Database Users

My Qtek doens't pass the red, green, blue screen

Hello,
Well to explain my problem. I had the RUU_Prophet_2151327_21513121_021921_DOP_ASIA_WWE_Ship-NoVendorID flashed onto my O2 XDA Neo. No problems, but sometimes I couldn't go back to desktop because "programms" didn't want to close. So I went to look for a dutch firmware. I found one and tried it. It didn't work, but my XDA Neo was already at 1% and didn't go further. So I pulled the cable out of the telephone. Now it doens't pass the red, green, blue screen when starting the phone. Hard reset doens't help eather. Wenn I connect it to the computer, activesync says "not connected".
On the screen it says:
RUU
IPL 2.15.0001
SPL 2.15.0001
Please help me out, because I really don't know what to do anymore

Encountered your case before while trying to downgrade with no success.
I suggest you try to turn back to dopod wwe rom and install it again before further attempts to brick your device.
Active sync tells it's not connected, that's normal because you connect a device which has no rom now.
You should see "USB" at the bottom of the screen once connecting to PC. Then start the rom update.
It will try to discover what's in your pda and will report you "nothing", which is logic. Click update and go. It should proceed...
Good luck.

g3k said:
Encountered your case before while trying to downgrade with no success.
I suggest you try to turn back to dopod wwe rom and install it again before further attempts to brick your device.
Active sync tells it's not connected, that's normal because you connect a device which has no rom now.
You should see "USB" at the bottom of the screen once connecting to PC. Then start the rom update.
It will try to discover what's in your pda and will report you "nothing", which is logic. Click update and go. It should proceed...
Good luck.
Click to expand...
Click to collapse
Thank you so much! I reflashed my old rom, and the device works fine again. But is it not possible to run an older rom? I would like to have the dutch version.

If your device is Sim unlocked, you may try the famous specific rom availIable at:
http://en.pdamobiz.com/en/forum/forum_posts.asp?TID=437&PN=1&TPN=1
This rom is for downgrading in a first step and cid unlocking in the second step exclusively and not for continous use . Once these two task are done, you can install any ROM you want.
Reminder: You can not install other language without CID unlocking.

g3k said:
Reminder: You can not install other language without CID unlocking.
Click to expand...
Click to collapse
It is not true. You can install any language ROM using NoVendorID patched reflashing utility.

Yes and no!
If the ROM to write is never "patched rom update utility" will bypass the CID check step and continue to install.
But it the new rom is older (ie 2.09 to write over 2.13) problems start there and you get an error in most cases. In that case we need to downgrade.
I've faced and practiced both cases.

Thanks for details...

help me!!!!! please i can`t start my P3300

anymore. :--(
Yesterday i^ve make a setup for the ext_rom but with a wrong update. It was been not for the Artemis..my fault.
Now i see only th et-mobile start screen and no more.
What can i do? Thanks in advance..

hmm, please flash your p3300 whith the original software with hope that it will be alive again. otherwise you can take an hardreset on your phone but i'm sure that there will not happened.
is your PDA an original fom HTC or from any other Provider?

it`s from t-mobile
and a hardreset doesn`t work and it`s not successful.
How can i flash it again...how i get usb connection to do it?

dr.moppi said:
and a hardreset doesn`t work and it`s not successful.
How can i flash it again...how i get usb connection to do it?
Click to expand...
Click to collapse
hello there!. i have the same problem, did you manage to get a usb connection? i can't flash it...

Try to get it into bootloader ( Read the Artemis wiki as to how to get into bootloader) and if you are successful then try flashing it with the t-mobile stock rom.

arvind09 said:
Try to get it into bootloader ( Read the Artemis wiki as to how to get into bootloader) and if you are successful then try flashing it with the t-mobile stock rom.
Click to expand...
Click to collapse
Please tell me how can i get the t-mobile stock rom or can you give me the link, thanks

Shipped ROM's in English - http://wiki.xda-developers.com/index.php?pagename=Artemis_Upgrades
To get into bootloader - hold down the record/voice command button (top left along the side of the phone) and use the stylus to press the recessed reset button on the lower left side of the phone (same side as the other boutton you hold down) Keep holding the record button as you hit and release the reset button, you will eventually see a screen with color bars on it. At this point you will be able to get a USB connection, but not an active sync. Try to start the ROM file when the phone is in this state and connected to your computer.
What is the original language/carrier for your phone?

MDA Compact III stops in T-mobile logo screen
I manage to enter bootloader and start flashing a ROM but I allways get a error: image file corrupted.
I think I need the original Dutch T-mobile ROM.
Anyone know where to find it?

Hi I have the same problem. I have the B&B3.7 and get stuck in the splash screen. I could enter to the bootloader mode and use some commands of the mtty.
I have my old rom, how may i load it to the pda? I have a SD and a tytn to load something in it.
Thanks!
Hernan

ftsv said:
I manage to enter bootloader and start flashing a ROM but I allways get a error: image file corrupted.
I think I need the original Dutch T-mobile ROM.
Anyone know where to find it?
Click to expand...
Click to collapse
run uspl first!!! you can then run installation from any provider of your choice.
http://forum.xda-developers.com/showthread.php?t=311403

USPL cannot be run if your phone is stuck into bootloader?
It starts counting, askts to copy the same information again several times, and get stuck at 50... how is this possible, anyone has the original HTC Dutch rom ? May be the WM5 also! Thanks!

same problem but with no display
i have done the same mistake
have tried to upgrade my T-MOBILE MDA COMPACT III(aka htc p3300) with the HTC TOUCH ROM
it started to upgrade and an error occured
then i have lost the display and all
when i connect it to my laptop using USB i hear a beep in my computer but active syn didnt find any device
i dont know what to do now..please help me it has to be recovered
there must be some way pls pls anyone help me to get my working phone back
will appreciate your concern
thanks
Regards
Faraz Feroz

well you have to get the original ROM for your device.. see their website.. it should be there for free. or try to get it from anyplace.. (the original rom)
and then flash it using SD Card flashing
info for flashing it by that are here:
http://wiki.xda-developers.com/index.php?pagename=Artemis_SD_Card_Flashing
hope it will work

y_bother said:
well you have to get the original ROM for your device.. see their website.. it should be there for free. or try to get it from anyplace.. (the original rom)
and then flash it using SD Card flashing
info for flashing it by that are here:
http://wiki.xda-developers.com/index.php?pagename=Artemis_SD_Card_Flashing
hope it will work
Click to expand...
Click to collapse
thanks Y_Brother
i have downloaded the new rom but it doesnt seem to work too

Dead P3300 Artemis...

Hi,
Does anyone knows a method for repairing my old P3300.
The problem is i've tried to upgrade to wm6 and something went wrong,
ATM i only have a screen with the Tmobile logo,
I can open the bootloader, but if i load the bootloader and try to run the official rom update i get the error 122 cannot connect to device.
If i'm in the bootloader and try to start mtty, it all goes as it is supposed to go
I can see the phone in mtty and can get it into flash mode when i enter the bootloader password.
Even when the phone is in this mode the official upgrade won't see the device.
So my question: is there a way to flash/upgrade the rom from mtty?
If yes what are the commands for it in mtty.
If not does anybody know an other solution?
Btw it's a sim unlocked and Cid unlocked P3300 From the Netherlands Tmobile.
IPL 1.13.0001
SPL 1.13.0000
GSM 02.49.90
OS 3.4.0.0
Thanks
Janus

Same here, I think we need the original T-Mobile rom.

RaZoR X said:
Same here, I think we need the original T-Mobile rom.
Click to expand...
Click to collapse
sounds like you did't run the USPL before you burned your Rom, try and do a search on this in the forum, there are plenty of fixes to get your phones up and running again.
another tip, look at the wiki and download Tmobile UK/Ger version, that should do the trick at least to get your phone running, then make sure you do the USPL before you brick it again.

neilhhardy said:
sounds like you did't run the USPL before you burned your Rom, try and do a search on this in the forum, there are plenty of fixes to get your phones up and running again.
another tip, look at the wiki and download Tmobile UK/Ger version, that should do the trick at least to get your phone running, then make sure you do the USPL before you brick it again.
Click to expand...
Click to collapse
I did ran the USPL.
I took a look @ the wiki, but I think those files (all of them are less then 100k) are theme files.
"T-Mobile_NL_MDA_Compact_III_1.13.114.1_NLD_ExtROM"
IPL: 3.13.0001
SPL: 3.13.0000
The USB is working
With the "PDA Phone ROM Update Utility 3.6.3.1." from HTC I tried to get the MDA functional again.
In the Verify the ROM you want to update window it says this:
From:
Image version: -blank-
To
Image version 3.13.405.1
But after 2% sometimes 7%, it says this: "Error [244]:Invaild model ID".
So maybe the USPL didn't went well.
At the Artemis_Upgrades section of the wiki there isn't a T-Mobile file to download. The language doesn't matter to me.

Which device are you guys trying to flash with a new ROM, if its a UK T-Mobile device its not got the WiFi hardware so don't go putting a ROM on the device that expects WiFi support, T-Mobile Artemis units from Holland did have WiFi built in as does the true HTC P3300 unit, the UK T-Mobile device does not - Mike

RaZoR X said:
I did ran the USPL.
I took a look @ the wiki, but I think those files (all of them are less then 100k) are theme files.
"T-Mobile_NL_MDA_Compact_III_1.13.114.1_NLD_ExtROM"
IPL: 3.13.0001
SPL: 3.13.0000
The USB is working
With the "PDA Phone ROM Update Utility 3.6.3.1." from HTC I tried to get the MDA functional again.
In the Verify the ROM you want to update window it says this:
From:
Image version: -blank-
To
Image version 3.13.405.1
But after 2% sometimes 7%, it says this: "Error [244]:Invaild model ID".
So maybe the USPL didn't went well.
At the Artemis_Upgrades section of the wiki there isn't a T-Mobile file to download. The language doesn't matter to me.
Click to expand...
Click to collapse
ok hear'd this one many times before, your running vista >?
try and search the forum, there is a fix for this then your phone.

@Mike it's the "Dutch" version with indeed WiFi
@Neilhhardy
No, I'm not running Windows Vista at the moment.

Me too have the same problem - flash allways stop at 2% , also can`t flash radio - stop at 73-75% - any idea?
the phone is original HTC (have Wi-Fi and not branded) - never CID locked go to bootloader without any problems but can`t flasing - I think case problem is standart HTC flasher exe - for early models have different flasher software - I have Jaf WM but Jaf WM do not support Artemis - did have released other soft that alow flashing Artemis?
P.S - I thing cause right solution is to flash your device with original version - the OEM version that was instaled by factory will fix the problem

this worked for me on a unlocked mda compact 3
format your memory card first with your pc then copy the rom file (nbh)to your memorycard and rename it to ARTEIMG.nbh
start bootloader and follow the instructions.
http://wiki.xda-developers.com/index..._Card_Flashing
rom i used http://makus.folijka.pl/OrbitO2UK.rar

I found the right solution and fix my phone stop at 2% is hapenind when the phone was flashed before cid unlock (bricked) and can be restored ONLY with ORIGINAL version for that phone
1. go to www.htc.com then go to support area and register your headset by they own htc serial number!!! this is most important step!
2. download update soft - the supportsite know what exactly is rirgt version and language for your pda
3. Flash your phone and will be alive
4. USPL and make after that what you want with your headset
TESTED and WORKED for dead phones(but phone must go to the bootloader)

I did a reset with the rec, pwrbutton and resetbutton. And now he's up and running agian with WM6 Haha
I tried to unlock the device with the AthenaUnlocker, but I got this error:
0x0, 0x100000, SPL-verify.nb
I think I killed him lol

ppl said:
I found the right solution and fix my phone stop at 2% is hapenind when the phone was flashed before cid unlock (bricked) and can be restored ONLY with ORIGINAL version for that phone
1. go to www.htc.com then go to support area and register your headset by they own htc serial number!!! this is most important step!
2. download update soft - the supportsite know what exactly is rirgt version and language for your pda
3. Flash your phone and will be alive
4. USPL and make after that what you want with your headset
TESTED and WORKED for dead phones(but phone must go to the bootloader)
Click to expand...
Click to collapse
this may had worked for you but at the HTC website I get the error that my phone is not branded. true it's a tmobile phone...
can you give me the serial number you entered? if you dont trust it you may make the last 3 digits a X
thanks
Janus

HTC Herald,P4350 ERROR [300] INVALID UPDATE TOOL.

I received HTC Herald P4350 to change Language from NOrweign to English.
I try to use HERALD-USPL-beta3. and Now phone is dead
Only can enter in bootloader mode by pressing boot mode keys
and Only show
IPL :1.08.001
SPL :1.08.001
and I try to RUN Orignal RUU HTC_P4350_NOR_4.17.409.3_4.1.13.44_02.94.90_Ship.exe
and many other tools.
But I always get ERROR [300] INVALID UPDATE TOOL.
Any one here can share me the solution to unbrick this phone.
Br.

canonyang rulez)))
hate this numbers 1.08.001, as in "lost" film
DONT USE *SPL* (uspl,hardspl,jspl,another) IF YOUR SPL UNDER 4.00.0000

DrMobile said:
I received HTC Herald P4350 to change Language from NOrweign to English.
I try to use HERALD-USPL-beta3. and Now phone is dead
Only can enter in bootloader mode by pressing boot mode keys
and Only show
IPL :1.08.001
SPL :1.08.001
and I try to RUN Orignal RUU HTC_P4350_NOR_4.17.409.3_4.1.13.44_02.94.90_Ship.exe
and many other tools.
But I always get ERROR [300] INVALID UPDATE TOOL.
Any one here can share me the solution to unbrick this phone.
Br.
Click to expand...
Click to collapse
Send your phone to HTC Service Center, Same thing happend to me and they
changed it under warranty.

In my country there is no service center for HTC.
and phone is come from norway
I need solution. otherwise customer will eat me.
Br.
A. Wahab

Hi DrMobile,
Have you solved your issue? I have the same issue as you...
Please help by sharing with us the solution
Thanks,
Lamnl

same in my mobile error 300
i am still trying the rom without any success. please help

i have the same problem. my phone is showing bootloader , i have ipl/spl 1.08.0001 i tried anythin but nothing worked.
i hope there is a solution with our phones, and someone around here will take a look to our problem.

stuck in bootloader
i have the same problem.
eror 300
pls help

me 2 plz any one can help me 2 plzzzzzzzzzzzzzzzzzzzzzzzz

"those with a SPL lower than 4.0.0.0 or something like that gets bricked. I just wanted to get this first post edited to reflect that so that people don't keep bricking their phones."
(Moderator: whether this is accurate or not I do not know - but use your own discretion)2nd Jan 2008
from another topic, send them for repair

Try this:
http://forum.xda-developers.com/showthread.php?t=343450&page=2

Warranty got back my device back to life
Hi I bricked my device a few days back and tried all the stuff to bring it back to lifee but in vain... I finally gave up my trials and approached the service centre. They just replaced the motherboard inside and luckily everything seems fine now. They hadn't charged me anything as it was within warranty. Anyone in India if you need service centre address..
http://www.asia.htc.com/asia/in/support_sc.html
Though this site says HTC, I got my Dopod C800 serviced there...
Very few questions and cool guys.
Regards,
Murali

Now I think that the reason of non flashing, even with official RUU, could be corrupted CID-block after using HardSPL on devices with low IPL/SPL. I've read thread about similar problem with Wizard. The question is: how to restore the CID block in our bricked devices? I'm not even sure if this theory with CID-block is a reason...
What do you think about such a trick:
- Run RUU on someone's working HTC device but only until the moment, when it wants you to click the last button to finally proceed with flashing. (This step is to let RUU to know that this RUU is correctly dedicated to our device). It's a kind of fake for RUU, cause our CID doesn't match the CID of ROM included in RUU.
- Next disconnect working device from the USB and connect your bricked device with launched bootloader mode
- Next click the final button to launch flashing in RUU application. If the process of CID matching was done before this step, the flasher should start and let us flash our bricked device. But I'm sceptic to this solution. If it was so trivial, everyone could flash his device with different ROMs so easy...
I can't try this trick cause I don't have working HTC. What do you think? Will it work or not?
DrMobile said:
I received HTC Herald P4350 to change Language from NOrweign to English.
I try to use HERALD-USPL-beta3. and Now phone is dead
Only can enter in bootloader mode by pressing boot mode keys
and Only show
IPL :1.08.001
SPL :1.08.001
and I try to RUN Orignal RUU HTC_P4350_NOR_4.17.409.3_4.1.13.44_02.94.90_Ship.exe
and many other tools.
But I always get ERROR [300] INVALID UPDATE TOOL.
Any one here can share me the solution to unbrick this phone.
Br.
Click to expand...
Click to collapse

D'you mean
working Herald or any HTC?
I have the same prob

I'm thinking about working device, exactly the same as this bricked one - in this case Herald. But all of this is only a theory. I don't have enough knowledge about the RUU flashing process.
My another idea is to swap only ROMUpdateUtility.exe, rapitool.exe and EnterBootloader.exe files from official RUU dedicated to your bricked device, with different versions of these files from another HTC devices just to test if it helps to recognize our bricked devices by RUU. Maybe the problem is wrong version of these files? But which versions are correct?
I'm just trying to find a solution to unbrick our f.....g Heralds . I know this is only a matter of time and soon or later we will know what to do. Moreover I believe that there are people, even on this forum, who know how to unbrick our Heralds but some of them don't want to do us a favour. I know what I'm talking about...
GenePr said:
D'you mean
working Herald or any HTC?
I have the same prob
Click to expand...
Click to collapse

i have the same problem.
error 300
pleas help

have the same error...300
but i can manage via mtty using bootloader commands
when i put password <Bs...> the mtty shows last thing ive running and phone shows a progress bar with 0% (like.. what uve been doing last time?)
i think we can manage it via bootloader commands
i know.. i know
(at least our devices run bootloader mode, is recoverable!)
it can be flashed by SD? how?

Welcome to the club...
As far as I know, SD flashing doesn't work because of the CID-lock.
tramuyo said:
have the same error...300
but i can manage via mtty using bootloader commands
when i put password <Bs...> the mtty shows last thing ive running and phone shows a progress bar with 0% (like.. what uve been doing last time?)
i think we can manage it via bootloader commands
i know.. i know
(at least our devices run bootloader mode, is recoverable!)
it can be flashed by SD? how?
Click to expand...
Click to collapse

no, it cant be possible! im not goin to pay HTC Herald
there's a solution, a HOPE... (u try to flash with original flashfile?)

I thinks the solution is to unlock CID from bootloader mode, for old models i did so, but how to unlock Herald's CID

Desperate Help needed upgrading 8125!!!

First of all I am so sorry to bother you all!!!, as I can see from 3 days of non stop reading here and e;sewhere, its not always liked to ask questions, but I am sorry I really need help!
I bought a 8125 cingular from eBay (bought a x01ht but it hasnt arrived)
I have read seriously so much I am now confused! But I have tried to research this 100%
when I got the phone yesterday, I first sim unlocked it with the "All HTC" unlocker.. then I used unlock ext rom wizard, and Likiwiz02 for the cid.. I did see it say "your phone is superCID" unlocked or what ever...
I then tried to flash with x2h_wm 6.5 and it went through the steps like it should and finished and said your rom is updated, BUT when the phone rebooted, it was like it went DOWN not up.. I lost alot of things and now it said G not E for network, I had less signal, and had the roaming Icon. Well, after that My XP computer would no longer recognize the device.. I would plug it in and it would charge, and the active sync tries to connect but after a few minutes it says it can not connect.
I am able to "sometimes" connect top my Vista" device, BUT I have not yet mastered being able to flash a rom with Vista... as I always get RUU is closing, because of error.. and it leaves my phone in bootloader RUU mode, so i have to reset it. I have tried the instructions here http://forum.xda-developers.com/showthread.php?t=291723 and One time I was able to get pretty far without an errors from RUU, but it said I needed a newer version.. or something, and after that I am unable to do it do any RUU on vista, although most of the time I can get it to connect by going to the services- and restarting wm 2003 thing"
This is the details of my device (and yes I know is a G3)
IPL & SPL :2.25
gsn: 02.25.11
os: 2.25.11.1
Ext Rom: 2.25.11.102
Radio: 02.25.11
Rom 2.25.11.1 WWE (build 14928.2.2.0)
protocol ver: 4.1.13.12
My question is.. What am I doing wrong? How can I get either XP to connect, or Vista to run RUU?
Can I flash by sd card.. ( I have seen both yes and no, and am confused on how to do it)
Tweeks I have done is installed a cab to remove roaming icon, reg. changed the G to E for Edge... Speed it up bu changing mem. and I think that's pretty much it!
Scream at me and call me stupid, BUT Please help me.. There are 10000000000000 different HOW TO all over the place, and all are different, and I really just would like a little PERSONAL help from someone..
THANK YOU SO MUCH!!!!!!
Tony
Also.. On the Activesync issue.. I have uninstalled and delete all tracers on my xp laptop and reinstalled both the newest version , and when it did the same, I uninstalled and reinstalled an older version... Still the same!

http://wiki.xda-developers.com/index.php?pagename=HTC_Wizard
best thing is to start with reading the wiki

Read it over and over...
I am not just saying it when I say I have searched and searched!

UPDATE
Although I received no answers, I thought I would upddate... I am so embarrassed, as the active sync was an easy fix.. (disable Firewall) I cannot believe it is that simple, as it was working fine before with firewall..
Ok I am following the instructions now flashing with XP button rom, etc etc.. Will follow up later!

Ok progress!
Well, I was able to flash to phone to button rom, and then CID unlock it with lokiwiz, but My IPL and SPL are different. SO i flashed button rom again, and its still the same... Can I go ahead and flash back up, or what do I need to do?
IPL 1.01
SPL 2.25

tlbaker78 said:
Well, I was able to flash to phone to button rom, and then CID unlock it with lokiwiz, but My IPL and SPL are different. SO i flashed button rom again, and its still the same... Can I go ahead and flash back up, or what do I need to do?
IPL 1.01
SPL 2.25
Click to expand...
Click to collapse
If all was successful your good to go.
And yes you can flash back up.

I am so ANGRY... I got to 100 % and my cat hit the cable and Now its stuck in RUU... I am looking for a fix.. ANY HELP PLEASE?

OK... got it going again... flashing back down to button, the only one that would connect.. and I will build my way back up...
Sorry for posting so much.. and thanks for the help!

I have flashed to T mobile 2.26.10.2 , IPL/SDL are both 3.08 And I have tried several times to go beyond WM5.0 but It never loads.. Any advice...
Thanks

Connect the phone to the PC and run Wizard Service Tool and press Enab. RAPI + Unsigned Apps button.
Then press CID Actions Button and Read CID block, this will tell you if your CID unlocked.

Well, I will try that, BUT I am assuming since I have a Tmobile ROM on a ATT phone its no longer unlocked???
When I ran the unlocker it said it was now SuperCID unlocked or whatever..
I will do the Service tools and see.. and Post back soon! THANKS

It is locked!
OK.. I ran the tools and it said it was CID locked... this was the results (not sure if usefull or not)
Checksum : fb67d2a2
CID: WIZCNG01
Its funny because when I ran the other lokiwiz it said it was unlocked..
I tried to unlock it and it said downgrade SPL to 1.06 or less.. AND thats the problem... When I Loaded Button rom the 4 different times I have had to flash it.. THE SPL never changes down.. One time I flashed it, I repeated it 3 times as per some instructions i seen that if you flash it again it will change.. NOPE did not change, the IPL always changes, BUT SPL stays the same.. SO If I flash again, this is the results SPL 3.08 IPL 1.01
Can anyone help me .. maybe use a diffrent rom instead of button?
HELP PLEASE!
THANKS

Have you tried to go back to the original ROM?

Problem solved
I am still tinkering, and adding patches now... BUT I was able to get wm6.5 (VERY SLOW ON MY WIZARD) so I went back to button rom, and installed XDA Mobile 6 Release 5 ROM, and I LOVE IT!!! like I said I am still adding stuff and playing with it, but so far its better than WM6 I have on my Cheetah (treo750)...
I will add the steps I took , and trial and error steps, so other people that are impatient and ask questions like I did, will know what to do.,.. BUT let me play with my new toy for a while!!!
One question.. Should I stay with IPL/SPL 2.26? Or should I go back up to 3.08 or ?????
Thanks