Related
One can dial to a PBA phone stantion where you can reach people by dialing an extention. Say, it can be a firm with many fellow-workers with short local phone numbers.
The big-big problem is that the standard dialer that comes with T-Mobile MDA compact does not send DTMF tones correctly. I tried a custom dialer suggested here btw to replace the standard one and it worked fine. Unfortunately, this dialer do not satisfy me by some other reasons.
The question is:
Did anybody meet this problem and did anybody succeed to solve it? Say, by replacing the T-Mobile dialer by the CE dialer or something else?
In my Contacts in WM 2003 I used to be able to define an access number before I call my contact e.g.:
08707940000,,01xxxxxxxxx.
Where the first number is access number and the second is the contact's number.
However now, the phone only dials the access number (the first number) and after a short pause I can hear it dialling 3 to 4 DTMFs but it is not actually dialling them because the provider is not picking it up the DTMFs.
I have to dial the numbers manually and than its OK.
Can anyone reproduce this? Please help!
Same issue here... I have a contact like this:
+3493532XXXX,1234#,0561617XXXXXXX
This dials +3493532XXXX (my home number) where I have an asterisk box, then I hear the message "Please enter your password followed by the pound key" and the DTMFs for the password and # key are sent correctly (in the number the passwd is 1234), then I hear the tone where I can dial any number, I dial 056 (prefix to use FreeWorldDialout on my asterisk) and 1617XXX (USA Boston number)... I hear all the numbers, but I see my asterisk hanging up before the whole number has been sent.
Very weird... I will do some more tests to see if I can find any solution...
Ok, finally I got the solution... do not put more than 4 digits without a comma (pause)... i saved my contact like this and now it enters the password and dials correctly:
+3493532XXXX,1234#,056,1617,XXX,XXXX
Hope it helps you too! :shock:
I did what you did, the problem seam to be that the DTMF tones are not sent at all aldough I can hear them.
I'm getting this too very odd. Getting rather bored of holding the phone up to my speakers so I can play the right tone and empty my voicemail box!
hi.. got my vario II on friday, and i have the same problem. i used to be able to dial an international number on my UNIVERSAL by calling the local access number and insert a pause before dialing the international number for example: 02071246666,006596454343. however, this does not work on vario 2 and i am very upset about it!!
Hi,
you have checked this:
HKLM\Drivers\BuiltIn\RIL: EnableDTMFSupport = 0
switch to
EnableDTMFSupport = 1
Hi,
Thanks for the help, but i tried that, but it was already set to "1".. i switched to "0", soft reset, switch back to "1", soft reset again, but still not working...
I am also having this problem, cannot empty voicemail at the moment.
I have the same problem on my Vario II. When I'm entering the number manually during the call I can hear the sound, but the other end does not respond to my input at all.
This is really annoying as I can't get into my voicemail or contact customer service
Anyone had a solution for it so far?
Are there more people with a TyTn/Vario with this problem? If so, do respond because it might be a bug or something...
Motje said:
This is really annoying as I can't get into my voicemail or contact customer service
Click to expand...
Click to collapse
On my Vario II if I go to the phone app dial 150 and when connected then press keypad I can then navigate the customer service menus by pressing the on screen number keypad if that is what you mean?
Yes, that is exactly what's not working for me. I can press the keys during the call, and I hear the tone, but somehow the other end does not get them.
Interesting topic I just saw on MoDaCo: http://www.modaco.com/Problem-with-Phone-Dialer-on-Hermes-t247377.html
It turns out that it is not just the DTMF, but also the d-pad up key not going to the call history, and the 3G icon having changed to U.
This all happened after a hard reset.
Can anyone else who did a hard reset confirm if they have any of these problems?
Check that
HKLM\SOFTWARE\HTC\3GVTEngine\AMRDTMFToneFile = "\windows\dtmf122.amr"
then try changing the value of
HKLM\SOFTWARE\HTC\3GVTEngine\UseAMRDTMFTone
from 1 to 0 or 0 to 1
No idea what it means, but it is set up in some Preconfig setups
Excellent, I solved my problems. What I did was re-install all the cab files from the extended ROM. This gave me back my T-Mobile dialer and also made the DTMF working again.
Motje said:
Excellent, I solved my problems. What I did was re-install all the cab files from the extended ROM. This gave me back my T-Mobile dialer and also made the DTMF working again.
Click to expand...
Click to collapse
That worked for me to.
Mine worked fine untill I installed the DeepOcean dialler skin and then it stopped working - removed it and it came back (DeepOcean lacked smartdial).
Installed the Eten dialler and smartdial, and have lost the tones again, think this phone skin is great, but it won't properly uninstall (need the original T-mobile phone skin/graphics) so am currently stuffed!
Have done all the usual soft reboots etc.
I'm confident if I re-instated the deafault t-mobile dialler it would come back, however, I don't want to do a hard reboot and reinsatlll all the add-on apps and data.
Any ideas how to get the DTMF tones working - I can 'hear' them, they are clearly not being sent, If I put it on speaker phone, then in clear conditions the mike picks it up and it works!!
Any ideas?
DTMF Doesn't work - FIXED IT!
Fixed it!!
Editing the registry and setting the value to 0, then soft reboot and dtmf tones are working.
Setting it to 0 wasn't the obvious choice, and previously I hadn't soft rebooted.
Found the following from dhushy in:
http://forum.xda-developers.com/showthread.php?t=276700
Worked it out. For anyone with a similar problem, use the registry editor to locate the following key:
HKLM,"Drivers\BuiltIn\RIL","EnableDTMFSupport",0x0 0010001,1
Change the value from 1 to a 0 and Bob's yer Uncle (for non-British readers that means everything will be cushty - see Only Fools and Horses for a contextual translation)
Did this and I was able to manipulate my voicemail messages as normal.
Click to expand...
Click to collapse
I am on T-Mobile UK.
A Big Thank you
This advice on changing the dtmf code from 1 to 0 was the thing ive been lokking for - for the last 4 months. A really big thank you
Hi All,
Great site!!
I have 2 questions:
1 - When I use smart dialing from my hermes I use the direction arrows once I have found the contact and choose the work number of a contact that has an extension as +1 (999) 999-9999 x 9999 I then get a dialog saying "Invalid entry, please try again."
This same entry dials fine from speed dial or dialing from contacts, any suggestions, it's a real pain to manually dial the whole number.
2 - I have my numbers in outlook 2003 and they are formatted with the +country code format, so all numbers have a + in front of them.
When I smart dial, I can't see the last number of the phone number it only shows
+1 (xxx) xxx-xxx
Again it's really annoying as the only way I can find the number is by dialing and I usually use the smart dial to find a phone number when I am looking for someone's phone number.
BTW I have tried to edit the number and remove the + but outlook put's it back. This is actually good when travelling.
Thanks in advance,
I apologise in advance if this information is somewhere on the site, I am not lazy and I did read quite a bit before posting.
ROM version: 2.15.502.3
WM5
on my outlook, I have the phone num , ext and the phone will dial and wait for pickup before dialing the ext.
of course, i am not using the country code feature, so...
I would be happy with that behavior.
If I could change the font to be smaller in the phone application at least I could see the whole number.
Thanks for sharing.
Hi there, I'm wondering if anyone else might be having a similar problem with 'caller [or texter] ID'.
Most networks, as I understand it, use the international dialing code when sending out texts and calls, meaning this is usually the incoming number when you recieve a text or call.
I've obviously got people programmed into my contacts who text me but when they do, I don't get their name, I get their number - with the dialling code eg. +447750500500. When I tap to go into the threaded mode, I'll get all previous contact with this person but with them identified only as the number. However if I head to the People tab, then again to see the messages I've sent/recieved with that person, I get the same messages only under the banner of their name and not the number.
I believe calls work fine with the code programmed in on their contact profile.
Anyone know why this is being caused?
I have the same problem. Both calls and text messages.
I don't think it matters if the international code is there or not.
Really frustrating not knowing who calls.
I've had this problem first time the device was initialized (right after opening the box). It might be caused by the fact I didn't have any SIM in it at that time, I'm not sure.
After a hard reset with a SIM inserted, everything started working as it's supposed to.
Hmm, I've changed the SIM, but I can't remember if it worked wih the first SIM card.
But a hard reset deletes everything, right?
There are a few things you have to be sure of:
Do not have double contacts, if you have a number (with and without operator/country prefix) twice in your list it will not show any name.
I don't know if this applies if you have a contact on your phone memory and on your sim card. I am sure it does have this problem if you have two contacts with the same number on the memory phone.
For some reason this is logic: On an incoming call, the phones checks it's phonebook and retrieves two numbers and then it does not know what to display, is it contact one, or two?
I hope this helps you out. I did not experience any problems (yet).
AndrewCZ said:
I've had this problem first time the device was initialized (right after opening the box). It might be caused by the fact I didn't have any SIM in it at that time, I'm not sure.
After a hard reset with a SIM inserted, everything started working as it's supposed to.
Click to expand...
Click to collapse
Try this....
1. Edit one "test number" in your contacts and remove international codes.
Just put that "test" tel number. without int. codes... And make sure that number is not stored nder another contact. (No duplicates.)
2. Then dial from that number and see if that tel# is identified. If you have just "0xx-123456" then go to #3.
3. Go to registry and change of the Caller ID match rule. (Minus one digit.)
Example: Caller ID rule:8 (Change from 8 to 7 or 6 to 5 .. trailing digits for Call ID match. )
* HKCU\Control Panel\Phone\CalIidMatch value:7
4. Restart and test again...
5. If its OK, than test with SMS.
6. If its OK again , put back your international codes and test again.
7. If not go to no.3
Hope this helps.
KraFT
samluke said:
Hi there, I'm wondering if anyone else might be having a similar problem with 'caller [or texter] ID'.
Most networks, as I understand it, use the international dialing code when sending out texts and calls, meaning this is usually the incoming number when you recieve a text or call.
I've obviously got people programmed into my contacts who text me but when they do, I don't get their name, I get their number - with the dialling code eg. +447750500500. When I tap to go into the threaded mode, I'll get all previous contact with this person but with them identified only as the number. However if I head to the People tab, then again to see the messages I've sent/recieved with that person, I get the same messages only under the banner of their name and not the number.
I believe calls work fine with the code programmed in on their contact profile.
Anyone know why this is being caused?
Click to expand...
Click to collapse
Hi guys!! i had this problem too but i have fix the problem. what i do:
!) i store all my contacts in my sim card and delete the contacts in the phone.
2)do a hard reset
3)upon doing the hard reset, the phone will prompt you on importing sim contacts and finding your service provider. select both and and press ok
4)now try to call from your house to your phone to do a check.
5)my problem was solved after this
hope it helps!
KraFT_mk said:
Try this....
1. Edit one "test number" in your contacts and remove international codes.
Just put that "test" tel number. without int. codes... And make sure that number is not stored nder another contact. (No duplicates.)
2. Then dial from that number and see if that tel# is identified. If you have just "0xx-123456" then go to #3.
3. Go to registry and change of the Caller ID match rule. (Minus one digit.)
Example: Caller ID rule:8 (Change from 8 to 7 or 6 to 5 .. trailing digits for Call ID match. )
* HKCU\Control Panel\Phone\CalIidMatch value:7
4. Restart and test again...
5. If its OK, than test with SMS.
6. If its OK again , put back your international codes and test again.
7. If not go to no.3
Hope this helps.
KraFT
Click to expand...
Click to collapse
What was happening to me before the reset was a bit different - the phone wasn't able to match anything at all - even a number called from the phonebook and stored in "recent calls" in EXACTLY the same way it's in contact, didn't match to the contact when redialed.
I think that something required for Caller ID to work gets done when the phone is first initialized, and that this step requires full access to the phone module (which the phone doesn't have without a SIM inserted and a proper PIN entered).
hi,
i encountered also that worry,
i set the HKCU\Control Panel\Phone\CalIidMatch value:9
my mobile phone number to test was stored as "06xxyyzzww"
and when i phone my diamond2 from that number
the caller id is recognized
(with showing as +336wwxxyyzz)
i tested from my home phone stored in contacts as 04wwxxyyzz
i rang my topaz its was identfied as my home,
(with showing as +334wwxxyyzz)
i am in france, + is for 00 ,our phone numbers are 10 digits long
(mobiles and "home") ,
to be joined from abroad, you have to dial +33+phone number WITHOUT the first digit "0")
so the "9" value i put in the registry
if it could help you
regards
Hi,
just stumbled over the same problem.
The old phone (HTC P330) resolved numbers from my used format 01234-56789.
Since my contacts are a mess, I have 01234-12345, +49-123456-456, +49 (0123)-456 and so on, it would be a great pain in my ass to switch every contact to +49123-456 (which the new phone resolved).
I compared the Registry-Entry from the P3300 with the TD2 and voila: TD2 was 12, P3300 had the value 8.
I changed the TD2 to value 8, reboot and now I'm happy again, the phone is getting used to my contact list
Regards
Heiko
Hi,
I'm experiencing the exactly same problem, that incomming calls or messages isn't shown by name, but only by number.
I'm all new to Windows mobile, but I tried downloading a regeditor, and experimented with different values in the CallIdMatch string. However, no succes.
I live in Denmark, where numbers look like +4512345678, where +45 is the international code. Can someone please tell me, what should be the correct value? The original values was 8.
I have further found that some contacts are recognized. What the difference is between the groups, are however unclear!
Caller ID problem, my solution
I had the same problem. But after a hard reset it seems to work just fine now. Remember to backup your downloaded programs etc before doing this.
Tyven said:
Hi,
I'm experiencing the exactly same problem, that incomming calls or messages isn't shown by name, but only by number.
I'm all new to Windows mobile, but I tried downloading a regeditor, and experimented with different values in the CallIdMatch string. However, no succes.
I live in Denmark, where numbers look like +4512345678, where +45 is the international code. Can someone please tell me, what should be the correct value? The original values was 8.
I have further found that some contacts are recognized. What the difference is between the groups, are however unclear!
Click to expand...
Click to collapse
Hi,
"8" should be the good figure for you, as in France
we have phone numbers +33987654321
and "9" is the good value for me, in:
HKCU\Control Panel\Phone\CalIidMatch value:
Edit: i remove previous "edit"
in fact all my contacts had been erased" so it was normal to have no caller ID?
ps: is your carrier sendind all the figures when you're receiving calls, i mean +4512345678
so perhaps you're encountering a bug .
you should try to backup your device, with a soft like spritebackup(special price for htc owners on their webpage) and experiment an hardreset
and restore
regards
Hi ,
did you ever try to change the following:
RegistryEdit and Decreasing the CallIDMatch from 12 to 7 solved my Issue
See below
HKEY_CURRENT_USER\ControlPanel\Phone" name="CallIDMatch"
Greetings from Slovenia
Hello,
that is my first post so please do not be very critical to my english level and PPC skills .
now this is an old thread but for BULGARIA the correct registry value is "9". Here the mobil numbers are as follows "08xx 123456" (9 digits without the ZERO at the very beginning). that is why the usefull number is that (default for my TD2 was 8). Now after this fix the phone can correctly identify which number i want to dial when i am inserting it by digits, instead of selecting the exact person. i do not know am i explaining correctly but i will try to put some more detail on that. When i want to dial some particular number (for example "08xx 123456") the phone select me the correct contact no matter how i put this contact in memory. with "+3598xx 123456" or only with "08xx 123456". before that intervention the phone identifies me the correct contact only if i type the digits, exactly the same way that i have added it to the memory. So i think that this registry key does not have a universal resolution. the resolution depends on how many digits is using tha particular mobile operator.
i hope that will be helpful for someone who is happy to own an HTC and is happy with it ... like Me
Strange question - but I knew that there was probably very little chance for an answer except by those most expeienced with ROM flashing ...
I currently have Leo's ROM and have now noticed that when I get a text message with a phone number in the body of the text (my answering service uses this method to page me now) that something has changed.
If I get a message to call " please call 123 345 7777" there is no way to just touch the group of numbers and have the phone call 1233457777 - basically with one touch dialing. The system seems to divide things up to 3 different groups - 123 or 345 or 7777.
It does seem to still work if the text comes in this format - " please call 123-345-7777" , but I can't be assured that the many different operators will send via that format.
Since I have only had this problem since switching to my Leo HD2 and using a particular ROM I wondered if it might be a registry setting and if anyone else had noticed this ??