After having installed the latest wm6 from the update. followed by hard rest I got to screen alignment and it seems to keep asking align screen which I have done over 20 times and I can not get out of it even with new hard set.
Any sugestings or help please.
I forgot to mention the center point is some times not responding.
Thank you
I had the same problem, but found that if you can remove the HTC Album then you can align like normal.
I have the same problem on a wizard.
After a while I realized that there must be something wrong with the hardware.
Whenever I turn the screen on, it opens the Message pane, or whatever is configures on the right top hard button. Then if I turn it off and on, it moves to Outlook . Next time to MMS, etc.
Then, when I press the center button, it opens the align screen, but after I finish aligning, it works fine for a while.
I tried Flashing it many times, with differnt rooms, even the offial ones, and it didn't solve the problem. I also tried dismounting it all, talking all the parts apart and nothing.
Anyboday has any clue about this?
make an oem that auto aligns the screen in personal oemizer. See if that works. So that on the initial boot from hard reset it skips that screen.
I did it on mine and it worked fine but I also never had a problem aligning the screen with the kitchen either.
Related
Just got a s/h exec and I think it is faulty. Whats happens is it starts up ok and works for a while and then for no reason that I can think of it goes into a loop which stops it from working.
When I say a loop I'm not sure thats the right terminology but imagine if you tapped the start button and the start menu opens... and then imagine you tapped the tab button , the next item would highlight. If you tapped the tab button again the next item would highlight and so on. Well its as if the tab button is being hit over and over because all the items in the start menu will be highlighted one after the other over and over again.... it just goes round and round in a loop.
Its possible to escape from this and go to another screen but the same looping will go on in that screen too.
If you switch off and leave for a while and come back to it it works ok for a short time and thens starts the carry on again.
Sometimes if you just wait a while it stops, but will start doing it again even if you dont touch anything.
I've noticed one way to force it to stop is to slide the volume button... this seems to stop the loop and allows normal function for a while.... then the crazy looping starts again.
Has anyone seen this or know anything about it.
Nope sorry, maybe you can have it replaced where you bought it as from your post, you can recreate the problem easily.
Side Note : Have you tried Hard Resetting? Or installing another ROM?
I have tried hard resets and factory reset... problem remains.
Will try new ROM.... just trying to figure out how to do it !
weegee said:
I have tried hard resets and factory reset... problem remains.
Will try new ROM.... just trying to figure out how to do it !
Click to expand...
Click to collapse
Just download a new ROM form imate or something, unpack all the files in the ROM update to a directory, put the attached file in same directory.
Enter bootloader mode (Backlight + Power + Reset Hole) you will see SERAIL on the screen but not backlight so look hard.
Plug into PC, the SERIAL will change to USB
Run the attached file. You will see a photo of an S100 but continue anyway....
Hard reset when finished... DOne
ok have installed latest rom... but exec still doing loop loop
Just for arguments sake, can you try installing Imate's newest ROM?
yea thats the one i have just put on.
It seems to be doing the problem less than before. I notice that it does stop if i press the backlight key or move the sound slider.
I'm wondering if there is dust or dirt got in behind the buttons or something like that... although I would have thought other people would have come across this b4 if that was the problem. The machine is one of the first to come out, although I just got it a couple of days ago.
weegee said:
yea thats the one i have just put on.
It seems to be doing the problem less than before. I notice that it does stop if i press the backlight key or move the sound slider.
I'm wondering if there is dust or dirt got in behind the buttons or something like that... although I would have thought other people would have come across this b4 if that was the problem. The machine is one of the first to come out, although I just got it a couple of days ago.
Click to expand...
Click to collapse
If you have tried different ROM flavors and still get the same problem, then it is definitely hardware related. Send your unit in and demand for a new one not a repair
Just been playing around with it again and notice that I can make the problem happen if i press any of the keys on the navigation pad except the top one.... and i can stop the loop by pressing the light button.
Weird or what.
My initial thought on this is maybe its got wet at some point
I have opened the xda up and stripped it down to all its parts. No sign of any dampness or dust dirt etc. Dont see anything missing or broken.
Put back together, but still doing this.
Driving me nuts.... its a great machine but is very tiresom to use with this going on.
Another think I notice about this machine, I have never used it as a phone, but I tried putting a sim card in and There is no sound through the earpiece. Only sound comes from the speakers when you set it to speaker phone.
I suggest just return it and have it replaced. It's probably a faulty button. Probably gets stuck whenever you press it.
Doesnt need a button to be pressed for it to start.. just starts by itself... and can stop by itself too.
Sometimes it can for ages without doing it, other times it does it all the time.
Cant figure if its hardware or software problem
GHOST-IN-THE-MACHINE
Yea... maybe I should get a priest !
I had this problem when i first got mine, if you move the sound slider down, then up, it seems to stop doing it for a while, and it hasn't happened in the last couple of weeks atall, maybe its because its new, and just needs to settle in?
Jay
Well at least I'm not the only one to have it.
My sound slider does stop it happening but only for a while and then it starts up again.
The machine is perfect in every other way, its just an annoyance I could do without.
I've tried everything, even stripped it down and left parts out, like buttons, to see if they are the source, but no difference.
I have the same problem!!!!!!!!!
Someone help please!!!!!!!!!!!!!!!!!!!!!!!
I have same problem. I send to service but until today they can't repair that problem.
I am quoting a fellow user's problem which happened to me as stated. I had to send my unit into the service center which they claimed that they had to reloaded everything but resulting the sytem to hang after that, and had to replace a brand new motherboard: Can someone enlightent me why did it happen and how to prevent such things from happening again.
I am encountered a problem with my D810.
I was loading a Sudoku game and after that my touch screen stopped responding, and the TODAY pull-down menu kept flashing on and off. But all the buttons working fine.
Tried to realign screen, but problem kept recurring, even after removing the new programs installed.
Soft reset many times, yet to do hard reset.
When connected to PC, the connection only established for a short while and dropped off after a while!
Now things got worse, my PC now can't recognise my D810 at all.
Could some one please help out here?
Thank you.
Not sure about the PC but sometimes a screen protector can get between the case and screen and it can put pressure near the start menu. Also, the actual phone case can do this on rare occasions. Check for clearance with paper. Hope that helps.
My Wizard is brand new first off and I haven't done anything to it but install the t-mobile cabs, a spb program, and a few other random things.
Problem (It just started doing this): I can align the screen and it will stay right and aligned for a few minutes but then when i write on it the alignment will eventually veer off on the right side just a little bit. When I pick it up at first normally it writes fine and then it starts acting crazy, sometimes it will write somewhere completely different than where the pen is on the screen, or when I go to press a button it will press the one under or over (mis-aligned). I can even write on the screen and the cursor will go completely crazy and all over the place when I'm trying to draw a straight line. I searched for firmware updates and topics on the issue and didn't find anything.
Any help is appreciated,
Thanks
I had a iPAQ that started doing this after a few weeks. I had to send it in for a replacement. Call T-Mobile about it.
My 8125 (wizard) does this every once in a while. If I let it sit for about a minute then it seems fine. I think it is pbar program that is doing it. Just haven't removed it yet to find out.
You might want to do a hard reset to bring it back to the way it was when you got it and use it for a few days to see if that does it.
Yeah I have actually read up on the topic now and it's a known issue.
It's mostly a hardware issue, so I've narrowed it down to the screen being a little bent. Just a tad.
When you take your finger and rub it over where it's bent or just across the screen in general sometimes it fixes this error. That's about the best fix i've found yet that actually works.
This is driving me nuts too
Hi!
I have a Cingular 8125. Bought it in Nov 2006.
I have been facing a problem with the alignment as well since the past week.
1) Whenever I try to tap the target, nothing happens. I have to do a soft reset to start using the phone again.
2) Have hard reset the phone twice in the past week, but the problem still persists.
3) If I am adding a new contact, wherever I press an alphabet, the 4th or 5th key to the left of what I press gets displayed.
If anyone can help, I would really appreciate it.
Thanks.
Fix Screen alignment
Hi,
It happens to my 8125 each time I turn it on. The only way that I could solve the problem is disassembling the unit and remove the front cover. Clean the borders of the touch screen and remove any particle. It solved the problem.
Hi there,
I'm having an issue with my touch HD. I came to use my phone which was stored fine in my room not touched, I came to use it and it wasn't doing anything I pressed. So I decided to restart it and then when I tried to enter my lock code it wasn't noticing what I pressed and was pressing other numbers leading me to believe that it is a screen alignment issue.
However I managed to get on the screen align thing, but everytime I pressed the crosses, it would restart the sequence again and ask me to do it all again. I can't use the phone because I can't even get past the lock code.
Any suggestions? tried searching the forum but couldn't find anything..
Thanks in advance
Seanyy said:
However I managed to get on the screen align thing, but everytime I pressed the crosses, it would restart the sequence again and ask me to do it all again. I can't use the phone because I can't even get past the lock code.
Click to expand...
Click to collapse
Perhaps not of much use but I have had to "click on the crosses" in Align Screen up to 5 times after a ROM flash or similar so I would do it a healthy number of times.
If it is stuck in a long loop, I am stuck for suggestions.
That happens to me when I don't use the stylus for calibrating.
You have to be fast and press it firmly.
Thanks for the suggestions both of you, but still no luck
I have a Sprint Touch [Vogue]. It has served me very well up until recently.
One day, I was using my phone normally when the battery died. No big deal right?
Well, I charge my phone and reboot it. For some reason, Windows is EXTREMELY slow and unresponsive. I figure that something vital had been corrupted by the battery's death, and that it was nothing that a hard reset couldn't fix.
I performed a hard reset.
I let the utilities for the first boot run to customize the phone. Everything seemed pretty much normal. I configured my settings, re-added my contacts, etc. Then I turned the screen off [with the power button].
I turn it back on later to do something. I touch the screen. It immediately and accurately detects the touch's location, but it continues detecting a touch. For 20-30 seconds, after the input has stopped.
It was strange, so I soft reset the device. It booted, with the same problem. So I performed another hard reset. I did some configuration [the response acting normal at this point], and then turned the screen off. Turning it back on brought the same problem back.
This problem still exists on my phone, even after numerous hard resets and even ROM flashes.
A better description of the problem: When the device is first turned back on [meaning brought out of standby], its touch response is messed up. It will immediately and accurately detect any touch input, but it will continue to detect the input for up to 30 seconds AFTER it has been released, as if you were holding it the whole time.
WHY is this???? My phone is almost unusable because of this!!!! I can still place/ receive calls, using the navigation buttons and the red and green buttons. But the touch response is screwed!
Can someone please shed some light on this problem I'm having?
Phone specs: Windows Mobile 6.1, HTC / Sprint customized. Minimal third party software is currently installed.
[I've already determined that third party software is not the problem, because i haven't installed any!]
Possible solution
Hi,
today I experienced something similar to your description - no touch response when I tried to pickup a call. The strange thing is that last night everything was working and no settings were modified nor programs were added/removed. The screen suddenly 'died'. At the moment I am using it through a program MyMobiler which brings the mobile display to the PC and I can use the mouse to control the phone (it is like VNC for the phone screen, the phone is connected with ActiveSync).
This is temporary solution untill I finish my backups of files, programs, settings. I didnot performed hard reset yet, hope this will solve my problem
In the following link there is a 'magical' solution - to remove the screen protector:
http://www.htcwiki.com/thread/1112981/LCD+or+Touch+screen+not+working
P.S. I had removed the screen protector and voilá - the screen is now touch responsive. The root cause of the problem obviously is the dust between the screen and the protector which results in constant screen pressing - and as a result no accepting my finger presses.
I hope this will work for you and others with similar problem.
I had a similar experience with an old Vogue.....In my case, there was no battery death precursor, but it just started acting up. Not too long thereafter, I noticed the screen/digitizer was forming what looked like an air bubble between the digitizer and the LCD on one place of the screen. The screen was becoming defective. I eventually had to buy another Vogue from a friend who didn't have a clue of the 6900's potential, and didn't want his anymore, so I got it cheap.
Sounds like your screen/digitizer may be on it's last leg.