Related
I found a lot of posts where people ask for auto disconnect. My problem is the other way round: When I connect with GPRS after some 5 minutes or so my QTEK S200 disconnects by itself. This might be caused by the cab file MP_autoDisconnect_EnableDRM_prophetUA(AKU2.0)_060112.cab which I found in enhanced ROM?
I don't want to hard reset to see the effect this cab not beeing installed. Any ideas to help???
I have the same problem... lets see if anyone knows how to enable GPRS for longer then only 6 minutes.
I have the same problem... lets see if anyone knows how to enable GPRS for longer then only 6 minutes.
it's because of your mobile operator. i've the same sh.t here. it keeps disconnecting after 5-10 minutes and the traffic rounds up. and i have to pay more... i've a hima, my friend's SE W800 - same crap, keeps disconnecting. i'm sick of GSM networks, they're getting old and do not meet modern speed and reliability requirements. so i'm afraid we'll just have to wait until WiMAX or something else comes to replace an old man. cheers
You might wanna try this from wiki here:
If you want your GPRS (or EDGE) connection to always be on, set the following:
HKLM\Comm\ConnMgr\Providers\{7C4B7A38-5FF7-4bc1-80F6-5DA7870BB1AA}\|gprs connection name|\AlwaysOn = 1 (DWORD decimal)
And to turn it off:
HKLM\Comm\ConnMgr\Providers\{7C4B7A38-5FF7-4bc1-80F6-5DA7870BB1AA}\|gprs connection name|\AlwaysOn = 0 (DWORD decimal)
Note that |gprs connection name| will depend on the name you've given your GPRS connection
I'm on tmobile web n walk, so its a pain to wait for gprs to reconnect everytime.... I've just started using this for about a day, but looks ok so far... try it... see if its the magic ur looking for
zep said:
it's because of your mobile operator. i've the same sh.t here. it keeps disconnecting after 5-10 minutes and the traffic rounds up. and i have to pay more... i've a hima, my friend's SE W800 - same crap, keeps disconnecting. i'm sick of GSM networks, they're getting old and do not meet modern speed and reliability requirements. so i'm afraid we'll just have to wait until WiMAX or something else comes to replace an old man. cheers
Click to expand...
Click to collapse
I don't think it's connected to the provider as I know enough people using the same provider where GPRS stays connected a long time. The only difference we have is the PPC. I will try jamichy's solution later this week when I will be back home. In the meantime Craic Dub - does it solve the problem on your side?
jamichy said:
You might wanna try this from wiki here:
If you want your GPRS (or EDGE) connection to always be on, set the following:
HKLM\Comm\ConnMgr\Providers\{7C4B7A38-5FF7-4bc1-80F6-5DA7870BB1AA}\|gprs connection name|\AlwaysOn = 1 (DWORD decimal)
And to turn it off:
HKLM\Comm\ConnMgr\Providers\{7C4B7A38-5FF7-4bc1-80F6-5DA7870BB1AA}\|gprs connection name|\AlwaysOn = 0 (DWORD decimal)
Note that |gprs connection name| will depend on the name you've given your GPRS connection
I'm on tmobile web n walk, so its a pain to wait for gprs to reconnect everytime.... I've just started using this for about a day, but looks ok so far... try it... see if its the magic ur looking for
Click to expand...
Click to collapse
O.k. I couldn't wait and tested today. Now the connection seems to stay as long as you do not stop it.
But: It connects automatically to GPRS when you connect the phone to your provider. That's not really what I wanted. In other countries this will create extreme roaming costs.
Any other idea on how to stop this auto connect? Even using phonealarm's "do not start GPRS automatically" does not help, again it starts connecting when you dial in your Phone PIN.
:?
Seems the Reg Hack is not a brilliant idea... I have setup my device to power off display after 2min... when i press power button to come out of standby, it freezes the device for abt 40 to 50 sec
Its worse when i get an incoming call, the screen is on but does not respond to touch or pressing green button...
So i changed registry back... and bingo, everythings ok again....
But now, i've found another way, a little freeware app that does all I want and more, and you get the option to choose connect gprs on boot or connect when needed... etc... take a look at:
http://www.gb-soft.cz/XDAII/product_gprs_tweak_wm5pe_en.htm
I'm using now, and seems ok
jamichy said:
:?
Seems the Reg Hack is not a brilliant idea... I have setup my device to power off display after 2min... when i press power button to come out of standby, it freezes the device for abt 40 to 50 sec
Its worse when i get an incoming call, the screen is on but does not respond to touch or pressing green button...
So i changed registry back... and bingo, everythings ok again....
But now, i've found another way, a little freeware app that does all I want and more, and you get the option to choose connect gprs on boot or connect when needed... etc... take a look at:
http://www.gb-soft.cz/XDAII/product_gprs_tweak_wm5pe_en.htm
I'm using now, and seems ok
Click to expand...
Click to collapse
Sounds interesting. Still difficult for me to understand what it really does:
- What means "search GPRS [G] on start radio"
- What means "start [G] on start GPRS
- What means "Switch GRPS always On/Off hold till for following connection"
Can you tell me what it does non your side? Im a startting to hesitate trying to many things. I am still not convinced of WM5 - I installed GPS pgrs monitor (on QTEK CD...) which did not work together with phone alarm. And to deinstall was the ususal WM5 hassle, only using sktools and manual deletion of a file after another soft reser I was able to remove it again
Search GPRS ON start radio=gprs connects on startup
Start G on start GPRS=gprs connects when an application needs web connection, and stays connected
Switch GRPS always On/Off hold till for following connection=default settings, connect when needed, then disconnect
Havent had the phone freeze problem, and gprs connects on startup, and stays connected... which is fine for my tariff, tmobile web n walk unlimited gprs
jamichy said:
Search GPRS ON start radio=gprs connects on startup
Start G on start GPRS=gprs connects when an application needs web connection, and stays connected
Switch GRPS always On/Off hold till for following connection=default settings, connect when needed, then disconnect
Havent had the phone freeze problem, and gprs connects on startup, and stays connected... which is fine for my tariff, tmobile web n walk unlimited gprs
Click to expand...
Click to collapse
Seems to work flawlessly so far on my S200. Thanks for your help Jamichy!!
The only thing I'am still missing is EDGE in Germany... :wink:
I am having quite a small, but annoying problem with my S100.
I need to use 2 GPRS connections. One for my vodafone Push mail, and one for normal webbrowsing. I need to switch these 2 connections everytime.
That's not a real big problem, but point is, i cannot switch back. It cannot connect for an unknown reason ...
Totally shutting it down by entering Flightmode, does the trick. But entering and leaving flightmode is quite a hassle.
I do not believe it is an provider-issue, but an issue on my S100.
Are there programs that can turn off gprs just like flightmode, (but keep radio alive), and switch to another connection, and vice-versa? Or, solutions in registry or something?
I have a feeling the other connection is somewhat 'alive' so the new one won't work.
Did you tried with this?
Add a 'Disconnect' button (and Timer) to the "GPRS Balloon Tip"
To add a Disconnect button and a timer display showing how long GRPS is in use for the session:
HKLM\ControlPanel\Phone\Flags2 = 16 (DWORD decimal)
Guys,
I'm new on WM6 Professional and i780. I'm not able to keep wifi enabled when in standby mode. I've read a lot of thread but suggested tips does not work on i780.
ie
HKEY_LOCAL_MACHINE\System\CurrentControlSet\Contro l\Power\State\Suspend\{98C5250D-C29A-4985-AE5F-AFE5367E5006}
-change (Default) DWORD Dec to 1
HKEY_LOCAL_MACHINE\System\CurrentControlSet\Contro l\Power\State\Resuming\{98C5250D-C29A-4985-AE5F-AFE5367E5006}
-change (Default) DWORD Dec to 1
HKEY_LOCAL_MACHINE\System\CurrentControlSet\Contro l\Power\State\Unattended\{98C5250D-C29A-4985-AE5F-AFE5367E5006}
-change (Default) DWORD Dec to 1
On i780 the equipment freezes when turn on standby - I've to remove the battery to resume it.
It seems that this specific registry
HKEY_LOCAL_MACHINE\System\CurrentControlSet\Contro l\Power\State\Resuming\{98C5250D-C29A-4985-AE5F-AFE5367E5006}
-change (Default) DWORD Dec to 1
causes the hang. If I remove the registry the phone does not hang, but it turns off the wifi in standby.
I'm quite hungry; with my previouse I600 (WM6 Std.) this feature ran correctly.
Any ideas?
have a same problem too
-----------------------------------
PDA : DXHH1
Phone : DXHH1
Storage : SanDisk Micro SDHC 4GB Class 2
yunanda_keren said:
have a same problem too
-----------------------------------
PDA : DXHH1
Phone : DXHH1
Storage : SanDisk Micro SDHC 4GB Class 2
Click to expand...
Click to collapse
Karen,
after a lot of time I've solved upgrading to the official PDXIB1 - you can download from official Samsung site.
I'm using Communication Manager Pro to switch on Wifi at seleceted locations and select the option to keep the state in suspend mode, too.
bye
Use AdvancedCon for that
what version of communication manager pro did you use?
i get "windows refuses to open commmgr.exe applet(2)" when i try access wifi setup
i have a i780 and i want to keep wifi alive while in standby mode.
i have tried all the programs like CommMgr pro, advanced configuration, pocket toolman. i even tried diamond tweak and HD tweak. those programs all worked and kept wifi alive, BUT no data can be transferred to or from the phone.
i can ping my ip address from the phone, BUT no other ip address. the wifi is kept alive but something is stopping the data.
if i turn wifi off and then turn back on again, it works propperly, but as soon as it goes in standby no data can get in or out.
it seems it keeps wifi alive, but not all of things needed to fully work.
ive tried different ROMS, ive upgraded to the latest DXIB1. and i even tried a WM6.5 ROM and they all have the same problem.
anyone got any ideas?
http://forum.xda-developers.com/showthread.php?t=483149
if i use dont sleep, i will need an app to turn screen off after an amount of time too, because if i turn screen off with a program, when i get a sms or phone call it turns screen on and doesnt turn off again and battery drains really quick.
if anyone has been able to keep wifi alive in standby mode on a samsung i780 can you please specify the:
phone version
pda version
wifi s/w version
and what software used to keep wifi alive and/or registry settings changed.
and maybe the original phone and pda version. i dont know if this makes a difference. mine came with i780PCEHI2, ive changed different versions and different roms, i still have an IP address and can ping myself, and the phone thinks its on the wifi network. but it still doesnt allow in comming or out going wifi data.
anyone with a i780 and might not use wifi that much, would you be able to kindly test it, thanks.
Definetely working methode I have found by experiments to keep wifi on on i780:
[HKEY_LOCAL_MACHINE\Drivers\BuiltIn\SWLD24SP]
add "IClass"="{A32942B7-920C-486b-B0E6-92A702A99B35}"
[HKEY_LOCAL_MACHINE\Comm\SWLD24SP1\Parms]
"SetHostWake"=dword:1
"wakecondition"=dword:0 (0,1,2,3,4 all working differ ways)
[HKEY_LOCAL_MACHINE\System\CurrentControlSet\Control\Power\State\Suspend\{98C5250D-C29A-4985-AE5F-AFE5367E5006}]
"Default"=dword:0
Now after SR, wifi keeps connected in standby.
Hi there,
Does anyone know if it is possible to have the phone turn off the data/3g portion when not used in X amount of minutes? I know for WIFI it is possible but not sure if data/3g is possible?
Also, it seems when i have wifi and data on, the phone would use 3g over the wifi in OPERA or even updating weather in SPB mobile shell. Is this normal? Anyway to make it so WIFI is first priority over 3G?
Thanks
not normal, the phone should use the wifi first then the 3G.
ps. would be cool if an app or registry hack could switch off 3G when not in use.
I get the same issue with the WiFi not being prefered with SPB weather and also a hotmail email account. I was going to play with "NoData" but would be interested if theres a better solution
Couldn't find a better solution, I made sure to turn of HSDPA in the phone settings, change my network to GSM, then use "NoData" because I don't have a data plan. So far no extra charges.
Try the
GB-SOFT GPRS Tweak (EDGE+UMTS+3G) for WM6.1 - HTC Diamond
found in http://forum.xda-developers.com/showthread.php?t=407264
I installed it on my Xperia and it worked.
try bandswitch.....
Does turning off/on the data/3g part harm the hardware in any way?
HKEY_LOCAL_MACHINE\Comm\ConnMgr\Planner\Settings\
•
SuspendResume = GPRS_bye_if_device_off
•
CacheTime = xxx (where xxx are seconds before auto disconnect, the best value is 60)
after editing registry with this values it should hang up the connection after an specific amount of time without data transferred
Advance config in more setting connection you have the option
I'd like my phone to use the data connection to download weather info etc., but I'd also like it to turn it off when idle to save power. Is there an app to do this?
thanks
Click on the 3G icon on the top bar, then when the notification screen opens click on the 3G icon again, that opens the Comm Mgr screen, turn off the data connection.
OR, are you wanting an app that will do it automatically after XX min?
It should automatically disconnect after usage. I find my data connection active for like 23 hours and such. Big battery hog when it isn't even being used.
On my Fuze, there was a registry edit which would set your END key to disconnect a data connection while on the homescreen in the default position. Worked really well except it doesn't work on my new AT&T Pure for some reason.
A single tap would work exactly like the END key currently does. Pretty nice.
Code:
[HKEY_LOCAL_MACHINE\ControlPanel\Phone]
"Flags2"=dword:0000000A
Flags2: "Enables a disconnect button for GPRS connections to appear in the connectivity list. Also enables End key to disconnect GPRS."
[EDIT]
Actually it may still work. I just found that further down in my app.reg of my Custom folder, I had it set again, to 16.
[EDIT2]
Yup. Changing the value to A (A=10) works like a champ. It doesn't affect any normal End key functions either.
Alternatively, if you have TD2 Tools (which you should, great program), then under the Power tab, there is an option to 'Auto D/C Data Connection'. At least there is in 2a, v 2.0.3552.42948.
Yes, I want an app to disconnect the data connection after a few mins/secs. It should save power.
I will try the TD2 tools, I already had it but never thought about looking if it had this option built in.
Thanks to you all!
EDIT: It worked, it disconnects after a few minutes now. Does anybody know how to disable wake device when receiving SMS? The option is turned off, but still the device wakes itself.
arrow224 said:
Alternatively, if you have TD2 Tools (which you should, great program), then under the Power tab, there is an option to 'Auto D/C Data Connection'. At least there is in 2a, v 2.0.3552.42948.
Click to expand...
Click to collapse
player911 said:
It should automatically disconnect after usage. I find my data connection active for like 23 hours and such. Big battery hog when it isn't even being used.
On my Fuze, there was a registry edit which would set your END key to disconnect a data connection while on the homescreen in the default position. Worked really well except it doesn't work on my new AT&T Pure for some reason.
A single tap would work exactly like the END key currently does. Pretty nice.
Code:
[HKEY_LOCAL_MACHINE\ControlPanel\Phone]
"Flags2"=dword:0000000A
Flags2: "Enables a disconnect button for GPRS connections to appear in the connectivity list. Also enables End key to disconnect GPRS."
[EDIT]
Actually it may still work. I just found that further down in my app.reg of my Custom folder, I had it set again, to 16.
[EDIT2]
Yup. Changing the value to A (A=10) works like a champ. It doesn't affect any normal End key functions either.
Click to expand...
Click to collapse
Are both working on a TD2? I mean either the registry tweak or the TD2 Tool?
I personally prefer the reg tweak, however I don't understand the content of your EDIT note: "changing WHAT to 16"?? and your EDIT2 note : "changing the value to A" is in hex or dec? And do you mean that pressing the END hardware key will disconnect data connection now?
Hi
The data connection being on does not drain the battery. You have a network connection to the cell all the time otherwise you wouldn't receive phone calls, the data connection symbol just means your phone also has an IP address, that doesn't take any power.
If anything the connection remaining on saves power as each time you need a connection one doesn't have be created. Creating a connection uses more CPU cycles and radio power talking to the cell to open a network connection and then more to drop it.
The network operators also want the connection to remain on as it is less load on their networks than having them continually created then dropped.
More info here: http://blogs.msdn.com/windowsmobile/archive/2006/07/14/666203.aspx
Regards
Phil
you just need to modify these two entries (was written here many times)
Hkey_local_machine\Comm\ConnMgr\Planner\Settings
1. Change in CacheTime DWORD Data to 15 (Base is Dec value)
2. Change in SuspendResume the value to GPRS_bye_if_device_off
Make a soft reset.
The data connection should turn off after 15 sec if idle. It should also turn
off after you press the red key, or turn off the screen.
Try it.
Both solutions (reg mod and TD2 Tools) work most of the time, they are in fact the same. However I noticed 2 curious behaviours in which the timeout is not respected.
1) When I update weather via DataConnection, it does not autodisconnect after the preset time...it will when device goes in standby mode.
2) Data Connection stays on until Opera is open (even if not used).Once closed, timeout starts, and it's not that bad after all.
Can anyone confirm?
I used the TD2 tools, and i'm not experiencing these issues.
PhilipL said:
Hi
The data connection being on does not drain the battery. You have a network connection to the cell all the time otherwise you wouldn't receive phone calls, the data connection symbol just means your phone also has an IP address, that doesn't take any power.
If anything the connection remaining on saves power as each time you need a connection one doesn't have be created. Creating a connection uses more CPU cycles and radio power talking to the cell to open a network connection and then more to drop it.
The network operators also want the connection to remain on as it is less load on their networks than having them continually created then dropped.
More info here: http://blogs.msdn.com/windowsmobile/archive/2006/07/14/666203.aspx
Regards
Phil
Click to expand...
Click to collapse
This is good advice. Has anyone every experienced more battery drain if the the data connection is "left open"?
In any case, even if you "disconnect" data every time, if an app wants to access the internet, doesn't wm reconnect automatically again? (unless you use modaco "nodata" app or similar to inhibit it)
Didn't notice more battery drain with a data connection left open and you're right: if an app needs connection then it will automatically be opened. In my case I want auto disconnect because, even though I have 400 monthly prepaid connection hours, which is enormous for a phone, it annoys me to waste them while topaz is in my pocket.
Wow, thaks for the great tip Phil!
I have a prepaid 150MB limit, so it shouldn't bother me leaving it on. The 400 monthly hours sualc mentioned is indeed more of a problem.
BumAround said:
Are both working on a TD2? I mean either the registry tweak or the TD2 Tool?
I personally prefer the reg tweak, however I don't understand the content of your EDIT note: "changing WHAT to 16"?? and your EDIT2 note : "changing the value to A" is in hex or dec? And do you mean that pressing the END hardware key will disconnect data connection now?
Click to expand...
Click to collapse
The problem mentioned above, about auto-disconnecting when programs are being used... this is why I program my reg edit to manual disconnect.
@BumAround: Set the value to "0000000A" (which is hex). "16" was my default value, which was also Hex.
This will do 2 things. It creates a "Disconnect" button from the PopUp Connection window and also allows the END key to disconnect only while at the Today screen in it's default position.
For example, if you are browsing Opera and press the END key... it will only take you back to the Today screen and won't touch your data connection. If your at the default position (the Clock tab on both Manila and Titanium), pressing END again will stop the data transmission.
It is a very good solution to the OP's problem by allowing you to disconnect the data connection easily, at will, and without the need for extra programs.
player911 said:
The problem mentioned above, about auto-disconnecting when programs are being used... this is why I program my reg edit to manual disconnect.
@BumAround: Set the value to "0000000A" (which is hex). "16" was my default value, which was also Hex.
This will do 2 things. It creates a "Disconnect" button from the PopUp Connection window and also allows the END key to disconnect only while at the Today screen in it's default position.
For example, if you are browsing Opera and press the END key... it will only take you back to the Today screen and won't touch your data connection. If your at the default position (the Clock tab on both Manila and Titanium), pressing END again will stop the data transmission.
It is a very good solution to the OP's problem by allowing you to disconnect the data connection easily, at will, and without the need for extra programs.
Click to expand...
Click to collapse
Wow! Cool! You mean pressing END (hardware) key twice, once to bring the phone to the Today main screen, and one more time to disconnect data connection at will? Sweet!
Hi Sualc, the same "problem" for me updating weather (using option for data connection inTD2 Tools)
Not sure
PhilipL said:
Hi
The data connection being on does not drain the battery. You have a network connection to the cell all the time otherwise you wouldn't receive phone calls, the data connection symbol just means your phone also has an IP address, that doesn't take any power.
If anything the connection remaining on saves power as each time you need a connection one doesn't have be created. Creating a connection uses more CPU cycles and radio power talking to the cell to open a network connection and then more to drop it.
The network operators also want the connection to remain on as it is less load on their networks than having them continually created then dropped.
Regards
Phil
Click to expand...
Click to collapse
Not sure about this... and forgive me if I shouldn't be commenting because I'm referencing a cdma HTC touch pro 2, but I think this aspect is common.
My understanding is that the arrows up in the status bar should show white when a data connection is active and transferring data, but should turn gray when the connection is connected but not actively transmitting data. On my TP2, the data connection always shows the connection active and transmitting (the arrows stay white and never turn gray). I'm thinking if this is happening, one must surely be eating battery that isn't necessary.
On a cdma phone, the GPRS registry setting that is mentioned in this thread won't work because, although it will make the data connection automatically disconnect after an active data session, and you can change how long that time is with the CacheTime registry setting, unfortunately, on my HTC touch pro 2 Sprint cdma phone, you can't answer incoming calls when a data connection is active using these settings. I have to change the GPRS setting to #777 instead to be able to answer incoming calls when a data connection is active.... and with the #777 registry setting, I then loose the automatic time out and turning off of the data connection, so it stays on and showing active unless I turn it off manually and even then it comes on by it's self so often it's not even worth turning it off manually.
If any of you tech wizards can find a way for me to both be able to answer incoming calls when the is an active data connection, and also have the data connection time out and turn off automatically when not being used, I'd love to see it, because it sure seems to me I use more battery when I'm not turning off my data connection a lot manually, but it gets old always having to turn it off too!