.1 ROM
http://forum.xda-developers.com/showthread.php?t=407336&referrerid=676710
Related
Hi,
I've got an Orange M500, upgraded with the Imate ROM 1.12.00WWE - ever since I upgraded the ROM, I can connect to my Orange GPRS service fine, however, if I disconnect then try to reconnect again, the connection fails. I have to turn on flight mode, then turn on the radio again in order to get GPRS access.
I've tried upgrading to Radio 1.13.00, but still no joy.
Any ideas?
Mine does that and I have the original ROM. A bit of a pain isn't it.
Here's the fix
This was originally posted by Peter for the imate JAM.
I just installed it and it's working like a charm.
1. Download the older version of caller-id from:
ftp://xda:[email protected]/BlueAngel/CAB_Files/Caller ID/IA_CallerID_1.20_WWE.CAB
and transfer it over to your device. Any directory is Ok. I used ActiveSync to put it into the My Documents folder.
2. Remove the file IA_CD-Startup.exe from \Windows\Startup on your device.
3. Rename iacontacts.dll to something else (e.g. old-iacontacts.dll). This file is in the \Windows directory of your device but is hidden. However you can rename it using your PC. Open Windows explorer, and navigate to Mobile Device>My PocketPC>Windows.
4. Rename displayCID.dll to something else (e.g. old-displayCID.dll). Access it via your PC the same as for the previous step.
5. Soft reset
6. Run the CAB file on the device - just tap on it.
7. Soft reset.
That should do it.
I have the same GPRS problem too. However, the link you provided just asked for the password to access that ftp. Hey, acs540, do you know the password or do you have that CAB file? Thanks in advance.
usernameassword is xda:xda
The fix in this post seems to refer to caller id!?! I too get the gprs connection problem and have made it better with different roms but not found a sure-fire fix.
If anyone has a patch that fixes this, please post it!
GPRS now working
Hi,
Finally I tried, or at least halfway, After I removed the CallerID everyone is talking about my Qtek9090 now works flawless regarding GPRS.
This is very interesting that Caller ID software makes GPRS not working
Anyway, now I can start and stop GPRS several times, I have now toggled it 10 times without any problem.
Before I had to reset/toggle radio to make it reconnect after a disconnect.
Thank you all that has investigated this problem!
One last thing, Do you really need CallerID? :roll:
Br
Lars
I don't use Caller_ID, but Photo Contacts Pro.
Did you also try to change GPRS slot (Class 8 or Class 10) in GPRS settings?
XShell said:
I don't use Caller_ID, but Photo Contacts Pro.
Did you also try to change GPRS slot (Class 8 or Class 10) in GPRS settings?
Click to expand...
Click to collapse
Well, yes, I have changed to Class8 (4R1T), default was (I belive) Class10
Br
Lars
I'm got yesterday Wireles LAN Card SDIO 802.11b.Problem is that i can't connect my Qtek 2020 with this card.Can somebody help me about this problem?Thanx
Have you installed the drivers on your device? The card should have come with a CD, if not go to the manufacturers site.
Can you detect any networks?
Please describe the problem more precisely, and maybe someone can guide you better then this.
I'm totaly new in this.I tryed to folow instructions in manua.I instailed all drivers that i have recived,but still i can not find network and i have one wireless in my house.My main problem is that i don't know how i can make set up in my Qtek 2020.Thankx for any sugestion
Ok, I never actually used a separate SD card, but I just finished setting up my home network last week so I'll try to give you some pointers until someone more knowledgeable comes along.
1) If everything was installed correctly, you should get a new icon, in settings or programs (depends on the card I think) for the Wireless utility.
There should be an option to turn it on and off, so make sure its on.
2) If you are not sure how your network is configured, or just don't want the hassle of manually setting up the device, download Hitchhiker.
http://www.kasuei.com/hitchhiker/ its a free app that will automatically configure WiFi and connect you to the network. You will need .NET CF2 installed for it to work.
Also you can see any networks that were detected in Start->Settings->Connections->Network cards. You can choose there which one to connect to or manually configure the settings.
Thank you mr.Levenum!!!!
I will download tomorow this progam and i will try to connect SD card with Qtek again.I hope that will working well.Thank you too much for your help. Best regards
Hi!
I followed all instructions,and i instaled drivers and utiluty from instal cd.Problem is that my Qtek can't find any avalible wireles network and i have one in at home.I put all correct parameters for this network,but still nothing.I also tryed with program"Hitchhicker",but problem is the same,hi can't find any network.Have you any sugestion what more i can try.Thank you
Try checking the settings on you router.
Is it set to broadcast SSID?
What standard is the WLAN card B / G ? And what standards does the router support?
Also it is possible that your router is set to a channel the WLAN card does not support (my router supports up to channel 14, but my Jamin only up to 11)
Try using a different channel.
Hey guys, fresh meat in this forum, not quite new to Windows Mobile but very new to using it in a PDA with phone capabilities. Quite Symbian guy and sort of getting myself used to WM6 - and in love with Hermes...
I have just done a successful installation of Schap's 4.31 WM6 Rom - which I think is freaking great - when trying to make the VoIP work, I managed to get username, password and settings from Truphone account out of my N95 but I am not 100% sure I have put the right data in the right fields, result is that VoIP will not work at all and when I try to access the VoIP Settings (in the connections tab) it'll come up with a message "An unexpected error has ocurred in VoIPSettings.exe. Select Quit and then restart this program, or select Details for more information". Obviously I've done it a few times.
Help is more than appreciated.
Excuse me for my bad English.
I had the same problem and I deleted the file with my SIP configuration and then no problem :
File to delete :
Windows\System\VoIP\Prov0SIPSettings (it is an hidden file)
I have make this on a P4550 device with Schap's Rom. Perhaps is it the same thing...
Thanks
Thanks for this ! it worked for me as well.
i have a spv c500 from orange uk to unlock i install active sync4.5 and conect fone to pc it was conected and build partnership but wen i run in fone HTCUnlock-CVS den device didnt explored and give some problem to explore den i delete partnership from pc and tried but fail to explore.but wen i next day i conected the fone to pc it didnt made any partnership and gives the following error
wat should i do for this any idea?
same problem
any one can solve it
waiting
i had the same problem but found these guides to help me.
http://shadowork.net/soubor/2005/09/20/activesync.via.bluetooth.pdf to help set up the active sync
and http://spod.cx/blog/unlocking_orange_spv_c500.shtml to unlock the phone.
mine was on orange uk and now is working fine on o2UK
hope this helps and thanks to those who wrote the guides
Just says "Action cancelled"
I need a T-Mobile backup phone and tried to unlock my Orange C500 with this software.
I just get a screen saying "Action cancelled".
Is the software no longer functional?
I turned of my Firewall (M$ & Peerguardian) and I was linked to Activesync.
Can anyone help?
I just dealt with a similar problem unlocking an unbranded smt5600 for AT&T
I was having all sorts of active sync issues - which likely are a result of either:
a) device's activesync client not initializing
fix) Hard reset your device - this will reinstall a fresh version of the local activesync client. At very least this will require you to set up a fresh partnership
b) device is having USB problems
fix) if you are running wm5+, make sure to go to start>settings>connections> USB to PC (or whatever it's called) and uncheck the "Enable advanced network functionality" box
c) might be a host problem...
fix) any number of things. You've already started on the right path by disabling the firewall. I've read about many problems from people trying this on Vista machines.
Hope you figure it out!
Still no luck but trying.
Thank you for the help.
I even tried entering the IP address into IE still with no luck
I will try it on someone else machine.
I have a UK Orange SPV C500, running
Windosw Mobile 2003 v4.21.1088(Build 14217)
Radio Version 0
Operator: 4.1.1.4
Manufacturer: 1.1.1.91
Microsoft: 4.21.14217.0
No idea how to hard reset or update to a newer version.
It worked
Okay, It worked.
I tried it again and it worked perfectly (with both firewalls on)
I can only assume the site was down the first few times I tried it.
I am now happily using my unlocked SPV C500
Once I get my new phone back I'll be interested in updating the firmware now.
Hi!
I have problem with cellular connection.
I've tried few roms:
http://forum.xda-developers.com/showthread.php?t=1356833
http://forum.xda-developers.com/showthread.php?t=953078
I can't connect to gsm network.
Connection Setup says that my carrier doesn't exist in database (Play, Poland).
I did input my apn settings manually, but it didn't work eather.
On Android and WM6.5 everything is working fine. Few months ago I've had BackToTheFuture 7720 rom - without problems as well.
I'm running out of options...
Check if there is an update to Connection Setup, otherwise you could try flashing an original WM 6.5 Rom and see if the problem persists.
I've installed WM6.5 - everything is working fine.
Connection Setup from marketplace - same story as before.
Any ideas?
gregory90 said:
I've installed WM6.5 - everything is working fine.
Connection Setup from marketplace - same story as before.
Any ideas?
Click to expand...
Click to collapse
There is a new connections database cab for connection setup at yuki/xbmod tweaks thread, but Play is not in the database. Must be a niche carrier. Find out if Play is a reseller of a larger carrier.
Actually there is Play in that database. It seems like Connection Setup can't detect proper network (I'm using Turbosim to remove simlock - could this be causing problem?).
Is there a way to tell Connection Setup what settings should it use? Or set this manually?