Bricked Hermes when flashing rodio - 8525, TyTN, MDA Vario II, JasJam General

Hi guys,
just seeing if anyone can help me.
I was updating my Radio when the program failed (pretty sure it was a bad USB connection)
at first I could only get to bootloader but i managed to bypass it with help on the wiki.
Now it loads to the windows splash screen and stays there.
I'm running IPL 1.04 and SPL 2.10.Olipro
I was in the process of completing resetting the phone with another ROM but I got stuck at the radio part and now my phone is screwed.
Can anyone help me out?

Sure, there is thread on reviving bricked Hermes devices here and solution to common bricking problems here. Hope it will help you ressurect the device.

Related

Herald upgrade gone wrong

I need some help!
I have a dopod C800. I have tried upgrading but have run into some difficulty.
The PDA will not go past the tricolor boot loader screen. The only writing is as follows. In the Red section.
RUU
IPL 1.09.0001
SPL 1.09.0001
I cannot get the Active Sync to go green (connect) but I know my computer can see the device as i get a sound when i plug the USB cable in.
Can help me and advise what I can do? I think i might have tried to HArd SPL.
Need help to unbricked herald
i have the same exact problem. some people say the phone is bricked.
http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES
i found this link, that shows that hermes can be fixed. Is there any justice or expert guru to get our phone unbricked
I went try to repair it and they say i gotta change the motherboard aka the machine. i was like ^&* since it cost $400, might as well by a new phone.

Help me please with my cingular 8125!!

HELLO,
I'M A NEW USER OF THIS FORUM
i HAVE BOUGHT A CINGULAR 8125
WHEN I TURN IT ON IT LOOKS BLOCKED ON THE BOOT LOADER SCREEN
THERE IT IS WRITTEN
IPL 3.08
SPL 2.G4.4PDA
ACTIVESYNC DOESN'T RECOGNIZE IT SO I TRIED IN THE USB MODE TO FLASH A NEW ROM BUT NOT WORKING
WHAT I COULD DO WITH IT?
HELP ME PLEASE
It looks like you've got a G4 device. Read the flashing guide in the upgrading section about how to flash your device. Looks like someone tried to flash a custom rom already and bricked it. Can you get your money back?
Thank you for the answer i will lok in that section
the seller said that the phone was good when he shipped to me but i'm not sure
if i will not solve the problem i think i will go with a legal advice
Usually when you brick a G4 it won't even power on anymore. That's how mine acted when I flashed a G3 ROM to it. If it shows the boot loader screen, you should be able to bring it back by following the instructions on how to flash a G4. A section on recovering is in there.

Herald Doesn't start after a bad flash

Hi everybody,
I went to a store this evening in order to unlock my Polaris. The owner of the store has got a HTC herald with a problem that he wanted me to solve.
He tried to install another rom on his herald but, due to an unsuccessfull rom upgrading, the HTC is locked on a RGB screen (red green blue) with the only following indications:
RUU
IPL 1.08.0001
SPL 1.08.0001
USB (or nothing when not plugged)
Would you mind helping me? I tried several Roms, and there was only one that seemed to work (ROM HERALD_ smiley sWWE.gif _6.1.405.13_BUILD 20764.1.4.3): It gave me a progress bar on the HTC frozen at 0% while the upgrading tool on the pc told me that I needed a more recent upgrading tool.
What can I do?
Thanks for all the solutions you'll give me
Nounou7701
(sorry for my bad english, I'm only a 15 years old french guy, wich explains that way of speaking english)
Before installing cooked ROMs I believe the phone must be HardSPL'ed, and this can only be done if the SPL/IPL is 4 or above - any lower/not HardSPL'ed and the device will be bricked. The screen you are describing is the bootloader, and since you only have an IPL/SPL of 1.x I'm pretty sure you can't install custom ROMs. To unbrick the device, turn it onto the bootloader and then load the original HTC ROM that came with the device.
Hope this helps,
czhang
Dear Czhang,
I tried several times to enter in bootloader, but it's impossible as it starts with the bootloader menu! I can't change anything about that, even by soft resets, reset+camera, reset+buttons...
Do ya think this could work properly? http://forum.xda-developers.com/showthread.php?t=417930
As I am stucked with 1.08.0001 SPL, There is nothing to do. All the users who tried to unbrick their phone didn't got it working, except one who changed the motherboard for... 200$ ! The price of a used HTC Herald in very good conditions!
Still looking for help
Thanks
Nounou7701
sorry to say sir but your ipl and spl should have been 4.0 or higher and also HardSPL'ed. i'm pretty sure your device is bricked. GL on finding a way to fix it or buying a new one. =D
Nounou7701, though you cannot flash a cooked ROM with IPL/SPL 1.x you can definitely flash the official ROM from HTC.
AAAARRRGGHHH! thanks to everyone for the (bad ) news... I'll try to buy a mothercard, just like another user did...
Have a nice evening
Nounou7701
nounou7701 said:
Hi everybody,
I went to a store this evening in order to unlock my Polaris. The owner of the store has got a HTC herald with a problem that he wanted me to solve.
He tried to install another rom on his herald but, due to an unsuccessfull rom upgrading, the HTC is locked on a RGB screen (red green blue) with the only following indications:
RUU
IPL 1.08.0001
SPL 1.08.0001
USB (or nothing when not plugged)
Would you mind helping me? I tried several Roms, and there was only one that seemed to work (ROM HERALD_ smiley sWWE.gif _6.1.405.13_BUILD 20764.1.4.3): It gave me a progress bar on the HTC frozen at 0% while the upgrading tool on the pc told me that I needed a more recent upgrading tool.
What can I do?
Thanks for all the solutions you'll give me
Nounou7701
(sorry for my bad english, I'm only a 15 years old french guy, wich explains that way of speaking english)
Click to expand...
Click to collapse
He didn't head the warning of the SPL requirements. You can easily revive it using the GoldCard method. (Search for the term "goldcard herald".)
HTC P4350 do not switch on after a bad SPL
I've tried to flash my Hera 100 P4350 with HardSPL Herald, but I got an error message it has switched off and I can't get my mobile switched on again.
It looks like completly dead (kaput).
Can anyone help me ? Or explain why that happened ?
TIA,
dark_side61
HTC P4350 do not switch on after a bad SPL
After a total reset (left soft touch + right soft touch + reset) I got the
IPL 1.08.0001
SPL 1.08.0001 screen but with no USB on the lower left corner of the screen
After arrived here what shoul I do to reinstall my P4350 ?
What do I need to have ?
TIA
dark_side
Do what Ivan said!
Search for Goldcard to fix it....

Help guys! anyone....

This is the story:
I bricked my phone (Elf) because I didn't CID unlock it after installing the Opal 6.1 rom. So when I tried to install the backup ROM I made it got bricked. I read all the threads about how to revive the phone and I can't get any to work.
I can't do the GoldCard since I don't have a working WM phone. So I tried the Wild card unbricker ROM and the phone got worse. Now I only get to the tri color screen without any "RUU" at the top and every time I try to flash another ROM on it it shuts and I get an error message saying something like "Invalind vendor or error in image" etc... Please help me, what happend??? I cant flash any ROM. I cant do hardspl. I can't do anything.
PLEASE HELP ME! Anyone who's familiar to this problem?
Thx in advance!

[Q] Urgent problem

Hi,
I've got a real urgent problem to solve. With one HTC X7500, i installed SPL 1.2...but as a stupid boy, i also installed ATHENA ROM AV.1.20.1. for SPL 3.5!! So now, the mobile doesn't start and stay on a very strange screen...but never run under WM...
I try all (using mmty...usb not recognized)...I try to flash with Athena updater... problem of connexion...NOthing is working.
The only thing i can do is to make a reset and go in the manual bootloader...but after, nothing is possible!!!
Please, help me, i need this material for my job!!!!
Thank u
If you can get into bootloader (the 3 colour screen) post what is written there
if it is definitely spl 1.2 you should be able to load an SPL 1.2 rom from this screen.

Categories

Resources