Fresh flash of WM 6.5 over radio 3.42.50 on a Titan. Under Network Management, I've selected that "Programs that automatically connect to the internet should connect using:" My Work Network, since I don't have a data plan. I go to Wifi settings, select Add New, put in the ssid, click through the security settings (temporarily disabled for this test purpose). My network shows up as "Unavailable". (I'm standing right next to the router). I click "Connect", it says "Connecting" for a couple of seconds and then goes back to "Unavailable".
What should I check first? I'm at my wits end.
You shouldn't have to "add new", your ssid should be automatically discovered and displayed in the list of wifi networks.
Did you connect to a wifi with your phone before, or is it a first attempt ?
Yes, I'd been connecting just fine until a few weeks ago. In fact, the refusal to connect was what prompted me to flash the thing -- figured that starting over might help.
So, your wifi connection was working well, but suddenly, for some obscure reason, it stopped working. Therefore, you decided to reflash your phone, but it didn't help, still not working.
Is that correct ?
I know I sound like a complete doofus, but yes, that's basically it. The weirdest thing is that every once in a while it'll find a wireless network and connect. But the connection never lasts for more than a few minutes, and then when it's gone the network is "Unavailable". And to anticipate your next question: There doesn't seem to be any rhyme or reason for when it works. At this point I'm thinking I'll pick up a used Titan or Vogue on eBay and junk this thing.
Did you try a different rom ? Could be a faulty rom.
I've tried several different roms, yes.
this happens in some roms...
go2 wireless lan settings and then go2 power mode.change it to best perfomance frm best battery
Related
I have done hard reset and soft resets and still my wifi is not connecting.
Finally my EDGE is working great but wifi not. Whenever I try to connect my SSID is set to "EMC Wireless Internal" channel 11. I have no idea where this cam from but I can not get rid of it. I have a new FIOS Actiontec router with wireless enabled to my network name, channel 10. And Hitchhiker tries to connect but it keeps getting bumped off.
I have gone into MediaNet and turned off the proxy and checked for it to go onto the internet on Cingular GPRS.
I have not had a problem connecting before on wifi. I wonder if the router is a problem here, or if my phone settings are screwed up.
And ideas?
Thanks
The WiFi - EDGE contengency
*The Bad News*
By default, if EDGE/GPRS is configured to work, WiFi is rendered useless.
You didnt mention what carrier you have. I have Cingular and they even state on there website that If you configure the Edge/GRPS to connect, then WiFi may not work.
*The Good news*
I have my 8125 working with both Edge and WiFi. Heres what I did:
1. Open Connnections and click on the 'ADVANCED' tab.
2. Click on 'SELECT NETWORKS'.
3. The top pull down should be set to 'MY ISP' or, if you have named your WiFi connection something different, select it here.
4. Click 'EDIT' under this pull down and set connection to 'AUTO PICK'. 'OK' back to Network Management screen.
5. The bottom pull down should be set to 'MEDIA NE'T.
6. Click on 'EDIT' under this pull down. This is where you will set up EDGE using your carrier's settings.
7. 'OK' your way back out. Your done.
These settings let WiFi try to connect first. If no WiFi is available then EDGE/GPRS is used.
Good Luck!
Thank you! Worked for me, but videos streamed from orb still aren't working
Wierd-Fi
I also have WiFi problems after installing HTC official upgrade
ROM 2.25.11.1 WWE
Date 5/11/06
Radio 02.25.11
Protocol 4.1.13.12
ExtROM 2.25.11.102
Everything is great except after successful connection to home WiFi it disconnects after maybe 5 to 15 seconds ... network becomes "unavailable" .. no error message. This happens even when not connected to CIngular EDGE/GPRS (flight mode ON then, individually enable WiFi ON for what that's worth). When I delete my home network WiFi entry to force a re-recognition and setup, it recognizes the wireless net just fine (again) but same behavior.
All my settings are already set as suggested by ralugniC8125 in this thread. I had not tried any of the other ROMs with added features/hacks/fixes found on this website ... would any of them behave differently, you think? PHone was bought from Cingular .. I have not done any unlock procedure (don't really need to from a service standpoint but will if necessary to make a new ROM work right).
Any thoughts appreciated...
tskelton said:
Everything is great except after successful connection to home WiFi it disconnects after maybe 5 to 15 seconds ... network becomes "unavailable" .. no error message.
Click to expand...
Click to collapse
I have just purchased an unlocked Tilt from eBay. I have been scanning the wiki for days now, along with other sources, and to no avail. I still cannot get my WiFi to work properly. If any one has had this issue and has found a solution, I would love to know it!
ok, here's a suggestion since none of you have mentioned it.
Diable the MAC (Media Access Control) Binding on the router. This should help.
Maybe yall can help me now I have it attempting to connect however it only connects to gprs and it even shows it has a great wifi signal
Still Wifi-less and Woeful
lobotomy said:
Diable the MAC (Media Access Control) Binding on the router. This should help.
Click to expand...
Click to collapse
Thanks for the suggestion. This did not help unfortunately. I should mention that I have tried to access several different types of routers... with and without security, and while they are showing up as being available, they will not stay connected for more than a second or two.
Any other possibilities?
I'm really racking my brain on this one. I would greatly appreciate any ideas, as I've long run out of them.
---Intro---
I have a one week old Wizard (Cingular 8125 variant). It has one of the latest roms with AKU2 on it. Using Registry Wizard, I selected the option to add wireless G compatibility at some point in time. Wireless initially worked after setting my phone and router up per a tutorial on a popular Axim users forum. A day or two later I went to use WIFI and I get nothing. GPRS/EDGE initially worked also, but at the same time it stopped working. I've spent countless hours since trying everything I possibly can to get WIFI to work.
---The problem---
I am not able to connect to the wireless router. My Wizard sits on "connecting" forever then maybe 5 mins later it says unable to obtain an IP address. When I look at the status, it says 0.0.0.0 for the IP address the whole time it says connecting. Since the problem started, I have yet to actually connect using any settings. The first day I configured the wireless it worked perfectly, with WAP encryption and all.
---Some of what I have tried---
On my US Robotics wireless router I've turned mac filtering and all security settings off, making an open network. I removed the WAP setting for the connection on the Wizard as well. I've tried all the suggestions I can find on any WM 5 and 2003se related forums to no avail. I've tried all the various combinations of limiting to B/G only or mixed, using work/internet settings, and deleting WIFI connections and creating new ones. I don't have a proxy setting in any of my connections. The whole time my battery usage is set to the highest (performance) setting and I'm right next to the wireless router. I've tried turning off all proprietary speed enhancement options. I even installed a program (Pocket DHCP) recommended by Axim PPC users to figure out why I'm not receiving an IP. Since I'm not really a DHCP wiz, I can't tell from the results what is causing this.
I'd be greatful if anyone can help me with figuring this one out. Thanks in advance!
maybe a dumb question, but...the wireless part of the router is working fine? did u tryed with a laptop or pc?
did u tried a hard reset?
That's actually a great question. I did connect fine the first day I configured the wireless and made no changes from then until it stopped working, so I'm just assuming that the router is working properly. Unfortunately I don't have access to any other wireless device/laptop to test it with.
I'm getting ready to do a hard reset right now. I was really wanting to avoid this but I think I have no other option. Hopefully this will fix whatever setting was messed up. I have a slight hunch that the registry change for allowing G access was the cause of the problems.
maybe i missed this in the original post, but have you tried making your device use static ip's on the lan instead of dhcp?
Shogunmark:
I didn't try static IP's for two reasons. 1. Firstly I couldn't figure out how to set this up. 2. I don't want to have to fiddle with removing the static IP when I'm away from home trying to use a different wifi hotspot. I would like it to be seamless and just connect when I turn wifi on near any unsecured network (other than the usual pressing OK to connect).
STATUS UPDATE:
I did a hard reset and directly after this I tried to connect to my open network. Amazingly GPRS/EDGE now works, but WIFI still does not. Then I did a factory reset on my USR router then changed the settings back to how it was just set before. Now, I'm connecting. This doesn't make any sense since the settings are the same now but it's working, maybe theres a glitch with the router that this fixed. This small progress seams like a miracle.
Now that I can connect to WI-FI, I have a new problem. When I try to load pages in internet explorer, it says page not found or whatever the standard error message is. I'm so close I can smell it. There must be some setting that needs to be changed on my Wizard.
SUCCESS
I report that I am now absolutely delighted with network connection on my Wizard. After hard reseting the phone and the router, now I can connect to both WIFI and GPRS. Not only that... but also PIE will choose WIFI if I'm connected to a wireless router, otherwise it will default to GPRS/EDGE without any interaction from me. This stuff is really awesome when it works. It is difficult to setup correctly though.
somehow wifi routers r not 100% reliable, every now and then i need to reset my linksys or i cant get ip as in your case...but with a normal reset is enough in my case...
That's good to know. Maybe I didn't even need to hard reset my Wizard, just the router. Now I know to start with the router because it's much easier to reconfigure. This is the first time that I've implemented WIFI on my own network. What happens if a public WIFI spot won't give you an IP anymore? Surely you just can't go and reset it. Granted it's not nearly as old as Ethernet, WIFI has been out for long enough that you think they would have these major kinks worked out.
Nicnatros said:
... but also PIE will choose WIFI if I'm connected to a wireless router, otherwise it will default to GPRS/EDGE without any interaction from me.
Click to expand...
Click to collapse
How did you manage this? I have been struggling for ages to set things up this way. Can you post your settings from settings>connections>connections>advanced>select networks. Also settings>connections>network cards.
I would like to be able to just turn on wlan from comm manager and use wifi to surf and connect to my wireless lan, but if no wifi available to default to my T-mobile gprs connection for surfing. Currently having to manually change the settings "Programs that automatically connect to the Internet should connect using" My Work Network or Tmobile gprs each time I want to use either.
What I want is the option
if wifi available
use wifi
else use gprs
Well my friends and I were like sitting around drinking foo-foo drinks and I just like stumbled upon the answer. Just kidding, it's fun to play the role of your avatar, especially mine.
Settings, Connections tab, Network Cards, Network Adapters tab: My network card connects to Internet
Settings, Connections tab, Connections, Advanced tab, Select Networks: Set first one to My work network. Set second one to MediaNet (or your gprs/edge/etc connection profile).
Now with those set, edit the My Work Network profile and make sure that under the proxy tab check connects to the internet option, uncheck the proxy option. Now edit your MediaNet (or other carrier data plan) and make sure that this contains all options for your carrier like proxy, modem, etc. If you are a Cingular user, go here to verify all settings for medianet. (Note that you will ignore the beginning couple steps when they say to place medianet first in the "select networks" settings. Start after step 6. Also they used the CingularGPRS connection profile instead of the MediaNet one) http://www.pocketpcaddict.com/forum...ular-8125-windows-mobile-5-phone-edition.html
When you connect to your WIFI router first and it asks you if it's work or internet, always select internet. If you are not sure what it's set at, go out of range or unplug your router. Go into network cards and find your router SID, click and hold on it and select remove. Then when you try to connect to your WIFI again it will prompt you for this, make sure you use internet setting.
Now if you have done everything correctly, Internet Explorer will use WIFI when it's turned on and you get a connection. All other times it will default to GPRS/EDGE. I can go from one to the other back and forth without changing any settings, only enabling and disabling WIFI in the comm manager.
Trashman said:
somehow wifi routers r not 100% reliable, every now and then i need to reset my linksys or i cant get ip as in your case...but with a normal reset is enough in my case...
Click to expand...
Click to collapse
Linksys WRT54Gx? if yes look into dd-wrt . stable and has a lot of features . other hardware is supported as well just check on their webby.
yaboc said:
Linksys WRT54Gx? if yes look into dd-wrt . stable and has a lot of features . other hardware is supported as well just check on their webby.
Click to expand...
Click to collapse
I have read many many many posts about people having issues with the wizard and that exact router... I personally would stay away from linksys.. i work in a field that deal with 3rd party routers and such, anytime an end user has a linksys i can usually prove 90% of the time that its the culprit (80% of the time powercycling it does the trick)
Nicnatros said:
Go into network cards and find your router SID, click and hold on it and select remove. Then when you try to connect to your WIFI again it will prompt you for this, make sure you use internet setting.
Now if you have done everything correctly, Internet Explorer will use WIFI when it's turned on and you get a connection. All other times it will default to GPRS/EDGE. I can go from one to the other back and forth without changing any settings, only enabling and disabling WIFI in the comm manager.
Click to expand...
Click to collapse
This seemed to do the trick for me.
I am sure that I had tried all possible combinations previously but what the hell, it is working exactly how I want now.
Thank you
Hi guys. If you don't remember me - here's my story in a nutshell. I got a 8525 about a week ago. Since day one I tried and tried and tried but never managed to get the wifi working... (as you can imagine I am beyond desperate at this point)
Anyway last night I got thinking and decided to give it another stab. I hard reset, messed with the settings again...and this time manage to get a little further. My phone is now showing me as "connect to network", only problem is I get a message saying "Cannot connect with current connection settings. To change connection settings, tap Settings." each time I try to access anything internet related. I know I'm close especially since I'm actually connected now, I think it's just AT&T's rom doing everything it can to get me to use their networks (I'm on T-Mobile and don't have a dataplan anyway...).
Anyway can you guys think of what the problem might be? I'm so close I can taste it! Thanks.....
Bump... Anyone home?
where did you get your 8525? my wifi on my 8525 works perfectly fine, have u tried upgrading to WM6?
I have WM6 already. I got it off ebay. Everything is perfectly fine with it, it just doesn't want to use the wifi connection to get online.
Try a hard rest.
my 1st 8525 i got off ebay, and it worked great up until a few weeks ago, when the screen stopped functioning it just turned white, i called AT&T and they sent me a new 1 i just got it this morning and now, i cant make calls >.> it will ring then my phone will say i have no service when i have full service and the call will end. but my wifi is fine... did u use the WM6 upgrade that was released by AT&T
No thanks re: the hard reset. I've already done that... If I can't figure this out I'm going to sell my phone and steer clear of ppc phones. I like it, but I bought it for wifi and this is just getting ridiculous. I have tried everything. I've spent hours and hours on this. I've reset my router god knows how many times, played with security settings, reset my phone over and over to start over.....
The worst part now is that I know it's connected. The wifi aspect is fine. It's just the stupid phone not wanting to use the wifi connection for the internet.
Maybe someone with a 8525 and a Linksys router can post ALL of their wireless related settings for me.
Ekh
Yes I used the AT&T update.....
i use wifi and my linksys router, the 8525's range isnt that great u need to be within a few feet of the router to get good reception, im about 30 feet from mine and i get 2 Wifi signal bars and an ok speed. but try this
Start > Programs > Proxy Manager > Disable Proxy
then try to use your wifi, then go back and restore the proxy when your done, i think some 1 told me to do that because att uses that so u can use their internet service or sumthin
Thanks but I'm way ahead of you. I've already tried every piece of advice I've come across on xda. My last hope is someone elses detailed settings.
is your network passworded by a WEP or TKIP ?
It's WPA... My device has the password, and I added the MAC to my router table. It's connecting to the router/wifi...
...it's just that my device won't use the connection
* Sigh * Looks like another one of my please help me posts has gone dead...again...
olly666 said:
...it's just that my device won't use the connection
Click to expand...
Click to collapse
Your problem may be one of the following:
1. The wifi connection is specified as connecting to "work" and programs are set to use an internet connection.
2. The wifi connection is specified as connecting to "internet" and programs are set to use a work connection.
Nope that's not it. But it does remind me of something so thanks. I deleted all the connections seeing as I don't have a dataplan... I made a new connection called "Wifi". BUT, it's not like I can specify any connection for it so it's just blank (no connection specified). By this I mean the options for a connection are:
bluetooth, cellular line, cellular line (GPRS, 3G), Generic IrDA, Hanes...COM1. No option for wireless...
Does that help?
Check that your router is set to allow connections by devices with 802.11b, which the Hermes uses. Most default to 802.11g only.
It's set for b and g
Helloooo...?
Hallelujah!!!!!
People, I have WIFI!!!
Thanks to everyone who tried to give a helping hand... It's really appreciated.
For future reference to those who are suffering from the same problem - this is what seemed to fix it... I entered google into IE via it's IP address rather than it's name (open command prompt, ping google.com...). To my surprise the page quickly loaded. I then instantly realized that the problem was with the DNS settings. I opened up "Wi-Fi" in settings, went to the "Network Adapters" tab at the bottom and entered in the DNS addresses for "IEEE 802.11b/g...". If you need help with this just PM me (I consider myself somewhat of an expert on this topic now).
I thought I was never going to get online. There IS a god!
Does anyone else have this problem?
My home WLAN is hidden, it doesn't broadcast it's SSID. I've never had a problem until maybe the last week. Now my phone won't connect to my WLAN (or any other hidden WLAN that I had connected) until I reboot my phone. Once I reboot BAM it connects right away.
In all likelihood it might have something to do with my custom rom. Guess I should get cracking on a v3 with the latest OTA anyway...
I had this exact same issue a while back I while using a flipz rom.. one version of flipz it connected to my hidden network no problem the next minute it refused to connect I never got an answer so I just gave up
hopefully someone can shed some light on this because it has been bothering me for a very long time
I don't know about routers that have WLAN configured on hidden mode, but don't you guys have an internet provider service for your home and could maybe work if you tried looking for your/their router provided Homepage Login details on Connections/Frequencies/Settings? I don't know much to say but this is maybe an idea, because I had a router with SBCGlobal Internet Services from AT&T on my home lines and we have the top tier DSL service including hidden lines for using the internet as in internet ip addresses, so I'm just saying I could connect with the key included but I don't necessarily have your problem per say, maybe it could be the router or WLAN itself to be reset settings on it for a reboot maybe and it might work, maybe not.
Sorry if my reply fails. I thought of this upon thinking from myself in my head.
I use my own router, not something provided from the ISP. The same thing happened with my father's router over the Thanksgiving holiday. I connected to his network fine after I configured it, but the next time it wouldn't detect it. It's definitely the phone. Guess Jiminy v2 isn't perfect Back to the drawing board!
Hi, I recently bought a 16Gb DVP on WinMo7 and for three weeks had no Wifi problems at all. It recently stopped finding my home WiFi router.It finds both neigbours routers but mine is missing from the list.
I then got an update notification for the Mango update which I competed. the router didn't return in my list of networks immediately but about two days after.
It has now dissapeared again but 'Mango' has the added 'Advanced' button to see 'known neworks'. My home router is in this lst but I cant access the settings or force any paring.
I've tried the obvious of turning it off and on. I've reset my router, reset my phone back to a clean boot of windos 7.5 (mango) and still no results for finding my router. All the other phones in the house and all laptops find it fine so I can only presume it is the DVP.
Details:
OS version - 7.10.7720.68
Firmware Version - 2250.1800.7720.219
Don't know if this helps.
Does anyone hav any idea why and what I can do to resolve it.
thanks
Jock
Try changing the SSID (name of your wireless network) to something else and see if your DVP can see it and make sure the SSID is not hidden.
Thanks, tried that last night. No luck I'm afraid.
On the router admin now and It's all as it should be fom my service provider settings.
I have a full signal of my neighbours router and just don't understand why it's chosen mine to not even find. When it appeared last time it was after turning the router off all night. I tried that again last night but it didn't appear this morning when I turned it back on.
Confused !!!
Jock
have you been able to connect to and maintain future connections to other wireless networks? if the same problems happens with other networks, I'd run a factory restore on your phone as it seems there might be a software issue. However if you can connect and then are able to re-establish a Wifi connection to other networks then I'm stumped!
I've just changed the SSID to something completely different and it's appeared and I'm now connected again.
All I can say is that it connects to the router for around a week and then the network dissapears.
Short of changing the name every 7-10 days I can't really see another resolve.
In answer to your other question, I haven't really used it on other networks.
I'll see how it goes with this new name.
Thanks for all your help and suggestions
Jock
After reading other posts, this might be an issue with the .219 firmware that you are on. Just keep checking for updates. You could try a hard reset of the phone and then a reboot of the router
Also make sure your router is set to either B or G mode. Check my post here: http://forum.xda-developers.com/showthread.php?t=1324949
Thanks, I did a hard reset when it first went off, still found nothing when it re-booted. I'll keep an eye out for the firmware update.
Thanks again.
My phone just started doing this as well. Very frustrating as I cant download large updates and I dont want to exceed my data cap. I am totally fed up with this phone!
Fixed. Called Dell. Long press network name. Press delete. Press network name when it shows again. Reenter password. Works!