Related
Hi Friends,
My new mobile phone SPV M600 got stuck whil starting showing four lines of messages as shown below.
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 2.10.1.22
Can any one please help me in geting my phone to today's screen.
I also attached the screen shot for reference.
did you try a hard reset ?
Ya I tried both hard as well as soft reset but same screen is stuck again and agian.Can any one please help me in this regard as I am very new to PDA family.
Ok, first things first:
Since you are new to this, are you sure you preformed a hard reset?
It is done by holding power + camera + comm manager buttons (one on the right, two on the left) and pressing with stylus in the reset hole at the same time.
A message should appear asking you to press 'send' (green phone button) to confirm reset.
If this does not help, you may have a serious problem.
Please answer the following:
Is the device fully charged?
Phone will fail to boot if the battery is too low.
Did you install any software right before this happened?
This should have been resolved by hard reset, but just in case I am asking.
Did you change the ROM, attempted CID / SIM unlock?
This could require more serious measures than I can advise on.
I did exactly the same thing which you mentioned.But even then it is stuck at the same screen.
Ya u r right I unlocked my mobile using a software from eBay.The unlock was successfull and I tried to insert T-Mobile sim, it also captured the signal and I was able to make and recieve calls then after that I wantedly switched off the phone and then tried to start it, there got the problem.
Can any one help me in this regard please.
I am having the same problem, but my phone is not sim-locked.
I've got the same problem after attempting smart1_wm6_pp8mb.exe
I'm having the same problem with my G4 QTEK S200:
Attempted to upgrade to WM6 Rom using smart1_wm6_pp8mb.exe
After reboot the phone got stuck at the QTEK Screen
Tried Hard Reset (Camera+Power+Comm+Reset) followed the steps with the same results (bricked)
I also tried re-flashing the rom back to the factory one using RUU_Prophet_220734_2207114_024721_QtekWWE_Ship and ROMUpdateUtility-NoVendorID.exe in Windows Vista with WMDC (Windows Mobile Device Center v. 6.0.6873) and the phone in boot loader mode (tri color screen) with working USB cable, with windows firewall disabled and symantec AV disabled as well, RUU keeps saying error 260 "the update utilitiy cannot connect to your pda phone..." .
Do you think I should try this process using XP instead? No matter what i try i keep getting the error 260
Any help would be greatly appreciated
Got it fixed!
it was definately a Vista issue. once i tried it in XP with ActiveSync it worked like a charm and i got my phone back up and running. also used spb backup and restored all my settings.
ipl/spl screen
i got the same problem with new rom wm6, and the 260 eror, my problem is that i have xp and the activesync does`t connect ...
... means i cant redo the original rom ????
PLEAAASEEE HELPPPP !!
Again My phone SPV M600 got stuck at IPL/SPL screen
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
yekanth said:
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
Click to expand...
Click to collapse
A rom reinstall on xp solved my problems on that one. retry a couple of times! It may not work the first time! hard reset as well...
Try an official wm5 rom just in case
good luck
Can you please gimme step by step procedure
HI Phil,
I am new to these kind of installations . CAn you please Gimme step by step procedure for ROM installation.
mine is now also stuck, after trying to install new rom. wont connect to active sync either, have i fooked it? tried hard reset etc.
thanks
(with a turned off phone, press and hold camera button then insert USB cable)
then flash provider ROM
RECOVERING FROM ERROR IN STEP 8 WM5->WM6
1. Don't panic
2. Don't panic
3. Unplug the phone
4. Reset with stylus,and keep the Camera Button pressed.
5. A 3 color screen will appear(Bootloader Screen)
6. Connect your device with your PC,and run the NVID(no vendor) WM5 rom.
7. The device will be resetted after RUU(rom update utility)finishes
8. Repeat the WM6 upgrade,from STEP 5..
Click to expand...
Click to collapse
from here http://forum.xda-developers.com/showthread.php?t=310452
hi jay
i seen your post in n00b guys one, i fixed it!!!!, thank you so much, i couldnt remember how to get it to those 3 colours.
thanks again
Colin
Hi Iam unable to get the NVID ROM
Hi,
I am unable to get the NVID ROM. The Rapidshare link that has been provided in the other thread is not working. Can some one tell where can i get the ROM.
collywog19 said:
i seen your post ...
Click to expand...
Click to collapse
no problem mate.
..and yekanth i see what u mean about the dead links. i have the files on my computer at home but i'm posting from my prophet right now, so i can't upload. Try using the "pdaviet temp" from one of the wm6 threads?
(http://rapidshare.com/files/54265407/Prophet_PV_Temp.zip)
Hi Iam able to update the Rom but no use
Hi,
To mention my phone is from orange-UK. I got the orange rom from our FTP site and did the flashing/update what ever you say.But still it is getting stuck at the same IPL/SPL screen. Iam very much worried that I will not get a proper solution for my problem.It will be very grate full if some one resolve my problem.
just seems strange...how did you fix it last time? did it just start working again? A random guess would be that the camera button got liquid spilled on it or is stuck in.
If the camera button is pressed in the phone will go to 3 colour screen every time it is turned on.
It won't do any harm if you try to press/move that button to see if u can "unstick" it, not likely I think but u never know...
ok i have a issue with my fone my phone is stuck on the tri-colored screen which says:
TITA100
SPL-1.20.01ipro
well i am as u can see im not good with tech. stuff like this but i would like sum advice or ideas on how to fix my problem. well here is how it all happened. my fone started off fine, out of the blue it started turning off by itself, then coming back on. it will reboot fine then as soon as i touch the screen or try to text or call it shut off on me. first i thought my battery was dying. that didnt work kept it on the charger switched out the battery, still nothing ended up doing the same. so a fren told me to hard reset or press the ok button pwr n the reset button at bottom using the stylst. now im stuck in bootloader mode after i ran a program:
HARD-SPL-MFG
and was told to flash the fone, which i had no idea what to do the person who was helping me i didnt hear frm again n i was stuck in this tricolored screen what should i do? i just want my phone up and running so i can use it once again...if thats possible..it be great i love the phone n dnt want the money i invested into it wasted
thank you soo much,
If I had to guess, it sounds like you have installed a SPL that is not compatible with your existing radio and rom.
First thing is I would try downloading the stock rom for your phone, I believe you can download this from HTC's website, I would download the newest and the one prior to it. Try installing the older of the 2 first since your SPL that you do have is older, and if it fails to install, then try the newer of the two.
If it still fails, come back here and I'm sure somebody else can give you more advice.
BTC
As the title says, I have an Elf & when you press the power button (which is meant to turn the screen on and off) it shuts the device off instantly.
I first tried doing a hard reset
Then I tried another rom, to see if it was to do with the OS
& then I tried two other roms.
Ive still got the same problem.
Thinking of taking it back to the place I got it.
Anyone got any thoughts on any solution before I take it back?
Im thinking its a hardware problem that I cant really solve.
which spl are you using? I had a similar prob when i upgraded my rom to 6.1, but aftr using 3.07 spl, problems were gone..
I was using 3.07, but it doesnt matter now.
I took it back to the shop (with all accessories etc) and they replaced it for me. I feel bad about hastling them.
I took them an Elf, but apparently they have given me a Elfin, but on their system, they both just come up as p3450
But it works! thats the main thing.
and its gold and shiny.
Maybe somebody know how to solve this problem without turn elf back to the shop?)
I have same problem but haven't a chance to turn it back) 3.07 spl also
I had exactly this problem before I knew I have an Elfin.
I flashed Elf Roms on my Elfin, that caused the problem.
It boots regularly, but it will do a soft reset every X
minutes. Then I flashed an Elfin Rom and everything
works fine ^^
Maybe I'm wrong, but i think its Elf. It has 64Ram & 128 Flash, or they may not correctly view after flash or i dont understand differences?
It boots regulary every X minutes because it goes to sleepeng mode if device is not using. If this option off, it will not boot by its own, only if i press power button(
My Touch HD doesnt respond, it hangs and restarts itself all the time. Today it chrashed totally and I cant start it no more. It comes to the text "smart mobility" then the softwareinfo in the right lower corner pops up and nothing more happens..
I cant do a hardreset. (tried with volumebuttons and powerbutton at the same time)
I cant upgrade the software..
Anyone had this issue before?
Servicecentre?
Sad times...
Cokey,
Can you even put it into the bootloader mode?
Cheers.
Ehrm, whats bootloader mode?
hold vol down, and press power on (keep holding volume down until screen comes on)
you should see a screen of 3 coloured bars
if you can do this, you should be also able to do hard reset. for a hard reset make sure you hold both the volume buttons down, and keep them held after you press power on
Tom
Okey, havent tried that yet. But hardreset wont work, with both volumekeys and power on...
I've just tried that bootloader mode and that works but a hardreset isnt working. It starts up as written above then the display fades out a bit. Nothing more happens...
Darn it...
Cokey said:
I've just tried that bootloader mode and that works but a hardreset isnt working. It starts up as written above then the display fades out a bit. Nothing more happens...
Darn it...
Click to expand...
Click to collapse
Cokey,
All is not lost, don't worry. If you can get into Bootloader mode, then you will be able to flash a new ROM onto it. Go to the ROM section and follow crackwhore's very detailed guide.
Have fun flashing!
Cheers.
PoisonWolf said:
.
Click to expand...
Click to collapse
Thx for the help...
After maybee 20 hardresets starts it finally started...
All seems ok with it right now... Will leave it on over the night so Im sure it wont hang/restart again..
Again thx for the help..
(Flashing is something I wanna try but I really want my OS to be in Swedish )
I have the same issues. I am constantly reflashing the ROM because the phone will not last more than a day before being stuck on the Smart Mobility screen.
I have been flashing all of Dutty's different ROMs including LEO R4 and WM 6.5 R14 Turbo, WM 6.1 etc every day for the past week. It still freezes daily and when reboot, it gets stuck on Smart Mobility Screen. I am ready to throw it in the bin!
Anyone got any ideas. Flashing ROMs isn't working or fixing it as I have tried all sorts. I have also upgraded the Radio yesterday, still doesn't help. Tried also a new SD card, again, still freezes.
jchiou99 said:
I have the same issues. I am constantly reflashing the ROM because the phone will not last more than a day before being stuck on the Smart Mobility screen.
I have been flashing all of Dutty's different ROMs including LEO R4 and WM 6.5 R14 Turbo, WM 6.1 etc every day for the past week. It still freezes daily and when reboot, it gets stuck on Smart Mobility Screen. I am ready to throw it in the bin!
Anyone got any ideas. Flashing ROMs isn't working or fixing it as I have tried all sorts. I have also upgraded the Radio yesterday, still doesn't help. Tried also a new SD card, again, still freezes.
Click to expand...
Click to collapse
Have you tried reverting back to stock rom to see if problem persists? If so, return device under warranty
J,
USPL or HSPL? Do you install any applications, or do you leave it as it is and it still crashes in a day?
Cheers.
jchiou99 said:
I have the same issues. I am constantly reflashing the ROM because the phone will not last more than a day before being stuck on the Smart Mobility screen.
I have been flashing all of Dutty's different ROMs including LEO R4 and WM 6.5 R14 Turbo, WM 6.1 etc every day for the past week. It still freezes daily and when reboot, it gets stuck on Smart Mobility Screen. I am ready to throw it in the bin!
Anyone got any ideas. Flashing ROMs isn't working or fixing it as I have tried all sorts. I have also upgraded the Radio yesterday, still doesn't help. Tried also a new SD card, again, still freezes.
Click to expand...
Click to collapse
No luck
I think my warranty is out the window when I tampered with the screws and broke the VOID Warranty sticker.
I have used both USPL and HSPL and same issues occurs. I think I have narrowed it down... if I don't touch the onboard memory, ie not install anything to the onboard memory or touch it too much in that area, then it will tend to be okay. It starts to freeze and lock up at Smart Mobility Screen whenever I copy stuff or active sync etc.... so far anyway.
Looks like its going in the bin... last resort tomorrow, revert back to stock rom and see how long it lasts.
NOW ITS FIXED. THANKS
Dear all,
after experimenting quite a few cooked rom, my hd2 stoped working all on a sudden. When i tried to switch it on it came only the white screen with green htc written on it. And it (white screen) stucked and used to stay on. I took the battery off and switched on again it remained same. Just before a while i tried again, now the white screen coming for a second and no more pulse. Please advice me.
Thanks in advance.
Zaman
connect your phone to your PC via ActiveSync/WMDC and run your stock ROM and see if that helps...even with no ROM on the phone Windows should still show connected
http://forum.xda-developers.com/showthread.php?t=609477
*Go into BootLoader Mode (turn off phone, then press and hold the VOLUME DOWN then Press and hold the POWER button. After about 3 seconds the tri-coloured screen should appear). Verify the screen shows SPL-1.42.HSPL, which is the HardSPL version*
Click to expand...
Click to collapse
If you get tri-colored screen you can flash any ROM that you want without ActiveSync ... one of the advantages of HSPL if you have one installed.
Thanks again,
its not the tricolour screen.
It doesn't connect with the pc through active sync. As i tried to go for another rom after it got stuck.
Really worried a bit.
Sorry bro, i got it what you said. I got the tri colored screen after following your instruction.but its staying for a second and going off. I have done the hspl installed before. Any more advice would really be of very helpfull.
Thanks
Which ROM/radio are you using? If you've got HSPL installed it shouldn't be difficult to get it working again, you should just need to flash to a compatible ROM and radio.
[email protected] said:
Sorry bro, i got it what you said. I got the tri colored screen after following your instruction.but its staying for a second and going off. I have done the hspl installed before. Any more advice would really be of very helpfull.
Thanks
Click to expand...
Click to collapse
If you have HSPL and can see tri-color screen on display ... just plug in usb cable (that is connected to PC) in HD2 and start flashing process again the same way that you did before. I suggest you flash some of the official ROMs.
Thanks _x_
after having seen tricoloured screen i connected it with usb cable and flashed as normal. It did work for. And the phone is alive again.
Thanks to all of you for your attention and helps.
Cheers.
Glad I could help but it is "bepe" that you should thank to for HSPL
http://forum.xda-developers.com/showthread.php?t=611433
can you also change the thread title.. Add "Fixed"