8525 tricolor.. clueless?!!? - 8525, TyTN, MDA Vario II, JasJam General

Okay, soo my friend gave me his old 8525.
I started to use it, it worked fine for about a week,
until i started to notice how the QWERTY keyboard was
becoming unresponsive at times.
I didnt think much of it, until a reboot
and my screen went tricolor
with the words
HERM100
IPL-1.01
HERM100
SPL-1.06
and below in the white
Serial
EMAIL ME
[email protected]
if you can help in any way, im tempted to trash this phone
I honestly have no ideaaa what in the world this means, but obviously its not good, i tried the soft and hard reset, but yeahh nothing.
CAN ANYONE HELP ME!!!
and Im serious, when i say i know nothing about this phone
I switched from a Blackberry Pearl to the 8525.

I can tell you that what you're seeing is the boot loader, from here you can hard reset the device to try and get it back.
I had this happen once before on my jasjam.

Plug in the USB and Launch the ROM installer (http://www.america.htc.com/support/8525/software-downloads.html for offical)
has gotten me out of being stuck in the boot loader plenty. That or try loading an memorycard with a rom image named HERMIMG.rbh (http://wiki.xda-developers.com/index.php?pagename=Hermes_SDCardFlashing)

Mmmm,
I would be very careful. As ruxton said you are in bootloader mode. As you do not know anything about this phone lets be a bit more specific. (I hope its well your phone )
The bootloader mode is there to load (flash) a new firmware (Can be the OS, a radio rom, etc...) As we speak about the kernel of your pda, there is obviously a risk to distroy it. This is why it is hardly recommended to install another SPL (hardspl from olipro) before playing. But this is another story... for the moment.
IF the firmware is not corrupted, you can leave the bootloader mode:
Try first to "soft reset" your pda (little hole on the bottom of the phone. Push the button with the stylus). It will reinitialise the pda without loosing data
Second: Remove the battery for 1 minute and insert it again. Soft reset if necessary
Third: the hard reset method. Here you loose your data: Push "soft key left" (above the ms logo), "soft key right" (above the ok) maintain together and perform a soft reset at the same time (see above). Answer to the questions.
If this does not work, this could mean that the firmware is corrupted. You will have to flash... But again...this is another story. Lets see if it is necessary.

Still lost on trying to fix this thing guys.
Sorryy i told you i was new at all this.
Can anyone help me try and flash it with my SDcard?

all the info you need to unbrick your phone is here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
if you want to flash via sd card:
http://wiki.xda-developers.com/index.php?pagename=Hermes_SDCardFlashing

Related

help needed on restoring/reinstalling my tmobile mda compact

please help i have the t-mobile mda compact pm200 and i was removing a cracked version on pocket dos v1.09 from the remove list and it said windows wil need to perform a soft rest yes or cancel i clicked yes and my system restarted but now it just get stuck at the t-mobile screen. i have tried doing the manufatures hard reset but no joy i have take out the battery no joy and i can't even access it through my p.c what can i do to get it up and running again i don't care about the data already on there cuz it is all backed up on my sd cad
When you took out your battery, have you been waiting til the backup battery fully drained out? It takes about 30-60 minutes, better leave a few hours. Try this and post your results...
thank for trying but unfrtunatly it had no effect i tried for two hours then reinserrted it and no joy so i waited a further day but still nothing any other ideas tnx
Is it getting into BootLoader? Then you might try Flashing a new ROM!
how would i go about doing that? my computer won't even recognis3e my phone
I had about the same problem:
I was trying to install the Pocket PC Greek language support (free trial version) from the site http://greek.pocket-pc.penreader.co...der_Greek.html. on my MDA Vario Tmobile when it crashed!! It shows just a white screen and does nothing at all!! I soft and hard reseted the device but after restarting it shows the Tmobile screen and after a few seconds a white screen! Actually I am not so sure that the device is hard reseting because it doesn't ask me for a confirmation of the hard reset. When I startup my device it stops on the same white screen.No windows loading, no other commands accepting, not recognized by my desktop.
Did anybody have the same problem before? Does anybody know how can i get my PPC on working condition again
Thanks dagonist.
I hope somebody can help....
See for ROM upgrades on the forum :wink: if u get some images on the mini then it's not dead! It's just stuck at the bootloader mode, meaning that the OS is somehow damaged.. To solve this prob u must plug the mini into the pc (it will be recognised as an unidentified device, don't worry), then download a ROM upgrade set (u will find these on the net or in the xda-dev ftp). Execute the prog, wait 'till it finished and voila! Ur device will come as new If u encounter problem do a simple search in the forum regards rom - bootloader - upgrade and u willl find a lot of infos :wink:
Hope this helps, MocciJ
Thanks MocciJ.....but my desktop pc doesnot "see" my pocket pc at all!!
:? then it isn't yet in bootloader, is just stuck at the beginning of a broken OS! I mean that it tries to load the OS, but then it gets stopped since he read bad ROM (probably deleted in some way since u encountered this prob removing a prog) try to get it in bootloader mode, by pressing together the camera, power and reset buttons.. U will lose all the things in the RAM memory, but in this case u really can't do anything else.. After entering in bootloader, u can easily upgrade it..
MocciJ
Well, I just tried the camera button+power button+reset button....and nothing happens! It reset and comes back to the same white screen...
Any other suggestions??
well, did u tried to make it correctly? I mean: for entering boot loader u havce to press camera + power, and then reset (with camera and power pressed) if u can't still enter the bootloader, then I'm out of ideas, sorry...
MocciJ
I amdoing it write but nothing happens....
In the screen what can u read? If u read serial (it is barely visible) then see if it turn to usb when u connect the cable: if yes, we 're at a very good point...
When it starts up it shows the Tmobile logo and then for a few seconds :
ipl 1.08
spl 1.08
gsm 01.09.10
(something else...)
after a few seconds a white screen without any letters or anything else.
But I cannot see it anywhere on my desktop pc...
:? I can't figure out how you can get it back.. If it displays images and text, then the bootloader is still alive.. It even tells u the correct version of the complete ROM.. but I wonder why it can't access to the bootloader.. u must search in the forum how to reach the bootloader, but I'm sure of the power camera reset combination; when u can read SERIAL or even better USB on the device, u probably have solved most of ur problems, but chances are that u have even bad clusters of ROM, and cannot be restored with an upgrade (it happened to the External Rom of my mini after a bad upgrade)
I suggest to send it to repairs, before doing somewhat wrong, because if there is an original ROM inside they will repair it for sure, free :wink:
MocciJ
Thanks. The problem is that I got the phone from ebay, from a UK seller, and it was locked to Tmobile. So I don't think that I can ask for a factory/guaranty repair....
Thanks. The problem is that I got the phone from ebay, from a UK seller, and it was locked to Tmobile. So I don't think that I can ask for a factory/warranty repair....
seee i tried all of thoose things but i found the main problem was getting the computer to recoginise the thing and the program i put on was a cracked version ( i know i am a naughty boy) so if i send it off they could cause legal problems couldn't it
it depends on what u are meaning by "not recognised" but I assume that windows dosesn't even try to recognise the device (I mean that there aren't bubbles, notifications, or any other changes on the system) for the cracked software, well if u have installed it right into any RAM folder (not in the storage memory) then u can tell the repairing center that ur unit simply doesn't power on correctly.. :wink:
MocciJ

Cincular 8525 stuck in Bootloader

I have a Cingular 8525 running WM5 that is stuck in bootloader screen. I have tried to soft and hard reset ... just boots back to the same screen, I can't turn it off once in the screen and when i sync via usb to the pc i get the message that the "usb device that is connected is malfunctioning" I have not done any upgrading at all and the phone worked perfectly right up till the time i powered it down and restarted into the bootloader screen.
Please can someone out there help me with this issue?
Zulu137 said:
I have a Cingular 8525 running WM5 that is stuck in bootloader screen. I have tried to soft and hard reset ... just boots back to the same screen, I can't turn it off once in the screen and when i sync via usb to the pc i get the message that the "usb device that is connected is malfunctioning" I have not done any upgrading at all and the phone worked perfectly right up till the time i powered it down and restarted into the bootloader screen.
Please can someone out there help me with this issue?
Click to expand...
Click to collapse
same problems, run perfect before with schaps wm6 rom then flash to faria wm6.1... not feel good with faria. try to flash with other rom then the problem start ..
how to recover ....... please help
Asfarizal said:
same problems, run perfect before with schaps wm6 rom then flash to faria wm6.1... not feel good with faria. try to flash with other rom then the problem start ..
how to recover ....... please help
Click to expand...
Click to collapse
Manage to solve the problem ...thanks WIKI !!
Go to Bootloader mode: Hold side OK and POWER buttons together and reset with stylus
Then Flash to any ROM you want !!
Thanks .... But
Thanks for the reply ... but i have no idea how to do what you tell me, I am new to all this phone "stuff" as a matter of fact this is the first time that i am ever using one of these forums. I have read till i am cross eyed but dont actually understand what you are talking about ... now don't let that scare you away as i am willing to learn and i am not braindead ... you all had to start sometime in this, not so. I get that i need to try and reflash my rom...
so is there some type of rom update software that i need? ... what is a hard SPL?? ... and who is Schaps?? .. sorry guys to do this to you but i would like to get into this game and i need some ( well maybe a lot ) of pointers.
Thanks for your time.
1. Search for "mr vanxs guide" so you have an idea on what you're doing.
2. OK, as Asfarizal said "Go to Bootloader mode: Hold side OK and POWER buttons together and reset with stylus". If you cant work out what the buttons are, go to the manual. it will tell you.
3. type in "hard SPL" in search on the forum & download the .zip or .rar file. this should have 2 files inside when opened,
a). RUUWrapper.exe and
b). RUU_signed.nbh
sync Hermes and double click .exe file. follow prompts.
4. find a rom that you want (would suggest TNT SE as a fairly good rom for noobs... good and stable, no problems...) Again download, then (and this is personel preference) format an sd card fat 32 and copy RUU_signed.nbh into root directory. Rename it Hermimg.nbh. Put into Phone and put into bootloader(make sure the battery is more than 50%) follow prompts. This should get you out of trouble. You can also sync your Phone and double click on the RUUWrapper.exe HOWEVER, if you should reset your computer, pull out the usb cable or have anything else happen to the computer that interrupts the flashm, you could end up with a worse brick than you have now. try to read up on flashing (search for "mr vanxs guide") and this should help you a lot if you have other questions. Good luck and happy flashing......
Thank You
I will follow the instructions you gave and try to get it going this weekend.
Thank you so much for your time
Zulu137 said:
Thanks for the reply ... but i have no idea how to do what you tell me, I am new to all this phone "stuff" as a matter of fact this is the first time that i am ever using one of these forums. I have read till i am cross eyed but dont actually understand what you are talking about ... now don't let that scare you away as i am willing to learn and i am not braindead ... you all had to start sometime in this, not so. I get that i need to try and reflash my rom...
so is there some type of rom update software that i need? ... what is a hard SPL?? ... and who is Schaps?? .. sorry guys to do this to you but i would like to get into this game and i need some ( well maybe a lot ) of pointers.
Thanks for your time.
Click to expand...
Click to collapse
Looks like you've got a lot of reading to do, and a problem to sort out. Firstly a couple of answers...
Schaps is a Rom Cooking guru (makes custom versions of WM5, WM6 etc). When you get your phone sorted out I'd recommend trying one of his roms.
Hard SPL. The SPL is part of the bootloader which effectively dictates how a rom is flashed and what roms can be flashed. HardSPL is a custom version of this which allows you to flash any rom from any carrier. It also protects against a bad flash in many cases. It is recommended before you try flashing any new roms or radio roms. Use Hard-SPL-V7 at the bottom of the first post here.
The Rom upgrading software is contained in any of the cooked or carrier supplied roms. It is normally a .zip file which cotains 2 files: xxxxxRUU.exe and RUU_signed.nbh. You run the .exe file from your PC when connected to your phone via USB. More details of how to do this are in MrVanx's guides. Also other resources here.
Now to try to sort your phone out...
What is displayed on your screen when in bootloader mode? It should be something like this:
HERM200
IPL-1.04
HERM200
SPL-2.10.Olipro (This is HardSPL V7)
If you don't have an Olipro SPL then you need to get HardSPL onto your phone. If you haven't done any upgrading and have had the phone from new then I guess you don't have hardSPL.
Now you need to fix your USB Malfunctioning problem. I can't help too much here except to suggest trying a different cable, different USB port or different PC. Also, if you are running Vista try an XP maxhine. When you connect to the PC does your phone show Serial or USB on the screen? If you can't get a USB connection, all is not lost - you can re-flash your rom using an SD card, method here.
There is a thread about un-bricking phones which may help.
There are various diagnostic tools (which can also screw your phone if used incorrectly). The favourite of these is MTTY but you need a USB connection to use this.
If your phone is in warranty I'd recommend getting your supplier to sort it out, but if not I'd try to re-flash an ORIGINAL supplier rom (Cingular I guess). You can get links to the official supplier roms here.
I think (might be wrong) that sometimes when stuck in bootloader you need to flash an official rom, not a cooked one to recover your phone - then you can run HardSPL and then flash cooked roms again.
Cingular 8525 stuck in bootloader
Thanks for the reply ... lots of great input.
Now to answer some of your questions.
1) When I power up the phone (only pushing the power button ) it goes straight into the bootloader screen without pushing any other buttons, and it displays
HERM100
IPL-1.01
HERM100
SPL-1.06
Then at the bottom in the white bar it says "Serial"
The only way that i have found to power it down again is to remove the battery, there is no response from any single buttons after it is in bootloader
the soft reset and hard reset work but it just goes right back to the bootloader screen after.
2) The USB malfunction. This only started after the phone "crashed" and before that it worked great ... well i only used it to sync up to my work pc for the contacts and to get pictures onto my hard drive.
all the PC's that i use are running XP. I have tried my home PC and my Laptop
and the work PC and all of them have their own cables and they all say the same thing ... "the USB device is malfunctioning"
I am sure that when i get the phone going again the USB will start to function again.
3) Phone warranty ... I bought the phone off e-bay from a store in new york about 10 months ago as a "new unlocked cingular 8525" it was new and unlocked, but i have no idea how they unlocked it. I would assume that there would be no warranty now and in any case i live in Canada and would have to ship it down to the states to an AT&T repair center and that sounds like a nightmare to me with the customs and so on.
I will give you a little more background on the problem. the phone worked like a charm without any problems at all for the 10 months that i had it, then the morning of the crash the phones alarm did not go off in the morning and i was almost late for work ... i did not pay it any further attention untill at 3:26pm
that afternoon the alarm went off ??????? (it was set for 6:05am) so i checked the main clock time, it was right. I then checked the alarm time, it was right ??? So i figured that something must have just got confused, so i powered down the phone with the power button to just restart it and while it was powered down i removed the battery to take the oportunity to to clean all those fuzzies and dust that collect in the battery compartment out and put it all together and powered it up again (just by pushing the power button) and this wierd red, green, blue and white screen appeared and that is all that i have seen since ???
I hope that answers your questions and i will start going through the links that you sent and get to reading ... will there be a pop quiz ... lol
Thanks again for your time and i very much appreciate all the time that all of you have spent on me and my phone ..... I know that you all just feel bad for me because i now have to use a Motorolla V551 ... lol
Great Work
ultramag69 said:
1. Search for "mr vanxs guide" so you have an idea on what you're doing.
2. OK, as Asfarizal said "Go to Bootloader mode: Hold side OK and POWER buttons together and reset with stylus". If you cant work out what the buttons are, go to the manual. it will tell you.
3. type in "hard SPL" in search on the forum & download the .zip or .rar file. this should have 2 files inside when opened,
a). RUUWrapper.exe and
b). RUU_signed.nbh
sync Hermes and double click .exe file. follow prompts.
4. find a rom that you want (would suggest TNT SE as a fairly good rom for noobs... good and stable, no problems...) Again download, then (and this is personel preference) format an sd card fat 32 and copy RUU_signed.nbh into root directory. Rename it Hermimg.nbh. Put into Phone and put into bootloader(make sure the battery is more than 50%) follow prompts. This should get you out of trouble. You can also sync your Phone and double click on the RUUWrapper.exe HOWEVER, if you should reset your computer, pull out the usb cable or have anything else happen to the computer that interrupts the flashm, you could end up with a worse brick than you have now. try to read up on flashing (search for "mr vanxs guide") and this should help you a lot if you have other questions. Good luck and happy flashing......
Click to expand...
Click to collapse
Thanks a lot man & great work i unbricked my Herm100 with method u mention above thanks a lot & great job keep it up
I also have this problem.
I d/l Hard-SPL-V7
and when i run RUUWrapper.exe
I get an error saying the application failed to initialize properly (0xc0000135)
What's going on?
How do i fix this?
this happened when i was trying to unlock the phone.
Thanks
need help
when i switch on my orange herm100 it shows On the bootloader screen is displayed:
HERM100
I PL-1.01
HERM100
SPL-1.40.01ipro
history : i buy unlocked orange phone
fewdays back i found no imei ,
yesterday i try to flash by micro sd but in gsm stage its gets hang no progress after extrom stage
IPL - OK
BOOTLOADER - OK
SPLASH1 - OK
SPLASH2 - OK
EXTROM - OK
GSM - (NO ACTION)
OS -
i tryed several time no action, i cant connect by mini usb.
PLEASE help me
tell me which it the right rom to chose? step by step procedure..
how to rectify imei?
thanks and regards
kirtibas
kirtibas, sorry it took so long to reply, 1st thing I'd do is upgrade to SPL 2.10 olipro. This is safer to use than others. then I'd suggest reflashing a stock rom to see if that works. After stock rom works then use a cooked rom as your heart desires... Cheers...

Dead/Dying phone? Need help asap :(

I don't know if the phone is bricked or what. Was in the store tonight, tried to text message my wife who I couldn't find and the phone was all locked up.
Soft reset, and only the date/time loaded, nothing would run. Soft reset again, and the phone didn't load past the bright splash screen. Tried soft reseting a bunch more times, nada. Did a hard reset, first one didn't work. I think it was the 3rd hard reset that took. Phone seemed like it was back to basic WM5, would be okay. Went home, put it on the charger.
Went to take it off the charger to reload data, and it won't turn on. Soft reset, freezes at bright splash screen. Hard reset, same thing.
Is my phone bricked? Anything that I can do to revive it? Or am I SOL?
Cingy/ATT 8525 w/WM5
(By "bright splash screen" I mean when the splash screen flashes brightly. It increases brightness, but just stays that way.)
Any help greatly appreciated.
I managed to load the official WM6 ROM (spl 2.03) via the built-in bootloader. I have radio, ROM, and GSM. It boots through the ATT animation, then freezes. It leaves a black screen with a blue and green static bar running horizontally across the screen about 1/4" thick.
I don't know how to get Hard-SPL loaded on the device because the only way I can see the device is when it's in the built-in bootloader mode.
will attempt PB/KITL I guess, though I can't at this point get the phone to display the KITL info.
No KITL in the ATT WM6 ROM.
Managed to get ATT WM6 ROM through the setup, after the "customization (bloatware)" it reset, and now it sticks on the bootup animation.
So close, I have SSPL and Hard SPL on the micro SD, if only I could get to the damn file manager. If I could somehow cancel out the customization process grrr.
On power charger, I seem to be able to get through the setup after a hard reset okay. It just won't boot after the reset.
Any ideas. I gotta get a few hours sleep. Sorry if this dialog to myself is in the wrong area, I didn't notice the "bricked hermes" thread was in the upgrades, etc area.
viatorx said:
No KITL in the ATT WM6 ROM.
Managed to get ATT WM6 ROM through the setup, after the "customization (bloatware)" it reset, and now it sticks on the bootup animation.
So close, I have SSPL and Hard SPL on the micro SD, if only I could get to the damn file manager. If I could somehow cancel out the customization process grrr.
On power charger, I seem to be able to get through the setup after a hard reset okay. It just won't boot after the reset.
Any ideas. I gotta get a few hours sleep. Sorry if this dialog to myself is in the wrong area, I didn't notice the "bricked hermes" thread was in the upgrades, etc area.
Click to expand...
Click to collapse
Not sure I fully grasp what's happening here, but if you want to stop the customisation then hard reset and when it goes to the loading cusimisation stage shove the stylus in the hole to do a soft reset and it will stop it loading.
Mike
Alright, thanks, will give that a try.
I managed to run the official ATT WM6 ROM and flash it without a hiccup (twice), and task 28 in bootloader says no bad blocks. So I am confused how I can flash an "official" ROM successfully and the device still won't work. Am starting to suspect hardware failure apart from memory.
Thanks a million mate, that worked. Phone boots now, already have SSPL installed. Need to update .net and activesync for Hard-SPL 7 to run I guess. Then I have more options.
Woot! I unbricked my phone
Once I was able to hard reset and cancel the "customization" I ran SSPL, then Hard-SPL 7, then I Super-CIDed the device.
I haven't tweaked the data settings yet, but I can send/receive phone calls. Which is a coup, because this is my main line.
It runs sluggishly. I don't know if that is the ROM or the device. It won't boot if it's plugged into USB, and after flashing Hard-SPL it isn't a recognized device by windows, won't connect to activesync.
I am treating the phone gingerly right now, will try and unload the ATT wap settings cab and restore my pim.
At least now I have the option to install another ROM if it bricks on me again.
I really should have flashed Hard-SPL the DAY, the MINUTE after the warranty was up. Lesson learned.
Or not.
ATT ROM locked up on me, decided to try Schaps 4.40. Won't load past WinMo "tap screen to setup" screen. Guess I'll try something else.
For a stable WM6 rom try TNT SE. It is REALLY stable but does come with some 3rd party apps. Thought you might like to get it working though first then try the other roms and in my experiance I haven't found many other roms that were THIS stable...
Hope you get it working...
For a disassembly guide try this site - http://michael-channon.spaces.live.com/PersonalSpace.aspx?_c02_owner=1
Its a bloody good place to go for all things to do with hardware and Mike is a true guru with hardware problems...
Cheers...

Cannot enter bootloader, but not bricked!!

Hi guys:
Really strange thing. When trying to flash phone (activesync connected) the phone went to blank screen and RUU lost conection. After that there is no way to enter bootloader, but everything else is working ok.
Device has USPL installed, and been flashed many times.
Is there any way to repair bootloader?
Thanks.
Note: Actual ROM is official HTC WM6, with ext ROM modified to 2 Mb capacity.
how are you entering the boot loader
To enter the boot loader you have to either keep the voice record button held while doing a soft reset or keep the same button pressed while the device is starting
Yes, I Know
kganesh1234 said:
To enter the boot loader you have to either keep the voice record button held while doing a soft reset or keep the same button pressed while the device is starting
Click to expand...
Click to collapse
Thank you for your apreciation, but I have already done it.
I've been browsing this useful forum in order to learn a bit more about my artemis
hmmpp
RUU hehehe..
Take the SD card out then perform the procedures to get into the Boot Loader, it will work, otherwise you'll see white screen for 2-3 mins then the phone will say "Searching for SD Card..." then it will eventually get into the bootloader, if this solves your problem then please try the search feature next time because this has been discussed many times before...
digitalextremes:
Please go..... with "search button" text.
Everytime i see such text i wonder if U ever tried it!
nevertheless.
My Arte has the same problem, OS is launching properly, everything seems ok.
I want to flash a new ROM (Shady's last PLK) but i can't get into bootloader.
Thank U in advance for post with Voice-dial+Power+reset (stylus) or mentioning sim or SD, i tried all combinations.
If U have nothing to say, stay silent.
Everyone who can help, feel free, to do so.
THX I A
I had the same problem... to fix-it, just remove the SD Card...

i reeallyyyy need somebody's help with unbricking my phone.. please hellpppp!!

alright.. i made a similar post to this before and i came across the wiki...
well i can't view what my SPL or my IPL because as soon as i turn the device on, all that shows is the boot loader screen and displays serial on the top with 0.16-0.90 in red characters on the bottom (I'm not sure what those are)...
here are the only details that i know about my phone:
I DON'T have hard SPL
My Original ROM i was using before was an htc windows mobile 5 rom
The reason that my phone is bricked right now is because the usb cable disconnected in the middle of the flash
I'm using Windows Vista for flashing
Computer won't recognize the phone when on usb
My phone (qtek 9600) can't load the operating system
*EDIT*
THE PHONE IS STUCK ON BOOTLOADER WHEN I TURN IT ON, NOTHING ELSE, BUT THE BOOTLOADER SCRREN DOESN'T SHOW MY SPL AT ALL.
ALSO, MY COMPUTER DOESN'T RECOGNIZE THE PHONE....... MY PHONE HAS A TYPE 2A BRICK
Helping me will be greatly appreciated
come on.. I'm without a phone
Do you have a 2GB or smaller SD card? Copy a rom image to it and rename it HERMIMG.NBH
Turn it on and you might get lucky!
Just make sure its stock rom that was supplied, or the updated WM06 version as the CID should check out then...
vwkess forgot to mention, reset into bootloader, hold power, ok button and reset with stylus. Hold all buttons in until you get to the tri-colour screen. If it works, follow the prompts....
Cheers...
hi,
i think i can hlep.
i had recently bricked my phone with a custom wm6 image, it worked fine for two days and then i reboot, and all i see was the welcome image, nothing else.
so what i did is -
i pressed the hard reset buttons - power + OK + SOFT RESET (Stylus), kept it pressed for 3-4 seconds, the fone rebooted, the screen was full with some colored bricks i connected my fone in USB and on screen i saw USB.
I then again flashed my fone with the working update, it worked perfectly for me, try may be you can get some luck
ps - before doing all these, i turned my fone off by removing the battery, i removed sim card and mmc card as well.
regards
That may work too, but again, try to flash with a stock rom, untick "connect with USB" in activesync and then try.
Make sure you go to boootloader screen, instruction in rajivlodha's post, before you connect to the pc.
Goodluck...
I need some help as well.
I think I may have bricked my phone. It's a rooted htc hero cdma. I'm running cyogenmod on it and it was working fine, until using metamorph to apply some changes to the theme.
I went to reboot, and it now it won't load past the htc screen. Even when i try the key combination to put it into recover mode. I didn't install a nandroid backup, and i'd be fine with just completely wiping my phone. help is appreciated.

Categories

Resources