I have had my 8525 for less than two months, did the research the first time, used Hard-SPL, a black edition rom, etc. I was loving the phone with no issues at all, except maybe redoing a few things. When, BAM I get a brick for no apparent reason!
I pulled the phone out of its holster and tapped the O/I button as usually, nothing, then I watched the light and noticed it was not blinking. It has not responded to anything since, I have tried:
removing the battery and replacing
stylus inserted soft reset
attaching to the charger
It does not even show any LED indicators for charging. Of course running a cooked rom, my first thought was that. However, the symptoms seem to say that is paranoia. It seems to not even respond to a charger with an amber LED would have to be something hardware based.
I will mention that this was a refurb (for $149 which made it worth it) and it is still in the 90 day warranty.
I just want some feedback if anyone has it on anything to try with the phone before calling the warranty exchange.
Do you get at least a red led light when plugging in the phone to the charger without having the battery in? If yes I would say the battery said GODBYE ...
What did you do last on the device?
Have you tried a Hard Reset?
As mentioned above, no LED indicators for anything at all.
I did try a hard reset as well, nothing at all!
I assumed since this was a refurb maybe a previous mode of failure reoccured. I called warranty and requested a replacement. It arrived today. Now to start tweaking all over again. If this is a blatantly obvious hardware problem, I wonder if anyone in RMA will even know what software is one it, or will care? I hope there is no huge fine impending
I RMA it. No lights nothing its toast, probably hardware... If it is unresponsive to you they most likely won't be able to check the OS.
Hi rodent, where do you buy your hermes from? $149 seems to be a good deal
rodent said:
I have had my 8525 for less than two months, did the research the first time, used Hard-SPL, a black edition rom, etc. I was loving the phone with no issues at all, except maybe redoing a few things. When, BAM I get a brick for no apparent reason!
I pulled the phone out of its holster and tapped the O/I button as usually, nothing, then I watched the light and noticed it was not blinking. It has not responded to anything since, I have tried:
removing the battery and replacing
stylus inserted soft reset
attaching to the charger
It does not even show any LED indicators for charging. Of course running a cooked rom, my first thought was that. However, the symptoms seem to say that is paranoia. It seems to not even respond to a charger with an amber LED would have to be something hardware based.
I will mention that this was a refurb (for $149 which made it worth it) and it is still in the 90 day warranty.
I just want some feedback if anyone has it on anything to try with the phone before calling the warranty exchange.
Click to expand...
Click to collapse
I got it from AT&T(then Cingular) If you were signing or renewing a contract a refurbished 8525 was $149. I believe the same deal is now $199. But they may drop again, it was only two months ago.
Hey if you're going to college (like me ) then you can prob get a brand new one from AT&T Premier! Go here to get started: http://www.wireless.att.com/businesscenter/
Good luck! My new 8525 cost me $80.24! A tilt will set you back about 290 tho if you get the unlimited data package I think.
Hey guys, I bought an 8525 on ebay today with the following problems:
* Fail Test Call
* Bad LCD
The seller wrote "The phone Powers Up in that the light in the Upper Right Corner lights up but nothing appears on the LCD screen so I have no idea if the LCD is Good or Bad."
Do either of these issues seem like anything any of you have encountered/overcome? I'm more worried about the LCD think than the failed test call because I'm pretty sure flashing a new rom/radio will fix that issue assuming it is an issue at all. All help will be appreciated, thanks guys.
nobody? come on guys i have looked through these forums and haven't found any solutions... any ideas at all would be helpful. thanks..
chbearsrock said:
Hey guys, I bought an 8525 on ebay today with the following problems:
* Fail Test Call
* Bad LCD
The seller wrote "The phone Powers Up in that the light in the Upper Right Corner lights up but nothing appears on the LCD screen so I have no idea if the LCD is Good or Bad."
Do either of these issues seem like anything any of you have encountered/overcome? I'm more worried about the LCD think than the failed test call because I'm pretty sure flashing a new rom/radio will fix that issue assuming it is an issue at all. All help will be appreciated, thanks guys.
Click to expand...
Click to collapse
Did you try powering up by soft-resetting? My phone failed on me, only once (to date), where the normal power-cycle button didn't work. Using the stylus in the reset-hole turned it on, and I then hard-reset and restored from a backup, and everything was fine again.
To see how much of the device is working, why not hook up to ActiveSync and see if anything other than the LED is working? If so, using some remote control SW (if you can install on the device) might let you test some of the functionality. MS Remote Console Display only requires a single executable file on the device (which you could place there with AS), but I don't know how you'll get past the initial startup and setup clicks.
It sounds to me like you might have bought a device that could be more suited to parts farming, if you're not up to opening it up and doing some micro-surgery. I wouldn't gamble on the test call being fixable with a radio rom flash, but heck, it's worth a shot. But then again, I might just be being pessimistic.
Good luck in your endeavor,
-pvs
PS: You might want to have a look at this thread. Sounds like it might be a similar issue, although it has not led to a successful repair. :-(
thanks for the response! i hope that the reset button is the solution to my problems...wouldnt that be great? i'm not opposed to opening the phone up (i assumed i would have to) so if that doesn't work i will open it and make sure all of the ribbons are in correctly...not sure what else to do...thanks for all your advice though i'll be sure to follow your steps as soon as i get the device (hopefully by saturday).
i'll keep this post updated.
ok so i said i would keep this post updated (though i don't think anyone read it to begin with) so here's the update. I got the phone in the mail yesterday and it turns out that it does not turn on at all. When I plug it into the computer I get the red light (indicating no battery) but none of the fixes seem to work. I thought it would be a firmware thing but i'm now guessing that its a hardware issue, meaning i dont know where to begin. Unfortunately it looks as though its going right back on ebay...
tsk i upgraded the radio version after i fixed my phone to work invariably better from when i got it. i was so happy it was stable. i plug it in my usb and happily transferring files. i leave it and i come back decide to see what the fuss about the radio is so i decided to upgrade to the file HERM_Radinly_1.43.00 ... after successfully loading, not for long about 5 more mins plugged poof! disconnect sound. lcd faded. phone fried no red light when plugged. have two batteries so it's not the batteries. not the connections either. nothing. dead. tsk... and i was so excited.
chbearsrock said:
ok so i said i would keep this post updated (though i don't think anyone read it to begin with) so here's the update. I got the phone in the mail yesterday and it turns out that it does not turn on at all. When I plug it into the computer I get the red light (indicating no battery) but none of the fixes seem to work. I thought it would be a firmware thing but i'm now guessing that its a hardware issue, meaning i dont know where to begin. Unfortunately it looks as though its going right back on ebay...
Click to expand...
Click to collapse
@All,
As a celebration for my 1000th post, I decided to open a new thread based on Tweakman's idea, which seemed to work very well in the Development and Hacking Section. The idea is simple, a single thread for all Questions, Problems, and Concerns regarding Blue Angel. This includes, but it is not limited to:
[highlight]*Problems with Flashing.[/highlight]
Can't get your device in bootloader? Did it freeze during flashing and now it doesn't get past the 4 colored screen? Are you a complete noob and need some guidance as to how to flash? Etc.
[highlight]*Have questions about which Rom is best?[/highlight]
[highlight]*Want to install software but don't know if it is compatible with your BA[/highlight]
You get my point. All the questions that I have seen/answered over the past couple of months are just repetitions of posts, threads, and things that are readily available on the wiki or in other threads. However, people are either lazy, don't know what a Wiki is / where to find it, or just flat out don't know how to search (or read the forum rules for that matter). Having something general (in this case a sticky) that says "Hey, if you have a question, you can ask here" should draw enough attention and start minimizing the number of new threads and posts opened by users (both new and seasoned). This way, we will be able to keep the development threads a little cleaner and smaller... hence making the site's search function work a little better in the process.
@Seniors,
Kinda like the Q&A team, I will need your help in trying to keep the influx of questions to a certain level by answering them as we see them. None of us are logged in 24/7 (or at least some of us aren't ), but if you guys see a question, please try to answer it. I know that xplode, Chef_Tony, markanthonypr, red_hanks, sun_dream, imatrix, +Que_PPC, motisu, and others normally try to keep this under control, but if we centralize it and contain it, we will have a cleaner forum.
Reserved for future use.
Post Stickied Per Request...
Siemens SX66 BlueAngel Q&A, Help
You know very well you can count on us. Great idea mate. Also congrats on your 1,000's post. I've added a few "tags" to the thread. I hope some others do the same to. Tags help users to find what they are looking for when they use search.
hi
hi specialists
my friend has Blue Angel,he has strange problems.
in (sounds & notification),it didnot saved after changing any parameter,we tried by reflash the rom again,but nothing changed,also we reinstalled radio 1.15 but no change,also the ring tone of the msg is discontinue or irregular when played,and some times didnot wake up (of the device) when recieve a msg.
this is strange issued problems but in mine (BA) every thing is ok,this problems only in my friend (BA),I mate PDA2K.
any ideas?any suggestions?
thnx
notice:when we down grade to wm 6.1 every thing is ok
homam_france said:
hi specialists
my friend has Blue Angel,he has strange problems.
in (sounds & notification),it didnot saved after changing any parameter,we tried by reflash the rom again,but nothing changed,also we reinstalled radio 1.15 but no change,also the ring tone of the msg is discontinue or irregular when played,and some times didnot wake up (of the device) when recieve a msg.
this is strange issued problems but in mine (BA) every thing is ok,this problems only in my friend (BA),I mate PDA2K.
any ideas?any suggestions?
thnx
notice:when we down grade to wm 6.1 every thing is ok
Click to expand...
Click to collapse
Hey homam,
Thanks for kicking things off
First of all, which OS were you having problems with? This is important because it could have been a bug in a rom that could have been fixed in a later version.
@mark,
I know I can count on you, buddy I need help from the mods as well though. I cannot redirect posts to here and/or close threads
My BA, keeps turning on from standby, by a light shock! I maen, if you press the Power button, and then you knock gently on it's back, it turns back on!!
I've set to "Lock all buttons except the power button", However, I still have this issue.
Well, I must confess that once it dropped off of my hand, and it's the result of that...
Any ideas?
by "it turns back on" i assume you mean it wakes up from stand by, it doesn't really start like after a soft reset, right?
since the BA's only battery activated wake-up is in the cradle and we are not talking about soft reset, my first guess is, the battery is not to blame.
have you checked whether you can use your camera at all time? i mean, the camera_detect does not usually run at all times but if the camera connector is a little lose, from now and then it could "discover" the new camera hardware and wake up, that is unlikely for normal devices, but if yours had a crash before...
you could refer to this site for checking possible hardware reasons:
http://www.land-of-kain.de/ppc/mda3/disassembly/
the hardware things aside, there are also many possible software reasons for the device to wake up on:
- update of titanium weather
- automatic email checking
- cell broadcast
- if bluetooth is on
- if beam is on
- automatic update of any software...
plus of course the usual:
- incoming call
- incoming text message
- incoming mms
- upcoming calendar event...
so please check the possible software wake ups first to make sure this is really a hardware issue, because that would be a shame, that could be tricky to solve.
or let me put it this way, if it is really the moving that wakes it up, you have the first BA with accelerometer
EDIT: last but not least, it could only be a bug, maybe a hard reset or change of the rom could also be a way to go, since spontaneous waking up is a known bug for BAs
Chef_Tony
If there was only a way to hack the hardware and make this work at least on Edge. I can live with everything else, but its a shame paying for a full unlimited Internet service and only getting G connection Sighhhhhhh
Ok, I had to let that frustration out !!!!!!
Chef_Tony said:
by "it turns back on" i assume you mean it wakes up from stand by, it doesn't really start like after a soft reset, right?
since the BA's only battery activated wake-up is in the cradle and we are not talking about soft reset, my first guess is, the battery is not to blame.
have you checked whether you can use your camera at all time? i mean, the camera_detect does not usually run at all times but if the camera connector is a little lose, from now and then it could "discover" the new camera hardware and wake up, that is unlikely for normal devices, but if yours had a crash before...
you could refer to this site for checking possible hardware reasons:
http://www.land-of-kain.de/ppc/mda3/disassembly/
the hardware things aside, there are also many possible software reasons for the device to wake up on:
- update of titanium weather
- automatic email checking
- cell broadcast
- if bluetooth is on
- if beam is on
- automatic update of any software...
plus of course the usual:
- incoming call
- incoming text message
- incoming mms
- upcoming calendar event...
so please check the possible software wake ups first to make sure this is really a hardware issue, because that would be a shame, that could be tricky to solve.
or let me put it this way, if it is really the moving that wakes it up, you have the first BA with accelerometer
EDIT: last but not least, it could only be a bug, maybe a hard reset or change of the rom could also be a way to go, since spontaneous waking up is a known bug for BAs
Chef_Tony
Click to expand...
Click to collapse
Wow! Tony! I really appreciate your complete answer. I mean it.
Yes, as you correctly assumed, I meant wake-up. It just wakes up and continues the routine WinMo operation; no soft-reset occurs.
It's less than a year that I've replaced the battery with a new one. I remember all the funny things used to happen when the old battery was dying. But non of them were similar to this one.
It can't be the Camera. Well, I'm able to use it all the time, and the "camera_detect" has been always loaded in the processes whenever I've checked it. About the looseness thing, ummm, I'm not sure. I tried to knock on it to see if it's more sensitive than other parts. I think the upper part of the device is more likely to wake it up by an easy hit (like knocking). but it's the whole upper part, not only the camera section nor the camera button.
Unfortunately, the software possibility, is unlikely to be the problem:
I've used many ROMs on my lovely BA which 3-4 times of them taken place since the wake-up problem.
The software and the usual reasons you counted, do wake it up. but shakes, too.
Finally, to be honest, I'm agree with you! This is the first Blue Angel with accelerometer. yeaaah! I did it!
I bet my friends that I can wake my BA up, without touching any buttons or screen! It's fun this way, but I comes to be annoying when I put it in my pocket or just put it on a table! and it wakes up... consider the forced battery consumption, unwanted screen taps if I don't lock the screen. God bless A_C! and... .
I know it's a hardware issue (((((
@raizaM: My Thought.... Have you ever taken it apart? One of my BA's had 3 loose bolts inside. All 3 were from what I think is the Radio/Antenna part at top. However, in my case, I had a rattle going inside. Thats why I put it apart. You might have something loose inside, causing a connection to arc when you knock on your phone. If you do deside to open it, there is a tutorial on the wiki on how to.
markanthonypr said:
@raizaM: My Thought.... Have you ever taken it apart? One of my BA's had 3 loose bolts inside. All 3 were from what I think is the Radio/Antenna part at top. However, in my case, I had a rattle going inside. Thats why I put it apart. You might have something loose inside, causing a connection to arc when you knock on your phone. If you do deside to open it, there is a tutorial on the wiki on how to.
Click to expand...
Click to collapse
Hey mark!
I had that same issue a while back, but with only one screw (also from the same area as yours).
@raizaM
Just to knock off Chef_Tony's theory out of the table completely, try to erase camera_detect.lnk from \Windows\startup and SR your device. If Chef was right, then your issue might be gone. However, I would follow markanthony's advice and take it apart in case Chef's idea doesn't work.
Oh man, your not my hero anymore LoL.. and here I thought I would be the only one with a mechanic inside my phone.
markanthonypr said:
Oh man, your not my hero anymore LoL.. and here I thought I would be the only one with a mechanic inside my phone.
Click to expand...
Click to collapse
Well, it kept me entertained when my BA would run out of juice
Thanks for your kind advices.
Actually, I tried to remove "camrea_detect" from the startup once, but any way, I gave it a shot again... no success...
Frankly, I'm a lil bit afraid to take my lovely BA apart... :-s... What if... :-(
But, I guess sooner or later I need to do so. so what the heck... lets do it.
Maybe I'll do it tonight. Guys please help me through it. I don't wanna loose my Angel!
Ton'y link provided in the previous posts, would be my start:
http://www.land-of-kain.de/ppc/mda3/disassembly/
any more advices?
raizaM: You're not going to go that far deep. Only remove the cover. If you look at picture #4 on that link, the top green area has about 6 bolts all around it. Those were the ones that were loose on mine. 2 of them were rattling inside the phone. I still can't believe they didn't cause a short circuit. You don't need to go down into the camshell area. Do you use the sliding keyboard? If so, you could have a bad flex cable. But, don't worry about tha for now. Just remove back cover and carefull inspect for loose bolts. Don't over tighten them.
all the master please help, my BA strange,,,,, the screen suddenly go dead after actived wifi or playing game, its suddenly dead, and i must push power button to turn it on again through proses like softreset, that in battery power. but if i conect in charger power mode, i turn wifi,playing game, its normal, the BA still on and working normal,
please2,,,,,if someone knows the problem please help, im desper now....
loryshoe said:
all the master please help, my BA strange,,,,, the screen suddenly go dead after actived wifi or playing game, its suddenly dead, and i must push power button to turn it on again through proses like softreset, that in battery power. but if i conect in charger power mode, i turn wifi,playing game, its normal, the BA still on and working normal,
please2,,,,,if someone knows the problem please help, im desper now....
Click to expand...
Click to collapse
It seems that you have the backlight settings set to dim/turn off too fast. Go to \Settings\System\Backlight and modify the settings in there (particularly the ones labeled "On Battery Power"). Then, soft reset the device (stylus on the bottom).
Hope this helps.
markanthonypr said:
raizaM: You're not going to go that far deep. Only remove the cover. If you look at picture #4 on that link, the top green area has about 6 bolts all around it. Those were the ones that were loose on mine. 2 of them were rattling inside the phone. I still can't believe they didn't cause a short circuit. You don't need to go down into the camshell area. Do you use the sliding keyboard? If so, you could have a bad flex cable. But, don't worry about tha for now. Just remove back cover and carefull inspect for loose bolts. Don't over tighten them.
Click to expand...
Click to collapse
egzthunder1 said:
It seems that you have the backlight settings set to dim/turn off too fast. Go to \Settings\System\Backlight and modify the settings in there (particularly the ones labeled "On Battery Power"). Then, soft reset the device (stylus on the bottom).
Hope this helps.
Click to expand...
Click to collapse
not the setting, it got black scren, its dead screen after running wifi or application, suddenly goes dead, black screen,.
Have you tried with another battery? It sounds to me like your battery is about to die. It won't hold the heavy battery consumption of Wi-Fi and heavy CPU usage while on Games. Try with another battery. Also make sure you followed Egzthunders suggestion to change your Power Settings. If you still need help, post back and include more info about your device, such as, what version of Windows are you running and how old/new is your battery.
Hi friends,
Please give me advices on this situation.
I bought a HD since 05/2009. I installed many cooked ROMs and it still fine until now.
When i've turned off the screen with power button and then turned it on, the screen still black, but i still can touch on it and it vibrate each time i touch. I tried to soft reset by push reset button at the back, pull out the battery .... The screen is always black, but the phone can start up and vibrates when i touch on the screen.
I thought the screen consist of 2 parts, one for displaying and one for touching. And the displaying part is died.
Then i connected it to PC in order to re-install with the ship ROM, and so strange, the screen work again right after i plugged the cable. But i still re-installed it with the ship ROM. But the error came back many times in few days later. And sometimes the method "connect to PC with cable" didn't work.
When feeling hopeless, i left the phone alone in some days and the screen suddenly works.
And now it has just turned back again and i dont know if it will be back or i must have it repair. (There is no warranty service for HTC in my country.)
Thanks for reading, i know that my English is terrible.
Check the backlight adjustment. As ridiculous as it may sound, with a rom I had it sometimes went to zero light on its own. Plug it and make sure that all settings are to maximum light, with the automatic function disabled, and see if it happens again.
Rizlo said:
Check the backlight adjustment. As ridiculous as it may sound, with a rom I had it sometimes went to zero light on its own. Plug it and make sure that all settings are to maximum light, with the automatic function disabled, and see if it happens again.
Click to expand...
Click to collapse
Thanks for your advice. I will do as you said and do pray
snowinjune said:
Thanks for your advice. I will do as you said and do pray
Click to expand...
Click to collapse
It's not work, ;(
snowinjune said:
It's not work, ;(
Click to expand...
Click to collapse
This happened to me once and I removed battery and left phone overnight. In the morning I insertedbattery again and problem hasn't materialised since.
However, if your issue keeps returning it looks like you would need to get phone fixed under warranty as it sounds like a loose connection between motherboard & LCD screen
Fallen Spartan said:
This happened to me once and I removed battery and left phone overnight. In the morning I insertedbattery again and problem hasn't materialised since.
However, if your issue keeps returning it looks like you would need to get phone fixed under warranty as it sounds like a loose connection between motherboard & LCD screen
Click to expand...
Click to collapse
I'll try with your advice . Thanks
Yeah but the fact that sometimes plugging the device to USB brings it back sounds like software to me. Anyway, I hope you find a way to fix it!
Fallen Spartan said:
This happened to me once and I removed battery and left phone overnight. In the morning I insertedbattery again and problem hasn't materialised since.
However, if your issue keeps returning it looks like you would need to get phone fixed under warranty as it sounds like a loose connection between motherboard & LCD screen
Click to expand...
Click to collapse
So sad, the issue occurs again when i need to make an important call. It drives me crazy because i were on the street and i must went to a post office. Then i realized that i do not remember the phone number.
I must get it fixed at weekend then i may sell it away. I'm dreaming of HTC Leo but maybe i will come back to my old iPhone 2G until Leo's price drops.
Thanks all for your help and listening.
Sorry to hear of your problems
If it was me, I would send the phone away on warranty and just use your iphone in the mean time.
snowinjune said:
So sad, the issue occurs again when i need to make an important call. It drives me crazy because i were on the street and i must went to a post office. Then i realized that i do not remember the phone number.
I must get it fixed at weekend then i may sell it away. I'm dreaming of HTC Leo but maybe i will come back to my old iPhone 2G until Leo's price drops.
Thanks all for your help and listening.
Click to expand...
Click to collapse
I'm sorry, but I think you have the same problem I had, the only solution was to send it to Tech center.
Take a look at this post (in french cause, i'm french ^^) http://htc-touch-hd.forumactif.biz/problemes-hardware-f6/sav-ici-on-parle-du-sav-t4061.htm
It describe all the symptoms I had, with some pics.
Hope you will fix it
X3n0n said:
I'm sorry, but I think you have the same problem I had, the only solution was to send it to Tech center.
Take a look at this post (in french cause, i'm french ^^) http://htc-touch-hd.forumactif.biz/problemes-hardware-f6/sav-ici-on-parle-du-sav-t4061.htm
It describe all the symptoms I had, with some pics.
Hope you will fix it
Click to expand...
Click to collapse
Thanks for your helpful info. I used google translate to read the post i found these info:
HTML:
Failure diagnosed by the technician:
- Pas d'allumage - No ignition
- Connecteur kit pieton deffectueux - Headset connector scientifically sound
- Defaut esthetique. - Cosmetic defects.
Pieces remplacées : Parts replaced:
- Carte mere - Motherboard
- Etiquette de violation - Etiquette violation
- Etiquette font de poste - Labels are post
- Nappe Systeme. - Tablecloth System.
I live in Vietnam, as i known there is no HTC warranty service in Vietnam. I bought this phone on a trip to USA. Base on your experience, i think i may pay a lots to fix it in VN. I will bring it to a repair shop at weekend and ask for the cost.
Ha ha, bad luck for me.
Hello all.
I have a HD2 that I havent done anything with, exept getting and installing some small programs.
No new ROM, no attempt to install W7, its more or like a Virgin.
However I made a fool of me, and managed to damage the LCD and finally got it changed. Got the Phone back from the company (MBlue Ltd in UK), and tried to start it up. But No....
Pressing ON, the phone vibrates, gives some light in the screen, sort of like you see its ON its a "white glow", but you dont get any more. The Jingle comes on, theres light in my buttons at the low end of phone, and NOTHING more.
I have had it on for long time, but nothing....
When I finally sendt the phone away, the battery was discharged, but as I have a new battery I put that in, and it charges and all.
Ive studied this thread: forum.xda-developers.com/showthread.php?t=638210
But as I CAN charge I fell that Im somewhat related but not fully in the same situation as the Original Poster there.
# Could it be that my phone somewhat has gotten overheated or anything else?
# Is the only and best solution to send it to HTC and let them look on it?
Ive tried to HARD and SOFT reset, but still nothing.
[EDIT] Connecting the phone to my PC, It is recognised and its recognised as a HD2 T8585
Looking more and reading more on the Forum I suspect theres a problem in the connection between the "fx-card" and the screen. (stupid way of saying it though)
Glad for any input here. Thanks in advance.
Tom
Flattop said:
Hello all.
I have a HD2 that I havent done anything with, exept getting and installing some small programs.
No new ROM, no attempt to install W7, its more or like a Virgin.
However I made a fool of me, and managed to damage the LCD and finally got it changed. Got the Phone back from the company (MBlue Ltd in UK), and tried to start it up. But No....
Pressing ON, the phone vibrates, gives some light in the screen, sort of like you see its ON its a "white glow", but you dont get any more. The Jingle comes on, theres light in my buttons at the low end of phone, and NOTHING more.
I have had it on for long time, but nothing....
When I finally sendt the phone away, the battery was discharged, but as I have a new battery I put that in, and it charges and all.
Ive studied this thread: forum.xda-developers.com/showthread.php?t=638210
But as I CAN charge I fell that Im somewhat related but not fully in the same situation as the Original Poster there.
# Could it be that my phone somewhat has gotten overheated or anything else?
# Is the only and best solution to send it to HTC and let them look on it?
Ive tried to HARD and SOFT reset, but still nothing.
[EDIT] Connecting the phone to my PC, It is recognised and its recognised as a HD2 T8585
Looking more and reading more on the Forum I suspect theres a problem in the connection between the "fx-card" and the screen. (stupid way of saying it though)
Glad for any input here. Thanks in advance.
Tom
Click to expand...
Click to collapse
Does your computer synchronize with your phone(connecting to activesync/mobile device center)? Then it is booted in Windows Mobile, the possibility is that the screen is broken then.
I thought the Screen might not be properly connected, or broken yes.
I better get in contact with the repair company.
But if other too have opininons, please bring em on... ;-)
Returned to repairplace, they fixed it.
My best guess is thy didnt check their own repair so they had to connect/fix something.
Flattop said:
Returned to repairplace, they fixed it.
My best guess is thy didnt check their own repair so they had to connect/fix something.
Click to expand...
Click to collapse
Good point, they're responsible for their repair: it is better this way because it's possible they damaged something while repairing and that part, if needs replacement, it should be their obligation, not yours!