Activesync + bluetooth = after some minute bt switch off - 8525, TyTN, MDA Vario II, JasJam General

Hi,
I have this issue with activesync: If I connect my tytn to activesync via bluetooth, after some minute that my pda is in standby mode, the pda's bt module switches off (*attention*, no activesync disconnection BUT bt module switch off!)
someone has a solution?
Thanks in advice
regards
Ale

Related

three bluetooth connections Simultaneously

Hi guy's ,
I have make all this connected at the same time!:
1) ActiveSync via Bluetooth running and syncronising,
2) EMTAC bluetooth GPS connected and sending datas
3)HBH20 connected and a phone call established !!!!!!!!!!!!!!
Some one did the same :? :? :shock:
Yes I'm using Towa Bluetooth patch
I already succeded two connection GPS and Headset but why sync at the same time ?
EUUUUUUUUUUH ! just to see if it's possible !
Because who knows? they talk about a bluetooth keyboard for soon ........... :roll: :idea:

Qtek S100 -> Crasy Bluetooth?

Hi,
With my S100, (ROMs 1.12...)the Bluetooth works only if the USB cable is connected and synchronized with computer!!!! If I don't connect it, the bluetooth radio works a few secondes then turn off! (Of course I have tried everything: softreset, hardreset, SHOUTreset...) but the radio bluetooth ever turn off after a few seconds...
And if I use Bluesoleil (+switch bluetooth, see ''stack post''...) it only works when connected with USB cable!!! If not, Bluesoleil doesn't work too!!!
My question is:
IS IT NORMAAAAAAL??? (bluetooth works only with usb cable)
If yes, the bluetooth on a PDA is completely stupid, isn't it??
(IF I WANT A BLUETOOTH PDA, IT'S TO USE IT WITHOUT A CABLE!!)
Please Heeeeeeeeeeeelp!
How old is your device? Have you considered that most probably your battery is already defective?
...
Thanks for your answer!
How old is your device? Have you considered that most probably your battery is already defective?
Click to expand...
Click to collapse
Well, no I bought it in december 2005...
I didn't notice any problem of battery when I use the qtek...
(How could I see if my battery is defective?)
I noticed that sometimes Bluetooth works a few seconds before the GPRS connexion starts... the BT blinks, turns on & off... then stays on... then blinks again... then turns off !
Does the radio bluetooth use the same "channel" as the GPRS to work???
Thus, I have the impression that I must choose between telephoning and using the bluetooth… and moreover that the qtek must be connected with an usb cable to work! This is exasperating! :-(
Bluetooth need usb
PS : If I connect and synchronize my s100 with the usb cable, bluetooth (and bluesoleil too) works. A soon as I disconnect the cable, I loss the bluetooth radio after a few seconds... And the S100 (when I use Bluesoleil) say to me:
"Your Bluetooth device initialization fails! Do you want to configure it manually?"
Click to expand...
Click to collapse
So, it means that bluetooth need usb cable ant that is foolish!
I have BT on all the time and have no problems using TT and phoning at the same time. BT consumes a lot of power thus to check if the battery is the problem, fully charge your battery then start using BT. When the problem occurs check for the battery status.
ok
Ok, thank you for this information (GPRS + BT together).
Regarding the battery, I have bought a new one on the web, I'm waiting for it...
...
Hi,
my Qtek S100 has always a problem: the bluetooth radio works fine when the S100 is connected with Usb Cable. But as soon as I disconnect the usb cable, the bluetooth icon blinks then become deactivated.
What could be the problem?
Thanks.
If bt is on, the bt light blinks wether the device is connected (via usb or power charger) or not connected.
no
It's not the light but the icon
I have similar problem with my T-Mobile MDA Compact!
1. I switch on Bluetooth. The blue light is blinking and bluetooth icon is blue.
I wait few seconds and click on the bluetooth icon.
But T-Mobile MDA Compact is freeze. I can't operate with device anymore.
(I can't press hard buttons, i can't use stylus, i don't have connection
to my bluetooth handsfree Motorola H3).
2. I connect my MDA Compact to PC with USB cable. I switch on Bluetooth.
Everithing is OK! I have bluetooth connection to my PC, to my Motorola H3!
P.S.
Bluetooth handsfree Motorola H3 is ok. I have tested it with other mobile phones and PC.

BT Auto Switch

Hi!
I use BTHTools with my Himalaya for automatic switching of BT on/off.
It turns the BT ON if necessary (ex. incoming/outgoing calls), and turns it OFF when done. Good for saving battery.
Works also for other BT use, such as BT GPS, BT via Activesync, BT file transfers, etc., turns BT ON, keep it connected and automatically turns OFF for about one minute after connectivity is lost/ended.
However, it does NOT work with my Hermes.
Is there a similar application for Hermes? Moreover, it would be great if it would also automatically control NOT ONLY bluetooth but WIFI, GPRS and other connections as well. Similar to comm manager but automatic/timed.
Thanks.

Problem: When I turn ON the Bluetooth the pda automatically turn ON also the IR port

Hi,
I have a problem in may rom: When I turn ON the Bluetooth, the pda automatically activate also the IR port.
I found the problem using ActiveSync via BT. After the connection, when I open CommManager to turn off the BT I always found that IR port are ON.
The same problem if I manually turn on the BT through the Comm Manager.
Can anyone help me?
Thanks a lot

auto disconnect bluetooth after activesync

i had a asus ppc which auto connect and auto disconnect the bluetooth when i work with activesync over bluetooth. "connect activesync over bluetooth" and when i closed activesync the bluetooth closed too.
is it possible to get a solution for the HD for also auto disconnect after closing the activesync over bluetooth?
thx

Categories

Resources