Database Users

My SVP M600 phone got stuck at Starting screen

Hi Friends,
My new mobile phone SPV M600 got stuck whil starting showing four lines of messages as shown below.
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 2.10.1.22
Can any one please help me in geting my phone to today's screen.
I also attached the screen shot for reference.

did you try a hard reset ?

Ya I tried both hard as well as soft reset but same screen is stuck again and agian.Can any one please help me in this regard as I am very new to PDA family.

Ok, first things first:
Since you are new to this, are you sure you preformed a hard reset?
It is done by holding power + camera + comm manager buttons (one on the right, two on the left) and pressing with stylus in the reset hole at the same time.
A message should appear asking you to press 'send' (green phone button) to confirm reset.
If this does not help, you may have a serious problem.
Please answer the following:
Is the device fully charged?
Phone will fail to boot if the battery is too low.
Did you install any software right before this happened?
This should have been resolved by hard reset, but just in case I am asking.
Did you change the ROM, attempted CID / SIM unlock?
This could require more serious measures than I can advise on.

I did exactly the same thing which you mentioned.But even then it is stuck at the same screen.
Ya u r right I unlocked my mobile using a software from eBay.The unlock was successfull and I tried to insert T-Mobile sim, it also captured the signal and I was able to make and recieve calls then after that I wantedly switched off the phone and then tried to start it, there got the problem.

Can any one help me in this regard please.

I am having the same problem, but my phone is not sim-locked.

I've got the same problem after attempting smart1_wm6_pp8mb.exe
I'm having the same problem with my G4 QTEK S200:
Attempted to upgrade to WM6 Rom using smart1_wm6_pp8mb.exe
After reboot the phone got stuck at the QTEK Screen
Tried Hard Reset (Camera+Power+Comm+Reset) followed the steps with the same results (bricked)
I also tried re-flashing the rom back to the factory one using RUU_Prophet_220734_2207114_024721_QtekWWE_Ship and ROMUpdateUtility-NoVendorID.exe in Windows Vista with WMDC (Windows Mobile Device Center v. 6.0.6873) and the phone in boot loader mode (tri color screen) with working USB cable, with windows firewall disabled and symantec AV disabled as well, RUU keeps saying error 260 "the update utilitiy cannot connect to your pda phone..." .
Do you think I should try this process using XP instead? No matter what i try i keep getting the error 260
Any help would be greatly appreciated

Got it fixed!
it was definately a Vista issue. once i tried it in XP with ActiveSync it worked like a charm and i got my phone back up and running. also used spb backup and restored all my settings.

ipl/spl screen
i got the same problem with new rom wm6, and the 260 eror, my problem is that i have xp and the activesync does`t connect ...
... means i cant redo the original rom ????
PLEAAASEEE HELPPPP !!

Again My phone SPV M600 got stuck at IPL/SPL screen
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.

yekanth said:
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
Click to expand...
Click to collapse
A rom reinstall on xp solved my problems on that one. retry a couple of times! It may not work the first time! hard reset as well...
Try an official wm5 rom just in case
good luck

Can you please gimme step by step procedure
HI Phil,
I am new to these kind of installations . CAn you please Gimme step by step procedure for ROM installation.

mine is now also stuck, after trying to install new rom. wont connect to active sync either, have i fooked it? tried hard reset etc.
thanks

(with a turned off phone, press and hold camera button then insert USB cable)
then flash provider ROM
RECOVERING FROM ERROR IN STEP 8 WM5->WM6
1. Don't panic
2. Don't panic
3. Unplug the phone
4. Reset with stylus,and keep the Camera Button pressed.
5. A 3 color screen will appear(Bootloader Screen)
6. Connect your device with your PC,and run the NVID(no vendor) WM5 rom.
7. The device will be resetted after RUU(rom update utility)finishes
8. Repeat the WM6 upgrade,from STEP 5..
Click to expand...
Click to collapse
from here http://forum.xda-developers.com/showthread.php?t=310452

hi jay
i seen your post in n00b guys one, i fixed it!!!!, thank you so much, i couldnt remember how to get it to those 3 colours.
thanks again
Colin

Hi Iam unable to get the NVID ROM
Hi,
I am unable to get the NVID ROM. The Rapidshare link that has been provided in the other thread is not working. Can some one tell where can i get the ROM.

collywog19 said:
i seen your post ...
Click to expand...
Click to collapse
no problem mate.
..and yekanth i see what u mean about the dead links. i have the files on my computer at home but i'm posting from my prophet right now, so i can't upload. Try using the "pdaviet temp" from one of the wm6 threads?
(http://rapidshare.com/files/54265407/Prophet_PV_Temp.zip)

Hi Iam able to update the Rom but no use
Hi,
To mention my phone is from orange-UK. I got the orange rom from our FTP site and did the flashing/update what ever you say.But still it is getting stuck at the same IPL/SPL screen. Iam very much worried that I will not get a proper solution for my problem.It will be very grate full if some one resolve my problem.

just seems strange...how did you fix it last time? did it just start working again? A random guess would be that the camera button got liquid spilled on it or is stuck in.
If the camera button is pressed in the phone will go to 3 colour screen every time it is turned on.
It won't do any harm if you try to press/move that button to see if u can "unstick" it, not likely I think but u never know...

Help Help Help dead xda2i after attempted rom upgrade

I have an xda 2i which i tried to upgrade rom as the phone was not working correctly with bluetooth phone kit the problem is i tried to upgrade it and i am running windows vista this stopped working and my phone is now dead it connects via cradle but when i try to run rom upgrade using o2 utility i just get an error 101 connection problem is there any way to bring this phone back to life it has a black screen showing usb v1.01 when connected to cradle and serial when not.iwas running windows mobile 2003

peter111964 said:
I have an xda 2i which i tried to upgrade rom as the phone was not working correctly with bluetooth phone kit the problem is i tried to upgrade it and i am running windows vista this stopped working and my phone is now dead it connects via cradle but when i try to run rom upgrade using o2 utility i just get an error 101 connection problem is there any way to bring this phone back to life it has a black screen showing usb v1.01 when connected to cradle and serial when not.iwas running windows mobile 2003
Click to expand...
Click to collapse
WM2003??? XDA 2I? I think you are in the wrong forum my friend... This is for Wizard users. You'll probably get more help in the correct forum here.

dead xda
i am a newbie and maybe running an old version but i am just after a little help possibly one of you flashing junkies could take the time to get me addicted

mfrazzz means that you are in the wrong board. The XDA IIi board is here.

critical problem in jamin for help please

My friend's jamin when he tried upgrading with smart1 wm6
after the flashing process finished it gives the 3 colors of boot loader
the screen flickers continously with the 3 colors
no way to hard reset the device
and activesync doesn't feel it
I searched all the forum for a problem like this but I didn't find any
any suggestion please, or any help?

Flash NVID Rom and try Smart again. Read WM6 upgrade Manuel and readme for the ROM.

NetrunnerAT said:
Flash NVID Rom and try Smart again. Read WM6 upgrade Manuel and readme for the ROM.
Click to expand...
Click to collapse
Please how can i flash with the activesync doesn't notice my device and where's NVID Rom
Ok. I'll search for it but please help how can I flash it to the device which doesn't recognized or felt by PC

If your device is in bootloader mode, activesync cannot recognize it but this is normal. Jamin is recognize only as a usb device and you can downgrade it to NVID rom easly.
Then you could upgrade your favorite rom, I suggest PDAVIET 4.0.0.1
Bye for now

divxmaniak said:
If your device is in bootloader mode, activesync cannot recognize it but this is normal. Jamin is recognize only as a usb device and you can downgrade it to NVID rom easly.
Then you could upgrade your favorite rom, I suggest PDAVIET 4.0.0.1
Bye for now
Click to expand...
Click to collapse
I think I didn't discuss the problem well
The Problem is when I start to flashing a rom a message tells that check if the usb is connected and if the device is connected .
This is happen with the device is connected to the cable and the tricolor screen is flicking . and the device doesn't open doesn't flashing.

must use NVID rom. maybe qtek nvid one from here? http://wiki.xda-developers.com/index.php?pagename=Prophet_ROMs

hasanemara said:
I think I didn't discuss the problem well
The Problem is when I start to flashing a rom a message tells that check if the usb is connected and if the device is connected .
This is happen with the device is connected to the cable and the tricolor screen is flicking . and the device doesn't open doesn't flashing.
Click to expand...
Click to collapse
If the problem still there, Try to release the battery for 1-3 hours and put it again to the device, go to the boot loader and pray. Hopefully it could work. Actually, this way worked on my Himalaya and Prophet.

Just run the "Step 1" component of the PDAViet ROM (http://rapidshare.com/files/32728615/Prophet_PDAViet_Step1.zip), which is just a plain AKU 2.20 NVID. This will find your device even if its in bootloader mode (it doesnt depend on activesync). Just flash it with that sucker and you should have a working phone on WM5, then you can safely upgrade it to WM6 (or leave it if you like).

ekto said:
Just run the "Step 1" component of the PDAViet ROM (http://rapidshare.com/files/32728615/Prophet_PDAViet_Step1.zip), which is just a plain AKU 2.20 NVID. This will find your device even if its in bootloader mode (it doesnt depend on activesync). Just flash it with that sucker and you should have a working phone on WM5, then you can safely upgrade it to WM6 (or leave it if you like).
Click to expand...
Click to collapse
I shall try and tell you the result

error 260 this is the result

i have a slight variation problem like this...
1. i was upgrading my O2 Neo to the latest WM05 & the phone went to bootloader mode & the upgrade started searching for the phone as normal..then some error & it stopped upgrading while the phone was in bootloader mode..
2. at that time,i got an urgent call & had to leave the phone in bootloader mode...
3. when i came back..the phone was dead & now it wont startup at all.. not even in the bootloader mode.
4. Maybe the batteries dead...so i charged it (Over night)..nothing happened in the morning..
5. kept the battery removed for about 5-6hours & still nothing happens..it simply does not startup.
6.I've tried holding the camera button & resetting, but it wont go into bootloader mode.
7. i;ve tried holding the connections button + camera button _ reset but it wont hard reset...
can anyone help me here...
what can i do???

hasanemara said:
error 260 this is the result
Click to expand...
Click to collapse
Error 260... If i remember correctly that's "cant find device" or something.
Few things to check:
Is the PC you are upgrading on running windows vista?
If so, use a different PC running windows XP.
Have you tried a different USB cable?
If not, do so, this tends to be the cause of problems like this.
Have you checked device manager?
Go to control panel, Administrative tools, computer management, device manager and see if you can find your device. If it has a yellow ! icon on it or is listed as "Unknown device" or anything like that then you may need to reinstall the drivers (int hsi case the easiest way to do that is to reinstall activesync). If everyhting is working properly it should show up as "HTC USB Sync", "PocketPC USB Sync" or something like that under the heading "Mobile Devices".
Have you just plain tried another computer, regardless of the OS?
I found that I could never get my phone to flash on my laptop, but it worked without a problem on my desktop. This is not to say laptop's cant do it, it simply means some computers just have problems like (in my case i believe) no USB 2.0, or too low-powered USB ports.

ekto said:
Error 260... If i remember correctly that's "cant find device" or something.
Few things to check:
Is the PC you are upgrading on running windows vista?
If so, use a different PC running windows XP.
Have you tried a different USB cable?
If not, do so, this tends to be the cause of problems like this.
Have you checked device manager?
Go to control panel, Administrative tools, computer management, device manager and see if you can find your device. If it has a yellow ! icon on it or is listed as "Unknown device" or anything like that then you may need to reinstall the drivers (int hsi case the easiest way to do that is to reinstall activesync). If everyhting is working properly it should show up as "HTC USB Sync", "PocketPC USB Sync" or something like that under the heading "Mobile Devices".
Have you just plain tried another computer, regardless of the OS?
I found that I could never get my phone to flash on my laptop, but it worked without a problem on my desktop. This is not to say laptop's cant do it, it simply means some computers just have problems like (in my case i believe) no USB 2.0, or too low-powered USB ports.
Click to expand...
Click to collapse
No I didn't change any and I can connect my o2 xda mini to the same cable
I want to ask few technical question
HOW CAN A SOFTWARE DAMAGE THE DEVICE?
CAN A SOFTWARE FOR EXAMPLE BURNS A PROCESSOR OR SOMETHING LIKE THIS?
If So there will be a big problem with those types of devices
a virus for example can destroy my device's board or processor!!
Yesterday My friend went to an I-mate customer service who tel him that
the board had been destroyed by the bad software !!!!!!!!!
Please Give me technical advice about this problem
and is there a web site for him to buy this board (i-mate jamin)?

I've tried everything... even tried it on my desktop... but my phone just wont turn on now. i've kept the battery removed for more than 8hrs now... i've even charged it for more than 8hrs non-stop..nothing happens..
maybe i should get hold of a charged battery & try it with that battery...?
Any clue how to get my phone started??

got it working !!! PHEW... i used my HP battery which was charged & put it into it..now i've got my bootloader & i'm installing the new OS as we speak... 15% done.... keeping my fingers crossed

done.. got my HP Ipaq battery , which was charged & my new started up in bootloader more.. PHEW !!!
66% done... keeping my fingers crossed

ok, installed...now, one more problem..my touch screen's not working...???
Any idea what to do?
i installed "Prophet_PDAViet_Step1"

Hp 6945 Stuck at Serial and Hp invent logo

Hello Everyone
I need big time help. I just bought Hp 6945 and I tried to update GSM rom from 1.02 to 1.08, while updating it says update fail and try to restart Ipaq and start again. Now My problem is Ipaq just stuck to Hp invent logo. I tried to reset and hard reset and remove battery but notthing work.
I need help
Could some please help me to How to fix this problem?
Thank you

same BS happened to me. the only way to fix it is to load the UK 6915 ROM. thats the ONLY way to fix it. AVOID this update do not try to update the radio. I bricked my phone doing this. STILL looking for a solution. Radio stack is daamged.

where Can I find Uk 6915 rom
Thank you for reply. Where can I found the UK 6915 rom. Is there any instruction to How to load rom?
Thank you

If is FIXEDDDDDDDDDD
Ok
I got it fixed, very simple solution
found it here
http://pdaphonehome.com/forums/hp-h...dowloaded-rom-update-ipaq-dead-need-help.html
Solution:
this is what I did to get this fixed.
1) Get the battery out of the iPaq, and wait for a few minutes while the "serial" image fades away slowly.
2) In the meantime, prepare your cradle, plugged into the AC charger and plugged via USB to your PC.
3) After a few minutes, with the screen of the iPaq completely gray, put the battery and battery cap back on (with our without SIM card), and put it on the cradle immediately.
4) The iPaq should start coming back to life, as if it were being hard reset. Let is stay on the welcome screen (i.e., do not tap it or anything).
5) Restart the upgrade process, it should proceed from there OK
Thank you to origianl solution provider

No network connection
Ok everything work fine, but Now I cann't connect to tmobile. It keep showing me no service.
Any Help please

Ok It is fixed again
There is another update at HP website, which is software update. After installing that everything working fine.

can anyone help? i just bricked my ipaq 6965 too. had already followed those few instructions without any success.. what do you mean by "with or without SIM card"?

After a soft reset, mine's stuck at the initial blue/white boot screen.
Hard reset doesn't work (assuming its call + hang up + power + poke reset).
Ideas?

bring back to life hw6945
i'we tried like you to upgrade radio part and a got an freezed phone
Solution for repair was flashing firmware with this program..
Download-Link #1: http://rapidshare.com/files/96527845/Ipaq_HW69XX_ENG_ROM.zip.html

download files from rapidshare posted by me ,r tested on my phone

hi i have tried to dl the rom asi having the same prob but the file cannot be downloaded. is there any other way to get from you

garyakw said:
hi i have tried to dl the rom asi having the same prob but the file cannot be downloaded. is there any other way to get from you
Click to expand...
Click to collapse
If you are stuck on a HP Invent Screen, with G.39, etc.
And you have tried to hard reset and softreset with no luck, this is what you do.
XP Instructions:
1. Download this link http://www.mediafire.com/?3ygfbx0sjdy
2. In the taskbar area in the right hand corner, right click on activesync, bare with me, I'm using Vista and have to remember this, click connections..., you need to uncheck everything click ok or apply...
3. press ctrl-alt-delete, end process wscescomm.exe, (named something like that, end the process.
4. Extract the file you downloaded if needed.
5. Connect your device to the usb port on your computer.
6. Run Uni Exit Bootloader Application. Done
Vista Instructions:
1. Download these 2 links, and extract them if necessary.
http://www.mediafire.com/?3ygfbx0sjdy
http://www.mediafire.com/?9pmjkponfsg
2. Start Device Manager, (Start-Control Panel, Class View[Far Left Corner])
3. Connect HW6900 to USB port, you should now see a Mobile Devices (Next to + sign), Double Click
4. Right-Click on the Device, Click Update Driver Software, Choose let me pick from a list, Uncheck compatible hardware box.
5. Click have disk, Browse to location where USBAS is extracted, choose the wceusbsh.inf file, Double Click.
6. You should see Microsoft USB Sync, if not and it reverts back to the already installed file, and the box rechecks itself, uncheck it, choose microsoft, and choose the latest Microsoft USB Sync to install
GOOD LUCK

in reference to
Default bring back to life hw6945
i'we tried like you to upgrade radio part and a got an freezed phone
Solution for repair was flashing firmware with this program..
Download-Link #1: http://rapidshare.com/files/96527845...G_ROM.zip.html
its a no go here...

i get error 402.... times out and no can do.... what was that about german language... maybe i just need it spelled out. which screen does the unit need to be in. there is two... monochrome serial vs usb and there is the hp logo blue and white screen frozen indefinitely... please help i love this phone...

Hi, the rapidshare file is missing!
Could you give working link or send me the file to mail, please?

ipaq dude said:
Ok
I got it fixed, very simple solution
found it here
http://pdaphonehome.com/forums/hp-h...dowloaded-rom-update-ipaq-dead-need-help.html
Solution:
this is what I did to get this fixed.
1) Get the battery out of the iPaq, and wait for a few minutes while the "serial" image fades away slowly.
2) In the meantime, prepare your cradle, plugged into the AC charger and plugged via USB to your PC.
3) After a few minutes, with the screen of the iPaq completely gray, put the battery and battery cap back on (with our without SIM card), and put it on the cradle immediately.
4) The iPaq should start coming back to life, as if it were being hard reset. Let is stay on the welcome screen (i.e., do not tap it or anything).
5) Restart the upgrade process, it should proceed from there OK
Thank you to origianl solution provider
Click to expand...
Click to collapse
Man,r u sure the above can work well???? Confusing......I did the above like u indicated,but it's not work on my device HP6915,could u make it in details how u fixed the problem of updating ur device,thanks!
Regards,
Brose

Thanks, This help get me out of freeze
Thanks for posting this link. It brought my hw 6945 back out of the freeze. Stay away from HP's site update. Bad news
johnnynomadic said:
in reference to
Default bring back to life hw6945
i'we tried like you to upgrade radio part and a got an freezed phone
Solution for repair was flashing firmware with this program..
Download-Link #1: http://rapidshare.com/files/96527845...G_ROM.zip.html
its a no go here...
Click to expand...
Click to collapse

Thanks for UNIEXITBOOTLOADER thing, it makes my 6965 rocks again! Btw, could this file be used on other pdaphone such as O2 Atom? Thx b4.

Maybe
Most Likely Yes
bmw2320 said:
Thanks for UNIEXITBOOTLOADER thing, it makes my 6965 rocks again! Btw, could this file be used on other pdaphone such as O2 Atom? Thx b4.
Click to expand...
Click to collapse

cdguider said:
Most Likely Yes
Click to expand...
Click to collapse
I don't think so,Curtis.....But as I know most of dopod device hardly be dead....

I-mate JAM problem, URGENT.. Please help?!

I have a problem with my I-Mate JAM, It loads the OS.. but after everything Installs it converts to the BootLoader screen, and remains unuseable.
If I rest the phone, it loads straight to the Bootloader screen, but if I take off the Battery cover, leave it for a few seconds, then replace it and turn the phone on... It will load the OS setup again, but go back to the BootLoader.
So how can I fix this, and what must I do? Please help me ASAP. The Rom/OS is Windows 2003 SE.
Thanks
Sikuri

try flashing the ROM to a latest windows mobile, i encountered this problem on my HTC Magician, i downloaded the compatible and latest windows mobile for my phone extracted the files on my PC and while my phone is in boot loader mode i connect the USB to pc cable (you'll notice the serial changing to USB) after that i run the update.exe on the files i extracted and just follow instructions on the updater. And now my phone is fix. Hey im not an expert on this, I got thru it by reading the forums here, and there are more experienced experts in here that you can ask. Hope this helps and give you an idea. By the way run the update.exe on a Windows XP machine for it to work perfectly.