Hi there!
The original shipped CINGULAR WM5 ROM is KITL enabled.
My 8525 is flashed with the O2 GERMANY WM6 ROM which does not have KITL. I shortly gave it a try and extracted IPL / SPL from the Cingular ROM and flashed it to my 8525 in the hope that would KITL enable my device but it did not!
Does anybody know how to 'add KITL capabilities' to a non KTL ROM? Where is the KITL stuff located in the ROM? It does not seem to be in the bootloader otherwise I should have been able to get it by loading the bootloader from the CINGULAR ROM.
Related
Hello There,
I've spend my free Sunday on flashing my ROM :roll:
I wanted to warn about a "bug" in the t-mobile 4.01.16 ROM with o2 radio 4.21. Here’s what happened:
I've upgraded from AT&T a.30.09 ROM with o2 Radio 4.08 to t-mobile 4.01.16 ROM with o2 radio 4.21.
- 1st I've installed the t-mobile ROM (SD Flash method Note: ALWAYS DO
THIS!)
- 2nd I've turned off my phone and installed o2 radio 4.21 (through
programB)
Problem:
Every thing went well and there were no errors at all! But:
When I tried to start my phone again there was NO SERVICE possible?!
- I've tried to reset my GSM Module by going to the Wallaby bootloader
V 5.14 and pressed the Calendar hardware button. This wouldn’t work.
- I've Flashed the ROM back to the original ppc 2002 ROM (Not the Radio
stack) to get my phone software back (what was lost or unable to start?!)
- Still the phone says no service possible!
- I've Downloaded the T-Mobile Radio stack 6.24.00 and installed it (by
Copying the RSUpdate.exe and files in the windows directory and run it
from the device windows directory).
- After doing this I had a white screen Hang . Luckily after a soft reset it
got back to the radiostack upgrade screen :lol:.
- But Still No Luck so far.
- I've reset my GSM Module again by going to the Wallaby
Bootloader V 5.14 and pressed the Calendar hardware button.
- Turned my device back on and got a simlock warning in W2003!?
- Had to Flash my ROM back again to o2 3.17.03 ROM PPC2002 to be able
to release my SIMlock again With XDAunlock. (worked :wink
- Still no Service !
- I've Installed the new o2 radio stack 4.21 back and
I had Service again!? :lol: :wink:.
- Upgraded the ROM again with T-Mobiles new 4.01.16 ROM.
- Finally it's Upgraded and smooth Working again!!! 8)
HERE IS THE CLUE!:
- I think It had to do with the o2 radio stack upgrade that came in conflict
with T-Mobiles new 4.01.16 ROM.
- So 1st upgrade radio stack in PPC 2002 OS if you have an older radio
(i.a. 4.08) stack before you do a ROM upgrade.
- WARNING: Don't use the T-Mobile band switch 900/1900 function if the
phone is working!!! I found this is also a crucial bug and causes to crash
the GSM module with the o2 4.21 radiostack!
Question: Could annyone tell me were I can find and how I can Upgrade
my Wallaby Bootloader from v5.14 to ........
Thanks and have a good one!
I have new ROM WM 2003 4.01.16.Is this stable one?While installing exe file it shows current ROM and Upgrading ROM 3.16 How is that?I have downloaded 4.01.16.Is there anything wrong
This is just a header string, it doesn't matter and it will not be shown in the device info as long as you cooked the right ROM.
Some people reported issues in 4.01.16 but not that severe, but I think 4.01.00 is the most stable one.
Softrest Everytime after Upgrading WM 2003 4.01.16
I have sucessfuly Upgraded my Qtek 1010 with WM 2003 4.01.16 by Bootloader method Thanks to Biso007 for his help.But now when Qtek turns off after 3mins It doesnot switch on even after pressing Power Button i tied several times.Now i have to do Resest Everytime or uncheck the box for turning off the device.
Whats wrong what to do I miss calls now.
Can i reinstall the same ROM or any other
Hi...
I upgraded my qtek 9100 from OS version 1.6.7.1 to cingular 1.8.11.1
The problem is that now, the phone doesn't start... the splashscreen appeears, along with... IPL 2.17
SPL 2.21
GSM 02.07.10
OS 1.8.11.1
But doesn't get out from there...
Did a do anything wrong?
PLEASE help me?
Is there any solution or is it bye bye qtek?
maybe you flashed broken or wrong rom.
start your device in bootloader mode (look in wiki how to do this) and then reflash again and if this does not work, get rom from your provider and reflash with this.
...
But my pda starts and it stays in splashscreen... is it repareble anyway?
Yes it should be fixable
Cant understand why you would want a old cingular rom (the cingular is not exactly same hardware as your phone wiza200 vc wiza100!)
You should download an aku2 rom here ftp://xda:[email protected]/Wi...digy_2170702_21707102_20710_QTEK_WWE_Ship.exe
user name xda password xda
Next get into the bootloader screen - turn device off and start with camera button pressed - should be a multicolor screen
Next attach device to pc via usb cable
Flash with above rom and all should be well
ive got a htp 3300 from movistar spain and i allready got it unlocked, yesterday i put the wm6 english on it and today y tried to put
PDAMobiz_Dopod_P800W_AKU301_v1.1.2_PowerMap, now
i can see only the white htc screen
IPL 3.007.001
SPL 3.07.0000
GSM 02.69.90
OS 1.28.0.0
the phone dont start anymore
y need helpe please
Can you get in to the bootloader?
If you do then you can put an original rom back. If you don't then send it to the service.
An unlocked device is out of warranty so be prepared to pay for the service.
Go to wiki of Artemis there you can find the method to get in to the bootloader.
Goof luck! << you need that.
you meen push the record button and reset in the same time???
i tried this befor but never go in bootloader modus maybe i make something wrong pleas help me
As of this http://forum.xda-developers.com/showthread.php?t=308242#1 threath of meschle states your device is a brik.
I'm sorry to tell you that.
meschle said:
Do Not flash your Artemis with a different carrier/cooked Rom without cid unlocking
--------------------------------------------------------------------------------
Noobs beware!
As a number have been flashing their devices with various roms not from their own carrier or country or cooked roms and bricking their device - I put up this sticky. Your device must be cid unlocked first before you do this. This applies to the coming wm6 roms to - if the rom is not specific to your device - i.e. if you try to flash the upcoming htc 3300 wm6 rom on O2 orbit - you must cid unlock first - with imei check or you will end up with a BRICK!
This does not apply if you are only updating the os http://forum.xda-developers.com/showthread.php?t=299154 or radio.
cid = country id i.e. locked to that country/language/vendor
cid unlock for the artemis is here with USPL http://forum.xda-developers.com/showthread.php?t=311403 (thanks pof)
or here http://www.imei-check.com/c3unlock.php (costs though)
Bricked devices
If you have flashed your device and not cid unlocked it, your device maybe salvagable if you can get it into bootloader mode.
Hold down the voice speed dial button and soft reset - you should then enter bootloader mode 'multicolored' screen'
If you do, attach device to pc via usb cable (a small usb will appear bottom left of screen) and flash factory rom. (run rom executable or RUU updater from pc) You do not need to be activesynced to do this.
HTC P3300 WWE factory rom downloadable here http://rapidshare.com/files/19322112...0_WWE_SHIP.rar
Dopod P800 WWE factory rom downloadable here http://rapidshare.com/files/21058219...0_WWE_SHIP.rar
O2 Orbit WM5 WWE factory rom downloadable here http://rapidshare.com/files/41574866/Arteimg.nbh
O2 Orbit WM6 WWE factory rom downloadable here http://rapidshare.com/files/46377862....90_Shi p.exe
Before you flash again with a non-factory rom, your device MUST be cid unlocked.
If you cannot enter bootloader mode your bootloader has been damaged and your device will need to be sent away for repair.
Click to expand...
Click to collapse
movilstore said:
ive got a htp 3300 from movistar spain and i allready got it unlocked, yesterday i put the wm6 english on it and today y tried to put
PDAMobiz_Dopod_P800W_AKU301_v1.1.2_PowerMap, now
i can see only the white htc screen
IPL 3.007.001
SPL 3.07.0000
GSM 02.69.90
OS 1.28.0.0
the phone dont start anymore
y need helpe please
Click to expand...
Click to collapse
i had the same problem and took me 3 days to fix it. so maybe this will work for you too !
first take out the battery for 30 min then push the reset button and put the battery back and turn on the device. if this not working. try to start bootloader by pressing and holding the record button and on/off button and push the reset butoon in the same time but keep pressing the record button and on/off button till a colored screen shows up??? sometimes it doesn't appear at the first time so just keep trying .
if you have bootloader you can reflash a rom. but you need to format your memorystick first to fat on your pc then put the image rom (nbh file) and rename it to Arteimg.nbh !! i used OrbitO2UK image.
Hello,
I have flashed my MDA Vario with a WM6 rom dutch witch worked fine. After i changed my pagepool to 6 MB and soft rebooted my MDA, it stared, but without phone functionalty. every program i try to start it gives me the message that it has no memmory to start the program.
No activesync connection (or any other connection) can be established. I have found some articles on flashing xda pda's from sd card. But in these articles they talk about .NBH files. The only file i can find in the update util is an .NBF file. Can anyone help me solving this issue?
TNX in advance
Try bootloader mode?
Bijdehandje said:
Hello,
. . .
No activesync connection (or any other connection) can be established. I have found some articles on flashing xda pda's from sd card. But in these articles they talk about .NBH files. The only file i can find in the update util is an .NBF file. Can anyone help me solving this issue?
TNX in advance
Click to expand...
Click to collapse
Can you get into bootloader mode (tricolor RGB bands)? ("Get your phone in bootloader mode by doing this: Phone powered off, press Camera button + Power On, will enter into bootloader mode (RGB screen").
Once in bootloader mode you can reflash even though activesync says not connected - just look for little USB in corner of screen.
Tnx cushcalc for your reply.
I have tryed it just a minute ago. I can enter the boot loader but the flashing fails at starting with the message "This update utility cannot be used for your PDA Phone. Please get newer update utility". I have used the same flash tool as the rom image witch is now on the MDA.
Sounds more like CID locked after flashing the last ROM was flashed....cant u even flash any other wm6 ROM?
You should flash the original T. Mobile ROM from bootloader it should work. After you have the original running you can then re-flash WM6 using shelltool if your phone is CID locked. Try it and lets see how it goes.
You people are the greatest. I have tryed to flash my MDA Vario with the latest rom from t-mobile and now i have a fully functional mda again. BIG TNX for helping!!!