Database Users

help me!!!!! please i can`t start my P3300

anymore. :--(
Yesterday i^ve make a setup for the ext_rom but with a wrong update. It was been not for the Artemis..my fault.
Now i see only th et-mobile start screen and no more.
What can i do? Thanks in advance..

hmm, please flash your p3300 whith the original software with hope that it will be alive again. otherwise you can take an hardreset on your phone but i'm sure that there will not happened.
is your PDA an original fom HTC or from any other Provider?

it`s from t-mobile
and a hardreset doesn`t work and it`s not successful.
How can i flash it again...how i get usb connection to do it?

dr.moppi said:
and a hardreset doesn`t work and it`s not successful.
How can i flash it again...how i get usb connection to do it?
Click to expand...
Click to collapse
hello there!. i have the same problem, did you manage to get a usb connection? i can't flash it...

Try to get it into bootloader ( Read the Artemis wiki as to how to get into bootloader) and if you are successful then try flashing it with the t-mobile stock rom.

arvind09 said:
Try to get it into bootloader ( Read the Artemis wiki as to how to get into bootloader) and if you are successful then try flashing it with the t-mobile stock rom.
Click to expand...
Click to collapse
Please tell me how can i get the t-mobile stock rom or can you give me the link, thanks

Shipped ROM's in English - http://wiki.xda-developers.com/index.php?pagename=Artemis_Upgrades
To get into bootloader - hold down the record/voice command button (top left along the side of the phone) and use the stylus to press the recessed reset button on the lower left side of the phone (same side as the other boutton you hold down) Keep holding the record button as you hit and release the reset button, you will eventually see a screen with color bars on it. At this point you will be able to get a USB connection, but not an active sync. Try to start the ROM file when the phone is in this state and connected to your computer.
What is the original language/carrier for your phone?

MDA Compact III stops in T-mobile logo screen
I manage to enter bootloader and start flashing a ROM but I allways get a error: image file corrupted.
I think I need the original Dutch T-mobile ROM.
Anyone know where to find it?

Hi I have the same problem. I have the B&B3.7 and get stuck in the splash screen. I could enter to the bootloader mode and use some commands of the mtty.
I have my old rom, how may i load it to the pda? I have a SD and a tytn to load something in it.
Thanks!
Hernan

ftsv said:
I manage to enter bootloader and start flashing a ROM but I allways get a error: image file corrupted.
I think I need the original Dutch T-mobile ROM.
Anyone know where to find it?
Click to expand...
Click to collapse
run uspl first!!! you can then run installation from any provider of your choice.
http://forum.xda-developers.com/showthread.php?t=311403

USPL cannot be run if your phone is stuck into bootloader?
It starts counting, askts to copy the same information again several times, and get stuck at 50... how is this possible, anyone has the original HTC Dutch rom ? May be the WM5 also! Thanks!

same problem but with no display
i have done the same mistake
have tried to upgrade my T-MOBILE MDA COMPACT III(aka htc p3300) with the HTC TOUCH ROM
it started to upgrade and an error occured
then i have lost the display and all
when i connect it to my laptop using USB i hear a beep in my computer but active syn didnt find any device
i dont know what to do now..please help me it has to be recovered
there must be some way pls pls anyone help me to get my working phone back
will appreciate your concern
thanks
Regards
Faraz Feroz

well you have to get the original ROM for your device.. see their website.. it should be there for free. or try to get it from anyplace.. (the original rom)
and then flash it using SD Card flashing
info for flashing it by that are here:
http://wiki.xda-developers.com/index.php?pagename=Artemis_SD_Card_Flashing
hope it will work

y_bother said:
well you have to get the original ROM for your device.. see their website.. it should be there for free. or try to get it from anyplace.. (the original rom)
and then flash it using SD Card flashing
info for flashing it by that are here:
http://wiki.xda-developers.com/index.php?pagename=Artemis_SD_Card_Flashing
hope it will work
Click to expand...
Click to collapse
thanks Y_Brother
i have downloaded the new rom but it doesnt seem to work too

Urgent Help Needed Please! "No-Gsm" BRICKED?

i posted this in another thread but no one replied so thought this one mite be more busy.
i am new to all this and i stupidly went running into things and tryed to ROM upgrade my t-mobile MDA Vario II (HERM300), not knowing i had to CID unlock first, it has broke! when i boot it up i can not get passed the t-mobile splash screen and it also flashes "no-gsm". i have read many suggestions on fixing this but i have had no luck. i can get into the boot screen however and get the red green and blue stripes.
i have IPL 1.01 and SPL 1.04.
it will allow me to connect to my PC with USB but active-sync does not recognize i have connected the phone.
please help someone. i just need a way i can get this thing working again. if i could just get the phone into a state of use again that would be good.

please help, at least let me know if Ive got a chance of repairing it

i believe if you can get it in to bootloader mode you can flash back to original rom and start over

i thought that to but when i tryed the t-mobile rom it said "connection error" and also said it should be connected through active sync. but then agen it mite of been the wrong t-mobile rom but im sure it was for the vario ii. do you have a link to the one i should try please?

i downloaded the official UK shiping rom from t-mobile site and upgrading now through bootloader. will report on what happens.....

nope, keep getting "device not responding" or "connection error". any other sugestions?

i looked on here http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick and it says that i have to "Flash any type2 radio in NBF format. If that doesn’t work, flash the radio using HERMflasher" please could someone tell me how to do this, if this is the solution to my problem or if there is another way around this. thanks.

please help someone i realy need to fix my phone

Cool down....
what's ur radio version?
Also have u read this? http://wiki.xda-developers.com/index.php?pagename=Hermes_SimUnlock - TRY THIS FIRST, before attempting anything else...

ok, i have tryed that "sim and cid unlocker" and i beleve that you have to connect with active-sync because when i tryed it when i was in boot loader it said that it was not connected but it was. i will get my radio version now.
EDIT: my radio version is: 0107
EDIT2: also, here are some other numbers (which i dont know what they mean but mite be needed) which apear on boot-up t-mobile splash screen, in red letters/numers, just before "no-gsm" flashes on:
M 05
S 04
B 06
D 1.21

If you can get into the Bootloader (Rainbow Screen) you should be okay (Not a Brick)
Go download a Radio Rom from the wiki.
Enter Bootloader first, then connect to PC. Then flash the Radio Rom.
Edit, Also Read: http://forum.xda -developers.com /showthread.php?t=296722

berdinkerdickle said:
If you can get into the Bootloader (Rainbow Screen) you should be okay (Not a Brick)
Go download a Radio Rom from the wiki.
Enter Bootloader first, then connect to PC. Then flash the Radio Rom.
Edit, Also Read: http://forum.xda -developers.com /showthread.php?t=296722
Click to expand...
Click to collapse
ok, ill try that, does it need to be a perticular radio because im not super CID? for some reason the link will not work.

oooooo, it seems to be workin!!!!!!!!! im at...16%. ill report what happens after update finished

yes!!! it worked!! thank you very very much for your help!!!

Cincular 8525 stuck in Bootloader

I have a Cingular 8525 running WM5 that is stuck in bootloader screen. I have tried to soft and hard reset ... just boots back to the same screen, I can't turn it off once in the screen and when i sync via usb to the pc i get the message that the "usb device that is connected is malfunctioning" I have not done any upgrading at all and the phone worked perfectly right up till the time i powered it down and restarted into the bootloader screen.
Please can someone out there help me with this issue?

Zulu137 said:
I have a Cingular 8525 running WM5 that is stuck in bootloader screen. I have tried to soft and hard reset ... just boots back to the same screen, I can't turn it off once in the screen and when i sync via usb to the pc i get the message that the "usb device that is connected is malfunctioning" I have not done any upgrading at all and the phone worked perfectly right up till the time i powered it down and restarted into the bootloader screen.
Please can someone out there help me with this issue?
Click to expand...
Click to collapse
same problems, run perfect before with schaps wm6 rom then flash to faria wm6.1... not feel good with faria. try to flash with other rom then the problem start ..
how to recover ....... please help

Asfarizal said:
same problems, run perfect before with schaps wm6 rom then flash to faria wm6.1... not feel good with faria. try to flash with other rom then the problem start ..
how to recover ....... please help
Click to expand...
Click to collapse
Manage to solve the problem ...thanks WIKI !!
Go to Bootloader mode: Hold side OK and POWER buttons together and reset with stylus
Then Flash to any ROM you want !!

Thanks .... But
Thanks for the reply ... but i have no idea how to do what you tell me, I am new to all this phone "stuff" as a matter of fact this is the first time that i am ever using one of these forums. I have read till i am cross eyed but dont actually understand what you are talking about ... now don't let that scare you away as i am willing to learn and i am not braindead ... you all had to start sometime in this, not so. I get that i need to try and reflash my rom...
so is there some type of rom update software that i need? ... what is a hard SPL?? ... and who is Schaps?? .. sorry guys to do this to you but i would like to get into this game and i need some ( well maybe a lot ) of pointers.
Thanks for your time.

1. Search for "mr vanxs guide" so you have an idea on what you're doing.
2. OK, as Asfarizal said "Go to Bootloader mode: Hold side OK and POWER buttons together and reset with stylus". If you cant work out what the buttons are, go to the manual. it will tell you.
3. type in "hard SPL" in search on the forum & download the .zip or .rar file. this should have 2 files inside when opened,
a). RUUWrapper.exe and
b). RUU_signed.nbh
sync Hermes and double click .exe file. follow prompts.
4. find a rom that you want (would suggest TNT SE as a fairly good rom for noobs... good and stable, no problems...) Again download, then (and this is personel preference) format an sd card fat 32 and copy RUU_signed.nbh into root directory. Rename it Hermimg.nbh. Put into Phone and put into bootloader(make sure the battery is more than 50%) follow prompts. This should get you out of trouble. You can also sync your Phone and double click on the RUUWrapper.exe HOWEVER, if you should reset your computer, pull out the usb cable or have anything else happen to the computer that interrupts the flashm, you could end up with a worse brick than you have now. try to read up on flashing (search for "mr vanxs guide") and this should help you a lot if you have other questions. Good luck and happy flashing......

Thank You
I will follow the instructions you gave and try to get it going this weekend.
Thank you so much for your time

Zulu137 said:
Thanks for the reply ... but i have no idea how to do what you tell me, I am new to all this phone "stuff" as a matter of fact this is the first time that i am ever using one of these forums. I have read till i am cross eyed but dont actually understand what you are talking about ... now don't let that scare you away as i am willing to learn and i am not braindead ... you all had to start sometime in this, not so. I get that i need to try and reflash my rom...
so is there some type of rom update software that i need? ... what is a hard SPL?? ... and who is Schaps?? .. sorry guys to do this to you but i would like to get into this game and i need some ( well maybe a lot ) of pointers.
Thanks for your time.
Click to expand...
Click to collapse
Looks like you've got a lot of reading to do, and a problem to sort out. Firstly a couple of answers...
Schaps is a Rom Cooking guru (makes custom versions of WM5, WM6 etc). When you get your phone sorted out I'd recommend trying one of his roms.
Hard SPL. The SPL is part of the bootloader which effectively dictates how a rom is flashed and what roms can be flashed. HardSPL is a custom version of this which allows you to flash any rom from any carrier. It also protects against a bad flash in many cases. It is recommended before you try flashing any new roms or radio roms. Use Hard-SPL-V7 at the bottom of the first post here.
The Rom upgrading software is contained in any of the cooked or carrier supplied roms. It is normally a .zip file which cotains 2 files: xxxxxRUU.exe and RUU_signed.nbh. You run the .exe file from your PC when connected to your phone via USB. More details of how to do this are in MrVanx's guides. Also other resources here.
Now to try to sort your phone out...
What is displayed on your screen when in bootloader mode? It should be something like this:
HERM200
IPL-1.04
HERM200
SPL-2.10.Olipro (This is HardSPL V7)
If you don't have an Olipro SPL then you need to get HardSPL onto your phone. If you haven't done any upgrading and have had the phone from new then I guess you don't have hardSPL.
Now you need to fix your USB Malfunctioning problem. I can't help too much here except to suggest trying a different cable, different USB port or different PC. Also, if you are running Vista try an XP maxhine. When you connect to the PC does your phone show Serial or USB on the screen? If you can't get a USB connection, all is not lost - you can re-flash your rom using an SD card, method here.
There is a thread about un-bricking phones which may help.
There are various diagnostic tools (which can also screw your phone if used incorrectly). The favourite of these is MTTY but you need a USB connection to use this.
If your phone is in warranty I'd recommend getting your supplier to sort it out, but if not I'd try to re-flash an ORIGINAL supplier rom (Cingular I guess). You can get links to the official supplier roms here.
I think (might be wrong) that sometimes when stuck in bootloader you need to flash an official rom, not a cooked one to recover your phone - then you can run HardSPL and then flash cooked roms again.

Cingular 8525 stuck in bootloader
Thanks for the reply ... lots of great input.
Now to answer some of your questions.
1) When I power up the phone (only pushing the power button ) it goes straight into the bootloader screen without pushing any other buttons, and it displays
HERM100
IPL-1.01
HERM100
SPL-1.06
Then at the bottom in the white bar it says "Serial"
The only way that i have found to power it down again is to remove the battery, there is no response from any single buttons after it is in bootloader
the soft reset and hard reset work but it just goes right back to the bootloader screen after.
2) The USB malfunction. This only started after the phone "crashed" and before that it worked great ... well i only used it to sync up to my work pc for the contacts and to get pictures onto my hard drive.
all the PC's that i use are running XP. I have tried my home PC and my Laptop
and the work PC and all of them have their own cables and they all say the same thing ... "the USB device is malfunctioning"
I am sure that when i get the phone going again the USB will start to function again.
3) Phone warranty ... I bought the phone off e-bay from a store in new york about 10 months ago as a "new unlocked cingular 8525" it was new and unlocked, but i have no idea how they unlocked it. I would assume that there would be no warranty now and in any case i live in Canada and would have to ship it down to the states to an AT&T repair center and that sounds like a nightmare to me with the customs and so on.
I will give you a little more background on the problem. the phone worked like a charm without any problems at all for the 10 months that i had it, then the morning of the crash the phones alarm did not go off in the morning and i was almost late for work ... i did not pay it any further attention untill at 3:26pm
that afternoon the alarm went off ??????? (it was set for 6:05am) so i checked the main clock time, it was right. I then checked the alarm time, it was right ??? So i figured that something must have just got confused, so i powered down the phone with the power button to just restart it and while it was powered down i removed the battery to take the oportunity to to clean all those fuzzies and dust that collect in the battery compartment out and put it all together and powered it up again (just by pushing the power button) and this wierd red, green, blue and white screen appeared and that is all that i have seen since ???
I hope that answers your questions and i will start going through the links that you sent and get to reading ... will there be a pop quiz ... lol
Thanks again for your time and i very much appreciate all the time that all of you have spent on me and my phone ..... I know that you all just feel bad for me because i now have to use a Motorolla V551 ... lol

Great Work
ultramag69 said:
1. Search for "mr vanxs guide" so you have an idea on what you're doing.
2. OK, as Asfarizal said "Go to Bootloader mode: Hold side OK and POWER buttons together and reset with stylus". If you cant work out what the buttons are, go to the manual. it will tell you.
3. type in "hard SPL" in search on the forum & download the .zip or .rar file. this should have 2 files inside when opened,
a). RUUWrapper.exe and
b). RUU_signed.nbh
sync Hermes and double click .exe file. follow prompts.
4. find a rom that you want (would suggest TNT SE as a fairly good rom for noobs... good and stable, no problems...) Again download, then (and this is personel preference) format an sd card fat 32 and copy RUU_signed.nbh into root directory. Rename it Hermimg.nbh. Put into Phone and put into bootloader(make sure the battery is more than 50%) follow prompts. This should get you out of trouble. You can also sync your Phone and double click on the RUUWrapper.exe HOWEVER, if you should reset your computer, pull out the usb cable or have anything else happen to the computer that interrupts the flashm, you could end up with a worse brick than you have now. try to read up on flashing (search for "mr vanxs guide") and this should help you a lot if you have other questions. Good luck and happy flashing......
Click to expand...
Click to collapse
Thanks a lot man & great work i unbricked my Herm100 with method u mention above thanks a lot & great job keep it up

I also have this problem.
I d/l Hard-SPL-V7
and when i run RUUWrapper.exe
I get an error saying the application failed to initialize properly (0xc0000135)
What's going on?
How do i fix this?
this happened when i was trying to unlock the phone.
Thanks

need help
when i switch on my orange herm100 it shows On the bootloader screen is displayed:
HERM100
I PL-1.01
HERM100
SPL-1.40.01ipro
history : i buy unlocked orange phone
fewdays back i found no imei ,
yesterday i try to flash by micro sd but in gsm stage its gets hang no progress after extrom stage
IPL - OK
BOOTLOADER - OK
SPLASH1 - OK
SPLASH2 - OK
EXTROM - OK
GSM - (NO ACTION)
OS -
i tryed several time no action, i cant connect by mini usb.
PLEASE help me
tell me which it the right rom to chose? step by step procedure..
how to rectify imei?
thanks and regards
kirtibas

kirtibas, sorry it took so long to reply, 1st thing I'd do is upgrade to SPL 2.10 olipro. This is safer to use than others. then I'd suggest reflashing a stock rom to see if that works. After stock rom works then use a cooked rom as your heart desires... Cheers...

Having problems... Possible Brick :(

I've been reading through threads for almost 2 hours and I can't seem to find one direction to go in. I have the wing in bootloader mode now as it won't boot up normally anymore, just freezes at the 'T-mobile' screen. I know I need the original RUU but can not seem to find it. I'm interested in flashing it with one of the custom roms but am open to suggestions on the best ones. I've read over a few and they all have only slight differences to me unless I've read them wrong.
IPL 4.10.0002
SPL 4.10.0000
Any help will be greatly appreciated!

Furthermore, I have tried to flash it while in the bootloader mode with a few different files and I'm getting the same error every time. It makes it to about 3% and restarts the phone and the RUU reports that the image file is corrupt...
hopefully this will help.

epicphotoeye said:
Furthermore, I have tried to flash it while in the bootloader mode with a few different files and I'm getting the same error every time. It makes it to about 3% and restarts the phone and the RUU reports that the image file is corrupt...
hopefully this will help.
Click to expand...
Click to collapse
next time search. but i thought id be nice and search for you
http://forum.xda-developers.com/showthread.php?t=345411

Why thank you sir. Guess I wasn't using the right term... I looked for 'hearld ruu' and didn't think to use 'wing' either way it ended up working however I thought I'd add this little bit in for someone incase it happens to them.
right after running this program and starting the RUU, my phone reset at 1% but I immediately held down the camera button and put it back into bootloader mode and it seemed to continue right from where it left off...
Thanks again!

epicphotoeye said:
Why thank you sir. Guess I wasn't using the right term... I looked for 'hearld ruu' and didn't think to use 'wing' either way it ended up working however I thought I'd add this little bit in for someone incase it happens to them.
right after running this program and starting the RUU, my phone reset at 1% but I immediately held down the camera button and put it back into bootloader mode and it seemed to continue right from where it left off...
Thanks again!
Click to expand...
Click to collapse
and remememer to hard-spl before trying to flash any other rom!

[SOLVED] Connection Error [262]. Stuck in bootloader (tri color) mode.

I'm new in these forums as well I'm new with flashing ROMs so obviously I messed up flash process and my device stuck in bootloader (tri-color) mode. This post I address to those unfortunate like me .
# Symptoms #
- ROM flash started and stopped at 17%. After recovery flash process stucks at 0% and pops Connection Error 262. Device is stuck in bootloader mode not possible to flash anything, hard reset does not help, flash from SD card does not help either.
# Possible cause for that #
1. In bootloader mode device shows:
Code:
Pola100
SPL-1.25.0000
CPLD-2
means that Hard SPL was not flashed before flashing ROM file (if Hard SPL was flashed then in second line will be written SPL-2.20.Olinex.).
2. Connection between ActiveSync and device was not established when flashing ROM file.
Before to go any further please take your time and read Polaris Wiki to get familiar with glossary and acronyms used here.
PROCEED ONLY if flashing original ROM does not help, hard reset does not help and flash from SD card does not work.
# Solution #
1. Download MTTY software.
2. Kill ActiveSync (Press Ctrl-Alt-Del and stop rapimgr.exe and wcescomm.exe processes).
3. Plug Polaris into usb port (Plug directly not through hubs).
4. Start MTTY after chose USB from PORT dropdown list (if it is not listed there then ActiveSync processes were not stopped).
5. in window type: set 16 0 (enter cmd mode)
6. after type: task 8 (this will format phone)
7. after type: task 0 (this will restart phone. Not always necessary)
8. soft reset
This procedure can damage your phone. Use it as last resort.
Official source in french here.
Now before flashing any ROMs read carefully how to flash (not install!) Hard SPL.
# P.S. about install and flash termins #
This error with flashing happened to my due misunderstanding between notions of installing something on your device and flashing. In my opinion those are completely two different things. As for first I understand of running some cab or exe directly on device. So problem comes when people sees install Hard SPL en device as they try to find some cabs or exes to install directly on device or they just copy all files to device. To make things clear Hard SPL "installation" actually is ROM flash process which must be done with maximum caution, but those who did not read Wiki won't understand it.
Cheers, whitealien

BiG THX @ Whitealien.
works to 100% on my Touch Cruise.
I flashed under Vista Ultimate...
# Solution # ... addition from me for Vista users!
....
2. Start Windows Mobile Device Center and Deaktivate USB Connection and then start Task manager end kill
Process wmdc.exe.
Rest of whitealien. and have fun!

Thank you!!!!
I had given up on this, and was sure my only option was a warranty repair :O

always welcome

Thanks, you've saved my Polaris.
Mine didn't want to react anymore to the soft reset, so I replaced your instruction 8 with:
Cmd>boot
and that did the trick.

whitealien said:
1. In bootloader mode device shows:
Code:
Pola100
SPL-1.25.0000
CPLD-2
means that Hard SPL was not flashed before flashing ROM file (if Hard SPL was flashed then in second line will be written SPL-2.20.Olinex.).
Cheers, whitealien
Click to expand...
Click to collapse
I had exactly the same problem, for whatever reason went back to original SPL before HARD SPL.
I solved my issue by using back the original original HTC RUU_signed.nbh and flash it using the CustomRUU.
Thereafter, repeat the entire HARD SPL and flash the home cooked ROM.
Cheers.

For unbricking your HTC Polaris, you can try also a hard-reset (if it is related to a software error):
http://www.hardreset.eu/htc_touch_cruise_polaris_hard_reset_soft_reset.html

Thank you very much
you really helped
thank you again

mrfone2003 said:
Thank you very much
you really helped
thank you again
Click to expand...
Click to collapse
you are welcome.
Seems people are still falling for this error.

I'm has this error.
Solution (with SPL-2.20):
- kill ActiveSync (process, not uninstall)
- cable to USB on motherboard
- hard reset on phone
- connect to cable
- flash OFFICIAL rom
Two time I revive my Polaris.

help me please
hi.I have a big problem with my htc touch cruise when I installed a hard spl htc dedicate a Diamond.donc I had a white encrant after I did a hard reset since my htc no longer I have a black encrant are neither green nor orange but when I connect with the pc I am data interface and it does not recognized my htc. In my pay is not qualified repairman three non réparé.aidé unable to please me I tried the commands mtty.exe but does not c I do not really know how it works.
thank you for your patience and for help

thanks for the support
Thanks dudes for the great help you gave to recover my htc dual from bootloader screen. I am very happy to have my phone back. Thanks for everybody for the help they have provided generously. I appreciate alot. infact thousands times.

I think i have really messed up my phone. When opening mtty i select USB and press ok, then it says "can not open USB Port"
please help me, i have all the symptoms you explain. Stuck in bootloader, POLA200 SPL-1.25.0000 CPLD-2
i cant flash any roms and the original rom stops at 39%, i have redownloaded it countless times so its not the rom.

aaront1988 said:
I think i have really messed up my phone. When opening mtty i select USB and press ok, then it says "can not open USB Port"
please help me, i have all the symptoms you explain. Stuck in bootloader, POLA200 SPL-1.25.0000 CPLD-2
i cant flash any roms and the original rom stops at 39%, i have redownloaded it countless times so its not the rom.
Click to expand...
Click to collapse
Did you follow all steps from 1st post?
Did you kill all running ActiveSync processes?

I did indeed, i'm on vista so didnt have those particular processes going but followed the step from Aeroman and it still doesn't want to play. Any ideas?

managed to find a working XP machine and it worked a treat. Thank you so much.

thanks,this solved my pb

please help
Im having the same problem, im stuck in the bootloader but i didnt do anything for that to happen....this happened all alone withount any try to flash or do anything
it is saying
POLA100
SPL-1.28.0000
CPLD-2
when this happened i tried sodt reset and unpluging the battery b4 reading and searching here.
now i tried the steps showing in the first post and step by step .... the devise restart to the same bootloader like i did nothing ((( oh god im so upset please help me .... what to do ((((

wesram said:
Im having the same problem, im stuck in the bootloader but i didnt do anything for that to happen....this happened all alone withount any try to flash or do anything
it is saying
POLA100
SPL-1.28.0000
CPLD-2
when this happened i tried sodt reset and unpluging the battery b4 reading and searching here.
now i tried the steps showing in the first post and step by step .... the devise restart to the same bootloader like i did nothing ((( oh god im so upset please help me .... what to do ((((
Click to expand...
Click to collapse
What did you do to get there?

whitealien said:
What did you do to get there?
Click to expand...
Click to collapse
hey, im sorry for the late reply. it didnt notify me and now after posting several times asking for help in many threads by accident i bumped into this thread again to see that u answered and thank you so much.
now, what i did? this is the wierd thing, i didnt do anything, i went and back to see my phone stuck in bootload .... after this i tried almost everything i can find. from ur solution to flashing original rom to hrd spl to .........
now all gave an error except the original rom (polaris.1.28.415.2), it did went to 100% and device restarted to take me to my nightmare .... another bootloader screen am i suppose to search for polaris 1.28.0000?
i still have now the same writing shown.
please help me with this, its a nightmare .... is it totaly dead???
i managed to catch what it is saying b4 bootload screen (only when SD card is in place) it says no image file was found!!! in a very fast way and go to bootloader. in case the sd is not in place nothing happens and it goes straight to the bootloader