Database Users

Reflash stock SPL

Hi, I know that here ais lot of threads about removing hrad-spl, but noone works for me.
I cant connect my Herald to computer (activesync doesnt want to be connected).
Can anyone help me how to flash original spl prom sdcard or from bootloader (i cant flash any rom from bootloader, i only cant use sctivesync)
I hope you can uderstand me, and i hope you will help me. Thx Stepan

i've never heard of anybody removing spl using SD card flash, but heres how it SHOULD go.
extract the SPL.nbh from an RUU using something like 7-zip
extract it to root of memory card and rename heraimg.nbh
go into bootloader, it should detect
follow instructions on screen (slide side slider)
wait (it takes unusally long for sdcard flashes)

I tried this, but it doesnt work :-( I need to get it repaired.
any other sugestion?
I tried sspl (jumpSpl) and It dosnt work, there is only white screen after running it :-(

I need help, please.
How to remove HARD-SPL withou activesync.
Thank you very much.

how do you mean it didn't work?
you tried the SD card method right?
it didn't work how?

So. I flasher SPL.nbh, and nothing happened. I think it is because of overwrite protection of that hard-spl (right?)...
Does anyone know how to make sspl (jumpSpl) working?
Or how remove hardspl overwrite protection, or how to overwrite hardspl.
thx

Does anyone know how to get back original SPL, without activesync?
I need my Herald

if you can't connect to your computer even in bootloader then something might be worng with your herald's mobo or something

I CAN connect to pc if i am in bootloader (i can flash rom from bootloader).
I cant olny connect to activesync :-(
Dou you have any solution in this case?

you don't need activesync to flash rom from bootloader. you just need that generic "pocket pc" connection. Try using the un-HSPL process while your device is in bootloader

HELLLPPP!!! stuck on bootloader on my first day i got the phone!

i really need help, i'm stuck on bootloader and i don't know how to re-flash because my computer won't recognize the usb?
my phone won't hard reset, someone please help!
my phone is an htc hermes, qtek 9600

Would be helpfull if you could tell us:
-Is there a hard SPL on the device.
-Which ROM are you using.
-what happend? Did a flash go wrong?
-Vista or XP?

As the-equinoxe says and the wiki and unbricking guide is easily found:
http://forum.xda-developers.com/showpost.php?p=1079011&postcount=1
Mike

Bo0mcxh402 said:
i really need help, i'm stuck on bootloader and i don't know how to re-flash because my computer won't recognize the usb?
my phone won't hard reset, someone please help!
my phone is an htc hermes, qtek 9600
Click to expand...
Click to collapse
Post #1160 http://forum.xda-developers.com/showthread.php?t=296722&page=116
Use the sd card method. My phone will not connect to active sync via USB, so i flash with the sd card. IMHO this method is safer and faster. Since you are stuck in bootloader, transfer files with a card reader from your pc, put the card back in the phone then soft reset. All should be good. Maybe once you re-flash you will get your active sync back.

the-equinoxe said:
Would be helpfull if you could tell us:
-Is there a hard SPL on the device.
-Which ROM are you using.
-what happend? Did a flash go wrong?
-Vista or XP?
Click to expand...
Click to collapse
theres no hard SPL
im using the old htc windows mobile 5 rom
yes, the usb cord got disconnected by accident
im using windows vista

[HELP] Bricked TyTN

Hi,
I'm kind of new around here.
My problem is as follows:
- TyTN running PaysRom for about 9 months
- Started to get very sluggish
- Unable to get signal
When i booted my HTC the 'R' and 'G' that appear on screen and used to have values in front of it now display 'none'.
So, I connected it to my PC, 'activesynced' it and tryed to install a new ROM, hoping it would solve the problem.
But the new ROM wasn't installed sucessfully and now all I got is a brick.
I can't even connect it to ActiveSync since it's not recognized.
Is there any solution to my problem?
TIA,
hype

Can you get to the Bootloader?

Yes..
By pressing the Ok+Power+Reset on the bottom button, I see the 'RGB'+white thingie, that I believe is the bootloader..

What SPL do you have? Is it Hard SPL V7(2.10)?
If it is, use the sd card method to install a new ROM.
remember to backup your card 1st.
1. Format 2Gb or less sd card FAT32. Copy .nbh file of the ROM you want onto it and rename to hermimg.nbh .
2. Insert card into Hermes and reset into bootloader.
3. If all things have been done right, follow the prompts....
If the radio ROM has died, I'd suggest trying to flash the Shipped Stock ROM 1st and see if that actually fixes the problem with the blank values on R & G. WM06 upgrade of shipped carrier ROM should also work.
Cheers...

Tks for your response.
I tryed the SD Card method already, with no sucess.
The red stripe shows as follows:
Code:
HERM200
IPL-1.04
HERM200
SPL-2.03
Everytime I tryed on another ROM I always perfomed it using SafeSPL.
Since I don't have 2.1, what can I do?
Tks for all ur help.

What happens when you try and flash a ROM over?
Do you get any kind of error?

You need to find the SHIPPED STOCK ROM. WM06 upgrade should be OK as the CID should match.
Put Hermes into bootloader and connect to PC after unticking "Allow USB Connections" in Activesyncs settings on the PC.
Run the RUU_Wrapper.exe file of the SHIPPED STOCK ROM. ven though activesync won't etect it, the flash file should. Follow the prompts.
Good luck as this seems to be the only way to fix this.
Good Luck...

You might be able to flash a Stock WM5 ROM using the SD Card method. Worked for me when I had SPL 2.03. In fact that's the only ROM it would let me flash over when mine bricked.

USPL via memory card method?

Guys, I have a P3300 that has a non-functioning USB connector. Charging works fine, but it will not sync over USB at all. The device is not detected at all. Even in the bootloader screen, when the USB cable is plugged in, it DOES NOT say "USB" in the bottom corner. Basically, the data functionality of the USB port is fried.
I had used USPL to flash a cooked ROM onto the device, and when the USB port worked, it all went fine. Now, with the USB port not working, I can only flash a stock ROM onto the phone using the memory card method. If I try to flash anything other than the stock ROM, it says "certificate invalid" and won't do it.
I read somewhere that there might be a method of doing the CID unlock by using the memory card, since the phone will not communicate with the computer via USB to use USPL the normal way. Can someone instruct me on how to do that? I have the USPL files on my computer, and simply renaming the .nbh file in order to try to use the memory card method won't work.
Can someone help me figure out how to use USPL or otherwise CID unlock the phone over some method other than USB to the computer? Thanks,

Well you can use activesync over BT, right? That might just do teh trick + SD card flash after it reboots to bootloader.
I might be wrong, it's just a thought

I tried that, but the USPL loader kills Activesync right at the start. So once the phone soft-reboots into the white screen and AS is killed, there is no more BT connection. So the USPL loader fails with an error of not being able to connect.

Can anyone else help?

I faced the same problem. White screen. I removed SIM and SDCARD. So I can flash normally.

Wiki: Artemis SD Card Flashing
Try reading the Wiki on Artemis SD Card Flashing
Those having questions on flashing (i.e. updating) their HTC Artemis could try following these steps 1) Backup e.g. PIM Backup 2) disable standby and hibernation then remove SIM & SDHC cards 3) if necessary then cid unlock 4) recommend hard reset or update to the latest official build 5) if necessary Update SPL to latest 1.11.cmon 6) flash new rom then hard reset 7) put in SIM & SDHC cards and enjoy the result of the hard work by the developer
Also check out this thread Uspl/rom upgrade/tips&tricks
Cheers
Tom

hello. I exactly have the same problem like the thread poster. my mini usb only charges and cant connect data to any pc. its probably broken as common with using the O2 artemis on a car phone charger and starting the car while the phone is still sitted and charging.
MY QUESTION: does "Artemis SD Card Flashing" doesnt require the USPL? since its CID locked?

please help. can no longer flash from card (RESOLVED)

Hi
Have been flashing roms all the time without issue.
I've tried to flash my mobile and get to HSPL boot screen but it doesn't recognise the leoimg.nbh no matter which rom i use
It says 'loading...' on a grey screen then goes to the red/green/blue screen and has 'serial' at the bottom.
i've tried upgrading hspl to 1.66 and also mtty format, oth worked fine, I now just can't flash any rom to the phone
Can anyone advise how I could sort this? could send paypal for your time if you can help me sort it
Cheers

ok
format again microsd to fat32,microsd not microsdhc,
charge your battery,must bt shure your rom its ok not corupted

Hi
Have tried all of this but still no joy at all.
Does anyone else have a suggestion or is there another process that can be used for flashing if a direct flash from memory card doesn't work but the phone is formatted?
Thanks in Advance
Adam

In case anyone has a similar problem:
I installed drivers for phone in bootloader USB mode from the mtty thread.
Set the phone to bootloader and plugged in usb and was able to flash from PC without having to be in winmo
I still can't flash from card but as this way works, it's not an issue.
Cheers