My device has been working perfectly till suddenly & without any early notice the device has been locked with some kind of locking.
After reset the device goes into the locked status showed in the pictures, no option to do hard reset,
Tried all options, seems like one of the keys is defective and that’s why can’t perform hard reset.
The device is locked and the 90 minutes limit don’t go down, you can’t do anything.
However if there is a incoming call, you see it on the screen and you can answer the call.
Does anyone familiar with this lock screen ? how do i pass it & relase the device? please advise & help me ....
This is the password protection built into all versions of windows CE. (accesed form control panel/personal/security (or something like that, may vary with OS versions). It has options to lock the device after switching it off (going to sleep mode is considered switching off too), or after the device is not used for a given period of time. The whole point of this protection is to prevent unauthorized access to the device, so i think that without the password you're screwed
Did someone play with your phone before that happened? Maybe it was a "joke" by one of your friends? If you never set the password, anyone can enter the password settings applet and enable it. That's why it's always a good idea to set the password, even if you don't plan to use it -it is also required to enter security settings...
So, if you really want to HR, first of all make sure that one of the buttons is really defective - I just checked and you can't turn off the device by holding the power button when it's loched - this might be your problem. So try holding the comm manager and voice command buttons and press reset button on the side (keep the side buttons pressed until you get the "reset to factory defaults" question)
.
If that doesn't work, try checking if the device connects to activesync when it's locked. It shouldn't happen, since it would be a possible security hole, but knowing microsoft...
If it does you might try to flash its ROM (of course you would lose all your data).
And if it does not and one of the buttons really is defective you might have to disassemble the device in order to do a HR (by shorting the switches' contacts with some metal object), but i wouldn't do this if you don't have some experience with electronics, since you might damage the phone if it's not handled properly with case removed. It might be easier to go to a GSM repair shop and have the switch replaced.
itzik-g said:
My device has been working perfectly till suddenly & without any early notice the device has been locked with some kind of locking.
After reset the device goes into the locked status showed in the pictures, no option to do hard reset,
Tried all options, seems like one of the keys is defective and that’s why can’t perform hard reset.
The device is locked and the 90 minutes limit don’t go down, you can’t do anything.
However if there is a incoming call, you see it on the screen and you can answer the call.
Does anyone familiar with this lock screen ? how do i pass it & relase the device? please advise & help me ....
Click to expand...
Click to collapse
Forget all that password bs. Lock your device with this rogram. Unlock by pressing both soft keys at the same time.
Related
Hello,
Wondering if someone can help me, i have a very strange problem indeed!
I've just rest my device and when it came up with the Unlock screen to type in my unlock code (4 digits) I can press the buttons on the screen, and the code is typed in, but when I come to press any of the unlock buttons, they do the physical depress animation but it's as though they are not registering the click event.
This is on Mirri WM6.5 rom.
Any help would be appreciated, I also tried to use MyMobiler to use my mouse to try and do it, but as I last used it as Mass Storage, it won't connect as I can't get to set it as ActiveSync.
*Edit - Further update, if I dial 999, I can correctly press the cancel button, which means it's not that portion of the screen which is obscured, it's just the unlock, contacts, mail buttons that are failing to unlock the device. I receive no error messages when typing incorrect codes either.
Could it be possible a program has changed my password?
Thanks in advance folks.
D.
** HARD RESET DEVICE **
Too business critical to keep messing about, please leave comments if you have any ideas incase this happens in future.
I severely doubt your password has been changed. If you are unable to press unlock, it may be worthwhile performing a hard reset to see if this fixes your problem. Obviously backup contacts, emails etc beforehand as you should still be able to do this.
Hi,
I was unable to do anything with the device, so had to hard reset.
As the device was locked upon startup, the only thing i got was the enter device unlock code screen.
I know the changed password is a strange idea, but can't think of anything else unless my device is actually knackered... just finished hard reset now.
THEAnarch1st said:
Hi,
I was unable to do anything with the device, so had to hard reset.
As the device was locked upon startup, the only thing i got was the enter device unlock code screen.
I know the changed password is a strange idea, but can't think of anything else unless my device is actually knackered... just finished hard reset now.
Click to expand...
Click to collapse
Any joy after hard reset?
All seems to be working perfectly now, have lost a few days of txts since my last backup, but otherwise all up and running... very strange indeed!!
Thanks for checking back
Hello to all,
I have the HTC Ozone from verizon... Recently I flashed the custom Windows Mobile 6.5 Rom onto the device and attempted to install my screen reader without much success. (yes... I have no vision.)
Now, the device boots up, but is frozen at the windows mobile splash screen. I can't seem to find a way to reset the device without it loading Windows mobile completely. When I plug it into my laptop, USB is not recognized.
Does anyone know a key combination I could use to reset the Ozone (at boot)? I used to have a Q but Enter with the end key does not work anymore - and the user manuals only talk of using the "clear storage" option in system tools.
Any help is appreciated.
With all due respect-
Tomi
did u hardSPL ur device?
u gotta start there..sounds like you didnt tho. Theres another member whos in ur shoes at the moment, who himself didnt read the instructions.
yeah... I knew of hard spl, and it ran to 100%. But I guess it didn't install. in the end I had to go to verizon and they replaced the phone - however I will not be flashing another cooked rom until we get a signed stock ozone vzw rom.. Or generic.
I was told on another thread here that holding down the volume down key + send +end will put the device in reset mode, and that's true. However even that didn't help, my rom was prob gone.
-Tomi
You can do a Clear Storage from bootloader by turning off the device. While holding volume DOWN key and SEND key, power on the device. Follow the prompts.
If that doesn't do it, it's bricked.
hmm. there used to be a forum topic filled with stock roms (they still required hard spl) but I can't find it... Is it still up? the files were on mediafire.
Bricked by password utility
Maybe this deserves it's own thread but I may have found a way to brick an HTC Ozone by setting and removing the password.
I got the phone 4 days ago and after messing around with the installed applications and finding some of them lacking I looked at alternatives. First I installed a version of Keypass for WinMo6.1 smartphones (the beta version since the older version doesn't support smart phones) and the basic functionality seems to work fine. Then I then I tried to install Opera Mini but there appears to be no JVM on this phone so the install file was not recognized by Windows. Then I tried UCWEB and ended up uninstalling it after a few frustrating moments trying to get it to open any page other than the UCWEB home page. So I removed UCWEB and installed Skyfire. Unfortunately I didn't install the latest version and foolishly clicked on the update button when Skyfire started up. The update feature appears to be broken and it leaves you with a Skyfire that won't run and won't uninstall. After a few hours searching for solutions and trying various options I gave up and did a hard reset from the OS. This appeared to work fine and since it was late I went to bed. I should mention that all of the 3rd party apps were installed to a 2GB micro SD card and that I took the card and SIM out when I did the hard reset.
The next day when I powered up the phone I got a screen with colored bars, which I remember reading was a boot loader screen. The phone had appeared to reset properly the night before but I didn't do more than scroll through the home screen before powering it off with the end button. From the boot loader screen I had to pull the battery to shut down but when I powered it up again things seemed fine. I installed the Google maps application (highly recommended), downloaded and installed latest version of Skyfire and installed the Google search application and everything seemed to be fine. I decided that I should try out the password lock feature and set an eight character alphanumeric password with two special characters and two capital letters. I used it for the rest of the day to surf the web, send some texts and plot driving paths with Google maps. I found the password lock a bit annoying but never had a problem unlocking after the device went into standby or after I shut it down. That night I downloaded a couple of largish (150 MB or so) MP3 audiobooks from netlibrary.com but couldn't play them with the included Windows Media Player. Despite having MP3 extensions WMP wouldn't open them and clicking WMP from the start menu appeared to do nothing. Then I tried to re install Keypass and got an insufficient memory message. I deleted some photos and a short video I'd taken with the phone software and did a soft reset (power cycle) but no joy. Unable to play my MP3 files or install keypass and getting the occasional memory warning I decided a hard reset was in order but waited until the next day.
The next morning, after the phone had charged all night, I decided to remove the annoying password lock and then shut down and restarted the phone in order to verify that the problems I'd had the previous day still existed. I navigated to the Security settings and unchecked the box about password protection then powered off the phone. When it came on again it asked for a password. Annoyed, I hit the soft key under the "UNLOCK" notification and keyed in the password I thought I had just disabled and got a screen that said "Alert The password you typed is incorrect." I'd seen this a few times before since my thumbs are not optimally sized for the keyboard so I entered the password a few more times taking care to get it exactly right. It seems that my password has been removed but the requirement to enter a password has not. I tried a blank password but it won't take one it just reiterates the UNLOCK prompt. I have the password written down, it's also a variation of one I've used a lot in the past, and I'd used it successfully dozens of times the previous day so the likelihood of my having "forgotten" it is pretty low. I called Verizon and after they suggested entering a blank password I tried again and reported the failure. Their only suggestion was a visit to a Verizon store to "re flash" the phone which I assume means reload the ROM image.
I found the hard reset suggestion below and tried it. I assume the DOWN key is the bottom D-Pad key and the SEND key is the green bracket key with the microphone icon to the left of the D-Pad. I tried holding the DOWN and SEND keys and hitting the power key until the HTC logo came up and the phone buzzed briefly and I tried holding the keys down until the phone booted to the UNLOCK screen but nothing changed the boot sequence. So I guess my phone is bricked and I'm on my way to the Verizon store shortly to see what they can do. I also noticed that the phone occasionally emits beeps for no apparent reason at random times while entering the unlock password. Also, there is an Alert message behind the UNLOCK icon that says "Alert There is not enough free space to download message. Please free up some space". I wonder if in my efforts to download a few hundred megabytes of MP3 files (audio books) I managed to clog the memory and that I can't unlock the phone because there is a memory logjam of some sort. While downloading the MP3 files I did have to kill Internet Explorer from the task manager a couple of times as it seemed like the download had hung and I couldn't find the downloaded file anywhere on the storage card or in system memory. I haven't installed anything to system memory and with a 2GB card I don't think I've come anywhere close to filling it up. I had about 500 MB in files on the SD card at one point but I deleted the extra install files and some other stuff I'd downloaded. When I put the SD card in a USB reader hooked to the PC I see 378 MB of files with 1.46 GB of free space.
I'm pretty convinced that the OS is buggy (it is Windows after all) and that I need to avoid the password utility and downloading large files until I figure out what the safe combinations of activities are.
Assuming they can resurrect the phone or give me a new one I'll try to set and clear my password at the store and see if that reproduces the problem.
Meanwhile I'd be interested in any sort of hardware based hard reset procedure that works with the Ozone since holding the green SEND button and Down D-Pad key while powering up does not work in this situation. Perhaps the fact that I can't power down and I have to remove the battery to shut the thing off is a problem but I would expect a hardware reset to work no matter what the state of the software is, even if the memory system were full of garbage. I guess designers have gotten away from dedicated reset buttons but software based hard reset mechanisms seem doomed to failure of the sort I am experiencing.
I'll report back my experience at the Verizon store when I get back. I suspect they won't be able to do much other than give me a new phone since I can't get the Active Sync software to even talk to the phone in this state. Maybe they have a lower level software tool to unbrick me; we'll see.
Max L.
ookba said:
You can do a Clear Storage from bootloader by turning off the device. While holding volume DOWN key and SEND key, power on the device. Follow the prompts.
If that doesn't do it, it's bricked.
Click to expand...
Click to collapse
Wow.
Sorry, I got bored halfway through your discertation. However, I did note a mistake that you made.
Hard Reset: A guide for long-winded users.
Step 1: Power down the phone. If your phone is already powered down, you may skip this step. Note: Removing the battery, while technically powering down the phone, is not the correct method to make the following steps work.
Step 2: With your left hand, press and hold the VOLUME DOWN button that is located on the side of the phone. Continue pressing the VOLUME DOWN button and press the SEND button. With both the VOLUME DOWN and SEND button pressed, use your right hand to press the POWER button.
Step 3: A gray screen will appear asking you three options. Pressing the VOLUME UP button on the side of the phone will be the correct option to hard-reset your phone to ROM default.
Step 4: Press SEND to verify choice.
Step 5: Cuss loudly because you forgot to back up contacts, calendar, and email. (Optional: Crying like a little girl always makes things better.)
There you have it, a true hard-reset.
NOTE: The D-PAD is not Volume Control. Utilization of the D-Pad in this operation will result is user failure.
HTC Hard Reset from password lockout solved
I had managed to lock myself out of my phone by setting a password and then unchecking the password required box under the security settings and power cycling the phone when I got low memory alerts (see previous post).
I was able to hard reset my phone by removing then replacing the battery to power the phone down then holding the VOLUME DOWN button and SEND keys at the same time while pressing the power button to bring up a menu that allowed a hard reset. You can follow the menu prompts from there. If you power the phone down normally this still works but if you are locked out with a password you can't power down normally.
My lessons learned are:
1. To hard reset a password locked HTC Ozone hold VOLUME DOWN and SEND while powering up.
2. If you get a clueless Verizon rep call back later as they do have some helpful people in tech support
3. I've yet to find anyone helpful at any of the nearby stores so that avenue was a waste of time and gas.
I've written up a more detailed account of my saga that has some other useful phone numbers and resources should anyone have special problems with their HTC Ozone phones.
When I first had the password lockout I called Verizon and after after some basic efforts to trouble shoot they said go to the Verizon store for a re flash. At the Verizon store (Waldorf, MD) they said, after 15 minutes or so of waiting, that they couldn't do anything for me. Back home I called Verizon again (866-406-5154) and got someone who was much more helpful but still unable to fix things. It seems these phones are new enough that the Verizon techs don't know the tricks yet. They did provide a number (800-229-1235) for Personal Communications (http://www.pcdphones.com/formerly UT Star Com) but that number is only staffed from 8AM to 5:30PM M-F (not sure which time zone). However the voice message mentioned a hotline number (866-806-9990) which I called. This referred me back to the 800-229-1235 number for "unlock code" issues but I stayed on the line anyway and got someone who tried to help me out. At some point they mentioned holding the DOWN VOLUME button and SEND button while powering up the phone. They thought this would clear the memory but not the password setting. I tried it anyway and it worked.
While pressing both the Volume Down button and SEND button you need to hold the Power/END button in for a second or so until you see the following menu screen (the misspelled "resotre" is exactly how the menu appears):
Wiping user data/settings &
any user installed applications...
1. Press VolUp to restore
manufacturer default.
2. Press VolDown to resotre
custom configuration.
3. Press other keys to
cancel.
At this point pressing the VolUp button gets you a screen that says:
Are you sure
you want to wipe your phone?
Press Send Key to confirm,
and any other key to cancel.
Pressing the Send Key results in:
Restoring . . .
Wait for completedwhere the second line is in red
After less than a minute you should see:
Restore completed
Press Volume Down to restart
Pressing Volume Down restarts the phone.
First you see the HTC boot screen for about 40 seconds followed by the Verizon splash animation. Then the green Windows Mobile Version 6.1 boot screen comes up about for 90 seconds while the back light flashes on and off a few times. Finally, if you have a SIM card installed, a Change Mode window appears with the following message and OK above the left soft key:
SIM card detected. Your device will now
switch to Global mode.
Pressing the left soft key brings up a Press SEND to activate your phone where SEND is actually an icon of the SEND button. Pressing SEND dials *228 and displays a GEAR icon and the text Programming in progress... . . ." while voice propmpts tell you "To program your phone press 1 . . . "
Pressing "1" plays some badly encoded music along with the text "Connected:" followed by a timer and "SPL unlocked" in red below it.
After a minute or so the screen displays "Programming was successful. Please Wait. Your phone is being reset."
Then, the phone restarts and comes up at the normal home screen displaying the time and date. From here you can restore or set up your applications and data.
So if you back up your data you can even recover from a lost password or a "friend" that locks your phone. I suspect there may be a way to unlock the password without wiping the phone by getting an unlock code keyed to the phone's serial number of DEC number (found under the battery). I didn't need this service as I just got the phone and hadn't put any data on it. If you back up the data and applications with Active Sync you should be safe but I haven't played with active sync much so I can't vouch for its stability and performance.
Hope this helps others with this phone. It's really nice when it works but it seems to have a few software pitfalls as well. Feel free to move this to an HTC Ozone forum should one be set up in the near future.
Max L.
Hard Reset
hi,
i am tried to do the same but still my phone shows HTC logo screen
how i can fix the briced phone
i am in Qatar Middle east (out side of US)
help me to fix the my lovely phone
Great Guide!
Thanks for posting this! My HTC Snap has a broken screen and I wanted to hard reset before I sold it. This was the only place I could find instructions with enough detail to do it without seeing what I was doing!
Hi all
first post and i got an interesting problem with my phone which i qualify as stupid. It all started when when my virtually keyborad started becoming unresponsive and when i tried to do a factory reset, i could not enter the 1234 number to start it. i left the phone for a while and then i could not get into the setting even . But i could receive calls but i could not call since i could not access any numbers on the dial pad( by pressing on the numbers of coruse but from dial log screen i could)
Anyway long story short while fiddling with the phone , i thought the lock feature was on that is why some of the touch functions was not totally responsive but to my sadness, i activated the lock and now the phone is stuck on the front page and i cannot access anything since i must press unlock at the far corner of the down screen but stupidly, while pressing on the unlock, since it is unresponsive, i cannot unlock the phone to get to the normal menu and so on.The only thing working is the square pad which tells me to press cancel then unlock to free the phone for normal use
By the way the lock feature is the one that blocks the phone so that you do not accidentally press on the touch screen and activate a program and not the lock thing operators put to limit your phone
I want to know if anyone can help me unlock the screen so that i can reset the phone or alternatively any other method via usb to reset my phone to factory settings. Any special buttons on the phone i can do to do that?
I tired leaving battery out for 24 hours but that did not work to unfreeze the touch buttons
Was thinking to reload the windows mobile completely via the micro card (which i read here) but i am not sure it will work or i fear it might brick my phone
Any suggestions will be welcome please.... thanks
Use myMobiler to control device from Pc through usb
Good luck
Ps: you'll probably have to change digitiser afterwards
Well tried the mobiler but the thing is that it asks the phone to allow the program to conenct and i cannot press yes on the touch screen since it is frozen or something so i am stuck again.
Very strange, it doesn't ask anything on my device...
Why don't you hard reset: press green and red buttons and while pressing, poke the stylus shortly in the reset hole then release the 2 buttons. It will ask something that you probably won't see, just press the action button and wait for it to restart.
Don't flash another on just yet - it may well cause issues as it sounds like your digitizer is broken. Don't hard reset either
Does it pick up anything at all? Have you tried tapping all over the place in that region to try and get a response, sometimes just under the screen also works. Do you use a screen protector? If not, try it with one, if yes, try it without, it may be interferring with it, or it may help the touch be picked up by the phone (Stupid, I know, but this is something I found to work before with my elfs, and omnias)
When it is locked, is activesync picking the phone up? You may be able to put the remote.exe into the windows folder (for myMobilier) and do it that way.
A digitizer costs about £6-£10. But due to the age of this device, as sad as it is, I would suggest trying a new phone out if funds allow for it.
ok so far i tried the hard reset (red button and green and pressed the on off button but nothing. When i press on off button alone it switches off but not hard reset. I did not know i had a reset hole at the bottom of the phone.I did that with red and green button but nothing. Only when i poke the hole alone it does a hard reset i think but when i switches back on it is still unresponsive and locked screen
I tried poking under screen protector nothing. Also i think screen is still responsive because when i tap on it, the screen lights brighter
I tired putting remote exe file on the phone( active sync is working and i can read files on the phone) but i have two remote files..which one to use ? the one that ends with 40 one or 50 .Also where to put it specifically..which folder.I tried my windows mobile based device but nothing.Also tried program files and data application nothing.
Mobiler cannot connect since from pc alone because it asks my phone permission
and i cannot tap yes to accept program.
so any more suggestions please
Hi
Maybe I wasn't clear enough, here's the exact procedure, it should work since you have to use only hardware buttons:
Hold down send/reject buttons (green/red at the front) and reset with the stylus; release the stylus but keep holding the buttons till you get 'this will erase all your personal data' message, then press 'action' (big front button) to hard reset.
If Hard reset doesn't work then your device hardware is faulty.
If he hard resets he will liekly not be able to align the screen on initial setup tito12.
Avanisha. If you try to run one of the remote.exe it will say this is not a valid windows application, thats the one that needs to go into windows on your phone.
captainstu72 said:
If he hard resets he will liekly not be able to align the screen on initial setup tito12.
Click to expand...
Click to collapse
Hi captainstu72, i was under the impression that he messed up something in his system so a hard reset would hopefully solve the problem. In case he still can't align the screen after HR then he has to replace the digitiser. Mymobiler will not solve anything, pls read the 1st post: he wanted to do a factory reset. He just have to sync before HR.
thks tito 12..problem was solved with your help.J ust did not get the steps of hard reset right. Phone is working ok now and screen is ok as well as tap function. thank god i don't need a digitizer. thanks to captainstu72 for the help as well .You were right tito..seems i ran a program and then all hell broke on my phone. I wanted to factory reset but as you know the pad was locked.
Glad I could help, enjoy your device
Ahh okay, guess i mis read something! Sorry
Glad its all sorted though, I was just concerned he may end up in an annoying align screen loop
I have an HTC surround. I am having a problem sliding up the lock-screen. It takes number of attempts to slide up the screen. Sometimes it results in missing the incoming call. It appears to me there is a mechanism (an observer) which negates the touch event if the phone is in pocket while the phone is locked. In my case, even when I am sliding the lock-screen up with my finger, the observer is negating the action and the lock-screen comes back from 20% slide-up. Other than that, the touch-screen is working perfectly fine.
Q:
Is it a software or hardware issue?
Is there a workaround (something like hacking into the ROM and playing with the drag sensitivity)?
Should I dump it and consider myself "done with the WP7"?
P.S.
1. I got this unlocked ATT phone from US and now using it in middle-east.
2. (Not sure but) I have heard that ATT only return the phones with monthly contract.
3. The problem started after 12 days of first use.
4. I tried hard and soft reset, with/without nodo and latest updates. But it’s still the same.
It sounds most likely like it is just an inconsistent/bad touch panel on the hardware. You could attempt to replace it yourself by purchasing another one on eBay, but I doubt that any software fix would be able to fix this behaviour. I have a Samsung Focus WP7 and this never happens, the only time the lock screen comes back down is if you lift your finger before getting to the top. So my best guess is that the touch screen just cuts out before you can get the phone unlocked. Sorry....
I have the same issue. Does anyone have a solution, please!!. I'm in another country, so I can't return it. Have to fix it!
same issue here.
Do you have anyone in the US that you could send it back through? You might also try contacting HTC directly. I believe the phone has a 1 yr warranty on it. At least that's what Asurion told me when they sent me one as a replacement for my old Tilt 2.
My Phone have same problem, i install NO-DO next install PreMango but not helped.
I have no such issue with my sourrond, with mango 7720 and speech for phone accessibility turn on you only have to slide less than a inch to unlock screen...
A possible answer
After some researching i found this in one of the forums of HTC
Display Not Working on the HTC Surround
Black/Blank Screen
Verify that the battery is properly installed in the device.
Attempt to power the device on by pressing and holding the power button for 3 seconds.
If the device won’t power on (also indicated by no LED’s) attempt to charge the device. If there is no response from the device when attached to a charger and power source, treat the issue as a Power/charging issue.
If the device will or is powered on:
Verify that the device is not in hibernate mode by pressing the Power Button once.
Once you have verified that the device is not in hibernate mode, attempt to navigate the device by using the Hardware buttons.
If the display is still black/blank, Soft Reset the device by powering it off and removing the battery for 10 seconds and then reinsert and Power the device back on.
If the screen is still black/blank after the Soft Reset, you will need to perform a Hard Reset.
The hard reset will remove all of the customers’ data and settings and restore the device back to the state that it was in out of the box. Once the Hard Reset is done, the customers’ settings and data CANNOT be recovered. If possible, have the customer back up their data before proceeding with the Hard Reset.
Once the Hard Reset is complete, retest the device.
If the screen is still black/blank, the device will need to be replaced/repaired.
Screen has lines
Is the customer using a custom picture or image as their wallpaper?
Return the Wallpaper settings to one of the defaults on the device by going to Start>All Applications Arrow>Settings>Lock & Wallpaper>Change wallpaper
Is the issue seen when using the default wallpaper on the device?
If so, Soft Reset the device.
If not, advise the customer that the issue is with their custom wallpaper selection and recommend that they discontinue use of it.
Does the issue remain after completing the Soft Reset?
If so, rule out recent 3rd party applications that might have affected it, by removing them
Start>All Applications Arrow>Touch and Hold on an application to be removed and select Uninstall from the Pop-up menu.
Note: Not all applications can be uninstalled from the device.
Once all recent applications have been removed, power cycle the device and retest.
Is the issue seen after removing recent 3rd party applications and performing the Soft Reset?
If so, perform a Hard Reset.
The hard reset will remove all of the customers’ data and settings and restore the device back to the state that it was in out of the box. Once the Hard Reset is done, the customers’ settings and data CANNOT be recovered. If possible, have the customer back up their data before proceeding with the Hard Reset.
Once the Hard Reset and retest the device.
If the issue remains, the device will need to be replaced/repaired.
Unresponsive Touch Screen
Note: The device comes with a Capacitive Touch screen which will not respond to light touches from anything other than the flesh of the finger. Users trying to use their fingernails or any other object should be advised that they need to use the flesh of their fingers (firmly) to navigate the Touch Screen.
Verify that the issue is with the Touch Screen and not the device freezing by attempting to navigate the device using the hardware keys.
If you can navigate the device using the Hardware buttons, continue.
If you cannot navigate the device using the Hardware buttons, this issue needs to be worked using the troubleshooting flow for Device Freeze.
Check the device for a static cling screen protector, if present, remove and retest.
If the issue remains, Soft Reset the device.
Check the device for a carrying case with a magnetic closure; some magnets can interfere with the Touch Screen responsiveness.
If using one of these cases, have the user remove the device from the case and retest.
Ensure that the Charger/Data Cable is the one intended for the device by HTC.
Use of non OEM chargers/data cables can cause your screen to become unresponsive (due to the power being allocated to charging the task, and not the screen).
HTC can only guarantee items such as chargers that have been made, made for and certified by HTC. Our chargers have been tested and passed strenuous quality and safety regulations, and it is recommended you only use HTC chargers with your phone. You must be very careful when using electrical appliances; using products that have not been tested properly or that have not been tested at all could cause your phone to malfunction, or even in extreme cases, could injure you.
If the issue is not resolved by the previous steps, move forward with the Hard Reset.
The hard reset will remove all of the customers’ data and settings and restore the device back to the state that it was in out of the box. Once the Hard Reset is done, the customers’ settings and data CANNOT be recovered. If possible, have the customer back up their data before proceeding with the Hard Reset.
Once the Hard Reset and Customization process have completed, retest the device.
If the issue remains, the device will need to be replaced/repaired.
Hope someone can give us a better answer, but this is the best at the moment
UPDATE:
People if you want to fix your Phone just put this on the serch engine of XDA Developers "To solve the problem "Screen unresponsive" or "Frozen screen" by yourself", without the brackets.
The post is from "maybeture", and he say is working, if you read the replies, many people said it work
I'll do it to tell you
Tell me If you have luck
same problem it must be that it gets unresponsive for a few seconds or even minutes after screen turns off i have to slide it sloooowwwly to get it maybe its some loose cable in there dont know but really waiting for it to be hacked to have android
Same problem here with my father's phone. I'm going to replace the screen digitizer tomorrow and see if it works... it only costs 19 bucks so its worth the try...
jo
jesusodin said:
Same problem here with my father's phone. I'm going to replace the screen digitizer tomorrow and see if it works... it only costs 19 bucks so its worth the try...
jo
Click to expand...
Click to collapse
Hi JesusOdin
I have the same issue but my question is
And all is right now?
I you have luck please tell me
Thank You
I've had similar issue with the lock screen at times. The problem is more persistant when the phone is in the pants pocket during hot weather or I am under heavy exersion. I think it may be related to the humidity. I have refrained from storing the phone in this pocket and rarely have any issue.
The phone is not weather resistant, an Otterbox might help but would be rather bulky.
was there ever a solution to this lock screen problem?
i heard it was something to do with the drivers...changing from v69 (at&t) to v63(t-mobile)
anyone know how to do this?
Well...
Tried to replace the digitizer and ended up cuting the ribbon cable of the display. I bought the screen and digitizer. Replacing the parts on this cel is not for the weak of heart.
The cel did work without problems afterwards.
I have a surround and lately its misbehaving.
The screen goes off within a second or two if I do not continue touching it. Sometimes it doesn't even stay for a second and goes off immediately. When the screen goes off, I notice the red battery light blinking. Sometimes its just in a reboot boot loop. If i am successful and able to reach videos and start a video, then the video plays fine.
Until the video is playing, the screen doesn't go off. I have tried a hard reset but it didn't help. I am on mango.
What might be the problem?
Hello,
I have a problem with my "sharp softbank aquos 402SH
I setup a pattern lock. Since I have not used the phone for some time I cannot remember the pattern anymore.
I thought an unlock with a hard reset is no problem. But I found no way to boot into recovery mode(tried power and minus button, power and plus button to boot).
Also the device did not show up in adb as a device(Windows 8/Sharp USB driver installed) but was recognized as a storage device.
The user manual says:
"Do not forget pattern, Lock No. passcode or password set for canceling Screen lock(write it down if necessary). If you forget it, visit the nearest SoftBank Shop for recovery procedure."
As I live in Sudan and there are only softbank stores in Japan. So this is not possible for me.
Is there any other way to hard reset the device?
same prob
http://www.recovery-mode.com/android/sharp-aquos-crystal-x.html
Are you sure? Have you tried power-cycling the device? (Let it discharge all the way, and charge it all the way.)
Sharp aquos 402 sh hard reset problem
I have the same problem as the guy from sudan mentioned above, ive forgot screen lock pattern and not been able to get into boot option by hard reseting. I have done every thing like keep pressing and hold volume down key and holding power on key after sharp logo appears i let go the keys but nothing happens. Plz suggest me the solution.
Hi there
i have the same problem
my phone aquos 304 there are no available physical volume rocker button
i forget the password pattern
custom cable data with R jumper to ID pin with zadig software cannot flash the twrp
could someone help me out of this
thx
i also have that kind problem also show to many people but no way found of any to recover my bally please do something
As I think this phone did not get that many updates this might still work. I remember early on back then that i somehow managed to make a pattern that I had not meant to so could not unlock. Also quickly found out I could not get into the bootloader. But I found out you could bypass the lockscreen if you went into the emergency call screen. The thing is, you'd have to make a call then you could use the drop down notifications and enter settings app or something like that. I can't remember clearly, but I could atleast get access. And from there i just disabled the pattern. Don't feel I can recommend this though as it depends on how quick you are, and police services are sort of being misused this way. I remember being frazzled and extremely annoyed at that point as I had only had the phone for a couple of days. Ended up spamming a call three or four times to the cops to bypass without connecting a call. They called me back wondering what the deal was ? oops.