My Artemis is coming only to the splash screen (orange) and than is stooping. Is it bricked, since I tried to upgrade the new software??
Thanks
unfortunatly yes... may be...
Hi,
I had the same Problem wirth MDA C3 and this one was bricked... But i don´t tried to start the bootloader mode (on/off + speech-dial hardware button together and than the softreset button, hold the other two buttons and press only short the softreset button)
May be than you should be able to flash it once more... However, i read this tip to late, i changed my divece before so i can´t garantee that it works....
But give him a try, it´s worth the time !!
regadrs,
andi
u'll find it in the forums somewhere, u just need to flash it with a new ROM (and USPL if it isn't the original ROM) This can be done from Bootloader as suggested by Mr.Trader.
rilazi said:
My Artemis is coming only to the splash screen (orange) and than is stooping. Is it bricked, since I tried to upgrade the new software??
Thanks
Click to expand...
Click to collapse
obtain the original rom for your device and flash it. it should be all fine.
after, install uspl, and then you flash with any rom again.
regards,
Related
anymore. :--(
Yesterday i^ve make a setup for the ext_rom but with a wrong update. It was been not for the Artemis..my fault.
Now i see only th et-mobile start screen and no more.
What can i do? Thanks in advance..
hmm, please flash your p3300 whith the original software with hope that it will be alive again. otherwise you can take an hardreset on your phone but i'm sure that there will not happened.
is your PDA an original fom HTC or from any other Provider?
it`s from t-mobile
and a hardreset doesn`t work and it`s not successful.
How can i flash it again...how i get usb connection to do it?
dr.moppi said:
and a hardreset doesn`t work and it`s not successful.
How can i flash it again...how i get usb connection to do it?
Click to expand...
Click to collapse
hello there!. i have the same problem, did you manage to get a usb connection? i can't flash it...
Try to get it into bootloader ( Read the Artemis wiki as to how to get into bootloader) and if you are successful then try flashing it with the t-mobile stock rom.
arvind09 said:
Try to get it into bootloader ( Read the Artemis wiki as to how to get into bootloader) and if you are successful then try flashing it with the t-mobile stock rom.
Click to expand...
Click to collapse
Please tell me how can i get the t-mobile stock rom or can you give me the link, thanks
Shipped ROM's in English - http://wiki.xda-developers.com/index.php?pagename=Artemis_Upgrades
To get into bootloader - hold down the record/voice command button (top left along the side of the phone) and use the stylus to press the recessed reset button on the lower left side of the phone (same side as the other boutton you hold down) Keep holding the record button as you hit and release the reset button, you will eventually see a screen with color bars on it. At this point you will be able to get a USB connection, but not an active sync. Try to start the ROM file when the phone is in this state and connected to your computer.
What is the original language/carrier for your phone?
MDA Compact III stops in T-mobile logo screen
I manage to enter bootloader and start flashing a ROM but I allways get a error: image file corrupted.
I think I need the original Dutch T-mobile ROM.
Anyone know where to find it?
Hi I have the same problem. I have the B&B3.7 and get stuck in the splash screen. I could enter to the bootloader mode and use some commands of the mtty.
I have my old rom, how may i load it to the pda? I have a SD and a tytn to load something in it.
Thanks!
Hernan
ftsv said:
I manage to enter bootloader and start flashing a ROM but I allways get a error: image file corrupted.
I think I need the original Dutch T-mobile ROM.
Anyone know where to find it?
Click to expand...
Click to collapse
run uspl first!!! you can then run installation from any provider of your choice.
http://forum.xda-developers.com/showthread.php?t=311403
USPL cannot be run if your phone is stuck into bootloader?
It starts counting, askts to copy the same information again several times, and get stuck at 50... how is this possible, anyone has the original HTC Dutch rom ? May be the WM5 also! Thanks!
same problem but with no display
i have done the same mistake
have tried to upgrade my T-MOBILE MDA COMPACT III(aka htc p3300) with the HTC TOUCH ROM
it started to upgrade and an error occured
then i have lost the display and all
when i connect it to my laptop using USB i hear a beep in my computer but active syn didnt find any device
i dont know what to do now..please help me it has to be recovered
there must be some way pls pls anyone help me to get my working phone back
will appreciate your concern
thanks
Regards
Faraz Feroz
well you have to get the original ROM for your device.. see their website.. it should be there for free. or try to get it from anyplace.. (the original rom)
and then flash it using SD Card flashing
info for flashing it by that are here:
http://wiki.xda-developers.com/index.php?pagename=Artemis_SD_Card_Flashing
hope it will work
y_bother said:
well you have to get the original ROM for your device.. see their website.. it should be there for free. or try to get it from anyplace.. (the original rom)
and then flash it using SD Card flashing
info for flashing it by that are here:
http://wiki.xda-developers.com/index.php?pagename=Artemis_SD_Card_Flashing
hope it will work
Click to expand...
Click to collapse
thanks Y_Brother
i have downloaded the new rom but it doesnt seem to work too
Hi people,
I have a mayor problem. I just fu*ked up my phone by installing WM6.
Now the screen freezes when the QTEK "Keep the world in one" logo is visible with the OS Version information. Hard reset wont work.
How can I restore the original rom ?
Please help me!
s200 off
and I have this problem. my phone is off by installing new spl
Now the screen freezes when the QTEK "Keep the world in one" logo is visible with the OS Version information. Hard reset wont work.
How can I restore the original rom ?
Please help me
To go in the boot loader screen you have to:
press & hold camera and commmanager button
press the softreset hole
release the commmanager button and keep hold the camera button until the 3 colours display appear
Byez
but wat can i do after i hav the 3 colour screen come out?
pls help..... i'm very nervous..... i don wanna waste my money coz i screw up my phone.,...
i'm now outstation... can go back to the service center within this 6 mth....
Connect USB Cable. Go in the Boot Loader screen (Hold down camera button, power button and soft reset until the 3 colours display appear). Run Rom upgrade Software.
mrsurya2000 said:
Connect USB Cable. Go in the Boot Loader screen (Hold down camera button, power button and soft reset until the 3 colours display appear). Run Rom upgrade Software.
Click to expand...
Click to collapse
Which rom upgrade software ?
de.schurk said:
Which rom upgrade software ?
Click to expand...
Click to collapse
http://www.romupdate.ru/ghjibdrblkz...rophet_220734_2207114_024721_QtekWWE_Ship.exe --> this software
don't worry, your device isn't bricked as long as you can run it in bootloader
check in WIKI if you have G3 or G4 Prophet
I'm the exact same situation.
And wiki didn't help so far...
Take it easy and flash the ROM as described. Use any WM5 ROM compatible with your device, but preferrably one with no vendor ID. In case you cannot update normally use the RUU-No-Vendor-ID application found in the FTP.
As said above the device is not dead, it can be recovered.
namco said:
Take it easy and flash the ROM as described. Use any WM5 ROM compatible with your device, but preferrably one with no vendor ID. In case you cannot update normally use the RUU-No-Vendor-ID application found in the FTP.
As said above the device is not dead, it can be recovered.
Click to expand...
Click to collapse
Bear with me on the dumb questions
It looks like I managed to re-install
Thank you for your help. I installed the rom dezzer advised (post 7 of this thread) and it worked fine. Does that mean tha NOW i can flash smart1 1.3's?
Yep. Turn off the phone, make it sync with activesync and run UPDATE_ROM.bat.
Then cross your fingers Kidding. It will surely work. Remember to hard-reset after the upgrade.
If anything goes wrong just reflash WM5 and hard-reset. Always hard-reset after ANY OS upgrade.
hi all ..
I did flash my HTC wizard with new rom after finishing the install the device reboot and stacked on the boot screen then I tried to go to the boot screen but I couldn't , I tried to make hard rest but also I coudn't nothing is working even charing the device cant be made .
bye bye
Are you able to get to a multi-colored screen with numbers?
In case you don't know, to get to the bootloader screen hold down the camera button and press the power button.
now i got the same problem.
I updated the rom & now i have the multi-colored (red/green/blue/white) screen
with RUU - IPL 2.18 - SPL 2.18 - USB on it (Qtek 9100)
I downloaded the tools from Vippie in the thread "How to flash a new ROM to your Wizard... a little tutorial!" but those won't help...
anybody got any advice? I would like to install WM6...
thanks in advance!
Hello,
i have flashed my device new with the german touch it final rom from tije, which worked wonderful for me installing it first time (a month ago)
now i have flashed the rom again yesterday and my device stucks in the htc startscreen. nothing works (hardreset, softreset, removing battery)
please tell me what to do
Go into bootloader mode and flash with the german RUU (see Wiki and search for Details)
Then you can flash again.
thank you very much, this is the only thing i do not know (how to go to bootloader) but if it stands in the wiki, its all ok
ok what you need to do is hold the camera key and then hit the reset button... thatwill put you in boot loader
zacwhite15 said:
ok what you need to do is hold the camera key and then hit the reset button... thatwill put you in boot loader
Click to expand...
Click to collapse
sorry camera and reset worked thanks
but how can i flash my new rom now? i just checked the touch it final german rom from itje and i got the following message: no device connected - would you like to try copying again?
can i flash with official rom? how? i need active sync right?
ok everythings ok right now will flash with official htc wm6 now (works without active sync)
and then i will start again with itjes touch it rom, cause i know it works stable
EDIT: EVERYTHING WORKED FOR ME NOW, THIS IS HOW I LIKE IT ^^
After I have installed the maatiROM.V3 ROM, my phone has not been able to boot into Windows properly.
It booted into Windows the first time after I installed the ROM, however, when I tried to restore the programs and reset the device, it tries to install the ROM automatically again, however, after its all done and reset, it holds on a white screen with the HTC logo.
Can someone please give me some advice?
Download youre Original rom for youre device. and get the Leo in 3 colour screen then connect the usb and flash the Original rom back.. than it must work.
Jowan073db said:
Download youre Original rom for youre device. and get the Leo in 3 colour screen then connect the usb and flash the Original rom back.. than it must work.
Click to expand...
Click to collapse
my original version is 1.48.831.0 (71294) WWE
but I couldn't find it
I have version RUU_Leo_HKCSL_CHT_1.48.832.1_Radio_Signed_15.28.50.07U_2.05.51.05_2_Ship
but I dont know I need to use SSPL to install it or not....
I try to use SSPL to install it, but error [294] occur.....
WHAT CAN I DO???
thanks!!
kayzee said:
my original version is 1.48.831.0 (71294) WWE
but I couldn't find it
I have version RUU_Leo_HKCSL_CHT_1.48.832.1_Radio_Signed_15.28.50.07U_2.05.51.05_2_Ship
but I dont know I need to use SSPL to install it or not....
I try to use SSPL to install it, but error [294] occur.....
WHAT CAN I DO???
thanks!!
Click to expand...
Click to collapse
Just download it from HTC support site... no need to use SSPL for this as it is the original ROM...
kurniawan77 said:
Just download it from HTC support site... no need to use SSPL for this as it is the original ROM...
Click to expand...
Click to collapse
I am come from Hong Kong
Hong Kong's HTC website no download link.....
I dont know which version should I install
I got two version now
one is Official WM6.5 ROM - HTC HD2 (Leo) - English Asian Version(1.48.707.2)
the other is Leo_HKCSL_CHT_1.48.832.1-this is a chinese version which released by CSL (CSL is the provider which sell the phone to me, but my original rom is 1.48.831.0 (71294) WWE(English))
so I am very confuse now...
dont know which one is suitable....
Any idea??
thanks thanks thanks thanks so so much!!
I tried to install both official english and CSL chinese version, its show error [294].......
What should I do??????
now, the phone can get into windows(maatiROM.V3 ROM),but the phone keeping crash...and I reset it....the phone will re-install the windows(maatiROM.V3 ROM) again.... then crash again, and I reset again, and the phone re-install again.....keeping repeat crash, and I reset it, and re-install windows.......
*CRYING*
I dont know what can I do now.........
In my opinion you can try the folowing:
- Remove sim and memory card and do a hard reset (with phone off , keep holding down the volume up and volume down keys and press power button, release all butons then press volume up again to restore manufacrurer deaults)
- Try to enter in boot mode (with phone off , keep holding the volume down and press power button) then flah again your phone
- If none of these helps and you can't find the original rom then use the GOLDCARD method. So make yourself a goldcard (serch the forum and you will find how to do that), boot your phone into flash mode with goldcard inside and you will be able to flash any original rom to your device
WBR
golumbu
golumbu said:
In my opinion you can try the folowing:
- Remove sim and memory card and do a hard reset (with phone off , keep holding down the volume up and volume down keys and press power button, release all butons then press volume up again to restore manufacrurer deaults)
- Try to enter in boot mode (with phone off , keep holding the volume down and press power button) then flah again your phone
- If none of these helps and you can't find the original rom then use the GOLDCARD method. So make yourself a goldcard (serch the forum and you will find how to do that), boot your phone into flash mode with goldcard inside and you will be able to flash any original rom to your device
WBR
golumbu
Click to expand...
Click to collapse
Thanks!!!I restored the phone to manufacurer default!Seems to be ok!!
thanks so much!!!
I
kayzee said:
Thanks!!!I restored the phone to manufacurer default!Seems to be ok!!
thanks so much!!!
I
Click to expand...
Click to collapse
It happened to me and I found out it is one of the reg tweaks in combination of a cab I installed did not work with maatiROM. The rom itself is stable and I use the Premium, which version did you use?
sakiin said:
It happened to me and I found out it is one of the reg tweaks in combination of a cab I installed did not work with maatiROM. The rom itself is stable and I use the Premium, which version did you use?
Click to expand...
Click to collapse
same as you!!!
I am using premium.....