Related
I lost the loudspeaker-sound in my Himalya. It works using headphones. I think it may have to do with another set of headphone I connected to it, which was not original. Perhaps it put the device on permanent headphone mode. But then again it might not have anything to do with that.
Is there a Himalaya expert in Berlin - Germany who might be able to help me with it? I dread having to send it to the official reapir center, as I expect it to cost a neck and a hand.
Happened to me when I received a call whilst listening to music. I pulled the headphones out before answering the call, and then answered it. I could here them but they cvouldn't hear me. If you plug the headphones in again and remove them it solves the problem. Well it did for me anyway
I tried that. I doesn't do it. It doesn't matter what kind of sound, if Media Player file is played of phone ringing, only the headphones work. I think I need a dotor.
I have read a lot about the problem in others threads. It seems the headphone-jack can get stuck, not making a contact, which normally is being made and which turns the XDA back to speaker mode, when the headphone-jack is pulled out. Hereto:
1- What does that mean exactely? Which part is that, in what part in the on-board jack? If it had been bent out of place, is it possible to bend the part pack (at best without having to disassemble)? (I tried the ramming in and out, no go).
2- I looked at the non-original jack I had used and it is about 2 mm longer than the original. Might perhaps that explain it? Is there a part in the back that could have been bent out of place?
3- If indeed this was the problem (if the jack had been bent out of place, one way or another), would the microphone work? I can record using the dictaphone and the micophone also works during a call.
When we had himalaya's it happened to both of our devices (my wife and I had one each).
It appears the spring in the speaker can come loose. I used to bang mine (pardon the pun) on my palm and sometimes it would start to work. Then we broke the speaker protection shield, and this made it easier sometimes and hard to fix in others.
When I sold it, my friend took it apart as it was out of warranty, and as he is electrically minded, he find the dodgy bit, and soldered it to the device, and now works perfectly.
Yes! Thanks Jasjar. It worked after a bit of beating.
I found a detailed instruction of how to fix it permanently in another thread. Sounds complicated and dangerous but eventually I must do it.
ran2far said:
I have read a lot about the problem in others threads. It seems the headphone-jack can get stuck, not making a contact, which normally is being made and which turns the XDA back to speaker mode, when the headphone-jack is pulled out.
Click to expand...
Click to collapse
Sorry for kicking the topic, but this was the solution for me. I just poked in the headphone-jack with a little stick and tataaaa... my sound is back!
Sound lost problem
Hi all,
same happen to me, the sound stoped working (on my side it had nothing to do with the phone jack).
After the modifaication which is described in this forum i had still the same problem so i solder the loud speaker directly - still same problem...
After some time i flashed the device again, now it works, so on my side it was a software problem...
The device was 3 month out of power, but i think remove the battery and if the sound appears on startup (on first boot) but later not, then flash the os and it will work ...
kr
chw
XDA 2 sound problem...
Hi!
Plese help me!
I have strange problem with my XDA 2.
I bough it 2 days ago. It was in O2 network.
Now when I unlocked it for my network (polish ERA-GSM) I saw that when I'm calling I cant hear anything. Person from the other sight can't hear me too..
XDA have sound becose I used media-player ando other sound stuff, thats why I think that speaker is ok. Microphone is ok too becose I can record animations with sound.
So what should I do now? ;/
Plese help...
Just for reference:
A friend of mine had this 2020, and both Speakerphone and mic were not working.
When somebody called, the ringtone DID sound.
Anyway, bluetooth handsfree worked fine.
All we did was play with the jack, using the stylus! Not even headphones...
And now it works fine!
He says he'll never put phones on it again... lol
cu around!
Looking for more Info
Hi, please help me find which points in the MDAII Motherboard can I solder to disable the headphones and get the audio and mic back to the MDA.
After a while my headphone-jack is broken from the motherboard and now I only have the pin outs in it.
The device is working perfect, and I can use bluetooth headphones. I just don't have audio in the speaker and no mic without bluetooth.
I hope someone can tell me which of the red points en the picture can I solder to disable the headphones.
I just want to do this temporally until I get a replacement spare part for it.
Thanks
EDIT: 12-12-2007
I got it. Just joining 1 and 3 and you will get audio back to the PDA disabling the headphones jack.
Thanks anyways for reading this..
Did you find out what all the mboard pins are for the jack?
I have a dodgy jack and would like to take flying leads of the mboard jack to an external (easily changed) inline jack. Does any know what the 1 to 6 pins correlate to. I would like to still switch the audio via the external jack. Not bothered about the mic.
TIA.
The rear speaker of my JAMin blew... I need a replacement so I can do the work myself and not have to send it over for a week to the lab. Where can I get one?
Thanks,
Nir
How to repair the sound issue on Prophet
Hi
I could read a lot of posts on that issue and found this solution:
Remove the battery cover. Then the camera cover: to do so, lift up the gently the cover starting from the side of the battery.
You will see something looking like a fan. This is the speaker. the problem is with the red wire whixh connect the speaker.
Turn on your prophet and run your favourite MP3 song.
then touch the red wire with your stylus. The sound should come back. Insert a piece of folded paper to keep the cable properly fixed. that's all
Watch out not to wish to fix it too nicely, you could damage the wire !
Hope this help, otherwise a return to the service department will be necessary !
Hope this helps
Regards
Régis
Hay the paper trick works!
I went here to learn how to remove the flap to the speakers:
http://www.modaco.com/index.php?showtopic=240109
Well, my speaker had the voice coil broken... touching the membrane would bring it back to life but that is no real solution. I replaced it with a speaker from a used old cellphone with some minor use of hot glue to fix it in place and seal around it.
It works now just as new.
Nir
yeah it is a real Problem.
mine is broken twice in 6 months.
tried the paper thing. but it sometimes sounds weird and there's some hissing. maybe I did it wrong. so I tweak it a bit and just lost it completely. no sound whatsoever now.
went to the service center today. they said that they have a new batch of speaker which supposed to be better than the previous one. if anyone can confirm.
rlou77 said:
Hi
I could read a lot of posts on that issue and found this solution:
Remove the battery cover. Then the camera cover: to do so, lift up the gently the cover starting from the side of the battery.
You will see something looking like a fan. This is the speaker. the problem is with the red wire whixh connect the speaker.
Turn on your prophet and run your favourite MP3 song.
then touch the red wire with your stylus. The sound should come back. Insert a piece of folded paper to keep the cable properly fixed. that's all
Watch out not to wish to fix it too nicely, you could damage the wire !
Hope this help, otherwise a return to the service department will be necessary !
Hope this helps
Regards
Régis
Click to expand...
Click to collapse
That's great, this fixed my problem. After I touch the red wire with my stylus, the speaker just works fine, don't even need a folder paper.
starrayfly said:
That's great, this fixed my problem. After I touch the red wire with my stylus, the speaker just works fine, don't even need a folder paper.
Click to expand...
Click to collapse
I'll try this one myself - my speaker just died again - it's been back once already.
Well, I followed the instructions above and now I have a working speaker again. A very low tech fix to a high tech device.
I have found a small bit of sponge does the job better than folded paper.
what is the type of speaker.
i mean can i use any speaker?
what's the best?
Mohammad, you seem to have missed the point of the replies in this thread. We don't know where to get another speaker from but we do know how to make the existing one work again.
oh, dude!!!
sorry
What a piece of ugly Speaker: O2 xda Neo!
Hay Guys,
I am suffering from this nasty problem since sometime. My brother has tweaked the speakers with a metal piece seem to work. However if I use speakerphone, it goes off.
Is there a permanent solution to this constant spurce of unhappiness.
Incidently I have been blessed with a on & off camera problem as well. I think I will never buy a DOPOD product in my life again.
My Camera has those colour matrix instead of proper images. Occasionally it behaves normally. I have tried hard reset already.
Any body? help !!!!!
Ugly Speakers: O2 xda Neo
Hay Guys,
I am suffering from this nasty problem since sometime. My brother has tweaked the speakers with a metal piece seem to work. However if I use speakerphone, it goes off.
Is there a permanent solution to this constant spurce of unhappiness.
Incidently I have been blessed with a on & off camera problem as well. I think I will never buy a DOPOD product in my life again.
My Camera has those colour matrix instead of proper images. Occasionally it behaves normally. I have tried hard reset already.
Any body? help !!!!!
I tried this....when i touched the red wire i got the sound back i was happy.. but not for long cause touching the wire now doesn't help anymore so i have to send it back
drdeepak said:
Hay Guys,
I am suffering from this nasty problem since sometime. My brother has tweaked the speakers with a metal piece seem to work. However if I use speakerphone, it goes off.
Is there a permanent solution to this constant spurce of unhappiness.
Incidently I have been blessed with a on & off camera problem as well. I think I will never buy a DOPOD product in my life again.
My Camera has those colour matrix instead of proper images. Occasionally it behaves normally. I have tried hard reset already.
Any body? help !!!!!
Click to expand...
Click to collapse
I wedged in a piece of foam. That's worked a treat.
The manufaturing quality of HTC is bad
I also have the speaker problem. And thanks for all of you to suggest that sponge and folder trick. I did it and i have put a small slice of ear plug sponge. For past 2 days my spearker is working. But dont know how long will this sponge give my speaker lifesupport. I am sure after few days again its going to be problem. Hey,...... is there anyone in this thread who has used sponge/paper and the speaker is working for long time.. at least a year ?.
These HTC products seem really bad quality products.
that worked
http://www.4shared.com/file/6894706/ca35cee6/altavoz_s200.html
motorola l7 speaker is too a candidate
It's too bad they saved on the speaker. Guess the manufacturer of the speaker had a very nice presentation @ HTC
Trying to download that pdf file, but it's not working :/ However I've read on other occasions that people talk about that motorola speaker as a replacement. Might be worth giving a more detailed look into that.
What exactly is the problem with the speaker btw? Did anyone narrowed that down already? Why is the speaker not functioning properly?
pdf
The file contains instructions to change the original speaker using the spk of a motorola v525.
I did it yesterday, and works fine, but isn´t easy to do it
Hi all
It would be great if you shed some light on the problem
Xda exec had a fall!..since then no sounds at all, phone won't ring or won't play music...but has sound if i plugged the headphones in
Any theories/ideas what might have gone wrong...& possible solutions..
any help would be appreciated...thanxs
sound failed on xda exec
i also had the same issue but my handset was replaced as it was within 28 days of getting the handset
i never did manage to find the exact issue
when your handset fell did it have external sound / handsfree plugged in at the time
about the only thing that made any sense with mine was the possibilty of the micro switch / contacts of the externl audio jack being damaged
dont know if any of this info helps you at all but best of luck getting it sorted
Still no explanation for the no sound problem Xda Exec
Does anybody find out allready what's the problem with no sound on the Xda Exec.
I not speak about the problem with the external audio jack.
I can make cals like normal, I only can not play music or listen if somenone is calling me.
Thanks
its hardware problem with universals audiojack .. just open device ..remove board . plug headphones ... and see on connector /.... in most cases no sound issue cames from third pin of jack (thst pin detect plugged headpnones .. if it disconnected device plays in headphones if connected device plays on builtin speakers) if near end of it ...
a may advice you more deeply but i didnot have proper photo to explan in his basis..
just give me HI RES PHOTO OF BOTH SIDES OF YOUR MOTHERBOARD.. i explain what to do
mo3ulla said:
its hardware problem with universals audiojack .. just open device ..remove board . plug headphones ... and see on connector /.... in most cases no sound issue cames from third pin of jack (thst pin detect plugged headpnones .. if it disconnected device plays in headphones if connected device plays on builtin speakers) if near end of it ...
a may advice you more deeply but i didnot have proper photo to explan in his basis..
just give me HI RES PHOTO OF BOTH SIDES OF YOUR MOTHERBOARD.. i explain what to do
Click to expand...
Click to collapse
Thanks for your post.
You are shure that this willbe the problem, because I can make calls without the headphone. I was thinking that in the case that the connector gives the problem, I should also not be able to make any calls without using the headphone.
Anyway I was going to open my friend one day, to look what's up.
problem may be repaired in home in 10mins
you need
hands
brain
tools to open
1 needle
do photo .. i say what next
mo3ulla said:
problem may be repaired in home in 10mins
you need
hands
brain
tools to open
1 needle
do photo .. i say what next
Click to expand...
Click to collapse
Ok, here we go.
We have hands, tools ( a hammer ) and 1 needle.
I think I forgot something, but...
I think the problem, when the problem is hardware,
is that when you put the headphone jack, the top of the jack he opens the microswitch what you see at first.
Ofcourse when this switch he stays also open when you take out the jack, than you have a problem.
And yes with a needle you can first open the contakt and than you can dress littlebit the position of the contakt.
I have only 1 problem on my tel, this switch is closed as well, when I take out the jack. The problem is not this switch.
here we go
Correct, I am shure that this is almost always the problem.
In fact the switch is closed in normal position, and he goes open when you put the headphones.
When he not close as well automatic than, you have a problem.
But in my case it is really not this switch, so I am still looking for the reason why I not have sound.
hi all
i have same probelem like you
my friend using my device for weeks and when she give it back to me i have no sound from my device & even from headset i call the i-mate center the girl told me maybe your jack is dameged but when i sent it to suport center they told me your flex cable is dameged by wrong rotating your device and we haven't that yet ....
they sent it back to me and after some day my screen shows nothing then i buoght a cable from ebay an change , now i have voice sound screen
&....
like before
i hope these usefull for you
This was exactly my issue, under that pinkbox you marked is the tiny tab that makes or breaks contact with the internal speaker. Because my headphones break the contact, this tab after much use was stuck in the open position even after the headphones were removed. When I did the procedure you mentioned magically, sound..wow. I am extremely greatful for your troubleshooting skill.
Thanks a million mo3ulla.
If only i had this fix 2 phones ago..hahhahah.
lambrechts said:
Correct, I am shure that this is almost always the problem.
In fact the switch is closed in normal position, and he goes open when you put the headphones.
When he not close as well automatic than, you have a problem.
But in my case it is really not this switch, so I am still looking for the reason why I not have sound.
Click to expand...
Click to collapse
Hi lambrechts,
Did you manage to find out the reason?
i have the same problem, my device fell, but i didn't notice the problem until next day (i didn't use it) so i'm not sure if it is because of the drop.
I will open my device and check the Jack pins, but i want to know if you got any fix for this.
mo3ulla said:
here we go
Click to expand...
Click to collapse
hey mo3ulla, did your method work after repeated use of the headphone port? did it get stuck again any time after you fixed it?
just asking cause i have this problem on my 9000 and haven't opened it yet so i don't want to open and close it repeatedly
thankss
I have this problem aswell. But I inserted a fork and twisted it around a little and now it works as it should again.
Bumping this thread. Should be a sticky or in the wiki.
Anyways,
I tried the pin trick back when I posted here, it worked but it wasn't permanent. Instead I put a crumpled piece of post-it note above the pink dot in the picture and it worked, up until recently. Does anybody have a method to bend the connecter back down? I'm probably not using the needle right, I press the pink spot, but it pops back up.
Ideas?
twisting the pin really helps. thanks for the solution. I tried to insert my headphone again and the pin always stucked. I'm trying to find a permanent solution for this. Maybe put something to push the pin to be connected everytime I remove the headphone...
I hope this helps. I found it very useful to my Dopod 900. I tried to connect my headphones (sounds works on my headphone) then I disconnect it and sounds works on my stereo/speakers.
*Please do it carefully in pushing the pin upward from inside the hole. Just push it a little bit just enough to touch the upper pin..
additional tip: after you fixed your device, try to install SRS Wow for great audio experience
Quick Fix
I found that if you apply a little pressure between the base and just above the send key this seems to work, I tried this tonight and will report back if goes again.
luckyearl said:
Hi all
It would be great if you shed some light on the problem
Xda exec had a fall!..since then no sounds at all, phone won't ring or won't play music...but has sound if i plugged the headphones in
Any theories/ideas what might have gone wrong...& possible solutions..
any help would be appreciated...thanxs
Click to expand...
Click to collapse
could be a damaged PCB motherboard, or lose connetion for the sound chip!
you could try fixnig it, or replacing the motherboard.
a new motherboard could be bought off E-Bay US for a cheapish price =]
genspeed said:
I hope this helps. I found it very useful to my Dopod 900. I tried to connect my headphones (sounds works on my headphone) then I disconnect it and sounds works on my stereo/speakers.
*Please do it carefully in pushing the pin upward from inside the hole. Just push it a little bit just enough to touch the upper pin..
additional tip: after you fixed your device, try to install SRS Wow for great audio experience
Click to expand...
Click to collapse
Not sure if the srs wow will work, last time i tried it give lots of other problems like; mute the sounds, works great after you press the power button on and off, then no GPRS and Internet conectivity but if you have worked around those probs pls give an idea?
Hello guys! My loudspeaker suddenly stopped working few weeks ago. I know the cause, and I am pretty sure it is hardware related.
Here is the story:
I installed this ROM (don't think it's important). It worked fine for about a month. The sound volume was lower than MoKee or MIUI, so I started searching for some solution.
I followed a guide similar to this to boost volume, and it worked!
Although I read in the post to not set the value over 95 (to avoid damaging speakers), I decided anyway to set it to 100, because I didn't think that could happen. Sound was very loud, and I was very happy.
Next morning, alarm screamed very strong, but suddenly stopped ringing. I realized my mistake, loudspeaker is completely mute since then.
Earpiece, headphones, microphones work, everything works except loudspeaker.
I hoped so much that was software. I formatted and installed some other ROMs (MoKee, MIUI, CM12) but still no sound. Then I restored a previous MoKee backup (taken when sound worked) but no success. Unfortunately it's a hardware thing.
I bought a new loudspeaker, learnt from YouTube how to open the Note, and replaced it. Still no sound.
Then I tested both loudspeakers (the original and the one I bought) and they both emit sound when attached to an external source (jack plugged to mp3 player). So the problem is not in the loudspeaker itself!
My knowledge ends here.
How can sound stop working by simply raising a software value? But above all, how can the loudspeaker work correctly, but not when placed into the phone? Is there another component that can be damaged in abovementioned way? If so, can that component be replaced?
I hope somebody could share some knowledge to help me solve the problem, or at least point to the right direction. Thanks in advance.
Open your Phone and look if something "looks" broken and make a picture for analysing. It can be not anything but more that just one piece that's broken.
(Sry for bad English, I'm from Germany)
OverBit said:
Open your Phone and look if something "looks" broken and make a picture for analysing. It can be not anything but more that just one piece that's broken.
Click to expand...
Click to collapse
I opened it many times today, but discovered nothing wrong or weird, although I'm not an expert so maybe I simply haven't noticed.
Will post picture as soon as I manage to take photo without phone
Yeah, its like taking a selfie with your phone on your phone without mirrors, only Chuck Norris can do that
(sry for bad English, I'm from Germany)
Some photos
I resurrected my old phone and took some photos. As I said, there's apparently nothing weird, nothing that appears burned or cut.
Here three photos (full phone, upper part, lower part) the loudspeaker contacts are highlighted.
I don't expect a hint on how to fix that (although I hope so much ) because I know this forum is meant for developers/modders/those working with software. My real question is:
Why after just altering value in mixer_paths.xml my phone is now mute? Can someone describe how the sound goes from the CPU to the loudspeaker? Is there something I can do?
udda90 said:
I resurrected my old phone and took some photos. As I said, there's apparently nothing weird, nothing that appears burned or cut.
Here three photos (full phone, upper part, lower part) the loudspeaker contacts are highlighted.
I don't expect a hint on how to fix that (although I hope so much ) because I know this forum is meant for developers/modders/those working with software. My real question is:
Why after just altering value in mixer_paths.xml my phone is now mute? Can someone describe how the sound goes from the CPU to the loudspeaker? Is there something I can do?
Click to expand...
Click to collapse
I did the exact same thing. I replaced the loudspeaker just like you. My sound still doesn't work. I have done a complete factory reset and tried new roms and nothing works.
tripper22 said:
I did the exact same thing. I replaced the loudspeaker just like you. My sound still doesn't work. I have done a complete factory reset and tried new roms and nothing works.
Click to expand...
Click to collapse
My friend device redmi note 3g got same problem.. tired change with new rom.. new speaker..and factory reset that all not work..so open the case..and discovered .the problem came from cpu/chip . coz mtk chipset camera n sound came from cpu..
Hi Guys
I have exactly the same problem with my Xiaomi Mi3. After display replacement lound speaker stopped working. While I had broken display (just the touch screen, dispay was fine) loudspeaker worked fine (I cannot switch off alarm, even shut down the phone)
I bought new speaker, but sound still doesn't work. Do you think that it is comming from CPU? It is possible but I don't think so, because everything works fine via earphones or bluetooth speaker.
Did you find any solution?
tripper22 said:
I did the exact same thing. I replaced the loudspeaker just like you. My sound still doesn't work. I have done a complete factory reset and tried new roms and nothing works.
Click to expand...
Click to collapse
nokovica said:
Hi Guys
I have exactly the same problem with my Xiaomi Mi3. After display replacement lound speaker stopped working. While I had broken display (just the touch screen, dispay was fine) loudspeaker worked fine (I cannot switch off alarm, even shut down the phone)
I bought new speaker, but sound still doesn't work. Do you think that it is comming from CPU? It is possible but I don't think so, because everything works fine via earphones or bluetooth speaker.
Did you find any solution?
Click to expand...
Click to collapse
I tried many other ways, none of them worked. I ended up buying a small BT speaker and carrying always with me.
In my case I learned in the worst way that excessive software amplification can burn audio chip. I replaced EVERY replaceable part (speaker, USB/speaker lower board, main ribbon cable, maybe others I don't remember) with no success.
@tripper22 I think you have no options. If you did my same steps, sadly your sound is lost. I have not yet replaced my phone only because there was a recent increase in development, and many custom ROMs to flash, but I will probably change that phone sooner or later.
@nokovica My sound from earphones or bluetooth is working too. I remembre reading that the audio amplifier is in a separate chip.
Anyway, your problem looks like a HARDWARE issue, since you didn't played with system configuiration. This is easier to fix (if it's fixable, of course).
If you did the replacement, you could check twice if some ribbon cable went damaged. You could try turning on your phone while open (remove back panel and expose board and cables) and see if works this way. You could check with a multimeter wether some signal (albeit small) come to the buzzer. In my case I discovered that a little signal (2-5 mV peak) reached the buzzer, but wasn't enough to make a sound. Rechecking after some months revealed that even that little signal is now gone (maybe sound chip damaged further).
If someone else did the replacement (hopefully Xiaomi assistance) it's their fault, and you can usually ask for repair for free.
Mi3 Loud Speaker Problem
@nokovica
Even I am facing the same problem with my Mi3 . After screen replacement ( touch + digitizer ) My loud speaker is not working , however phone speakar and mic is working perfectly fine , even the headphones too. I also detected one of the problem with Network Signals , if last for only few seconds and then it goes off , i tried placing many sims, but no luck . Can any one in the forum provide some solution to the Network Signals ?
even I have the same problem with my redmi note 3. I just opened back case, sub-board loudspeaker and re-assembled it. I didn't touch motherboard or any flex on upper side. Loudspeaker stopped working since then. Swapped with new part but it still doesn't work. Headphones and ear piece works fine. doesn't play music on bluetooth but hands-free works on bluetooth. how could have damaged audio chip on motherboard?? I barely touch it. didn't even unscrew it.
ilyasabdul said:
even I have the same problem with my redmi note 3. I just opened back case, sub-board loudspeaker and re-assembled it. I didn't touch motherboard or any flex on upper side. Loudspeaker stopped working since then. Swapped with new part but it still doesn't work. Headphones and ear piece works fine. doesn't play music on bluetooth but hands-free works on bluetooth. how could have damaged audio chip on motherboard?? I barely touch it. didn't even unscrew it.
Click to expand...
Click to collapse
Did you solve? I have exactly the same problem
I have faced with no audio (at all) with mi5s
couldnt call or answer (hanging phone)
speakers dont work
erarphone dont work
i flash several times the phone and reste factory it and no change.
i read somewhere thet it resolved with warming sound IC in mainboard.
have any body solution or explane to problem?
Alright i am going to make a new thread, i created an album on imgur and posted on reddit and in another thread here, but still have people asking how to fix it. Hopefully this turns up in google/xda forum search.
https://imgur.com/gallery/5cou6
LG G6 suffering from intermittent disconnections, Google Assistant popups or track skipping? Simple fix for that, no need to send the phone in or have it replaced.
Side note: I am what some would call an audiophile/audio enthusiast, and I also work in the live sound industry, where setting up sound systems and operating them also requires me to play songs off my phone to keep you entertained at times. My ATH-M50x started to suffer from the above problems with all 3 cables and i was wondering what happened, apparently LG has bad manufacturing tolerances and this is the result. When the tabs get depressed, the intermittent connections cause the phone to go crazy, and cables with 4-pole/TRRS (meaning with a mic) tend to be
very slightly larger than the standard 3-pole/TRS jack. Hence other people mentioning that 4-pole cables working while standard 3-pole doesn't.
You saved me from sending my phone back.
Thanks 1000 times!!
I replied in the other topic already, but seems that one is dead.
Thanks a bunch for this wonderful tip, no more crackling sound when connecting, no more sudden voice assistant popping up. :highfive::good:
Oh my goodness, thank you so much, first my camera, then the audio jack, glad I could save the audio jack! It's a nice phone, but I feel like quality wise it's half way there compared to other phones. Thank you again!
Perfect!
Thanks man, it perfectly worked! You made my day!:good:
OMG ! thanks, i love you! I started with this problem after immersing it in the water. Then I noticed that the plug had been sulphated and I cleaned it with alcohol.
Thanks, thanks, thanks. I just before three days bought ATH-MSR7 and I was thinking that I have bad original audio cable. So problem is gone.
This worked for me and fixed my headphone jack, just encouraged the right hand tab out slightly and the intermittent connection is must more reliable.
Thank you sir
:victory:
thanks!!
You're a lifesaver.
A huge thanks again, my problem wasn't that serious but with the auxiliary cable just moving around a bit creating a buzzing noise while driving due to a loose contact was just annoying me knowing this phone isn't that old
Thanks man , from ??:laugh: