Database Users

bricked my vogue

i used imcokemans unlocker (which i have done before) and blee0125's kitchen and really screwed up somewhere!
i cant get it past the "htc smart mobility" screen. it comes up, tells me the driver and radio versions, then those disappear like they are supposed to and...nothing else.
any suggestions would be great, plz im dying here!
i have tried hard and soft resetting and...nothing!
THANKS.
EDIT: just for those coming to this ancient and recently revived thread, this (my) problem has been solved. altho there are other people now with similar problems

Have you tried re-flashing?

jim256 said:
i used imcokemans unlocker (which i have done before) and blee0125's kitchen and really screwed up somewhere!
i cant get it past the "htc smart mobility" screen!! it comes up, tells me the driver and radio versions, then those disappear like they are supposed to and...nothing else.
can anybody help me???? PLZ im dying here!
i have tried hard and soft resetting and...nothing!
THANKS.
Click to expand...
Click to collapse
Do a camera power reset and try again.

i tried that and it didnt do anything at all. isnt that just where you hold the end key and the side camera key and stick the stylus into the hole?
if so, it have any different effect than the standard soft reset

AraqirG said:
Have you tried re-flashing?
Click to expand...
Click to collapse
and i did try...sort of. im not sure how to seeing as how i can never make it past the boot screen, and therefore cannot connect it to activesync.
THANKS.

jim256 said:
and i did try...sort of. im not sure how to seeing as how i can never make it past the boot screen, and therefore cannot connect it to activesync.
THANKS.
Click to expand...
Click to collapse
Hold down the power button and the camera button at the same time until the tri colored bootloader comes up. If that works, try flashing the stock rom for your carrier.
If that doesn't work try the same steps with the memory card removed.
If that doesn't work try to do a hard reset and see if that will take you to the bootloader.
Also, what are the numbers in on the bootloader...are you sure your device is unlocked? I believe it should say... SPL-00.40.coke... on the 2nd line if your unlocked.

You shouldn't need to connect to activesync to reboot. After you run ImCokeMan's unlocker you should be unlocked until you run it again.
As I said in the last post, all you have to do to get to the boot loader is hold down the power and camera buttons at the same time. This will put the phone into the boot loader and you should be able to flash back to the stock rom and start over.
It kind of sounds like you relocked the phone and then tried to boot a custom rom.

sorry i wasnt saying i needed to connect to activesync to reboot, i was saying i needed to connect to activesync to flash, and it wouldnt boot up so i couldnt get to activesync.
and i did to imcokemans unlocker, and everything went fine. when i was setting up the device (ie. setting password, time zone, calibration, etc...) i just decided that i didnt need to finish that as i was intending on flashing a custom rom anyway, and so any settings i put up the time to set would be erased.
having said that, i went ahead and starting flashing a custom rom right from the wm welcome screen that you get on a first boot.
thanks a LOT for your help, promptness, and attention

So are you back up and running?

well, now i am. i just took a 30 min drive down to the sprint store and got a replacement :S
thanks a lot for your help though, im scared i may really need to refer back to this thread later. but if i do, at least i know i should be able to fix it!
thanks.

well, i just did it again. i must be doing something wrong in the cooking of my ROMs...about to try out your solution..hope it works!!
wish me luck :S :S :S :S

well i was able to re-flash, but, unfortunately, it is stuck in the same "htc smart mobility" screen again. i think i have been able to narrow it down to the oemizer app. i must be doing something wrong in there.
oemizer http://forum.ppcgeeks.com/showthread.php?p=100746&referrerid=10115
ill keep cooking and trying tonight until i find what it is the problem is i guess, thx for your help guys. especially you 360discgolf.

well, after cooking and flashing too many times to remember this late, all i can do is ask for help when you guys wake up and check this thread.
in the last couple of builds i havent been doing anything with oemizer at all and it still hasnt been working, and i dont think i am doing anything extra in buildos that i havent done before in successful ROM images...it seems sort of erratic.
any suggestions/hints/comments would be great, thanks a lot.

you can't just hold the two buttons and press the reset. You have to hold the two buttons at the same time, then while holding them, use the stylus to hold the reset until it restarts. If you just tap the reset button while hold, it doesn't work.

360discgolf said:
You shouldn't need to connect to activesync to reboot. After you run ImCokeMan's unlocker you should be unlocked until you run it again.
As I said in the last post, all you have to do to get to the boot loader is hold down the power and camera buttons at the same time. This will put the phone into the boot loader and you should be able to flash back to the stock rom and start over.
It kind of sounds like you relocked the phone and then tried to boot a custom rom.
Click to expand...
Click to collapse
i'm having a similar problem. my attempt at flashing didn't go over that well and now when I turn off the device, I can't turn it on again unless I do a soft reset. I tried doing the power/camera thing but all it does is ask "are you sure, yada yada" and then the devices turns off. you were talking about a stock rom? where would I get one and how would I re-flash the rom (assuming that's the problem in the first place.).
Thanks!

vkolas said:
i'm having a similar problem. my attempt at flashing didn't go over that well and now when I turn off the device, I can't turn it on again unless I do a soft reset. I tried doing the power/camera thing but all it does is ask "are you sure, yada yada" and then the devices turns off. you were talking about a stock rom? where would I get one and how would I re-flash the rom (assuming that's the problem in the first place.).
Thanks!
Click to expand...
Click to collapse
what carrier are you?
EDIT: also:
1) what os version are you running? (build number)
2) what radio are you running?
3) what bootloader are you on? (can be accessed via holding power + camera button and poking reset hole)
4) what are the orange numbers in the very bottom right of the screen when you are booting up?
these kinds of things all need to kind of jive for the sleep function to work correctly

jim256 said:
i used imcokemans unlocker (which i have done before) ...
Click to expand...
Click to collapse
If you used the imcokemans unlocker a 2nd time, I believe you re-lock your phone.
You also mentioned that you tried to flash the ROM from the Welcome Screen. That certainly won't work. You have to be at the unlocked rainbow bootloader screen which will load when you run the RUU or when you press Power-Camera-Reset. If it doesn't go into bootloader then you've probably re-locked your phone.

denasqu said:
If you used the imcokemans unlocker a 2nd time, I believe you re-lock your phone.
You also mentioned that you tried to flash the ROM from the Welcome Screen. That certainly won't work. You have to be at the unlocked rainbow bootloader screen which will load when you run the RUU or when you press Power-Camera-Reset. If it doesn't go into bootloader then you've probably re-locked your phone.
Click to expand...
Click to collapse
haha sorry this is a problem that i had a VEERRRRY LONG time ago. have learned a lot since since then, now it is this other fella here we are trying to help him
thx tho!

Cincular 8525 stuck in Bootloader

I have a Cingular 8525 running WM5 that is stuck in bootloader screen. I have tried to soft and hard reset ... just boots back to the same screen, I can't turn it off once in the screen and when i sync via usb to the pc i get the message that the "usb device that is connected is malfunctioning" I have not done any upgrading at all and the phone worked perfectly right up till the time i powered it down and restarted into the bootloader screen.
Please can someone out there help me with this issue?

Zulu137 said:
I have a Cingular 8525 running WM5 that is stuck in bootloader screen. I have tried to soft and hard reset ... just boots back to the same screen, I can't turn it off once in the screen and when i sync via usb to the pc i get the message that the "usb device that is connected is malfunctioning" I have not done any upgrading at all and the phone worked perfectly right up till the time i powered it down and restarted into the bootloader screen.
Please can someone out there help me with this issue?
Click to expand...
Click to collapse
same problems, run perfect before with schaps wm6 rom then flash to faria wm6.1... not feel good with faria. try to flash with other rom then the problem start ..
how to recover ....... please help

Asfarizal said:
same problems, run perfect before with schaps wm6 rom then flash to faria wm6.1... not feel good with faria. try to flash with other rom then the problem start ..
how to recover ....... please help
Click to expand...
Click to collapse
Manage to solve the problem ...thanks WIKI !!
Go to Bootloader mode: Hold side OK and POWER buttons together and reset with stylus
Then Flash to any ROM you want !!

Thanks .... But
Thanks for the reply ... but i have no idea how to do what you tell me, I am new to all this phone "stuff" as a matter of fact this is the first time that i am ever using one of these forums. I have read till i am cross eyed but dont actually understand what you are talking about ... now don't let that scare you away as i am willing to learn and i am not braindead ... you all had to start sometime in this, not so. I get that i need to try and reflash my rom...
so is there some type of rom update software that i need? ... what is a hard SPL?? ... and who is Schaps?? .. sorry guys to do this to you but i would like to get into this game and i need some ( well maybe a lot ) of pointers.
Thanks for your time.

1. Search for "mr vanxs guide" so you have an idea on what you're doing.
2. OK, as Asfarizal said "Go to Bootloader mode: Hold side OK and POWER buttons together and reset with stylus". If you cant work out what the buttons are, go to the manual. it will tell you.
3. type in "hard SPL" in search on the forum & download the .zip or .rar file. this should have 2 files inside when opened,
a). RUUWrapper.exe and
b). RUU_signed.nbh
sync Hermes and double click .exe file. follow prompts.
4. find a rom that you want (would suggest TNT SE as a fairly good rom for noobs... good and stable, no problems...) Again download, then (and this is personel preference) format an sd card fat 32 and copy RUU_signed.nbh into root directory. Rename it Hermimg.nbh. Put into Phone and put into bootloader(make sure the battery is more than 50%) follow prompts. This should get you out of trouble. You can also sync your Phone and double click on the RUUWrapper.exe HOWEVER, if you should reset your computer, pull out the usb cable or have anything else happen to the computer that interrupts the flashm, you could end up with a worse brick than you have now. try to read up on flashing (search for "mr vanxs guide") and this should help you a lot if you have other questions. Good luck and happy flashing......

Thank You
I will follow the instructions you gave and try to get it going this weekend.
Thank you so much for your time

Zulu137 said:
Thanks for the reply ... but i have no idea how to do what you tell me, I am new to all this phone "stuff" as a matter of fact this is the first time that i am ever using one of these forums. I have read till i am cross eyed but dont actually understand what you are talking about ... now don't let that scare you away as i am willing to learn and i am not braindead ... you all had to start sometime in this, not so. I get that i need to try and reflash my rom...
so is there some type of rom update software that i need? ... what is a hard SPL?? ... and who is Schaps?? .. sorry guys to do this to you but i would like to get into this game and i need some ( well maybe a lot ) of pointers.
Thanks for your time.
Click to expand...
Click to collapse
Looks like you've got a lot of reading to do, and a problem to sort out. Firstly a couple of answers...
Schaps is a Rom Cooking guru (makes custom versions of WM5, WM6 etc). When you get your phone sorted out I'd recommend trying one of his roms.
Hard SPL. The SPL is part of the bootloader which effectively dictates how a rom is flashed and what roms can be flashed. HardSPL is a custom version of this which allows you to flash any rom from any carrier. It also protects against a bad flash in many cases. It is recommended before you try flashing any new roms or radio roms. Use Hard-SPL-V7 at the bottom of the first post here.
The Rom upgrading software is contained in any of the cooked or carrier supplied roms. It is normally a .zip file which cotains 2 files: xxxxxRUU.exe and RUU_signed.nbh. You run the .exe file from your PC when connected to your phone via USB. More details of how to do this are in MrVanx's guides. Also other resources here.
Now to try to sort your phone out...
What is displayed on your screen when in bootloader mode? It should be something like this:
HERM200
IPL-1.04
HERM200
SPL-2.10.Olipro (This is HardSPL V7)
If you don't have an Olipro SPL then you need to get HardSPL onto your phone. If you haven't done any upgrading and have had the phone from new then I guess you don't have hardSPL.
Now you need to fix your USB Malfunctioning problem. I can't help too much here except to suggest trying a different cable, different USB port or different PC. Also, if you are running Vista try an XP maxhine. When you connect to the PC does your phone show Serial or USB on the screen? If you can't get a USB connection, all is not lost - you can re-flash your rom using an SD card, method here.
There is a thread about un-bricking phones which may help.
There are various diagnostic tools (which can also screw your phone if used incorrectly). The favourite of these is MTTY but you need a USB connection to use this.
If your phone is in warranty I'd recommend getting your supplier to sort it out, but if not I'd try to re-flash an ORIGINAL supplier rom (Cingular I guess). You can get links to the official supplier roms here.
I think (might be wrong) that sometimes when stuck in bootloader you need to flash an official rom, not a cooked one to recover your phone - then you can run HardSPL and then flash cooked roms again.

Cingular 8525 stuck in bootloader
Thanks for the reply ... lots of great input.
Now to answer some of your questions.
1) When I power up the phone (only pushing the power button ) it goes straight into the bootloader screen without pushing any other buttons, and it displays
HERM100
IPL-1.01
HERM100
SPL-1.06
Then at the bottom in the white bar it says "Serial"
The only way that i have found to power it down again is to remove the battery, there is no response from any single buttons after it is in bootloader
the soft reset and hard reset work but it just goes right back to the bootloader screen after.
2) The USB malfunction. This only started after the phone "crashed" and before that it worked great ... well i only used it to sync up to my work pc for the contacts and to get pictures onto my hard drive.
all the PC's that i use are running XP. I have tried my home PC and my Laptop
and the work PC and all of them have their own cables and they all say the same thing ... "the USB device is malfunctioning"
I am sure that when i get the phone going again the USB will start to function again.
3) Phone warranty ... I bought the phone off e-bay from a store in new york about 10 months ago as a "new unlocked cingular 8525" it was new and unlocked, but i have no idea how they unlocked it. I would assume that there would be no warranty now and in any case i live in Canada and would have to ship it down to the states to an AT&T repair center and that sounds like a nightmare to me with the customs and so on.
I will give you a little more background on the problem. the phone worked like a charm without any problems at all for the 10 months that i had it, then the morning of the crash the phones alarm did not go off in the morning and i was almost late for work ... i did not pay it any further attention untill at 3:26pm
that afternoon the alarm went off ??????? (it was set for 6:05am) so i checked the main clock time, it was right. I then checked the alarm time, it was right ??? So i figured that something must have just got confused, so i powered down the phone with the power button to just restart it and while it was powered down i removed the battery to take the oportunity to to clean all those fuzzies and dust that collect in the battery compartment out and put it all together and powered it up again (just by pushing the power button) and this wierd red, green, blue and white screen appeared and that is all that i have seen since ???
I hope that answers your questions and i will start going through the links that you sent and get to reading ... will there be a pop quiz ... lol
Thanks again for your time and i very much appreciate all the time that all of you have spent on me and my phone ..... I know that you all just feel bad for me because i now have to use a Motorolla V551 ... lol

Great Work
ultramag69 said:
1. Search for "mr vanxs guide" so you have an idea on what you're doing.
2. OK, as Asfarizal said "Go to Bootloader mode: Hold side OK and POWER buttons together and reset with stylus". If you cant work out what the buttons are, go to the manual. it will tell you.
3. type in "hard SPL" in search on the forum & download the .zip or .rar file. this should have 2 files inside when opened,
a). RUUWrapper.exe and
b). RUU_signed.nbh
sync Hermes and double click .exe file. follow prompts.
4. find a rom that you want (would suggest TNT SE as a fairly good rom for noobs... good and stable, no problems...) Again download, then (and this is personel preference) format an sd card fat 32 and copy RUU_signed.nbh into root directory. Rename it Hermimg.nbh. Put into Phone and put into bootloader(make sure the battery is more than 50%) follow prompts. This should get you out of trouble. You can also sync your Phone and double click on the RUUWrapper.exe HOWEVER, if you should reset your computer, pull out the usb cable or have anything else happen to the computer that interrupts the flashm, you could end up with a worse brick than you have now. try to read up on flashing (search for "mr vanxs guide") and this should help you a lot if you have other questions. Good luck and happy flashing......
Click to expand...
Click to collapse
Thanks a lot man & great work i unbricked my Herm100 with method u mention above thanks a lot & great job keep it up

I also have this problem.
I d/l Hard-SPL-V7
and when i run RUUWrapper.exe
I get an error saying the application failed to initialize properly (0xc0000135)
What's going on?
How do i fix this?
this happened when i was trying to unlock the phone.
Thanks

need help
when i switch on my orange herm100 it shows On the bootloader screen is displayed:
HERM100
I PL-1.01
HERM100
SPL-1.40.01ipro
history : i buy unlocked orange phone
fewdays back i found no imei ,
yesterday i try to flash by micro sd but in gsm stage its gets hang no progress after extrom stage
IPL - OK
BOOTLOADER - OK
SPLASH1 - OK
SPLASH2 - OK
EXTROM - OK
GSM - (NO ACTION)
OS -
i tryed several time no action, i cant connect by mini usb.
PLEASE help me
tell me which it the right rom to chose? step by step procedure..
how to rectify imei?
thanks and regards
kirtibas

kirtibas, sorry it took so long to reply, 1st thing I'd do is upgrade to SPL 2.10 olipro. This is safer to use than others. then I'd suggest reflashing a stock rom to see if that works. After stock rom works then use a cooked rom as your heart desires... Cheers...

My HTC Magic is bricked

I've got a "Brick" HTC Magic - Vodafone.
Basically, when i press the power button doesn't start. It happened after follow the "Install / Update SPL" ( http://code.google.com/p/android-roms/wiki/SPL ) guide.
Is there any way to recover it? or should i put it on the bin?

You're going to have to be more specific than "it doesn't start".
Does it turn on? If so, does it hang at the htc magic screen? Can you hold vol-down and press power (while still holding vol-down) and load a screen with three androids on skateboards? If you can do the last step, it's not bricked, and you should look at the thread I have below about bricking and semi bricking, one of the users on there gave a great amount of information on what you can do if your phone's not working right (bricked).
Caid.
444

Caid444 said:
You're going to have to be more specific than "it doesn't start".
Does it turn on? If so, does it hang at the htc magic screen? Can you hold vol-down and press power (while still holding vol-down) and load a screen with three androids on skateboards? If you can do the last step, it's not bricked, and you should look at the thread I have below about bricking and semi bricking, one of the users on there gave a great amount of information on what you can do if your phone's not working right (bricked).
Caid.
444
Click to expand...
Click to collapse
Hi Caid, thanks for the reply! sorry for the short message without details.
Here is the answer for your first question (sadly, the rest of questions can be skipped):
Does it turn on?
It doesn't
It was after follow the guide i mentioned before. I tried to update the SPL, but something went wrong and my phone didn't turn on again.
So... I think I have to accept the fact is not going to work again.
Is there any kind of service able to fix this?
Anibal

No display at all? no backlight on the screen? no vibration (signifying it's past a certain point in the loading stage)?
You probably tried taking out the battery for 10 seconds and then putting it back?
As Caid444 asked, tried holding Back+Power for a few seconds (after making sure power is off and not just hanging. Take off battery for 10 sec and reload)? Tried holding Home+Power after making sure power is off?

please i need some help htc touche cruise
hi everyone. I have a big problem with my htc touch cruise when I installed a hard spl htc dedicate a Diamond.donc I had a white encrant after I did a hard reset since my htc no longer I have a black encrant are neither green nor orange but when I connect with the pc I am data interface and it does not recognized my htc. In my pay is not qualified repairman three non réparé.aidé unable to please me I tried the commands mtty.exe but does not c I do not really know how it works.
thank you for your patience and for help

parrot5 said:
No display at all? no backlight on the screen? no vibration (signifying it's past a certain point in the loading stage)?
You probably tried taking out the battery for 10 seconds and then putting it back?
As Caid444 asked, tried holding Back+Power for a few seconds (after making sure power is off and not just hanging. Take off battery for 10 sec and reload)? Tried holding Home+Power after making sure power is off?
Click to expand...
Click to collapse
I'd really like to say it DOES something... but it doesn't . I tried Volume down + power, back + power and several more combination always taking out the battery and putting it back.
It's bad... Do u know if there's any hardware service for this?

Just a wild guess, but since the phone sucks more battery, then a vampyre on rampage.
Could it be an idea, to charge the battery before, or have the usb cable pluged in, when you press back+home? (the same buttons you used to enter fastboot)

I'm pretty sure what you're trying to say is, you know enough about the phone to know how to bring it into it's multiple boot options, and none of them make the phone even burp. So there's no need to tell you to press this button plus that button, or insert usb or remove usb, or battery or such, because you've already done all that.
Well, I'd have to agree with you that it's dead. Unfortunately, there's nothing to do at the moment. I'm guessing (or maybe just hoping) that in the future there will be an unbricker for our phone, much like those available for many htc branded winmo phones. In the meantime, how old is your phone? Can you still bring it back?
Caid.
444
p.s To anyone else who's trying to figure this out, let's assume that he's already tried the many variations of recovery procedures and that it's still not working.

argc79 said:
I've got a "Brick" HTC Magic - Vodafone.
Basically, when i press the power button doesn't start. It happened after follow the "Install / Update SPL" ( http://code.google.com/p/android-roms/wiki/SPL ) guide.
Is there any way to recover it? or should i put it on the bin?
Click to expand...
Click to collapse
If it's really a brick and we all want to learn something from this then we need to know the following :
1. What was your original SPL
2. To which SPL did you "try" to upgrade? (I hope you didn't try to flash a G1 SPL on your Magic...).

Amon_RA said:
If it's really a brick and we all want to learn something from this then we need to know the following :
1. What was your original SPL
2. To which SPL did you "try" to upgrade?
(I hope you didn't try to flash a G1 SPL on your Magic...).
Click to expand...
Click to collapse
That's how my brick arrived ! Tried Hard SPL, after installing the one you suggested. Yours okay, Hard SPL no. But even after installing the spl, no fastboot adb.

BRICKED by HARD SPL ( the recommended )
Same here, I have just bricked my new vodafone HTC Magic (Vaffanc...)
downloaded from here: http://code.google.com/p/android-roms/downloads/list?q=label:SPL
I hope something can be done. It is not reacting to power button at all.

Amon_RA said:
If it's really a brick and we all want to learn something from this then we need to know the following :
1. What was your original SPL
2. To which SPL did you "try" to upgrade? (I hope you didn't try to flash a G1 SPL on your Magic...).
Click to expand...
Click to collapse
I think you are right, I have flashed the G1 SPL. But the page is really not clear, it start speaking as Dream/Magic and probably it is only for Dream. Since it says to apply the Hard Spl and in the download link(http://code.google.com/p/android-roms/wiki/SPL) there is no clue that it is not for the G2.
Any idea? anybody got it changed from the shop with no problems? (mine is vodafone in the netherlands)
Me idiot, I have to leave tomorrow for holidays!

byronhero said:
I think you are right, I have flashed the G1 SPL. But the page is really not clear, it start speaking as Dream/Magic and probably it is only for Dream. Since it says to apply the Hard Spl and in the download link(http://code.google.com/p/android-roms/wiki/SPL) there is no clue that it is not for the G2.
Any idea? anybody got it changed from the shop with no problems? (mine is vodafone in the netherlands)
Me idiot, I have to leave tomorrow for holidays!
Click to expand...
Click to collapse
as far as i can see no need to flash spl on vodafone magic. i have the same phone and all i did was root with Rav1.1.1G.img and flashed rom of my choice. you have flashed phone with g1 spl and it actually says g1 on the link you provided..........can't see how you missed it. with phone off press home+power button as that bring up recovery image. Rav image file is safer due to that. i am sure if hardspl was available for Magic it would be posted on here as a sticky

hi
all
i have been recevied new htc magic phone from vodafone on line contract . after i done hardspl my device gone blank not power back on . and change amber light it working .... but i cant power on my device how can i reset device with go gui mode ? i had update hardspl from follwoing link http://code.google.com/p/android-roms/wiki/Install_Hard_SPL . i cant take it vodafone shop becoz just week before same happen so this is my second new phone . please help me if know any other idea
thank you
dana

thanant said:
hi
all
i have been recevied new htc magic phone from vodafone on line contract . after i done hardspl my device gone blank not power back on . and change amber light it working .... but i cant power on my device how can i reset device with go gui mode ? i had update hardspl from follwoing link http://code.google.com/p/android-roms/wiki/Install_Hard_SPL . i cant take it vodafone shop becoz just week before same happen so this is my second new phone . please help me if know any other idea
thank you
dana
Click to expand...
Click to collapse
You did brick one with the hardSPL and now you bricked another with the same stuff? Didn't you learn the first time? Only way is to go back to the store and tell em you did it again.

thanant said:
hi
all
i have been recevied new htc magic phone from vodafone on line contract . after i done hardspl my device gone blank not power back on . and change amber light it working .... but i cant power on my device how can i reset device with go gui mode ? i had update hardspl from follwoing link http://code.google.com/p/android-roms/wiki/Install_Hard_SPL . i cant take it vodafone shop becoz just week before same happen so this is my second new phone . please help me if know any other idea
thank you
dana
Click to expand...
Click to collapse
It seems to me you need to go back to basics and start here

A noob question but what exactly does flashing a new SPL unlock.
I got my Vodafone UK HTC magic and simply Downloaded a 32B ROM and used nandroid backup to apply the update.zip and it installed fine and can use Root required apps.

hi all
My HTC magic was bricked after update SPL. Now when press power button, it stuck at HTC magic logo, anyone have solution for fix its?

I Can not understand how can this be possible. Why guys all of you, don't read before trying to change your SPL???? You even don't need any changes about it?! Why do you try to change the SPL? Do you know what that SPL does? I think most of you - don't.
My next question is why all of you are trying to flash the G1 SPL onto Magic phone? Are you crazy or what? There is NO HARDSPL for Magic (G2, Sapphire or whatever you want to call this device)!
The SPL collection is posted in this forum by Amon_Ra, and if someone want to change the SPL can do this by downloading some of the SPL collections posted here.

say2k said:
hi all
My HTC magic was bricked after update SPL. Now when press power button, it stuck at HTC magic logo, anyone have solution for fix its?
Click to expand...
Click to collapse
Power off your phone! Then press and HOLD the "back button", while holding it press once the red one(which you usually use to power on the phone). It will power on (i hope). If you get in fastboot mode then everything will be fine.

Tmobile HTC HD2 BOOTLOADER

hello, i was hoping someone could help me with this. I am trying to load the Android system on my phone. But it says i have to install the HSPL (HardSPL) on the phone first. I tried to do that but it asks to review the version of SPL on my phone by holding down the volume down key and check the version on the bootloader but it doesnt come up. I tried isntalling the HSLP and the HSLP2 package on this site... and didnt work. I was wondering if someone could help me on this... This phone is super glitchy and wish i can get it working a bit better. Thank you guys.

ecruz9 said:
hello, i was hoping someone could help me with this. I am trying to load the Android system on my phone. But it says i have to install the HSPL (HardSPL) on the phone first. I tried to do that but it asks to review the version of SPL on my phone by holding down the volume down key and check the version on the bootloader but it doesnt come up. I tried isntalling the HSLP and the HSLP2 package on this site... and didnt work. I was wondering if someone could help me on this... This phone is super glitchy and wish i can get it working a bit better. Thank you guys.
Click to expand...
Click to collapse
What instructions for Android are you reading? None of the real versions need HSPL at all...they all load using HaRET, an app that goes on your SD card. If you see instructions to use HSPL to get Android on your HD2, it's clearly one of the fake ones that was floating around.
Check out the thread below for all the current details on the real deal:
http://forum.xda-developers.com/showthread.php?t=719646

ecruz9 said:
hello, i was hoping someone could help me with this. I am trying to load the Android system on my phone. But it says i have to install the HSPL (HardSPL) on the phone first. I tried to do that but it asks to review the version of SPL on my phone by holding down the volume down key and check the version on the bootloader but it doesnt come up. I tried isntalling the HSLP and the HSLP2 package on this site... and didnt work. I was wondering if someone could help me on this... This phone is super glitchy and wish i can get it working a bit better. Thank you guys.
Click to expand...
Click to collapse
You have to reset your phone and HOLD the VOLUME DOWN and POWER at the same time and you will be able to check your SPL version.

Same Problem
I am having the same problem i can't get into bootlader by holding down the power button and volume down button tried and tried and tried again and all it does is come up and show the same old tmobile splash screen and from my memory of doing this before you don't see that when going into bootloader it just automatically goes into bootlader .. my question is how possible is the brick possbility of doing hardspl4

Well seeing as how majority of us do not report any situation of us bricking our phones due to flashing HSPL, I can say the possibility is almost non existent, that is if you're part of the norm of this society.
Are you sure you're holding vol down before you power up your device? Do your volume keys work with winmo/android/WP7?

[Q] Stuck at bootloader at boot

Hi
A friend of mine has a HD2, never HSPL or anything and still running on 1.42 rom.... Now everytime it boots it goes straight into the bootloader. Since its never been messed around with I find it odd, seen it before with people with other phones. Would this just be a corrupted ROM and therefore it goes there, would if poss a stock rom flash be able to restore the phone, if that is not the case then a warranty return is still valid, but obv not wanted.
What do you think, will this work? I did search but everyone's posts come up with I task 29 and now stuck... etc and not from a stock bootloader as well!
Cheers any help will be appreciated, my first thing I will get him to try is a rom reflash but that will be tonight, I'll update on the progress then!

First thing I would check is if his volume button is stuck for some reason. Second would be to see if it detects a USB connection, then hard spl and new rom from that point. Keep us posted.
Sent from my GT-P1000 using XDA App

chris10230 said:
Hi
A friend of mine has a HD2, never HSPL or anything and still running on 1.42 rom.... Now everytime it boots it goes straight into the bootloader. Since its never been messed around with I find it odd, seen it before with people with other phones. Would this just be a corrupted ROM and therefore it goes there, would if poss a stock rom flash be able to restore the phone, if that is not the case then a warranty return is still valid, but obv not wanted.
What do you think, will this work? I did search but everyone's posts come up with I task 29 and now stuck... etc and not from a stock bootloader as well!
Cheers any help will be appreciated, my first thing I will get him to try is a rom reflash but that will be tonight, I'll update on the progress then!
Click to expand...
Click to collapse
The post above me is correct check and make sure the volume down button is not stuck/Hung in the down position. If it is stuck in the down position like it is being held down at boot then this is the cause of it going straight to bootloader at boot up. If there is no problem with the volume down button then try a hard reset of the HD2. Warning this will reset your friends HD2 tolike it was fresh out the box so any photos, videos, documents, and etc that is not on the SD card they will lose. Also any contacts that are not backed up withan app like Microsoft My Phone will be lost. To do the reset while the HD2 is off bold the volume up and the volume down buttons down and press and bold the power button down. When you see the tri color screen come up release the volume and power buttons and follow the instructions on the screen (hint: you will want to press the vume up button). Now if after the Hard reset your friends HD2 still goes to bootloader at boot up then download and flash the stock ROM for their HD2 you can find it on HTC.com but make sure you varifiy that it is for their HD2 by entering the serial number of their HD2 you can find the serial number look under the battery. To flash the ROM let the HD2 boot up to the bootloader and then connect it to the computer via USB cable and wait for the Serial in the white bar of the boooader screen to change to USB and for your computer to show it recognize the pbone and then run the .exe or RUU wich everone the ROM has.

Never thought of the key being held done will try that first.
Also I won't HSPL'ing as its in warranty and a half HSPL'ed phone is well useless

OK so i feel like a bit of an idiot for this one. Turns out what I call a bootloader and he does is totally different. For me Its the tri-colour screen, for him its the red/orange windows boot screen. So it was all solved by a HR. Great..
Sorry for those who offered the advice but it really was not needed. but solid advice it was, you always can rely on help in here