Related
I have done hard reset and soft resets and still my wifi is not connecting.
Finally my EDGE is working great but wifi not. Whenever I try to connect my SSID is set to "EMC Wireless Internal" channel 11. I have no idea where this cam from but I can not get rid of it. I have a new FIOS Actiontec router with wireless enabled to my network name, channel 10. And Hitchhiker tries to connect but it keeps getting bumped off.
I have gone into MediaNet and turned off the proxy and checked for it to go onto the internet on Cingular GPRS.
I have not had a problem connecting before on wifi. I wonder if the router is a problem here, or if my phone settings are screwed up.
And ideas?
Thanks
The WiFi - EDGE contengency
*The Bad News*
By default, if EDGE/GPRS is configured to work, WiFi is rendered useless.
You didnt mention what carrier you have. I have Cingular and they even state on there website that If you configure the Edge/GRPS to connect, then WiFi may not work.
*The Good news*
I have my 8125 working with both Edge and WiFi. Heres what I did:
1. Open Connnections and click on the 'ADVANCED' tab.
2. Click on 'SELECT NETWORKS'.
3. The top pull down should be set to 'MY ISP' or, if you have named your WiFi connection something different, select it here.
4. Click 'EDIT' under this pull down and set connection to 'AUTO PICK'. 'OK' back to Network Management screen.
5. The bottom pull down should be set to 'MEDIA NE'T.
6. Click on 'EDIT' under this pull down. This is where you will set up EDGE using your carrier's settings.
7. 'OK' your way back out. Your done.
These settings let WiFi try to connect first. If no WiFi is available then EDGE/GPRS is used.
Good Luck!
Thank you! Worked for me, but videos streamed from orb still aren't working
Wierd-Fi
I also have WiFi problems after installing HTC official upgrade
ROM 2.25.11.1 WWE
Date 5/11/06
Radio 02.25.11
Protocol 4.1.13.12
ExtROM 2.25.11.102
Everything is great except after successful connection to home WiFi it disconnects after maybe 5 to 15 seconds ... network becomes "unavailable" .. no error message. This happens even when not connected to CIngular EDGE/GPRS (flight mode ON then, individually enable WiFi ON for what that's worth). When I delete my home network WiFi entry to force a re-recognition and setup, it recognizes the wireless net just fine (again) but same behavior.
All my settings are already set as suggested by ralugniC8125 in this thread. I had not tried any of the other ROMs with added features/hacks/fixes found on this website ... would any of them behave differently, you think? PHone was bought from Cingular .. I have not done any unlock procedure (don't really need to from a service standpoint but will if necessary to make a new ROM work right).
Any thoughts appreciated...
tskelton said:
Everything is great except after successful connection to home WiFi it disconnects after maybe 5 to 15 seconds ... network becomes "unavailable" .. no error message.
Click to expand...
Click to collapse
I have just purchased an unlocked Tilt from eBay. I have been scanning the wiki for days now, along with other sources, and to no avail. I still cannot get my WiFi to work properly. If any one has had this issue and has found a solution, I would love to know it!
ok, here's a suggestion since none of you have mentioned it.
Diable the MAC (Media Access Control) Binding on the router. This should help.
Maybe yall can help me now I have it attempting to connect however it only connects to gprs and it even shows it has a great wifi signal
Still Wifi-less and Woeful
lobotomy said:
Diable the MAC (Media Access Control) Binding on the router. This should help.
Click to expand...
Click to collapse
Thanks for the suggestion. This did not help unfortunately. I should mention that I have tried to access several different types of routers... with and without security, and while they are showing up as being available, they will not stay connected for more than a second or two.
Any other possibilities?
I'm really racking my brain on this one. I would greatly appreciate any ideas, as I've long run out of them.
---Intro---
I have a one week old Wizard (Cingular 8125 variant). It has one of the latest roms with AKU2 on it. Using Registry Wizard, I selected the option to add wireless G compatibility at some point in time. Wireless initially worked after setting my phone and router up per a tutorial on a popular Axim users forum. A day or two later I went to use WIFI and I get nothing. GPRS/EDGE initially worked also, but at the same time it stopped working. I've spent countless hours since trying everything I possibly can to get WIFI to work.
---The problem---
I am not able to connect to the wireless router. My Wizard sits on "connecting" forever then maybe 5 mins later it says unable to obtain an IP address. When I look at the status, it says 0.0.0.0 for the IP address the whole time it says connecting. Since the problem started, I have yet to actually connect using any settings. The first day I configured the wireless it worked perfectly, with WAP encryption and all.
---Some of what I have tried---
On my US Robotics wireless router I've turned mac filtering and all security settings off, making an open network. I removed the WAP setting for the connection on the Wizard as well. I've tried all the suggestions I can find on any WM 5 and 2003se related forums to no avail. I've tried all the various combinations of limiting to B/G only or mixed, using work/internet settings, and deleting WIFI connections and creating new ones. I don't have a proxy setting in any of my connections. The whole time my battery usage is set to the highest (performance) setting and I'm right next to the wireless router. I've tried turning off all proprietary speed enhancement options. I even installed a program (Pocket DHCP) recommended by Axim PPC users to figure out why I'm not receiving an IP. Since I'm not really a DHCP wiz, I can't tell from the results what is causing this.
I'd be greatful if anyone can help me with figuring this one out. Thanks in advance!
maybe a dumb question, but...the wireless part of the router is working fine? did u tryed with a laptop or pc?
did u tried a hard reset?
That's actually a great question. I did connect fine the first day I configured the wireless and made no changes from then until it stopped working, so I'm just assuming that the router is working properly. Unfortunately I don't have access to any other wireless device/laptop to test it with.
I'm getting ready to do a hard reset right now. I was really wanting to avoid this but I think I have no other option. Hopefully this will fix whatever setting was messed up. I have a slight hunch that the registry change for allowing G access was the cause of the problems.
maybe i missed this in the original post, but have you tried making your device use static ip's on the lan instead of dhcp?
Shogunmark:
I didn't try static IP's for two reasons. 1. Firstly I couldn't figure out how to set this up. 2. I don't want to have to fiddle with removing the static IP when I'm away from home trying to use a different wifi hotspot. I would like it to be seamless and just connect when I turn wifi on near any unsecured network (other than the usual pressing OK to connect).
STATUS UPDATE:
I did a hard reset and directly after this I tried to connect to my open network. Amazingly GPRS/EDGE now works, but WIFI still does not. Then I did a factory reset on my USR router then changed the settings back to how it was just set before. Now, I'm connecting. This doesn't make any sense since the settings are the same now but it's working, maybe theres a glitch with the router that this fixed. This small progress seams like a miracle.
Now that I can connect to WI-FI, I have a new problem. When I try to load pages in internet explorer, it says page not found or whatever the standard error message is. I'm so close I can smell it. There must be some setting that needs to be changed on my Wizard.
SUCCESS
I report that I am now absolutely delighted with network connection on my Wizard. After hard reseting the phone and the router, now I can connect to both WIFI and GPRS. Not only that... but also PIE will choose WIFI if I'm connected to a wireless router, otherwise it will default to GPRS/EDGE without any interaction from me. This stuff is really awesome when it works. It is difficult to setup correctly though.
somehow wifi routers r not 100% reliable, every now and then i need to reset my linksys or i cant get ip as in your case...but with a normal reset is enough in my case...
That's good to know. Maybe I didn't even need to hard reset my Wizard, just the router. Now I know to start with the router because it's much easier to reconfigure. This is the first time that I've implemented WIFI on my own network. What happens if a public WIFI spot won't give you an IP anymore? Surely you just can't go and reset it. Granted it's not nearly as old as Ethernet, WIFI has been out for long enough that you think they would have these major kinks worked out.
Nicnatros said:
... but also PIE will choose WIFI if I'm connected to a wireless router, otherwise it will default to GPRS/EDGE without any interaction from me.
Click to expand...
Click to collapse
How did you manage this? I have been struggling for ages to set things up this way. Can you post your settings from settings>connections>connections>advanced>select networks. Also settings>connections>network cards.
I would like to be able to just turn on wlan from comm manager and use wifi to surf and connect to my wireless lan, but if no wifi available to default to my T-mobile gprs connection for surfing. Currently having to manually change the settings "Programs that automatically connect to the Internet should connect using" My Work Network or Tmobile gprs each time I want to use either.
What I want is the option
if wifi available
use wifi
else use gprs
Well my friends and I were like sitting around drinking foo-foo drinks and I just like stumbled upon the answer. Just kidding, it's fun to play the role of your avatar, especially mine.
Settings, Connections tab, Network Cards, Network Adapters tab: My network card connects to Internet
Settings, Connections tab, Connections, Advanced tab, Select Networks: Set first one to My work network. Set second one to MediaNet (or your gprs/edge/etc connection profile).
Now with those set, edit the My Work Network profile and make sure that under the proxy tab check connects to the internet option, uncheck the proxy option. Now edit your MediaNet (or other carrier data plan) and make sure that this contains all options for your carrier like proxy, modem, etc. If you are a Cingular user, go here to verify all settings for medianet. (Note that you will ignore the beginning couple steps when they say to place medianet first in the "select networks" settings. Start after step 6. Also they used the CingularGPRS connection profile instead of the MediaNet one) http://www.pocketpcaddict.com/forum...ular-8125-windows-mobile-5-phone-edition.html
When you connect to your WIFI router first and it asks you if it's work or internet, always select internet. If you are not sure what it's set at, go out of range or unplug your router. Go into network cards and find your router SID, click and hold on it and select remove. Then when you try to connect to your WIFI again it will prompt you for this, make sure you use internet setting.
Now if you have done everything correctly, Internet Explorer will use WIFI when it's turned on and you get a connection. All other times it will default to GPRS/EDGE. I can go from one to the other back and forth without changing any settings, only enabling and disabling WIFI in the comm manager.
Trashman said:
somehow wifi routers r not 100% reliable, every now and then i need to reset my linksys or i cant get ip as in your case...but with a normal reset is enough in my case...
Click to expand...
Click to collapse
Linksys WRT54Gx? if yes look into dd-wrt . stable and has a lot of features . other hardware is supported as well just check on their webby.
yaboc said:
Linksys WRT54Gx? if yes look into dd-wrt . stable and has a lot of features . other hardware is supported as well just check on their webby.
Click to expand...
Click to collapse
I have read many many many posts about people having issues with the wizard and that exact router... I personally would stay away from linksys.. i work in a field that deal with 3rd party routers and such, anytime an end user has a linksys i can usually prove 90% of the time that its the culprit (80% of the time powercycling it does the trick)
Nicnatros said:
Go into network cards and find your router SID, click and hold on it and select remove. Then when you try to connect to your WIFI again it will prompt you for this, make sure you use internet setting.
Now if you have done everything correctly, Internet Explorer will use WIFI when it's turned on and you get a connection. All other times it will default to GPRS/EDGE. I can go from one to the other back and forth without changing any settings, only enabling and disabling WIFI in the comm manager.
Click to expand...
Click to collapse
This seemed to do the trick for me.
I am sure that I had tried all possible combinations previously but what the hell, it is working exactly how I want now.
Thank you
My brother gave me his 8525 after his girlfriend bought him a new phone. I then unlocked it using the unlocker that i found here so that I could use it on tmobile. I am on a prepaid plan and there is no way to get internet through tmobile with prepaid, but the WIFI should still work, but it doesnt. I can get it to connect to a network but when i open IE it wont go to any web adress i type in. Any ideas????
try changing your wifi power mode to best performance
XtreMe_G said:
try changing your wifi power mode to best performance
Click to expand...
Click to collapse
Tried that, and it didnt make any difference.
When I try to go to a site it says " Cannot Connect: Cannot connect with current connection settings. To change your connection settings, tap settings"
I have tried messing around with the settings, but i still cant get it to work right.
I think IE is still trying to connect to the internet via AT&T's network service instead of going through wifi.
Under start>settings>system do you have a proxy folder? maybe it's under programs as well. Look for it. If you do, run disable proxy.
Also go to start>settings>connections>network cards>network adapters
make sure this is reads under "my network card connects to: the internet"
select your 802.11b/g and make it "use server assigned ip address"
Hopefully that helps
hey man thanks for the tips, but it still is not working.
I found my proxy folder and ran disable proxy, my card is set to connect to the internet and it uses the server assigned IP adress.
But now when i try to use the internet it does not give me the "can not connect due to your settings" message, it just keeps trying to load the page but nothing happens.
go to start>settings>connections
click on connections
go to the advanced tab and click on select networks
on the first dropdown make it "my isp"
with the second select "my work network"
That should do it
i think that worked. Im not near a strong wifi signal right now but i think its doing the right thing. Ill know for sure tomorrow.
Thanks Pedro 2K
I was having the same issue on my 8525 after going to 6. Seems fine now. I'll try from work on Monday.
~E
well as it turns out that did not work. I still think it has somtething to do with it trying to connect to AT&t's network.
any other ideas?
i posted in another thread about a similar issue that i have and it is still not solved
some programs that use data on my device will not connect using 3g (pocket outlook using gmail), but they will connect when the wifi is on
it's kind of the opposite of what's going on with yours, but i believe the root of the problem is the same, because we are getting the exact same error message
i believe the problem stems from how/why windows mobile 6 organizes connections; which makes no sense to me whatsoever
under connections i have:
"My ISP"
"MEdia Net"
"Work"
Of course there is nothing even under my isp, or work, yet it wont let me delete them
i tried deleting them manually from the registry and that messed a whole lot of things up, so plz do not make that mistake
my media net settings ARE correct, but why are there so many different connections here, that arent even being used, yet i cant remove them?
what the hell is "MY Isp" ? I thought Media net was my isp...lol
this is confusing and frustrating
any more ideas????
Try disabling and data connections using this:
http://www.modaco.com/content/Pocket-PC-Software/246171/New-FREE-Utility/
This should make sure it is trying to go through wireless. Just a quick question, you are not connected to activsync while trying wifi are you?
ok, since you're using t-mobile, and only just want to use wifi, do this
go to start>settings>connections->connections->advanced
switch both to "my isp", click on edit (either one is fine), delete the modem number in there.
The last thing you need to do is disable the hidden proxy proxy. I dont know exactly how, cause i dont use the AT&T rom anymore, but its somewhere in the start menu, just poke around, there should be a "disable proxy' somewhere
@ surgex0
if you think that's confusing......on the tilt, they've added a 4th one.......AT&T ISP. But basically, whatever settings that was in My ISP, is now in AT&T ISP.
Fresh flash of WM 6.5 over radio 3.42.50 on a Titan. Under Network Management, I've selected that "Programs that automatically connect to the internet should connect using:" My Work Network, since I don't have a data plan. I go to Wifi settings, select Add New, put in the ssid, click through the security settings (temporarily disabled for this test purpose). My network shows up as "Unavailable". (I'm standing right next to the router). I click "Connect", it says "Connecting" for a couple of seconds and then goes back to "Unavailable".
What should I check first? I'm at my wits end.
You shouldn't have to "add new", your ssid should be automatically discovered and displayed in the list of wifi networks.
Did you connect to a wifi with your phone before, or is it a first attempt ?
Yes, I'd been connecting just fine until a few weeks ago. In fact, the refusal to connect was what prompted me to flash the thing -- figured that starting over might help.
So, your wifi connection was working well, but suddenly, for some obscure reason, it stopped working. Therefore, you decided to reflash your phone, but it didn't help, still not working.
Is that correct ?
I know I sound like a complete doofus, but yes, that's basically it. The weirdest thing is that every once in a while it'll find a wireless network and connect. But the connection never lasts for more than a few minutes, and then when it's gone the network is "Unavailable". And to anticipate your next question: There doesn't seem to be any rhyme or reason for when it works. At this point I'm thinking I'll pick up a used Titan or Vogue on eBay and junk this thing.
Did you try a different rom ? Could be a faulty rom.
I've tried several different roms, yes.
this happens in some roms...
go2 wireless lan settings and then go2 power mode.change it to best perfomance frm best battery
Hello,
I just bought a Leo. My provider is Vodafone IT.
From the very first moment, while WiFi is present in my house, the phone tried to connect to Internet via UMTS. It does so often when Wifi is temporarily unavailable.
After my old Glofiish M800, one year ago, made me spend 3€ for two consecutive connections for the duration of a half second each (1.50€ on connection then) I requested Vodafone to completely disable Internet access for my SIM card. All I did then was to connect the PDA to USB cable and SPB Weather immediately tried to update weather without even waiting for Net via ActiveSync to become available in a few seconds.
With Leo, I also deleted all network access points from configuration, set all profiles to Office Network and unchecked (my ROM is Italian) "This connection has Internet access" "Questa connessione dispone di accesso a Internet".
What occurs now is that often, but really OFTEN, even during the night, especially when I'm on the road and I'm not interested in Facebook, YouTube or weather, the phone turns on and two popup appear:
One as a notification "Called: " (before deleting AP "Called: web.omnitel.it" "Chiamata effettuata: web.omnitel.it"). The other as error message about problems with GPRS.
I also have to pay great attention to the second popup. Once, but fortunately not today, it went over the lock screen and I was unable to unlock it as the slider was below the popup. I was also unable to close the popup as the screen was locked so I had to soft-reset.
I only installed TomTom and Core Player for now.
I DON'T WANT TO PAY VODAFONE LOTS OF MONEY FOR UMTS ACCESS WITHOUT MY CONSENT, NOR SIGN UP FOR FLAT PLANS AS I HAVE WIRELESS ACCESS IN EVERY PLACE I USUALLY GO!!!
Can somebody help me tell Leo to NEVER TRY to use UMTS? I had to agree with Vodafone that I would have been unable to even send MMSs and perform videocalls until I restore UMTS, but I can't spend this huge money for the sake of weather and for greedy (it's the right word) software that just want to connect to the Internet whenever THEY want (ie. Windows Vista/7 does Windows Update only when Internet is detected, it never tries to connect until you do manually).
Thank you. Please anser me ASAP. If I don't find a solution, I will return the PDA to the seller (it's a great PDA, I wouldn't like to)
settings menu all settings connections connections advanced tab select networks change the top drop down to "my work network"
hope it helps!
Hi, I followed what you suggested and, in order to test faster, I tried to manually update weather from HTC Sense.
First of all, even if I uncheck the Internet access checbox from Office Network ("My work network" you mentioned), I always see it comes back again. I found that "ISP settings" only shows two tabs, and no Internet/proxy checkbox, so I also tested selecting this connection.
I also entered "*" as list of intranet addresses.
Every time I try to update weather, for all of these tests, I see the 3G arrows on top of notification bar flashing for a couple of seconds and the same exact alerts
Does your phone always connect to 3G?
[EDIT] I also tested http://www.htc.com/au/faqs.aspx?p_id=297&cat=264&id=118112, no result. But actually the help page says it clearly: it's normal that the phone will notice errors.
Is there any registry tweak or what?
Hello,
To solve your problem, go to the redfrogfish website, google to find the link. Download and install the Data Controller cab.This enables you to turn on/off the data connection function of the HD2
(I wanted to give you the link, but I am a new user and not allowed to do so)
Good Luck
djechelon said:
Hi, I followed what you suggested and, in order to test faster, I tried to manually update weather from HTC Sense.
First of all, even if I uncheck the Internet access checbox from Office Network ("My work network" you mentioned), I always see it comes back again. I found that "ISP settings" only shows two tabs, and no Internet/proxy checkbox, so I also tested selecting this connection.
I also entered "*" as list of intranet addresses.
Click to expand...
Click to collapse
I think you are going further into the settings than i need to.
settings - menu - all settings - connections - connections - switch to advanced tab - click 'select networks'
See my image 1 - setting the top dropdown to 'my work network' (or 'the internet', it gets called slightly diff thing depending on your setup, ,)) means it will look for whatever active connection is available and use that.
I also have a commmanager that has seperate on/off toggles for 3g and data.(see pic 2) So, if i turn off data connection, but leave 3g on, even though i have 3g (well, H) showing available on the top bar, if i go to update the weather it comes up with 'connection error'. If i start opera, it fails, etc etc.
Back into comm manager., turn back on the data toggle, everything works again.
If i turn off 3g, and leave data off, I get the same results.
paulmor said:
Hello,
To solve your problem, go to the redfrogfish website, google to find the link. Download and install the Data Controller cab.This enables you to turn on/off the data connection function of the HD2
(I wanted to give you the link, but I am a new user and not allowed to do so)
Good Luck
Click to expand...
Click to collapse
Thank you!
It did solve my problem
Here is the link you couldn't post, as it can be useful to the community:
http://redfrogfish.com/data-controller/
Thanks for the link, had a same problem which is solved now running this program.