Hi, my m600 does not pass bootloader, i can hard reset/soft reset, wm5 has come on once, then went to align screen but had trouble everytime, but at least it was being recognised by active sync to load No Vendor Rom. ( i tried bootmode/then run RUU, with no luck) it either says error 260 no device detected (but its in task bar as removable drive.) or when it was working for them few minutes it it would run No Vendor setup great and recognise (as active sync is working at this point) but doesnt go past 0% and then the error comes up "error 606" and then offers the recovery process. also a little note to add: the first screen when turned on, sometimes the gsm 2.x.x.x is missing?? from the top left corner.
any help would be appreciated.
Related
I have a Dopod 818pro that was flashed with the wrong ROM and now all I get to is the DOPOD splash screen. I can get to the TRI color screen by pushing the camera and power button.
I have tried hard reset but seems the OS is missing from the phone.
I have the original ROM for my phone on my PC but can not use active sync as the phone does not go further than the SPLASH screen.
How can I reload my original ROM using the SD card.
Any help would be appreciated.
Thanks
Canada59
use the tricolor screen even though active sync doesnt see it it still flashes but u need to use the flash upgrade wizard and not the cli interface one
Worked for me but i cant sae it will work 100%
Where do I find the flash upgrade wizard?
When I plug usb in, i get usb on the white band in the color screen
Tried to run the update using RUU and get ERROR 260
Thanks for your help in this
Yeah RUU same thing i was meaning that one cause theres another that uses cli but its a bit dodgy
RUU Wizard should work it never detected ma G4 but it flashed it anyway i was well chuffed cause i thought i had bricked it
I just tryed the app without the phone connected and it gave me error 260 so maybe try different cable or pc cause i had a issue with xp not detecting my phone and i had to reinstall xp just to get active sync to work properly
The main problem is that I had a bad flash, now I can not get pass bootloader screen, PC does not see device, active sync says not connected. there must be a method for loading the NK.ntf file from sd
Not came across anything like that as the SD card driver would be loaded at boot with the OS and in your case theres no OS booting it would be hard to sae it can be done but i bet someone will prove me wrong lol
Good Luck mate ill keep an eye out for anything like that though
Thanks for the help....phone is useless at the moment......
Hi
I have a Dopod with the following symptoms
It starts up and gets hung in the Dopod flash screen. Just hangs there and does nothing
It can be soft booted into bootloader ver 1.09
Can be hard reset - gets grey screen - press R on keyboard then space and it takes you back to splach Dopod screen fine
Tried to update to SP7 But gets com error 260 and wont go any further
Tried several ROMS and gets to load screen 1% then gets comm error 260 etc
Driving me mad - it should be salvageable but I cant seem to get it correct
Please help if you have ideas
Kind regards
John
Hi
Ok did some more reading and fixed it by reloading the original early ROM and going from there
All good now!!
John
Dear All, finally I bricked my artemis
Today I can't remember what went wrong when I tried to update (for the 5th or 6th time) the
rom, but it crashed.
BootLoader:
IPL 1.12.0001
(RUU in the top right corner)
SPL 1.12.0000
USB
When I try to upload the ine that worked long time ago:
RUU_Artemis_TMO_PL_3.15.118.1_4.1.13.50_03.06.90_Ship i got error 294 (invalid vender id).
After reset i got it stucked on boot screen:
IPL 1.12.0001
SPL 1.12.0000
GSM 02.67.90
OS 1.12.0.0
Hard reset doesn't help - same thing.
One more time entering bootloader, plugging usb, and trying:
RUU_Artemis_TMO_PL_3.15.118.1_4.1.13.50_03.06.90_Ship - it goes to the process bar and... hmm
stuck - earlier i got connection error after 2%, now i got 0% and after few seconds error 262
(update error), than I did recovery steps, and the device restarted and entered in bootloader
mode. After second the screen went pink, and than it hanged.
Let's try one more time - enetering bootloader mode, plugging usb - not connected (there is
no usb on scren). Unplugging, plugging again, vista still don't want to cooperate.
Unplugging, resetting device - it doesnt. removing battery, entering bootloader, plugging
usb, doesn't work. unplugging, soft reseting - it goes in bootloader mode (!?), the screen
ligths up and than goes blank. reseting in bootloader, the buttons lighted, vibra scrathed 3
times and it went blank again. Trying to enter bootloader once again, the bootrloader shows,
than goes blank. Removing battery, entering bootloader mode - i'm in , plugging usb -
nothing changes i can not connect.
Ooops, I can't woke up my Artemis now
Removing battery helped, but when it resterted it went to bootloader mode :O When trying to
upload new rom (HTC_1.12.405.01_026790_WWE_SHIP) on third screen that veryfies information on
pda, i got VISTA BLUE SCREEN YEAH!
After system reset i had multipy problems with usb conneciotn that I mention aobve, but
finally I catched the connecion - this time my uploading progress bar went to 2% and no more. Error 294 said that i have invalid vender ID.
Does anyone have any solution? I cannot use Artemis_UPSL because I cannt Sync with my phone, so - which ROM could be same as my Vendor?
PLssss help!!!
Sorry for my language - i'm tired and sad
HELP!
Working on my Artemis again I thought that maybe the battery was not full...
Now, trying to upload WM5_PL_OS_1.38.0.0_Radio_2.95.90_pl_orange (the one that I think is my primary rom), but after 3% i got error 270 (update error, the image file is corrupted). Hmmm.
When I'm trying to enter to bootloader with usb connected the screen goes blank. When I unplug usb it goes in bootloader mode with no problem. After plugging usb everything seems to be ok but it's not (the usb word is on the screen, but the uploader can not connect (error 260). Hmm
Now I can not sync
Ok, I got it. To sync i gotta remove wsb, remove battery for about 3 sec, plug it again, turn device on, and than enter to bootloader. That's something.
Hello together
wish you nice eavening!
My Problem is the following: The only thing, on my htc touch hd T8282 that seems to work, is the bootloader.
Til five minutes ago I could read there:
BLAC 100 32M
SPL-1.54.0000
MicroP - BlackStone (LED) v6
now the following is added:
in the right, top corner: RUUNBH
in the green field: Upgrade ROM code error, Please try again
I think, this is because, in my helplessness, I interrupted the flashing process. But that's not the main problem.
Beside that, I can "start" the phone only by plugging in the USB cable from Computer or charging station. Then the phone vibrates, and the "smart mobility" screen comes up. After about 5 seconds it starts again, doing the same.
I tried hard resets, but it doesn't work. The only reason why I'm still trying to repair the phone is, that the bootloader is working. To me a signal, that somhow not everything is lost, but maybe I'm wrong.
I tried to flash the phone too. I tried first with the official "BlackStone_GER_1.56.407.2_Radio_52.60.25.33_1.12. 25.16DE_Ship.exe" which worked in the bootloader mode. At least the screen "flashing was sucsessful" showed. The bootloader was the same and nothing changed.
After that I tried with "HSPLWrapper_Blackstone_156OliNex.exe", which is not working. It demands a connection with the ActiveSync, which I have on my Computer, but the only way the computer detectes the Phone is in the bootloader mode. In normal mode computer and active sync don't detect a phone.
So my questions to you:
Do you know a way to load the hard spl (from OliNex) to the phone, although I cannot connect it to ActiveSync? There should be one, because with the official data it "works" (or seems to).
Do you have any help?
Thankyou
Samuel ben jamin said:
Hello together
wish you nice eavening!
My Problem is the following: The only thing, on my htc touch hd T8282 that seems to work, is the bootloader.
Til five minutes ago I could read there:
BLAC 100 32M
SPL-1.54.0000
MicroP - BlackStone (LED) v6
now the following is added:
in the right, top corner: RUUNBH
in the green field: Upgrade ROM code error, Please try again
I think, this is because, in my helplessness, I interrupted the flashing process. But that's not the main problem.
Beside that, I can "start" the phone only by plugging in the USB cable from Computer or charging station. Then the phone vibrates, and the "smart mobility" screen comes up. After about 5 seconds it starts again, doing the same.
I tried hard resets, but it doesn't work. The only reason why I'm still trying to repair the phone is, that the bootloader is working. To me a signal, that somhow not everything is lost, but maybe I'm wrong.
I tried to flash the phone too. I tried first with the official "BlackStone_GER_1.56.407.2_Radio_52.60.25.33_1.12. 25.16DE_Ship.exe" which worked in the bootloader mode. At least the screen "flashing was sucsessful" showed. The bootloader was the same and nothing changed.
After that I tried with "HSPLWrapper_Blackstone_156OliNex.exe", which is not working. It demands a connection with the ActiveSync, which I have on my Computer, but the only way the computer detectes the Phone is in the bootloader mode. In normal mode computer and active sync don't detect a phone.
So my questions to you:
Do you know a way to load the hard spl (from OliNex) to the phone, although I cannot connect it to ActiveSync? There should be one, because with the official data it "works" (or seems to).
Do you have any help?
Thankyou
Click to expand...
Click to collapse
wel its saying spl so its original spl and not hspl
if you downloaded the german rom form the xda site it doesnt work as the spl in that rom isnt for youre device
if youre in bootloader try to flash hspl on it and then you can flash roms from the site
the other option is got to htc official site and look up the blackstone
there search the latest rom
if you want to download it you have to enter youre imei(can be found under the battery) with that code the rom youre going to download is only for oure device and is supposed to work for you
hope it helps
Thankyou for writing!
I downloaded and tested the rom from the htc site. I can run that and it comes up with the "successful screen". Then, the phone restarts, and I have the old problem, nothing changed.
As I mentioned before, I can not flash the hard spl from OliNex. That's my big problem. Because, also mentioned before, my phone is not recognized by the active-sync programm and in bootloader mode the HSPLWrapper from OliNex doesn't work.
hope there are some more replies and answers..
Samuel ben jamin said:
Thankyou for writing!
I downloaded and tested the rom from the htc site. I can run that and it comes up with the "successful screen". Then, the phone restarts, and I have the old problem, nothing changed.
As I mentioned before, I can not flash the hard spl from OliNex. That's my big problem. Because, also mentioned before, my phone is not recognized by the active-sync programm and in bootloader mode the HSPLWrapper from OliNex doesn't work.
hope there are some more replies and answers..
Click to expand...
Click to collapse
In activesync (or windows mobile device centre) go to connection settings and make sure that "allow usb connections" is ticked. Then retry connection device to computer. Put device into bootloader while connected. Does bottom of bootloader change from "serial" to "usb" after a couple of seconds?
In activesync "allow USB-connections" is ticked.
In the white, bottom part of the bootloader is written "USB" when connected to Computer. But if I connect it to the charging unit and start in bootloader, the white field is empty. I can't start it without any electricity source. Either there is another problem with the battery or, because you can't turn it off, the battery is flat all the time.
Also, the original htc blackstone rom-program, detects a connection to the phone, and is loading the rom properly, it seems. Because I could turn the bootloader screen back to where I already was once (by loading the official rom again):
BLAC 100 32M
SPL-1.54.0000
MicroP - BlackStone (LED) v6
Somehow it seems, that the power button is not working, I can't shut down when it is in bootloader, and can't really start the unit. But it's hard to say, 'cause it's starting automatically.
thanks
I get so far with running Hard SPL V7 but it ends up with the 3 colour bands on my phone (plus white) while running RUUWrapper.exe from a pc.
I then get the error
"ERROR [[260]] : CONNECTION
This error occurs when there is an “open port error” before upgrading the CE ROM image.
Solution: You can reset the device and run RUU again. If you still encounter an “OPEN PORT ERROR” again, reset your computer and try again. "
I've followed the advice here and tried again but nothing seems to do any good. The phone disconnects from Active Sync everytime.
Is there something else I can try?
I've continued with this but still get the connection problem no matter what I do. The advice for the 260 error seems more in hope than expectation. Surely just doing something that doesn't work again and again is a definition of madness??
Success.. I don't know exactly how I managed to do it but eventually I installed a Windows 6.5 ROM by MrDSL which is a major improvement on the old Orange installation...