LCD align problem solution any1? - 8125, K-JAM, P4300, MDA Vario General

hi there
well i have a cingular 8125 with lcd disalignment problem...
so, i crawled this forum and searched for a possible solution but i didnt find it..
so im asking the ones who hve the exact problem as me, how they solved the problem if: the thumb pressure, putting things beneath lcd, releasing screws, flashing to older ROMs and getting another Wizard etc etc etc-didnt work?

i had this problem too at my k-jam.
i flash new rom and now it's ok....

yes, i highly recommend u to change other roms, coz i had this problem before, then i flash another rom, and it works, at least up to now

Related

Everyone please help me....

i have a Swisscom XPA v1605 (htc tytn), and i had wm6. On wm6 I have problem with touchscreen on start button, a I hardreset the phone. After that my touchscreen does't work, and I can't calibrate screen and continue with starting up guide....What sould I do??? Someone answer PLEASE....
Reply
check that the front bezel is not dented and suppressing the touch panel around the sides, if not,,, you will need to replace the entire lcd...
also check if there are any objects( sand, pocket lint) stuck between the touoch panel and bezel.
I think, is there any posibility that the rom is false, becouse that phone should have wm5. Lcd is workin fine , but I can click on calibration. was I mentoned that the phone was wokin fine before that happen.(HARDRESET)
Try reflashing the ROM, I had a similar issue where it just stopped working and re flashing was the only cure.
how I do that? sry guys ,but I am brand NEW in this thing.....
Did the device come from Swisscom with WM6? If so your probably best contacting there support about it, they may be able to give you the download location of the rom. If not try reading MR Vanx's upgrading guides on here which will walk you through flashing the device. http://forum.xda-developers.com/showthread.php?t=299462
thx man u r awesome............
No problem as long as you follow it through you should be ok.
Good luck

alignment of the screen - ebay advice - help

Hi,
I have a friend with a wizard that also have the problematic alignment of the screen lost.
I am considering to order this kind of replace from ebay:
http://cgi.ebay.es/LCD-Touch-Screen...ryZ41343QQssPageNameZWDVWQQrdZ1QQcmdZViewItem
is this the correct hardware device?
thanks for the help
Rui
I guess its right, i never tried or bought it from eBay but by the pic and description it looks all right but dont go on my advice wait for other to post too.
I would suggest that you dismantle your wizard first and check the ribbon cable on your phone matches yours
I have replaced the digitizer on my old wizard before and found that there was 2 different digitizers, each had a slightly different ribbon cable. The first didnt work at all but the second worked perfectly. Also i noticed that on both digitizers the strips on the cables didnt align properly with the board, however it was still possible to solder.
Make sure you have a soldering iron with a very fine point, its very figity to replace.
veda_sticks said:
I would suggest that you dismantle your wizard first and check the ribbon cable on your phone matches yours
Click to expand...
Click to collapse
Thanks.
yes I will do it first. My problem was to understand if this is the hardware component that makes the lost of align issue.
Nowadays we have to open the keyboard to recover the align values.
Thanks to all
Thats a very weird problem, it may be software related, a bug in the OS maybe?
If that is the case then backing up your phone then flashing with a rom of your choice may fix the problem (i would try that first before replacing hardware)
Personaly i would suggest the brightphone rom its clean and very fast, however you have to identify wether your phone is a g3 or a g4 and get the right rom. all in the upgrading guides
veda_sticks said:
Thats a very weird problem, it may be software related, a bug in the OS maybe?
If that is the case then backing up your phone then flashing with a rom of your choice may fix the problem (i would try that first before replacing hardware)
Personaly i would suggest the brightphone rom its clean and very fast, however you have to identify wether your phone is a g3 or a g4 and get the right rom. all in the upgrading guides
Click to expand...
Click to collapse
Make a search and you will find lots of posts with this problem.
It was present sincd the wm5, wm6, wm6.1, etc.
So, it's really hardware.... unhappily
Rui

White screen SPV 3100

Hello all,
I'm newby at the forum and sorry for my bad English. I just read all the threads concerning my problem, before post this, and a can't find any solution
I bought this phone on ebay faulty. The seller tell that it only problem was white screen. I thought was simple to fix with flashing but... I tried to fix it using all the solutions even i just open it and clean with a soft brush but no luck
When i turn it on i just see a white screen. When a plug it in ac adapter he charge and when a plug it at my desktop e charge too but don't syncronize with active sync 4,5. For this i don't know if is a software or hardware issue.
I can't put into bootloader too.
Any Help? I don't want spend my money in a new lcd without your opinion.
Thanks in advance for all e regards from Portugal.
This topic has been covered many times, which is perhaps why folk will not answer in a new thread about it.
Have a look here:
http://forum.xda-developers.com/showthread.php?t=321163
But in summary:
Flashing will not cure it.
A new screen will probably not cure it.
In many cases it is caused by a fault on the d/pad. Replacing that might be successful. In the thread above look for the bit about putting padding on a d/pad chip - that seems to have worked for many (but not all)
Mike
Hi there. I just open a new thread cause i had read all the things in the link you gave, with no luck for me. But thank you for the help.
Hello! I have the same problem with my Hermes. But I know how to solve it - at least in my case. I had to open PDA and look inside. There's a tape (strip?) which is connected by two screws. Well, one is gone. The tape doesn't lie as it should so I had to connect it by glue. Now it's fine. It was physical damage, flashing wouldn't help much, especially here but my thougts were similiar in the beginning.
Good luck and Cheers

Help! Issues with my Qtek 9100/i-mate k-jam

Hi everybody,
I recently received a Qtek 9100 from a friend, but I'm having some issues with it.
Firstly, it has Windows Mobile 6.5 installed and I'd like to revert to the OEM version, 5.0, hoping for it to be less buggy, but I could not find a decent method. Could anyone advise, please?
Secondly, I'm having some issues with the display. At first I suspected a hardware issue, now I'm not that sure about it.
So,... after freezing (as WM6.5 seems to have this function really well implemented), I reset the device and instead of the boot screen I got a flickering light screen with all sorts of horizontal and vertical lines. I checked with eBay, found a new screen at a decent price and just as I was about to order the new screen, the display started working again, until last night when a soft reset sent it back where we started from, meaning all sorts of lines.
Now I'm thinking it's either a hardware issue such as a bad contact, or the lines are caused by the damn WM6.5. I'm leaning towards the hardware problem, since the boot loader doesn't show properly either.
Any advices would be greatly appreciated. Thanks in advance
It can be Omap overclocking. Try to look at the wiki for a original rom for your phone
it's hard to say what rom it had since i got it with wm6.5.
i found a link on this forum to a file called RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship_cingular.rar
it seems to be one of the many originals, so i'll try to flash this one as soon as i can figure out the connection issue with ActiveSync. I tried both 4.0 and 4.5 but they both fail to connect i need to fix the pda's display (or wait until it solves itself, like the previous time) in order to troubleshoot the connection error
Can you get into bootloader?
no, i keep getting those flickering horizontal and vertical lines. the odd piece is that anything else besides the connection seems to work. my guess is that the active sync connection can be solved via connection manager, but since i cannot see a damn thing... it's gonna be complicated.
my best guess is to buy a new display from ebay since i found some real cheap ones ($9) and replace it, hoping this would solve the hardware issue.
is there anybody else who got those mad lines? perhaps there's a less complicated solution to this problem that you would like to share
apparently, this is not a common issue, good to know
nobody had horizontal and vertical flickering lines?

Help, Jasjam got whitescreen :(

My jasjam has fallen from my hand on the concrete surface, after that, it got whitescreen problem. I ordered 3000mah + accessories for the jasjam but i wont use them. So plz help me. I tried pressing above the d-pad and opened the jasjam and reseated the cable on mainboard but problem still persists. I have read articles here and tried some but none worked.
PLZ HELP ME, I AM TRULY HELPLESS.
I opened the jasjam and fixed the problem and now it's working.
OK, so what was it?
hayabusa_ryu said:
I opened the jasjam and fixed the problem and now it's working.
Click to expand...
Click to collapse
For some reason people dont like answering hardware questions on these forums. People dont respond and then searches reveal nothing when new members ask these questions again.
So what did you do/find? Was it some connector which had come off in the fall which just needed pushing back on again?
Yes it was d-pad connector again.
Thats because sometimes people get lazy ..
I have been through that phase too...
searching "WHITE SCREEN" got me allot of results...
http://forum.xda-developers.com/showthread.php?t=321163&highlight=white+screen
Actually, I searched the whole forum and on net for white screen problem. And i also followed them with no positive result so I initiated a thread here. But later I keep trying/opening/reassembling the device and my device came to life but still any hardware buttons on my jasjam isn't working.
White screen issue usually involved with bad flex cable.
I Had this problem, and it was fixed by cleaning (gently) the contacts of the flex cable with toothbrush and contacts cleaner.
if that doesn't work for you, and you know that this is a flex cable issue, try to replace by a new one...
I have found this one, maybe you can find cheaper.
http://cgi.ebay.com/New-Flex-Cable-...ewItem&pt=PDA_Accessories&hash=item439b5d73d2http://cgi.ebay.com/New-Flex-Cable-...ewItem&pt=PDA_Accessories&hash=item4150b89467

Categories

Resources