this is my software :
ROM : 4.00.05 ENG
ROM Date : 06\05\03
Radio version : (EMPTY ......) blank !!!!
Protocol Version : (EMPY .......) blank !!!!
Identity : PW10A1
Platform : PocketPC
Imei : .........(Empty) Blank !!!!!
What should i do with this problem ??
thx
Is your pocket still doing it? maybe not! But this tells that your imei has been removed from your provider in most cases this is about stolen or lost items from your provider. In your case contact your povider and ask why your imei has been removed!![/img]
This appears to be a corrupt radio stack, have a good look around the forum, do a search on failed radio stack, or similar. That post about a provider removing the imei physically from a phone sounds extremely unlikely. A phone transmits the imei number when switched on, if the imei is on the blacklist for stolen/lost/barred phones then it is refused access to the network.
ow cruise yip your right, i wrote it wrong
mrgsm said:
this is my software :
ROM : 4.00.05 ENG
ROM Date : 06\05\03
Radio version : (EMPTY ......) blank !!!!
Protocol Version : (EMPY .......) blank !!!!
Identity : PW10A1
Platform : PocketPC
Imei : .........(Empty) Blank !!!!!
What should i do with this problem ??
thx
Click to expand...
Click to collapse
you need send to repair! or I can fix the problem!
Brother i am upgrading my device it stoped at 2% now its dead only goes to bootloader show
ipl 1.81.00001
spl 1.81.00001
i master reset but nothing happened i flash all roms on wiki nothing happened always say invalid tool
i need this rom because this has previous this
Rom version 1.8.415.2 wwe
Rom date 11-3-06
Radio 02.71.90
protocol version 4.1.13.31
EXT Rom 1.8.415.102
Thanks in advance who help me in this case
I have another set of that how can i read other set rom and flash in to that set
Was it CID locked? did you buy the phone r did you get it with a subsciption?
oddball1 said:
Was it CID locked? did you buy the phone r did you get it with a subsciption?
Click to expand...
Click to collapse
Not it is Not Cid locked & Also Not Sim Locked.. yes i buy from a shop in pakistan but when i upgrade i get problem
I also have bricked my Herald after upgrading to Aserg but nothing now ,,only green screen and off ...
it was CID locked
from Mobinil Plz Help
zubi1984: i had the same problem.
try mtty.exe (use wiki), and try the commands for it.
if it says something clearly, then you can -somehow- unbrick your device.
if it gives error..
-this happedned to me-
you should bring it to the service, with warranty.
if you are lucky, they will fix it to you without price.
i hope you have warranty, because the man in the service said that i really fuc*ed it up... the new motherboard would have been very expensive.. without warranty
so first of all, calm down, and let's start reading about the upgrade, read a lot, and go to another forums, maybe somebody can help to you unbrick your device
____
my device said:
error 30* invalid upgrade tool (for any roms)
only in bootloader mode running
hard reset failed
reset does not works
no charge lights on charge
mtty.exe error, commands: no answere.
pulyka
Hi pulyka, Can you Please tell me about commands for mtty.exe..what to write inside te command box exactly ,,
any more details about "mtty " would be thankful
for me:
Cmd>info 1
Invalid command : info 1
For a help screen, use command ? or h
Cmd>info 2
Invalid command : info 2
For a help screen, use command ? or h
_____________
this is wrong.
___
read it carefully!
http://wiki.xda-developers.com/index.php?pagename=Hermes_BootLoader
try it, but in your own risk..
unfortunately i am not an expert in this..
some people helped me in a hungarian forum.. and they said, my pda is bricked completely:S
if mtty working properly:
sb
I already connect to USB!
Cmd>info 0
GetDeviceInfo=0x00000000
Wizard
Cmd>info 1
GetDeviceInfo=0x00000001
2.21.0000
Cmd>info 2
GetDeviceInfo=0x00000002
+ SD Controller init
- SD Controller init
+StorageInit
***** user area size = 0x1EB80000 Bytes
HTCSWIZTMO07 â-r€HTCE
Cmd>info 3
GetDeviceInfo=0x00000003
this is died device:
info1
Invalid command : info1
For a help screen, use command ? or h
Cmd>info 1
GetDeviceInfo=0x00000001
2.24.0000
Cmd>info 0
GetDeviceInfo=0x00000000
Wizard
Cmd>r2sd all
***** user area size = 0x1DE40000 Bytes
R2SDBackup() - Download type = 5
usTotalBlock = 1 sizeof(SDCARD_SIGNATRUE_TABLE)=512
GetDeviceCID: Error - InitDecoder
GetDeviceCID: Error - InitDecoder
You didn't get the proper security level to download a specific image
Cmd>
pulyka
NO GSM FIX FOR SOME PHONES:
CLICK ON LINK
http://forum.xda-developers.com/showthread.php?p=2276981#post2276981
POST #56
I am making this thread so someone can please help us users of a HP hw6900 Series with the "NO GSM" startup message.
I have a HP hw6925, NO GSM, my product was under warranty and I recently sent it in to HP, , it would cost almost $300.00 for a new board, and I had the warranty at that time.
My next attempt to try and fix this issue will be what is posted at the link below.
If anyone out there has any "Sable" Backups, post in this thread, email me at [email protected]
I will post them on rapidshare, and alternate sites for everyone to download.
This is a huge problem. These HP hw6900 are nice phones, most of us still want to be able to use them as a phone, and a "PDA", some of us right now inlcuding myself can only use them as a PDA, or not at all, I will posting links later today, that should get any SABLE from the "Stuck on Bootloader Screen".
I am willing to donate to anyone who is serious about helping us fix this issue if it is possible, without replacing the mainboard of the hw6900, I will also be calling HP, and post the part number here and actual price for the hw6925 board.
"stuck On Bootloader"
If you are stuck on a HP Invent Screen, with G.39, etc.
And you have tried to hard reset and softreset with no luck, this is what you do.
XP Instructions:
1. Download this link http://www.mediafire.com/?3ygfbx0sjdy
2. In the taskbar area in the right hand corner, right click on activesync, bare with me, I'm using Vista and have to remember this, click connections..., you need to uncheck everything click ok or apply...
3. press ctrl-alt-delete, end process wscescomm.exe, (named something like that, end the process.
4. Extract the file you downloaded if needed.
5. Connect your device to the usb port on your computer.
6. Run Uni Exit Bootloader Application. Done
Vista Instructions:
1. Download these 2 links, and extract them if necessary.
http://www.mediafire.com/?3ygfbx0sjdy
http://www.mediafire.com/?9pmjkponfsg
2. Start Device Manager, (Start-Control Panel, Class View[Far Left Corner])
3. Connect HW6900 to USB port, you should now see a Mobile Devices (Next to + sign), Double Click
4. Right-Click on the Device, Click Update Driver Software, Choose let me pick from a list, Uncheck compatible hardware box.
5. Click have disk, Browse to location where USBAS is extracted, choose the wceusbsh.inf file, Double Click.
6. You should see Microsoft USB Sync, if not and it reverts back to the already installed file, and the box rechecks itself, uncheck it, choose microsoft, and choose the latest Microsoft USB Sync to install
GOOD LUCK
My Current hw6925 Status
"NO GSM" When Booting Up
I beleive it has No RadioOS.Nbf & No RadioFS.Nbf & No Imei.
Here is a screenshot of the Asset Viewer on the GSM Tab
Windows Mobile 6, Windows Mobile 6.1 Port
Official Windows Mobile 6/6.1 Port for hw6900 Series
Let's Get started people, Contribute to this thread.
If you have any Full Backup's of any hw6900 series thread post on rapidshare.com or mediafire.com
If you can not let me know by email, I will figure out a way to post them for you.
Again, any programmers willing to help any of us hw6900 Users, Please Help
Let me know the paypal account to deposit to via pm, I will post that information via this thread.
I need official 1.30 Cingular Roms from "Working" Devices.
If you can backup everything, including, RadioOS, RadioFS, CEOS, CEBL,
for those of you with fully working devices, please contribute to this thread.
Everyone please, I am trying not to wake up and see myself as the only one posting in this thread, I'm not the only one that wants this or the only one with problems with their hw6900 Series phone.
Please Contribute
HP HW6925 Repair Costs
Repair Cost $286.48 + Sales Tax.
Payment by Credit Card
Will take 3-5 Days,
I beleive they ship the box to you. (I think)
To much for my blood, May as well get a I-Phone
Hi,
I don't have any problem with my 6915 i have a french rom if you want and if you say me what i do to extract my rom i can upload everything to you
++
Radio Backup
dexxa05 said:
Hi,
I don't have any problem with my 6915 i have a french rom if you want and if you say me what i do to extract my rom i can upload everything to you
++
Click to expand...
Click to collapse
Do you have at least a 1 - 2 gb minisd card?
If so download mtty here
http://buzzdev.net/downloads.php?file=75
If you have Windows Xp, (CTRL-ALT-DEL) end process for wcescomm.exe (something like that).
put 6915 in bootloader mode, connect to usb port, press ctrl-alt-del, make sure activesync process is not running (WCESCOMM.EXE .......)
Start the mtty1.42.exe program
you should see:
USB>
now type
d2s 60000000 800000
If you have any problems please email me or im, [email protected]
Alot of people need this file, if possible, I am willing to even remote desktop connection, if you are unable to extract the radio rom.
Let me know what happens
i'd like to contribute what I can to this project I have an hw6955, when I went into bootloader to try to make a backup of my rom I get an error and it does not complete the process
jambongo said:
i'd like to contribute what I can to this project I have an hw6955, when I went into bootloader to try to make a backup of my rom I get an error and it does not complete the process
Click to expand...
Click to collapse
Do you get a "Cal Cheksum" on your Screen
try backing up your device using awizard tools, posted on here in the somewhere,
full backup including radio, ext rom, etc ........
then post it here
I will begin the Real WM6 Port
here's the message I get:
Code:
SD:Waiting for card insert.........
CMD3 for SD, it's OK, ready to get RCA from response.
SD:Detected one card
SD:ready for transfer OK
d.total_lba=1E4A00
d.block_size=200
d.RCA=E624
d.drv_type=40000000
d.busWidth=1
Total card size=3C940000
Read singal error D3
Read singal error!
SDCARDD2S+,cStoragePlatformType=FF
Some more info that may be useful:
Memory
System ROM Size : 128MB
System RAM Size : 64MB
ROM Is Flash : Yes
Flash Chip Type : G4
Flash Block Size : 256KB
PSM Driver Version : N/A
Version
Product Revision Level :
ROM Date : 08/28/06
ROM Revision : 1.52.00 ENC
Extended ROM Version : N/A
OS Version : Windows CE 5.1
Bootloader Version : G.39
XIP Version : 1.0.0.0
Camera
Module Present : Yes
Hardware Revision : 9650
Hardware Driver Version : 0.8.0
Software Driver Version : 4.1.0
Software Version : 1.0.21
Camera API Interface Version : 1.0.7
Camera Information : 1.3 MP 8X Zoom
Bluetooth
Radio Present : Yes
Firmware Version :
Hardware Revision :
Driver Version : 1.7.1.7800
Software Version : 1.7.1.7800
Wi-Fi
Radio Present : Yes
Firmware Version :
Hardware Revision :
Driver Version : 1.00.00
Software Version : 2.0.53
IP Address : Radio is Off
GSM
Radio Present : Yes
Radio Firmware Version : 1.02.00
Radio Protocol Stack Version : R5G.27.00.05
Radio Bootloader Version : 0.06
Radio File System Version : 0.07
Default Radio GDFS Version : 0.05
GPS
GPS Present : Yes
Status : GPS is Disabled
Manufacturer : Global Locate
Revision Level : N/A
Driver Version : 2.00
Firmware Version : 4.169.154.0
Software Version : 2.9.0.0
Awizard Tools
http://forum.xda-developers.com/attachment.php?attachmentid=26038&d=1138056282
Download the link above, then, run the program in windows 2000 compatibility mode, choose that by right clicking the file, click on properties, then, compatibility tab, check mark run in
compatibility mode, choose windows 2000, click apply ok, then run the program, choose the option for backup your device, backup everything choose [Y] or [YES] to everything, including radio, os, ext rom, .....
Follow the directions, beleive the device has to be connected to activesync, let me know what happens, any questions email, me,
Anyone else can do the same, lets fix these Sable devices, and start on a WM6 Port,
jambongo said:
here's the message I get:
Code:
SD:Waiting for card insert.........
CMD3 for SD, it's OK, ready to get RCA from response.
SD:Detected one card
SD:ready for transfer OK
d.total_lba=1E4A00
d.block_size=200
d.RCA=E624
d.drv_type=40000000
d.busWidth=1
Total card size=3C940000
Read singal error D3
Read singal error!
SDCARDD2S+,cStoragePlatformType=FF
Some more info that may be useful:
Memory
System ROM Size : 128MB
System RAM Size : 64MB
ROM Is Flash : Yes
Flash Chip Type : G4
Flash Block Size : 256KB
PSM Driver Version : N/A
Version
Product Revision Level :
ROM Date : 08/28/06
ROM Revision : 1.52.00 ENC
Extended ROM Version : N/A
OS Version : Windows CE 5.1
Bootloader Version : G.39
XIP Version : 1.0.0.0
Camera
Module Present : Yes
Hardware Revision : 9650
Hardware Driver Version : 0.8.0
Software Driver Version : 4.1.0
Software Version : 1.0.21
Camera API Interface Version : 1.0.7
Camera Information : 1.3 MP 8X Zoom
Bluetooth
Radio Present : Yes
Firmware Version :
Hardware Revision :
Driver Version : 1.7.1.7800
Software Version : 1.7.1.7800
MAC Address : 00-17-E5-A4-B3-97
Wi-Fi
Radio Present : Yes
Firmware Version :
Hardware Revision :
Driver Version : 1.00.00
Software Version : 2.0.53
IP Address : Radio is Off
MAC Address :
GSM
Radio Present : Yes
Radio Firmware Version : 1.02.00
Radio Protocol Stack Version : R5G.27.00.05
Radio Bootloader Version : 0.06
Radio File System Version : 0.07
Default Radio GDFS Version : 0.05
IMEI Number :
GPS
GPS Present : Yes
Status : GPS is Disabled
Manufacturer : Global Locate
Revision Level : N/A
Driver Version : 2.00
Firmware Version : 4.169.154.0
Software Version : 2.9.0.0
Click to expand...
Click to collapse
gave the tool a shot, but it gives me this error when it tries to backup the radio:
Code:
ERROR: ITTFFSGetInfo: outbuf==NULL
WARNING: using default 512 bytes for sectorsize
CopyTFFSToFile(0x50000, 0x280000, ROM\sable\sable-Radio.nba)
ERROR: ITReadDisk: outbuf==NULL
besides that no problems generating an OS and a boot.rgu image file
Okay, I'm also using a hw6915 with original german ROM, and I'm interested to get an to help getting WM6 on it.
Where is the problem? So many HTC devices have been got to run WM6. I thought the 69xx has also been built from HTC. Is there such a big difference, or is the "Sable" just a rarely used device so that no one knowing how to do is just doing it?
I am using the hw6915 with english uk original rom.I would like also to see the wm6 on my device..But the problem is that the developers will not fix a version for this device,because they are not interesting for this.We would be lucky if somebody of them had a device like ours and he had the grazy to make a version for this,for his own use,but they have Htc all of them and our mobile is old for their fancy now...Too bad..
any progress on this?
jambongo said:
any progress on this?
Click to expand...
Click to collapse
no progress at all, no one to help, or even a email reply back
my knowledge is limited in this area, but I am more than willing to help, I did provide a partial backup to you about a month or so ago
I'd still love to see a Windows Mobile 6 or 6.1 upgrade. I'm not sure how I could help. Does anyone else know why no one has cooked one up? I'm guessing no one who can owns one of these things.
I have a 6955 and will be doing a backup soon. I will post it as soon as I have it. Lets get things rolling.
This link should help with raw ROM dumps through the bootloader.
http://forum.xda-developers.com/showthread.php?t=325683
here is my problem
stuck in bootloader.
I have a HTC Athena x7500
Wend I turn on the device, it goes directly to bootloader and
the screen is:
ATHE 100
IPL - v1.00
ATHE 100
SPL-v3.05.0000 OR my old spl is 1.10
I have tried to change the language of my athena and then he died :spanish > fransh
USB (wend is to connect)
series (wend is unconnectable).
I can not turn the unit off by pressing the button, but must take
the battery.
I have tried with hardspl its not working
I want a solution in the forum xda-develop it says my q must upgrade to the rom of espana oficial
After downloading the rom:Advantage_HTC_SPA_2.21.412.1_1.50.00.00_Ship
I tried to upgrade to this rom May j has a mesage on my athena screen:
found spl v1.10
dowload Spl before v3.05 is not allowed! or on my pc has a mesage error 244 invalid model id
I tried to update it with the sd card i have the same mesage
upgrade with athenaUnlucker not work
upgrade with hardspl v7 not work
upgrade with CheetahUnlocker not work
upgrade with athena wraper not work
I tried to fix the problem with mtty
cmd> task 32
level=ff I board on my pda (cid locked)on the Spanish language HTC_304
Cmd> lnb filename.bin 76508000
invalid comand
or Cmd> lnbs filename.bin 75108000
Cmd>
no response
helpe me plaise::crying:
it's been two year since I looked for a solution
sorry for my bad Englis
thank you in advance
Try This!!!
schnieder said:
here is my problem
stuck in bootloader.
I have a HTC Athena x7500
Wend I turn on the device, it goes directly to bootloader and
the screen is:
ATHE 100
IPL - v1.00
ATHE 100
SPL-v3.05.0000 OR my old spl is 1.10
I have tried to change the language of my athena and then he died :spanish > fransh
USB (wend is to connect)
series (wend is unconnectable).
I can not turn the unit off by pressing the button, but must take
the battery.
I have tried with hardspl its not working
I want a solution in the forum xda-develop it says my q must upgrade to the rom of espana oficial
After downloading the rom:Advantage_HTC_SPA_2.21.412.1_1.50.00.00_Ship
I tried to upgrade to this rom May j has a mesage on my athena screen:
found spl v1.10
dowload Spl before v3.05 is not allowed! or on my pc has a mesage error 244 invalid model id
I tried to update it with the sd card i have the same mesage
upgrade with athenaUnlucker not work
upgrade with hardspl v7 not work
upgrade with CheetahUnlocker not work
upgrade with athena wraper not work
I tried to fix the problem with mtty
cmd> task 32
level=ff I board on my pda (cid locked)on the Spanish language HTC_304
Cmd> lnb filename.bin 76508000
invalid comand
or Cmd> lnbs filename.bin 75108000
Cmd>
no response
helpe me plaise::crying:
it's been two year since I looked for a solution
sorry for my bad Englis
thank you in advance
Click to expand...
Click to collapse
try this,
here's an experimental program I made to make the process more automatic so users can fix their own wifi without our help.
this is good for both corrupt modelid and corrupt wifi, and fixes both at the same time.
STEP BY STEP:
1. download attachment at the end of the post for mac1.exe (requires .net 2.0 installed on the PC)
2. you will also need to download the other attachment in this post for the mtty program.
3. enter bootloader (tricolour screen) manually by pressing and holding camera button all the way in (yes I mean that, press it in as hard as you can!!), while doing a reset, then keep the camera button held until you see the tricolour screen.
4. disable USB in activesync (wmdc if you have vista - in this case, do not kill wmdc, just disable usb in it!!!)
5. run mtty and select USB option from the dropdown box!
6. then press enter in main window that comes up, see if that gives you Cmd>
7. now you should have Cmd>, if not, re-check if you did the above steps right until you get Cmd>
8. now run the mac1.exe, type in your MAC address you want to use for the Athena, if you have SPL 3.xx reported on the tricolour screen, then use the button for SPL 3.xx, otherwise if you have SPL 1.xx reported, use button for 1.xx.
9. this should have generated a .bin file for you, copy that bin file in the folder of mtty.
10. now, in mtty, type (do not copypaste!) this command: task 32
11. this should return Level = 0
12. now, you must only do one of the two following commands:
- if you have SPL 3.xx, then type (do not copypaste!!) this command: lnb filename.bin 76508000
(there filename is the name of the .bin file you generated - don't forget to put .bin after filename, as the full name is needed).
- OR, if you have SPL 1.xx, then the command is different (do not copypaste!!): lnbs filename.bin 75108000
(there filename is the name of the .bin file you generated - don't forget to put .bin after filename, as the full name is needed).
NOTE, the command starts with a lowercase "L", not "I"!
WARNING: PLEASE DO NOT MIX UP THESE TWO DIFFERENT COMMANDS!!!
if this info helps: most people will have SPL 3.xx, and if you have AP4 (not vanilla) already running then you're definitely 3.xx
13. mtty will popup a window asking "OK", you press OK!
if you get "Fail to synchronize with the host (1)", then make sure you did follow step by step. if still same error, try placing mtty and the bin file under C:\.
14. now the file downloads, if mtty reports it flashed the file, and at the end "code entrypoint unknown", then that's it, now boot back to WM and see if wifi works.
thank you for the answer
I tried with mtty and mac1.zip
here are the step
Cmd> task32
level=ff I board on my pda (cid locked)on the Spanish language HTC_304
Cmd> lnb filename.bin 76508000
invalid comand
or Cmd> lnbs filename.bin 75108000
Cmd>
no response
I do not have the mac address of my wifi on the label of my pda so I put j 11 11 11 11 11 11 is what it must have the real mac address
I do not know what to do
It's been 4 months I'm looking for a solution for my pda
help me please