Hi guys,
My SP3 stucks on bootloader
Spl Version is Typhoon SPL 2.5.0102 (I think it might be CID lock)
i had tried many of the things but no avail
I installed many of the roms ,it only changes spl version from 2.5.... to some other 2.XXXX version and then stuck on bootloader
i can't even use spv-service to unlock it
i don't want to use imei-check.co.uk and spend $40 on it
Please Guide me to solve this problem
Maybe you flashed your phone with 3rd party ROM without doing supercid. So try to flash your phone with original rom.
my phone was unlocked form super CID and i already tried to flash it with original rom but nothing happened . It starts and stuck on boot loader
Related
Hi i have 2 part question my phone is an htc 8125 cingular sim card unlocked phone it has windows mobile 5 on it and i have the IPL 1.05, SPL.3.08 on it.
I did this but installing the IPL_SPL_3.08 rom. Anyways Im trying to get it back to IPL 1.05, and SPL 1.05 by installing the button rom and i seen the beer screen and it loads up to windows mobile 5 but keeps staying at IPL 1.05, and SPL 3.08 is there away to get it back to 1.05,1.05. I tried a few methods but aint working. Would keep reflashing a few times with the button roms get it back to 1.05,1.05. I tried with, newromupdateutility_wizard_noid. and didnt work i tried with rom update and didnt work. When a rom loads up and gets stuck at 99% and then i get a message with activesync saying lost communication error message whats does that mean and it saying try restore.
Also can windows mobile 6 with touch flo install on this phone or no. I was tring to do that with but all i got was it going back to windows mobile 5 and doesnt upgrade to wm6. Do i first need it to get it back to 1.05,1.05 using the button rom then use ,lokiwiz02b to do the unlocking(mind you my phone is all ready sim unlocked). and then flash a t-mobile or cingualr rom and then do the update with a windows mobile6 rom.
Whats a good windows mobile 6 with touch flo that works good on this phone can u maybe post a link
thanks for the help
deleted for inaccurate information
First,you shud have CID unlocked the phone prior to upgrading to 3.08 bootloaders,cuz it becomes very difficult and frustrating to downgrade from 3.08 to 1.xx.Now the only way is to first try to downgrade to 2.xx by flashing the official carrier's rom and when completed downgrade to 1.xx through Button's 1.05.You can only CID unlock the phone,if its 1.xx,which you already know.
Secondly,it'll only upgrade to wm6 if its cid unlocked.Try to flash ipl/spl 3.08 again and make both ipl/spl 3.08 first and then downgrade to 2.xx by flashing the official stock rom,it might work.
Cheers!
Hi !
My P4350 got stuck in the bootloader when I stied to flash a new ROM
Active sync doesn't recognize the P4350 anymore....
IPL 5.04.0002
SPL 4.10.0000
What should I do now ????
search for bootloader... there are so much threads with the same question
Did it fail during the flashing process? Do you see an error message on the bootloader screen? ActiveSync won't recognize the device unless it is booted up in Windows Mobile. If you can still get into the bootloader reflash the ROM from there. You don't have to flash ROM's connected via ActiveSync; you can do it from the bootloader as well.
It did fail during an flash !!
The only thing on the tri colour screen: is: IPL 5.04.0002 and SPL 4.10.0000
When I try to flash a new rom it gives errors, it starts for 2 seconds and than it stops with an error. (on several occasions different errors ==> one error at the time).
Post some of the error codes you get. Have you tried flashing a different ROM? You may need need to use MTTY if you get a ROM upgrade code message in the bootloader itself.
Ehhhhhhh what is: MTTY if you get a ROM upgrade code message in the bootloader itself.
I have NO idea what you mean.
I had before an TyTN and that was no problem ever (until it died..)
Miep Miep Zoeffff said:
Ehhhhhhh what is: MTTY if you get a ROM upgrade code message in the bootloader itself.
I have NO idea what you mean.
I had before an TyTN and that was no problem ever (until it died..)
Click to expand...
Click to collapse
Is ur device CID unlocked(HardSPLed)?
Miep Miep Zoeffff said:
It did fail during an flash !!
The only thing on the tri colour screen: is: IPL 5.04.0002 and SPL 4.10.0000
...
Click to expand...
Click to collapse
I'm a retard. You don't have HSPL flashed to your device. This is why it keeps failing when you try to flash a ROM. The HTC SPL on your device is blocking you from flashing unsigned (custom) or CID-mismatching ROM's to your device. All you should need to do is flash HSPL and then your custom ROM. Read the Wiki for this device if you need more information.
My phone was provided by Vodafone.
I have now Telfort.
I flashed Vodafone to Canonyang.
Then I tried to put the Dutch back on it and then it got stuck in the Bootloader.
Wasn't it hard SPL than??
Digital Outcast said:
I'm a retard. You don't have HSPL flashed to your device. This is why it keeps failing when you try to flash a ROM. The HTC SPL on your device is blocking you from flashing unsigned (custom) or CID-mismatching ROM's to your device. All you should need to do is flash HSPL and then your custom ROM. Read the Wiki for this device if you need more information.
Click to expand...
Click to collapse
I've tried 2 different HSPL now.
It goes well, even says 100 % on phone AND computer but than it gives error 270 'update error'
What now...
Have you followed this? I know it works for me...
I've seen it, but where do I have to intall the 3 cab files?
Do I have to install them on the microSD card?
Do I have to put them like this .cab or do I need them to unpack them??
please help!
Copy them to your phone, install all three on your phone's memory.
ehhhhhhhhhhhhhhhhh How should I do that ??
Oh right. I'm retarded. You're stuck in the bootloader... Sorry just reading too many threads and getting confused. Have you tried searching for "bootloader" or "Goldcard" in the ROM development forums? There are tons of explanations on how to recover from being stuck in the bootloader.
i have rogers htc touch, after trying unlocking using ELF USPL , when i power on only see HTC Logo and then it goes off, i try loading new rom but still same problem . Please help
What is your IPL and SPL?
IPL is 2.21.0002
and
SPL 1.11.0000
I had the same problem...took me 3 hours to figure it out..
1. on Bootloader, re-install a ROM that works (go back to WM6 or WM6.1)
2. when it working, install USLP 1.11
3. DO NOT RESET AFTER...
4. install USLP 3.14
5. then you can install any WM6.5 ROM
For some reasons, the Rogers Touch has some difficulties to upgrade directly, even if it's unlocked...
Good luck
Michel
michel-2000 said:
I had the same problem...took me 3 hours to figure it out..
1. on Bootloader, re-install a ROM that works (go back to WM6 or WM6.1)
2. when it working, install USLP 1.11
3. DO NOT RESET AFTER...
4. install USLP 3.14
5. then you can install any WM6.5 ROM
For some reasons, the Rogers Touch has some difficulties to upgrade directly, even if it's unlocked...
Good luck
Michel
Click to expand...
Click to collapse
Thats a great tip to the community, I will refer back to your guide if I met with anyone with troubles using Rogers.
...thanks...
But, after reading a lot yesterday, seems that the USLP 3.14 is a ''battery eater''...
I'm testing it now..I will see in a couple of days if it is the case!
So far, it looks like it's using approx 2% of the battery per hour...
Definitely, you should always use 3.10.
I had a bad experience with 3.14, it takes up half of my battery after 5 hours of almost no usage.
i'm confused. .... i also have a rogers htc touch as well and i want to flash a custom rom onto it.
(my IPL: 2.21.0002 and SPL: 2.21.0000)
First, i know it has to be CID unlocked... using >> Elf 1.11 USPL ?
Can i use HARDspl ?? What is the difference between USPL and Hard uspl ??
Because i read something about ..... " HardSPL : This modified bootloader allows a much safer flashing process to take place since it reduces the chance of permenently bricking your device. It also removes the need to CID Unlock the device since it ALWAYS reports SuperCID when flashing. "
After a CID unlock and soft reset, the phone will reboot into the old ROM (Rogers, in my case) if i have not began flashing a new rom ??
Some advice please... thanks!
Use the guide written on 4th post.
Its located on this thread
Cheers.
Hi,
I have tried to flash a wiza200 that was already flashed with a manila rom, I checked that it is a G4. I used TNT.20273 Professional Wizard HTC Home FREE ROM, it seems to work , romupdate utility indicated that the device was flashed successfully but it reboots on bootloader screen. I tried to reflash it it gave the same result, I tried another rom but impossible to flash it with other roms. So I downloaded the official one from the operator O2 but I got "invalid vendor" message. I searched all the possible solutions but none of them worked( wizard love also). Is there a savior here ? someone who can give me the right procedure to follow.
initially the IPL was 2.21.0001 and spl 2.21 Olipr
now the IPL is 2.21.0001 and spl 2.21
Thanks
Best regards.
You must replace the Update.exe with a MaUpgradeUT_NoID.exe . Found here in Forum . Look in "Blue Angel" for it. Be sure that you flash the right ROM with it . It will no ask...
Hi All,
I need your help in urgent!!!
My ELF GSM infor:
- DeviceID: ELF011000
- CID : DOPOD701
My ELF worked fine before I tried to upgrade its IPL from 1.11.0002 to 2.26.0002, then this problem occur. Because a WM 6.1 ROM requires to have IPL 2.27.0002 and SPL 2.28.0000 so I kept continue upgrade the IPL/SPL to 2.27.0002 and 2.28.0000.
I tried to flash my ELF, from bootloader mode, with these ROMs:
- RUU_Elf_DOPOD_chs_1.11.706.1B, this ROM I got from a China forum, it is my device original ROM
- RUU_Elf_DOPODASIA_WWE_1.11.707.1B_4.1.13.42_02.93.90_Ship.exe
- RUU_Elf_DOPODASIA_WWE_1.17.707.2B_4.1.13.46_02.97.90_BLUE_Ship.exe
- RUU_Elf_HTC_Asia_HK_WWE_1.15.721.3B_4.1.13.46_02.97.90_BLUE_Ship.exe
- ESSential_4_5
- Onyx_jr_4_4_2_Light
They are all 100% successfull but the IPL/SPL unchanged (2.27.0002 and 2.28.0000) and the device still loop at smart mobility, can not jump into OS.
I did try to use unbricker ROM and goldcard (with original ROM or unbricker ROM inside) but the ELF still stuck at smart mobility...
Please give me your advices, what should I do (except buying a new phone)?
Thanks for your time!
Flash your Official ROM
rockerboom said:
Hi All,
I need your help in urgent!!!
My ELF GSM infor:
- DeviceID: ELF011000
- CID : DOPOD701
My ELF worked fine before I tried to upgrade its IPL from 1.11.0002 to 2.26.0002, then this problem occur. Because a WM 6.1 ROM requires to have IPL 2.27.0002 and SPL 2.28.0000 so I kept continue upgrade the IPL/SPL to 2.27.0002 and 2.28.0000.
I tried to flash my ELF, from bootloader mode, with these ROMs:
- RUU_Elf_DOPOD_chs_1.11.706.1B, this ROM I got from a China forum, it is my device original ROM
- RUU_Elf_DOPODASIA_WWE_1.11.707.1B_4.1.13.42_02.93.90_Ship.exe
- RUU_Elf_DOPODASIA_WWE_1.17.707.2B_4.1.13.46_02.97.90_BLUE_Ship.exe
- RUU_Elf_HTC_Asia_HK_WWE_1.15.721.3B_4.1.13.46_02.97.90_BLUE_Ship.exe
- ESSential_4_5
- Onyx_jr_4_4_2_Light
They are all 100% successfull but the IPL/SPL unchanged (2.27.0002 and 2.28.0000) and the device still loop at smart mobility, can not jump into OS.
I did try to use unbricker ROM and goldcard (with original ROM or unbricker ROM inside) but the ELF still stuck at smart mobility...
Please give me your advices, what should I do (except buying a new phone)?
Thanks for your time!
Click to expand...
Click to collapse
First try to flash your official ROM and then try to flash ipl/spl again follow step by step. After that try to flash customize ROM again. Hope you will success.
Dear ELF341,
Thanks for your advice!
When I flash the original ROM, 100% successful, then my ELF loop at the China Mobile screen then reset... I don't have the IPL1.11.0002 and SPL 1.11.0000, the lowest I have is IPL1.17.0002 and SPL1.17.0000. I tried to flash back the 1.17 version, after 100% successful, enter bootloader, the IPL 2.27.0002 and SPL 2.28.0000 still remain!?
Please tell me how to do!
Thanks for your time!
rockerboom said:
Dear ELF341,
Thanks for your advice!
When I flash the original ROM, 100% successful, then my ELF loop at the China Mobile screen then reset... I don't have the IPL1.11.0002 and SPL 1.11.0000, the lowest I have is IPL1.17.0002 and SPL1.17.0000. I tried to flash back the 1.17 version, after 100% successful, enter bootloader, the IPL 2.27.0002 and SPL 2.28.0000 still remain!?
Please tell me how to do!
Thanks for your time!
Click to expand...
Click to collapse
After flash back to official ROM , enter bootloader and check ipl/spl first.
Normally, if you flash ipl/spl (not hard spl) when you flash back to the official ROM the ipl/spl will back to original. S/R - wait for boot to WM if OK then do H/R again. And flash ipl/spl again - enter bootloader and check ipl/spl again (changed or not) if OK after that I recommended you flash Onyx ROM. I used it for long time and no trouble.
Hope, it's can help you.
Dear ELF341,
Thanks for your reply!
After 100% successful loading the original ROM, my ELF restart and loop at the China Mobile screen... When I enter bootloader, the IPL/SPL still remain as IPL 2.27.0002 SPL 2.28.0000
I understand that when we flash the original ROM, the IPL/SPL will roll back to its original version, but mine is so strange?! Does this mean that:
- My ELF's flash ROM is fail or locked at the region for IPL/SPL so that whatever ROM I flash (these ROM contain ILP,SPL,OS,radio..) the IPL/SPL unchaged?
- The original ROM is actually not match to my ELF?? But I already flashed the other ship WWE ROM and also the unbricker ROM, they all loop at smart mobility...
Please help me!
rockerboom said:
Dear ELF341,
Thanks for your reply!
After 100% successful loading the original ROM, my ELF restart and loop at the China Mobile screen... When I enter bootloader, the IPL/SPL still remain as IPL 2.27.0002 SPL 2.28.0000
I understand that when we flash the original ROM, the IPL/SPL will roll back to its original version, but mine is so strange?! Does this mean that:
- My ELF's flash ROM is fail or locked at the region for IPL/SPL so that whatever ROM I flash (these ROM contain ILP,SPL,OS,radio..) the IPL/SPL unchaged?
- The original ROM is actually not match to my ELF?? But I already flashed the other ship WWE ROM and also the unbricker ROM, they all loop at smart mobility...
Please help me!
Click to expand...
Click to collapse
How you flashed ROM ? By RUU (PC) or used microSD card. I recommened you to use RUU (PC) follow step by step. Sometime when I used microSD card to flashed ROM , it's successful but cannot boot, after that I flashed Official ROM by RUU and unlocked the phone again it's back to normal. And your official ROM, you must check with your operator or distributor because in different zone it's use diferent ROM.
Dear ELF341,
I only can flash via PC RUU, I don't succeed in SD card way:
- When I copy the *.nbh file into SD card, then enter bootloader, I just can see the checking SD card content string displayed very fast, then the tri color screen.
- When I create a goldcard and copy *nbh file into it, enter bootloader, the brick ask for 'upgrading SD image', I press power button for it to start download but it hang at 'downloading from SD' with a blank download status bar.
Actually I bought this ELF from a man on my local site, so I don't know where is the distributor...I used the mtty and usb monitor to check for my device infor, then search internet for my original ROM, I only can find in a China forum that match my deviceID/CID....
For my case, I really don't know why I can not change its IPL/SPL version? Please help me!!!
Thanks for your time!
well u hav to rename the nbh file to ELF0IMG for SD card flashing to work.