Related
Hi Friends,
My new mobile phone SPV M600 got stuck whil starting showing four lines of messages as shown below.
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 2.10.1.22
Can any one please help me in geting my phone to today's screen.
I also attached the screen shot for reference.
did you try a hard reset ?
Ya I tried both hard as well as soft reset but same screen is stuck again and agian.Can any one please help me in this regard as I am very new to PDA family.
Ok, first things first:
Since you are new to this, are you sure you preformed a hard reset?
It is done by holding power + camera + comm manager buttons (one on the right, two on the left) and pressing with stylus in the reset hole at the same time.
A message should appear asking you to press 'send' (green phone button) to confirm reset.
If this does not help, you may have a serious problem.
Please answer the following:
Is the device fully charged?
Phone will fail to boot if the battery is too low.
Did you install any software right before this happened?
This should have been resolved by hard reset, but just in case I am asking.
Did you change the ROM, attempted CID / SIM unlock?
This could require more serious measures than I can advise on.
I did exactly the same thing which you mentioned.But even then it is stuck at the same screen.
Ya u r right I unlocked my mobile using a software from eBay.The unlock was successfull and I tried to insert T-Mobile sim, it also captured the signal and I was able to make and recieve calls then after that I wantedly switched off the phone and then tried to start it, there got the problem.
Can any one help me in this regard please.
I am having the same problem, but my phone is not sim-locked.
I've got the same problem after attempting smart1_wm6_pp8mb.exe
I'm having the same problem with my G4 QTEK S200:
Attempted to upgrade to WM6 Rom using smart1_wm6_pp8mb.exe
After reboot the phone got stuck at the QTEK Screen
Tried Hard Reset (Camera+Power+Comm+Reset) followed the steps with the same results (bricked)
I also tried re-flashing the rom back to the factory one using RUU_Prophet_220734_2207114_024721_QtekWWE_Ship and ROMUpdateUtility-NoVendorID.exe in Windows Vista with WMDC (Windows Mobile Device Center v. 6.0.6873) and the phone in boot loader mode (tri color screen) with working USB cable, with windows firewall disabled and symantec AV disabled as well, RUU keeps saying error 260 "the update utilitiy cannot connect to your pda phone..." .
Do you think I should try this process using XP instead? No matter what i try i keep getting the error 260
Any help would be greatly appreciated
Got it fixed!
it was definately a Vista issue. once i tried it in XP with ActiveSync it worked like a charm and i got my phone back up and running. also used spb backup and restored all my settings.
ipl/spl screen
i got the same problem with new rom wm6, and the 260 eror, my problem is that i have xp and the activesync does`t connect ...
... means i cant redo the original rom ????
PLEAAASEEE HELPPPP !!
Again My phone SPV M600 got stuck at IPL/SPL screen
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
yekanth said:
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
Click to expand...
Click to collapse
A rom reinstall on xp solved my problems on that one. retry a couple of times! It may not work the first time! hard reset as well...
Try an official wm5 rom just in case
good luck
Can you please gimme step by step procedure
HI Phil,
I am new to these kind of installations . CAn you please Gimme step by step procedure for ROM installation.
mine is now also stuck, after trying to install new rom. wont connect to active sync either, have i fooked it? tried hard reset etc.
thanks
(with a turned off phone, press and hold camera button then insert USB cable)
then flash provider ROM
RECOVERING FROM ERROR IN STEP 8 WM5->WM6
1. Don't panic
2. Don't panic
3. Unplug the phone
4. Reset with stylus,and keep the Camera Button pressed.
5. A 3 color screen will appear(Bootloader Screen)
6. Connect your device with your PC,and run the NVID(no vendor) WM5 rom.
7. The device will be resetted after RUU(rom update utility)finishes
8. Repeat the WM6 upgrade,from STEP 5..
Click to expand...
Click to collapse
from here http://forum.xda-developers.com/showthread.php?t=310452
hi jay
i seen your post in n00b guys one, i fixed it!!!!, thank you so much, i couldnt remember how to get it to those 3 colours.
thanks again
Colin
Hi Iam unable to get the NVID ROM
Hi,
I am unable to get the NVID ROM. The Rapidshare link that has been provided in the other thread is not working. Can some one tell where can i get the ROM.
collywog19 said:
i seen your post ...
Click to expand...
Click to collapse
no problem mate.
..and yekanth i see what u mean about the dead links. i have the files on my computer at home but i'm posting from my prophet right now, so i can't upload. Try using the "pdaviet temp" from one of the wm6 threads?
(http://rapidshare.com/files/54265407/Prophet_PV_Temp.zip)
Hi Iam able to update the Rom but no use
Hi,
To mention my phone is from orange-UK. I got the orange rom from our FTP site and did the flashing/update what ever you say.But still it is getting stuck at the same IPL/SPL screen. Iam very much worried that I will not get a proper solution for my problem.It will be very grate full if some one resolve my problem.
just seems strange...how did you fix it last time? did it just start working again? A random guess would be that the camera button got liquid spilled on it or is stuck in.
If the camera button is pressed in the phone will go to 3 colour screen every time it is turned on.
It won't do any harm if you try to press/move that button to see if u can "unstick" it, not likely I think but u never know...
Need help!
I have been messing with this phone for afew days now can't seem to get it to work. When I power the phone on all I see on the screen is green screen that says "IU BUILD! Test Only" this ws the result of a hard reset. The device is sim unlocked but I don't believe it's super cid unlocked. I'm unable to do anything except for hard resets and bootloader screen. I was going to try to reflash the original rom but can't seem to find any, I only have access to the sp3 roms which I can't use since it's not super cid unlocked. Any help would be great!!!
iMate OEM ROM
http://rapidshare.com/files/61129896/SP3_WWE_2.4.33.11.zip
Here is a link to an iMate OEM ROM. Start in bootloader and execute this to see if you can recover your device. You haven't shared much about what you phone is or how it ended up like it is. You are correct that it needs an OEM ROM, then application unlocked then Super CID unlocker before flashing a custom ROM. Good Luck and report back you results.
The phone is a Krome IQ700. In bootloader mode it shows IPL 0.27 SPL 1.01.0109 Typhoon UI. Another problem is active sync does NOT see the phone. When attempting to load any rom I get error 264. I think I might have to load rom with SD the only proble is I've never had to do this before so any help would be great. I could honestly live w/o the phone but I think this would be a great learning expirence. Thanks in advance.
after attempting your reply my phone is now dead and will not power on ...
nwdrifter said:
after attempting your reply my phone is now dead and will not power on ...
Click to expand...
Click to collapse
Remove the battery and memory card, wait 30 minutes then re-insert the battery. Hold in the camera button and then plug in the USB. If it is still alive, it will open in bootloader (Red, Green, Blue) mode.
still dead... what do you think happened?
nwdrifter said:
still dead... what do you think happened?
Click to expand...
Click to collapse
I had this once when my oem battery died. I was able to jumpstart it and get it to recharge using a 9v battery to kick it up from nearly 0V.
If you have a battery meter, you can test the contacts, looking for 4v across the battery terminals (remove battery from phon to test). If you get < 2v then you battery does not have enouge juice to power up.
Once you get power back, do you have the ROM from your OEM? You should be searching for it in the mean time. If I find anything on it, I will let you know as well.
Everything I see on your phone specs appears that it should respond and behave like all of the other Typhoons/Sp3's. As long as you followed the unlocking steps from Karhoe's post (second sticky on typhoon main page), your device should not be a brick. If you recover power, you may want to first flash an WM5 ROM from one of the posts then try to flash WM6 as this is the prescribed method starting from WM2003.
I have a Cingular 8525 running WM5 that is stuck in bootloader screen. I have tried to soft and hard reset ... just boots back to the same screen, I can't turn it off once in the screen and when i sync via usb to the pc i get the message that the "usb device that is connected is malfunctioning" I have not done any upgrading at all and the phone worked perfectly right up till the time i powered it down and restarted into the bootloader screen.
Please can someone out there help me with this issue?
Zulu137 said:
I have a Cingular 8525 running WM5 that is stuck in bootloader screen. I have tried to soft and hard reset ... just boots back to the same screen, I can't turn it off once in the screen and when i sync via usb to the pc i get the message that the "usb device that is connected is malfunctioning" I have not done any upgrading at all and the phone worked perfectly right up till the time i powered it down and restarted into the bootloader screen.
Please can someone out there help me with this issue?
Click to expand...
Click to collapse
same problems, run perfect before with schaps wm6 rom then flash to faria wm6.1... not feel good with faria. try to flash with other rom then the problem start ..
how to recover ....... please help
Asfarizal said:
same problems, run perfect before with schaps wm6 rom then flash to faria wm6.1... not feel good with faria. try to flash with other rom then the problem start ..
how to recover ....... please help
Click to expand...
Click to collapse
Manage to solve the problem ...thanks WIKI !!
Go to Bootloader mode: Hold side OK and POWER buttons together and reset with stylus
Then Flash to any ROM you want !!
Thanks .... But
Thanks for the reply ... but i have no idea how to do what you tell me, I am new to all this phone "stuff" as a matter of fact this is the first time that i am ever using one of these forums. I have read till i am cross eyed but dont actually understand what you are talking about ... now don't let that scare you away as i am willing to learn and i am not braindead ... you all had to start sometime in this, not so. I get that i need to try and reflash my rom...
so is there some type of rom update software that i need? ... what is a hard SPL?? ... and who is Schaps?? .. sorry guys to do this to you but i would like to get into this game and i need some ( well maybe a lot ) of pointers.
Thanks for your time.
1. Search for "mr vanxs guide" so you have an idea on what you're doing.
2. OK, as Asfarizal said "Go to Bootloader mode: Hold side OK and POWER buttons together and reset with stylus". If you cant work out what the buttons are, go to the manual. it will tell you.
3. type in "hard SPL" in search on the forum & download the .zip or .rar file. this should have 2 files inside when opened,
a). RUUWrapper.exe and
b). RUU_signed.nbh
sync Hermes and double click .exe file. follow prompts.
4. find a rom that you want (would suggest TNT SE as a fairly good rom for noobs... good and stable, no problems...) Again download, then (and this is personel preference) format an sd card fat 32 and copy RUU_signed.nbh into root directory. Rename it Hermimg.nbh. Put into Phone and put into bootloader(make sure the battery is more than 50%) follow prompts. This should get you out of trouble. You can also sync your Phone and double click on the RUUWrapper.exe HOWEVER, if you should reset your computer, pull out the usb cable or have anything else happen to the computer that interrupts the flashm, you could end up with a worse brick than you have now. try to read up on flashing (search for "mr vanxs guide") and this should help you a lot if you have other questions. Good luck and happy flashing......
Thank You
I will follow the instructions you gave and try to get it going this weekend.
Thank you so much for your time
Zulu137 said:
Thanks for the reply ... but i have no idea how to do what you tell me, I am new to all this phone "stuff" as a matter of fact this is the first time that i am ever using one of these forums. I have read till i am cross eyed but dont actually understand what you are talking about ... now don't let that scare you away as i am willing to learn and i am not braindead ... you all had to start sometime in this, not so. I get that i need to try and reflash my rom...
so is there some type of rom update software that i need? ... what is a hard SPL?? ... and who is Schaps?? .. sorry guys to do this to you but i would like to get into this game and i need some ( well maybe a lot ) of pointers.
Thanks for your time.
Click to expand...
Click to collapse
Looks like you've got a lot of reading to do, and a problem to sort out. Firstly a couple of answers...
Schaps is a Rom Cooking guru (makes custom versions of WM5, WM6 etc). When you get your phone sorted out I'd recommend trying one of his roms.
Hard SPL. The SPL is part of the bootloader which effectively dictates how a rom is flashed and what roms can be flashed. HardSPL is a custom version of this which allows you to flash any rom from any carrier. It also protects against a bad flash in many cases. It is recommended before you try flashing any new roms or radio roms. Use Hard-SPL-V7 at the bottom of the first post here.
The Rom upgrading software is contained in any of the cooked or carrier supplied roms. It is normally a .zip file which cotains 2 files: xxxxxRUU.exe and RUU_signed.nbh. You run the .exe file from your PC when connected to your phone via USB. More details of how to do this are in MrVanx's guides. Also other resources here.
Now to try to sort your phone out...
What is displayed on your screen when in bootloader mode? It should be something like this:
HERM200
IPL-1.04
HERM200
SPL-2.10.Olipro (This is HardSPL V7)
If you don't have an Olipro SPL then you need to get HardSPL onto your phone. If you haven't done any upgrading and have had the phone from new then I guess you don't have hardSPL.
Now you need to fix your USB Malfunctioning problem. I can't help too much here except to suggest trying a different cable, different USB port or different PC. Also, if you are running Vista try an XP maxhine. When you connect to the PC does your phone show Serial or USB on the screen? If you can't get a USB connection, all is not lost - you can re-flash your rom using an SD card, method here.
There is a thread about un-bricking phones which may help.
There are various diagnostic tools (which can also screw your phone if used incorrectly). The favourite of these is MTTY but you need a USB connection to use this.
If your phone is in warranty I'd recommend getting your supplier to sort it out, but if not I'd try to re-flash an ORIGINAL supplier rom (Cingular I guess). You can get links to the official supplier roms here.
I think (might be wrong) that sometimes when stuck in bootloader you need to flash an official rom, not a cooked one to recover your phone - then you can run HardSPL and then flash cooked roms again.
Cingular 8525 stuck in bootloader
Thanks for the reply ... lots of great input.
Now to answer some of your questions.
1) When I power up the phone (only pushing the power button ) it goes straight into the bootloader screen without pushing any other buttons, and it displays
HERM100
IPL-1.01
HERM100
SPL-1.06
Then at the bottom in the white bar it says "Serial"
The only way that i have found to power it down again is to remove the battery, there is no response from any single buttons after it is in bootloader
the soft reset and hard reset work but it just goes right back to the bootloader screen after.
2) The USB malfunction. This only started after the phone "crashed" and before that it worked great ... well i only used it to sync up to my work pc for the contacts and to get pictures onto my hard drive.
all the PC's that i use are running XP. I have tried my home PC and my Laptop
and the work PC and all of them have their own cables and they all say the same thing ... "the USB device is malfunctioning"
I am sure that when i get the phone going again the USB will start to function again.
3) Phone warranty ... I bought the phone off e-bay from a store in new york about 10 months ago as a "new unlocked cingular 8525" it was new and unlocked, but i have no idea how they unlocked it. I would assume that there would be no warranty now and in any case i live in Canada and would have to ship it down to the states to an AT&T repair center and that sounds like a nightmare to me with the customs and so on.
I will give you a little more background on the problem. the phone worked like a charm without any problems at all for the 10 months that i had it, then the morning of the crash the phones alarm did not go off in the morning and i was almost late for work ... i did not pay it any further attention untill at 3:26pm
that afternoon the alarm went off ??????? (it was set for 6:05am) so i checked the main clock time, it was right. I then checked the alarm time, it was right ??? So i figured that something must have just got confused, so i powered down the phone with the power button to just restart it and while it was powered down i removed the battery to take the oportunity to to clean all those fuzzies and dust that collect in the battery compartment out and put it all together and powered it up again (just by pushing the power button) and this wierd red, green, blue and white screen appeared and that is all that i have seen since ???
I hope that answers your questions and i will start going through the links that you sent and get to reading ... will there be a pop quiz ... lol
Thanks again for your time and i very much appreciate all the time that all of you have spent on me and my phone ..... I know that you all just feel bad for me because i now have to use a Motorolla V551 ... lol
Great Work
ultramag69 said:
1. Search for "mr vanxs guide" so you have an idea on what you're doing.
2. OK, as Asfarizal said "Go to Bootloader mode: Hold side OK and POWER buttons together and reset with stylus". If you cant work out what the buttons are, go to the manual. it will tell you.
3. type in "hard SPL" in search on the forum & download the .zip or .rar file. this should have 2 files inside when opened,
a). RUUWrapper.exe and
b). RUU_signed.nbh
sync Hermes and double click .exe file. follow prompts.
4. find a rom that you want (would suggest TNT SE as a fairly good rom for noobs... good and stable, no problems...) Again download, then (and this is personel preference) format an sd card fat 32 and copy RUU_signed.nbh into root directory. Rename it Hermimg.nbh. Put into Phone and put into bootloader(make sure the battery is more than 50%) follow prompts. This should get you out of trouble. You can also sync your Phone and double click on the RUUWrapper.exe HOWEVER, if you should reset your computer, pull out the usb cable or have anything else happen to the computer that interrupts the flashm, you could end up with a worse brick than you have now. try to read up on flashing (search for "mr vanxs guide") and this should help you a lot if you have other questions. Good luck and happy flashing......
Click to expand...
Click to collapse
Thanks a lot man & great work i unbricked my Herm100 with method u mention above thanks a lot & great job keep it up
I also have this problem.
I d/l Hard-SPL-V7
and when i run RUUWrapper.exe
I get an error saying the application failed to initialize properly (0xc0000135)
What's going on?
How do i fix this?
this happened when i was trying to unlock the phone.
Thanks
need help
when i switch on my orange herm100 it shows On the bootloader screen is displayed:
HERM100
I PL-1.01
HERM100
SPL-1.40.01ipro
history : i buy unlocked orange phone
fewdays back i found no imei ,
yesterday i try to flash by micro sd but in gsm stage its gets hang no progress after extrom stage
IPL - OK
BOOTLOADER - OK
SPLASH1 - OK
SPLASH2 - OK
EXTROM - OK
GSM - (NO ACTION)
OS -
i tryed several time no action, i cant connect by mini usb.
PLEASE help me
tell me which it the right rom to chose? step by step procedure..
how to rectify imei?
thanks and regards
kirtibas
kirtibas, sorry it took so long to reply, 1st thing I'd do is upgrade to SPL 2.10 olipro. This is safer to use than others. then I'd suggest reflashing a stock rom to see if that works. After stock rom works then use a cooked rom as your heart desires... Cheers...
hi all,
my jasjar had an error while upgrading to ranju 7.7,
i tried to reset, didn't came back,
hard reset neither,
i went to bootloader mode, i could,
i connected it again to the pc, it showed usb,
i tried to flash to Rom that was working previously it arrives to 7% than stops,
what should i do ...
i tried to flash with official rom, it says that the rom wasn't designed for this model, it has worked before...
please help...
Hi,
if you search in the ranju's thread there's the solution.
You could have the doc corrupted. Simply read the wiki,
you must use mtty to format your device and then reflash the rom you want (with radio rom also).
Had similar problem
upgrading Imate JasJar to Ranju 7.7, only at first it showed as success, then it started behaving funny during customization, then failed to customize, then got stuck on Windows 6.1 green flash screen and eventually refused to budge beyond blue Imate screen with versions info. I tried everything, a few dozens of hard resets returned me to the same problem, removing the battery didn't do much and mtty didn't show USB as available option, so couldn't even use that. I was pretty much stuck solidly and for a while. At my wits end I read that problems like mine are associated with DOC corruption and my JasJar is as good as dead, quite a few people suggested to those who are in the same position to throw their bricked babies away, as there is no economic solution apart from sending it for service where the corrupted chip may be replaced. What do you know, I followed wiki recommendation and entered a boot screen by pressing light power reset, then just flashed back to Ranju 7.6 and my JasJar was brought back to life!!! The update went without a glitch and everything is working fine. I guess I will keep the 7.7 on my O2 and 7.6 on my Imate for now, won't be risking an update anymore on the JasJar, don't think I have much hair left after all the pulling I did trying to bring it back to life. Hope this helps someone in the same predicament
jokove said:
hi all,
my jasjar had an error while upgrading to ranju 7.7,
i tried to reset, didn't came back,
hard reset neither,
i went to bootloader mode, i could,
i connected it again to the pc, it showed usb,
i tried to flash to Rom that was working previously it arrives to 7% than stops,
what should i do ...
i tried to flash with official rom, it says that the rom wasn't designed for this model, it has worked before...
please help...
Click to expand...
Click to collapse
does it turn on at all?
Does the device turn on at all after a hard reset?
Dude, I had a same problem it rectified though, check following of my blog...
http://jay-joshi.spaces.live.com/blog/cns!851D717EDFF14CEC!3258.entry
or
http://buzzdev.net/read.php?40,13307,page=1
Rarest_Kind said:
Dude, I had a same problem it rectified though, check following of my blog...
http://jay-joshi.spaces.live.com/blog/cns!851D717EDFF14CEC!3258.entry
or
http://buzzdev.net/read.php?40,13307,page=1
Click to expand...
Click to collapse
Problem resolved?
Hello mates,
My i-mate Jasjar doesn't start any longer. Here's how I got here. I tried to flash my jasjar with Crossbow ROM using ROMUpgradeUt.exe but it didn't do anything. So I went into the Country_ID_Error folder on the computer and executed MaUpgradeUt_noID.exe. My jasjar froze after this and everytime I restarted it just hung on the bootscreen that says i-mate.
So I tried using mamaich method using mtty and now I can't even get to the i-mate bootscreen. So nothing just happens when I try to power up the phone (I'm sure the battery isn't dead).
All I can do is just enter the bootloader mode. That is the only thing that I can do that I know.
Please suggest something. I'm lifeless without the i-mate.
Thanks and regards,
Aditya More.
i had this same issue, i task28?'d my device, whatever command that resets the flash structure, then booted into bootloader, and flashed this file:
http://rs507.rapidshare.com/files/184081773/JASJAR_WWE_11353_137_10301.zip
that should fix you up real good, hopefully.
Well thanks a lot. But it doesn't help. It gives me a connection error when everything is fine. USB is connected, ActiveSync USB connection is disallowed.
I forgot to mention, that when I task 28'd my device, nothing showed on the device. It just showed USB at the top and v2.01 at the bottom for ever, which means the task 28 wasn't probably successful or I ain't sure what.
Yeah, I had to ask you how if the above given file will work if the phone is in bootloader mode.
To fill you on more details, my phone somehow strangely starts. I'll explain how.
When the phone is switched off, and when I press the reset button, nothing actually happens, no activities can be observed.
When the phone is switched off and I connect it to the computer via USB, it shows the charging light. Now when I press the reset button with the phone connected to the USB, the charging light goes off and the USB detection sound sounds on the computer and the computer shows "USB Device not recognized". This means the phone started.
But strangely in both the above cases, none of the two lights on the phone indicate anything and display of the phone shows absolutely nothing.
The only thing I can do with the phone now is enter bootloader.
Also, since I compromised so much, is it possible that I can still flash it with WM6? Because going back to WM5 will make me feel miserable.
Thanks.
@cheapusenet:
I tried flashing with that file. It flashed successfully, but the screen is all smudged. I soft reseted the phone too (using reset+two soft keys) but it keeps displaying that same smudged screen.
Good news is it did something.
Bad new is that it didn't make the mate work.
Please help. I'm dying without the phone.
Thanks and best regards,
Aditya More.
is it possible you can get a picture of what screen its showing? I THINK it happened on mine as well, did you let it sit for 10 or so minutes? if i recall the bootscreen was all corrupted but it started into WM5 just fine.
and regarding wm6, i'd attempt to get the device working before you try and get fancy. is the device cid unlocked? mine was and thats what was causing the issues.
Originally Posted by mamaich
if you can enter bootloader - use "task 28 55aa", this would restore DOC to its original layout.
If you cannot - contact service center.
if you didnt run that exact command, it's probably a good idea.
and you could try reflashing that stock imate rom?
This is all that happens.. I have waited for 5 minutes. I'll wait for 20 minutes now.
i waited for 30 minutes.. no go..
yap it did that EXACT same thing to mine.
reflash it, i think that fixed mine.
if that doesnt work, attempt flashing some custom roms.
is it CID unlocked?
i flashed it twice.. no go..
what's CID unlocked?
CID
Read the Wiki on my sig link
cid unlock allows flashing of roms that don't match your device branding.
i don't remember what brought me back from that, i may have flashed a custom rom with the imate cid settings in it? i don't remember.
i'll post a rom that i think may have helped in a few hours, I have slow upload speed. until then, just keep tinkering.
also, you should only be flashing nk.nbf. not the ms, or radio nbfs.
http://milfweed.info/UNI_AKU3_2_WWE_IVAN_beta_4_extrom_public.rar
try that rom.
hey man.. Flashed the rom with Ranju's ROM of WM6.1.. it worked.. But I can get the phone to be turned on. i mean device turns on but I can't make or receive calls or text. Let me check the thread of that rom. Thanks a ton for your support. Really appreciate it.