Screen alignment or touch screen replacement ? - 8525, TyTN, MDA Vario II, JasJam General

Hi..
I bought a Vodafone V1605 ( HTC Tytn ) from ebay... the auction description indicated some alignment problems that could be resolved by screen re-alignment...
But when i got the package i found that the problem is worse than that... as you can see in the picture ( http://img81.imageshack.us/img81/4319/tytnscreenul8.jpg ) the top-right of the screen seems to be with problems.... I tries to draw several horizontal lines... and in the top-right part of the screen i got some waves...
I'm thinking about returning the phone... but can this be resolved by purchasing a new touch-screen ? I've seen that buying a replacing touch-screen is not very expensive....
Best regards,

A new touch screen might help. What also is a known issue is the screws at the back of the screen. Try to tighten these it helped for some guys allready.

I replaced my touch screen after i cracked it and now i can't get it to align at all.
I click anywhere on the screen and it thinks it's a click in the top left of the screen as the start menu opens up.
Haven't been able to find anyone to answer my posts for help either.

If there is dirt on the edges of the screen (between screen and cover) it can cause alignment problems as well. I had to recalibrate mine several times a day at some point as dirt would move and press different locations, biasing the digitizer. I got tired of it, dismantled the phone, took the LCD out, cleaned it as well as the inside of the case, and put it back together. No more issues so far.

kilrah said:
If there is dirt on the edges of the screen (between screen and cover) it can cause alignment problems as well. I had to recalibrate mine several times a day at some point as dirt would move and press different locations, biasing the digitizer. I got tired of it, dismantled the phone, took the LCD out, cleaned it as well as the inside of the case, and put it back together. No more issues so far.
Click to expand...
Click to collapse
Had exactly the same problem (and solution) for the screen alignment problem of my Xperia X1. I removed a tiny plastic piece (most likely a leftover from production process) which stuck between the metal frame and the touch screen. After that I could easily align the touch screen and have no alignment problems anymore.
Be careful to not break the screen - I used a thin sewing needle and tweezers to remove the plastic piece.

Related

Touch screen stopped working :-(((

Hi,
The touch screen part of my universal has ground to halt to the point that it won't work.
There doesn't appear to be any cracking and I don't recall dropping it or sitting on it.
I work a fair bit outside and can get quite a bit of dust and dirt in my pockets and am wondering if it could be due to dirt getting into the connect on the hinge.
Has any one else come across problems with the hinge?
I'm reasonably adept with a screwdriver - are there any things to watch out for when disassembling to check it over?
Hi..
If u can open with the Universal guide posted in the forum then try clean ing the connectors on the Right and Left of the Clamp Shell part with Iso Propyl Alcohol.
Before opeining you can try pressing mildly with yr fingers, at all the forur corners..it can start working..else do the above...
Hi,
OK, the screen seems to be working OK this morning, however I seem to be getting a sort of ghost effect where it appears as though the phone icon and the volume icons are getting pressed resulting in the volume controls and the phone/flight mode popup appearing on screen.
I guess it is all down to dirty connections.
Do you have a link to the thread about dismantling the hinge, I can't seem to find it.
Thanks.
re isopropal alchol
only use 99% alchol to clean contacts anything below that can cause corrosion on printed circut boards and contacts.
any progress yet.
mine stopped working today too.
but when i took off my screen protector, it worked for a while.. now its dead again.
I think the screen protectors may cause this problem, as I too had this problem with a screen protector; but when i took it off it would work and and off. I cleaned the screen up and after a few hours my screen was working again!
being in Australia I go to the beach allot. with my jasjar.
the sand gets stuck in the sides of the screen putting pressure on the screen and disabling any input. just a thought that it could be the same with u.
hope u sort it out, otherwise claim it on warrenty sooner than later.
The problem I have with the screen is that occasionally the touch screen side of things appears to stop working and also the the volume, wifi and phone dialogs keep on appearing as if I am pressing the relevant icons in the top bar.
I'm guessing some dirt has got into it somewhere or there is a loose connection, but am struggling to open up the screen's case to inspect it.
6680abhi said:
I think the screen protectors may cause this problem, as I too had this problem with a screen protector; but when i took it off it would work and and off. I cleaned the screen up and after a few hours my screen was working again!
Click to expand...
Click to collapse
i took off my screen protector and it worked an hour...
got home, prepared to go to the T-mobile store.. then cleaned my screen ( without protector ) with a small cloth and it was working again.. so weird..
lets wait and see what happens ..
It's not really that weird: If some dust, or something equally small gets between the screen and the plastic frame, it can put enough pressure on the screen, and so the touch screen takes it as a constant (or intermitent) input, invalidating any other action on the rest of the screen.
I just received my Aquapac waterproof (and sand/dustproof) to use my Jasjar hapilly in the beach! :lol:
oh so annoying, my volume sliders keep popping up now..., as if some one keeps tapping, cause when not in Land scape mode when i open the "START" menu. it scrolls down, the same input/tap as wher the volume is in Landscape mode
There must be something wrong ... my screen still isnt working properly
one possible solution for touch screen not working
guys.... although I dont need to register onto this portal and it took me 15 minutes to register (fault of my own) but I got so much relieved with the solution that it deserved 15 minutes of my effort ;-) I hope it helps someone...just like it did help me....
I own a P835 Asus mobile and from past 2-3 days was having problems - start menu continuously appearing and my taps not getting recognized. Since yesterday my screen suddenly stopped responding to any taps or scrolls altogether.... buttons were working fine but not the screen..... i spoke to the facilities centre this morning and was about to take it to the shop but due to my laziness...didn;t go.....
Thanks guys.... what you mentioned above is very correct.... it was just a tiny molecule of dust that the screen was interpreting as my input and finally refusing all my taps..... I just cleaned the screen and the speaker side with the mere stylus n things started working.... thanks a lot.... more than laziness was this worry cause I just bought this piece a month before....
so people...before takin it to the shop....try this one too.....huhhh.....

How to replace the digitizer.

I cracked my aria screen pretty much right after I got it, Managed to get my hands on a new digitizer and replaced it. I found a quick walkthrough on Android forums. It helped but had a few points that could have been more succinct.
Posting here in case anyone needs.
Took me about an 1hr 30min the first time trying to figure it out on my own.
My additional comments are indicated by **.
I put some addendums to @Jcawesome's steps...
( http://androidforums.com/1211507-post42.html )
1. Remove backcover
2. Remove Battery, sim chip, and memory card
3. Unscrew the top two screws (meaning the end farthest from the memory card.)
4. Using a flat plastic wedge, (I used the one that came from my ebay order, it looks like the blue tool in this pic )
5. Carefully pull off the parts at the top being very cautious not to break anything. (Do not pull the circuit board out, only lift the end closest to the edge of the phone)
** there are two pieces to pull off....with the phone laying flat (screen down and the top facing away from you) a larger yellow piece with an attached back speaker comes out towards you. a second piece pulls up (north as if on a map)... but becareful because there is a bunch of tape and tackiness all throughout this thing (literally I felt it was held together by tape). I actually pulled off the grill on front as well.
** the circuit board is kept attached near the top right. the element that is the power button snaps off. (there are two little dots just to the right of the speaker with what looks like blackish tape that connects to the circuit board... you can pop this off.
With that off, I could lift the circuit board about 30 degrees or so... I wasn't comfortable pulling it back any farther than that.
I did step 5 AFTER I got the screen off.
6. Using the flat plastic wedge again, push the wedge tool between the phone and the broken screen. (It will feel like you are breaking it but it is fine, it is held on by a sticky paste that will slowly give way)
** careful on this part... especially difficult depending on how your screen is cracked. but it is just a bunch of sticky tape that is keeping it attached.... I had to peel away the goo and connection near the top sensitive areas as my ear piece speaker came off with the goo.
7. Disconnect the connecter from the old digitizer to the new one and remove the old digitizer.
**I used a small little tweezer and sneaked it in underneath the circuit board to pull the digitizer connection out.... a little difficult to push back in, but just took some patience.
8. Being careful not to put fingerprints on any exposed surface of either the phone lcd or the replace screen, place the new digitizer in the exact spot of the old one.
** have some lint free microfiber cloth handy and perhaps some screen cleaner.... I spent about 15 minutes cleaning the lcd screen before laying the replacement digitizer back on.
I actually did step 9 before step 8.
9. Connect the connecter from the new digitizer to the board, be careful not to pull the circuit board out and do not scratch the board.
10. You may want to use some glue to hold the new screen on, hopefully this will not happen again. My phone still had enough of the sticky paste left to hold the new screen fine.
** I agree... the first time you replace it will be fine.... afterwards tho, I can see it running out of tackiness.....
11. Put the phone back together in reverse order.
12. Turn it one and everything should be working again.
** in a nut shell
1) take out two screws
2) detach two yellow shell pieces
3) unhook a latch that is the power button
4) pry off the screen
5) lift the circuit board approx 30 degrees.
6) detach digitizer connection from underneath using tweezer
7) replace digitizer connection, return circuit board flat
8)position digitizer and press down to adhere
9)replace two plastic yellow shell pieces
10) screw it back together
done.
let me know if you have any questions.=)
enjoy your "brand" new aria.
dude,, this is a PITA,, I did,, was about 1hour, the hardest part,, is to not put the fingers on the LCD and cleaning the new screen..... dust particles everywhere... and at the end still got one...
Sorry eortizr, If I made it seem easier than it was. I spent quite a while cleaning the lcd screen when I replaced the digitizer... I don't think it's possible to change the digitizer without getting fingerprints on it though. But with some diligence and working in a clean area, I was able to keep all dust and finger prints out of the final product.
My wife dropped hers. Cracked up pretty good but still functional. Think I might just go ahead and pay the $100 and have someone who does it for a living do it.
I can totally see me trying DIY concentrating real hard dripping sweat all over it and ruining the MB. LOL
Replaced the screen today. Half way in I thought I definitely bit off more than I could chew. I got it done though. A couple of things I learned:
The digitizer unplugs away from you or toward the screen with the phone laying flat (screen down and the top facing away from you). I kept thinking i had to unplug it by pulling it north, toward the top of the phone.
I dropped and threw away both the front speaker and the very small rubber piece that covers the proximity sensor so... when I turned the phone on everything looked good, until I answered my phone. The screen went blank and I couldn't hear anything. I found the speaker and the proximity sensor cover and replaced them.
I would do it again, its worth saving $50 or so.
Thanks for the tutorial dreamflux.
I found the whole kit including the adhesive here: http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=180643624141
This is the seller in case the sale ends and the link breaks: http://myworld.ebay.com/chinaphoneaccessories/?_trksid=p4340.l2559
I found a replacement digitizer from tmart dot com for $55, free shipping. Just search Aria on their site, you'll find it. Sorry, I can't seem to post links yet.
What was peculiar, was that it has only the HTC logo in the center, and no ATT logo. Looks nice and clean. They included plastic separator tools and torx drivers, though nothing in this phone uses torx. The site is a little shady, and while their headquartered in Hong Kong, it shipped from Brooklyn NY about 5 days after purchase, priority mail. The swap wasn't bad, but my only complaint is that the lights from the softkeys seem to shine up onto the screen, but you get used to it. It's probably because I didn't transfer the stickers over on the bottom of the digitizer.
Thanks for the directions ... I just replaced my digitizer. I had 2 major problems: 1) my power button doesn't work any longer (I'm going to take it apart and try to put it back together and see if that fixes it), and 2) you HAVE to use BLACK sticky stuff to seat the bottom of the digitizer - I used the clear stuff that came with the digitizer, and now I have tons of light bleeding into the LCD from the button backlights. I'm not sure what to do about the bleed ... I guess I'll have to tear it down again and put black stuff in ... damn.
That's the deal with that excess backlighting! I thought it was just a matter of the screen being misaligned. Terrible that I have to replace that black foam, it got shredded while I was dismantling the thing to replace the digitizer.
eortizr said:
dude,, this is a PITA,, I did,, was about 1hour, the hardest part,, is to not put the fingers on the LCD and cleaning the new screen..... dust particles everywhere... and at the end still got one...
Click to expand...
Click to collapse
its always suggested to work in a dust-free space but we all know that's virtually impossible.
I had a bit of fun with dust & fingerprints when replacing my LCD after getting my Aria, After a time or two of taking apart and being unsuccessful, I left it as is with one visible flake.
If you take a hot shower the steam in the air sticks to dust particles leaving no dust
Sent from my Liberty using XDA App
aria
use electrical tape to cover up the lighting that comes through the digitizer
use 3m double sided tape to hold digitizer to lcd
use rubber gloves to change screen to not get finger prints on it
dust906 said:
use electrical tape to cover up the lighting that comes through the digitizer
use 3m double sided tape to hold digitizer to lcd
use rubber gloves to change screen to not get finger prints on it
Click to expand...
Click to collapse
*Just to make sure I'm putting the electrical tape on correctly*
put the double sided tape on and then put the electrical tap (sticky side facing up) on top of the ds tape then apply the screen to the lcd
Thanks for the explanation dreamflux.. This, along with some youtube videos helped me out to change the digitizer, but patience is THE key...
Brought my phone with me to Cedar Point the other day. Survived the entire day....until I stopped at the bars on the way home. Got out of the car, forgetting I had my phone on my lap---shattered right by the track pad.
Just got my digitizer today for $22 on ebay (not bad) After 2 hours and a migraine later, everything came out great.
The only 2 things wrong now are the light from the softkeys bleeding onto the screen and out the sides (I'm just going to shut those lights off), and the trackpad sits a little lower than the screen now. Either I didn't align it right, or the glue isn't holding well. It's weird, if you press on the glass anound the trackpad, it wakes the phone (cm7 trackpad wake).
I only plan on using the phone for a few more months, so I'm happy with the results.
Uhhggg, did the replacement on my son's Aria. It wasn't so bad, but now the LCD screen doesn't light.
I get the vibration when you first hit the power button. Is this correct? I'm not too familiar with the phone.
Rececked the connector for the LCD and it seems to be snapped in.
brivette007 said:
Brought my phone with me to Cedar Point the other day. Survived the entire day....until I stopped at the bars on the way home. Got out of the car, forgetting I had my phone on my lap---shattered right by the track pad.
Just got my digitizer today for $22 on ebay (not bad) After 2 hours and a migraine later, everything came out great.
The only 2 things wrong now are the light from the softkeys bleeding onto the screen and out the sides (I'm just going to shut those lights off), and the trackpad sits a little lower than the screen now. Either I didn't align it right, or the glue isn't holding well. It's weird, if you press on the glass anound the trackpad, it wakes the phone (cm7 trackpad wake).
I only plan on using the phone for a few more months, so I'm happy with the results.
Click to expand...
Click to collapse
did you have any problems with the digitizer responsivenes or something like that? I'm need one and curious about the quality of the cheap digitizers in ebay.
so I replaced my friends screen and now the phone turns on, has sound, vibrates, but just doesnt turn the screen on... the light sensor works and all, and if I call it, it rings and everything, just the screen won't turn on it stays black... I've checked the 2 ribbons and everything is fine, anyone have a suggestion..??
jdmsohc22 said:
so I replaced my friends screen and now the phone turns on, has sound, vibrates, but just doesnt turn the screen on... the light sensor works and all, and if I call it, it rings and everything, just the screen won't turn on it stays black... I've checked the 2 ribbons and everything is fine, anyone have a suggestion..??
Click to expand...
Click to collapse
so what I meant was the digitizer turns on, but it is just a dark lit screen, no visual anything going on.. If i call it from another phone it will ring, but when i swipe right to left to answer and press around where the answer button is it doesn't respond either, just rings and rings... anyways just wanted to elaborate a little more..
---------- Post added at 02:28 AM ---------- Previous post was at 02:08 AM ----------
msailer said:
Uhhggg, did the replacement on my son's Aria. It wasn't so bad, but now the LCD screen doesn't light.
I get the vibration when you first hit the power button. Is this correct? I'm not too familiar with the phone.
Rececked the connector for the LCD and it seems to be snapped in.
Click to expand...
Click to collapse
same thing is happening with me as well..
^^^^ Soooooo.....I got the same thing on my wife phone, the BLACK SCREEN. I did my homework and read and watched videos on how to replace the digitizer. I was in a steamy room with all my tools from work with pre-cut electrical and .005" double sticky tape. im a mechanical assembler. I did everything to the tee and was very carefull. i think i got a bunk one from china. I bought mine for $19 from china. It had at&t logo and everything. you get what you pay for? So I've got to pay now $50 for a replacement phone through ins. Not bad because before i made the claim i thought the replacement was $150. Anyways just a heads up. Now i got a phone of spare parts Whats cool is that i get to root her phone all over again. So if anyone here has had the black screen. let me know what happened next with your situation. Did you fix it? replaced it with another one? thanks

LCD & digitizer problem

This is my first post here and though i read similar posts on this subject i would
like to read your opinions on this one.
I accidentally dropped some water on my touch hd and my display got damaged.The phone worked fine and so did the digitizer but the problem was that the backlight of the display was dead.At some point the backlight turned on but when i tried to input the unlock code it turned off right away (did this several times).I knew that i should replace the lcd (and the digitizer just in case).
I bought the lcd and the digitizer seperately and i managed to assemble the phone back using the service manual.Since then when i turn the phone on I hear the starting sound,i get the vibration then after a while the screen with no backlight again displays the "tap here to configure your phone" screen (after the hard reset),when i tap i get no response.
I checked the connections many times and i also used a second digitizer with no success.
Is there a possibility flashing a new ROM will solve the problem?
If so is there a way of flashing a ROM when the phone's screen is not usable?
Waiting for your precious opinions/suggestions/knowledge
Thanks in advance.
Hello,
Flashing the ROM won't solve an obviously hardware problem.
If you changed the LCD and still have no backlight, then either you bought a defective screen, or the problem is elsewhere, maybe on the main electronic board... Which would be bad news.
BTW, I wanted to change the digitizer in the apst years, but its not provided with the glue, so I had to buy a whole assembled screen + digitizer.
How did you manage to glue the digitizer on the screen ?
I aligned the screen with the digitizer and then i used small pieces of a special thin and trasparent tape to hold it in place.The tape holds the screen tight and it is barely visible, it also has the advantage that you can seperate the lcd and digitizer anytime you want with ease (though you have to be very delicate when applying it to get a good result)
I asked for a replacement of the defective lcd and i hope i will get a new one.

Tattoo: digitizer (touch screen) broken for the 2nd time

Hello there,
I bought my Tattoo in January this year. It went to the service centre once already, because the touch screen did not work anymore. It came back with a new one.
Today it got broken again. The symptoms; it was getting more and more difficult to get a long press, for instance to move an icon or remove a widget from the desktop. After it stopped working, I could see a dot matrix on the screen, and when the screen is off, it looks like there is some oil, diffracting the light, a bit like a rainbow.
Am I the only unlucky Tattoo owner with this kind of recursive issue? Is the life span of a Tattoo digitizer only 4 months?
What about capacitive screens - are they less fragile?
Is there any particular Android phone with a good / strong build and quality reputation?
Cheers,
JPascal.
I have similar problems with the screen. It's hardly usable. I get those rainbow-like spots on the screen, there is a big white mark at the top of the screen that fortunately I can see through when screen is on. Also the screen sometimes thinks I've pressed in places where I haven't, so it's impossible to use until I reboot. There are many other problems, and the only reason why I don't send it back to get fixed is that they keep it for weeks, and I need it.
I live in Taiwan, Taipei, so HTC support / service is not bad here. They can come and pick my cellphone at my office, and I can hope to get it back 3 days after.
I'll ask them if it's a common problem, will update this thread later.
JPascal.
_david_94 said:
I have similar problems with the screen. It's hardly usable. I get those rainbow-like spots on the screen, there is a big white mark at the top of the screen that fortunately I can see through when screen is on. Also the screen sometimes thinks I've pressed in places where I haven't, so it's impossible to use until I reboot. There are many other problems, and the only reason why I don't send it back to get fixed is that they keep it for weeks, and I need it.
Click to expand...
Click to collapse
I had same problems with digitizer.. But I fixed it :] This can happen when the screen is pressed for a longtime in pocket or the phone is dropped. But I fixed it :]
I turned the phone off, removed mask and tried to lift up digitizer little bit on side where was rainbow-like spots. When they gone, I put digitizer down and press on the side that I lifted up. Now everithing works like a charm
Yeh I have one of the rainbow spots..too i wanna know how can it be removed....cause i cant get rid of it.
that oil spot or Newton ring can be easily fixed by removing top mask and inserting sharp object between LCD and digitizer couple millimeters and then pull the digitizer up so it detaches LCD and newton ring disapears, then while you removing sharp object, used to pull digitizer up, press with finger from center outwards to pump out air and place it back firmly .. I`ve successfully fixed two HTC tattoo`s and one HTC HD display with that technique ....
najzlijiji
Nisam najbolje razumeo sta je digitajzer i proces uklanjanja mrlje na ekranu, pa ako mozes odjesni mi na srpskom, poz!!!
http://forum.xda-developers.com/showpost.php?p=4894288&postcount=8

LCD problems! HELP!!!

I replaced my digitizer recently and when I put the phone back together and turned it on, the LCD looked different any thoughts or suggestions. I looked through some other threads but nothing described look like the problem I am having.
I guess the digitizer isn't original and polarizes the light in a different way, giving the strange optical effect.
Another issue maybe the digitizer is stuck tightly against LCD, try to put between the two a strip of thick adhesive tape around the edges, avoiding tight contact.
Or worst, maybe you damaged the LCD while disassembling, to verify this lift the digitizer and see if it looks the same or not without digitizer.
It looks as though it is a similar problem to * HERE *
I you go into your Web-browser and press the menu button, then view page info.
Look at the background (the webpage). What are the colours like?

Categories

Resources