Database Users

How To: Revert to Windows Mobile 2003

Whats needed:
TyphoonNBFTools: http://w1.whatcounter.com/dlcount.p...yphoonNBFTools_0.3_SPL1010064_SPVServices.zip
Any Official Rom (I used I-Mate SP3 WWE).
A Typhoon running Windows Mobile 5.0.
Reverting Back:
Run TyphoonNBFTools and Open the SPL1010064.nbf. Right click on SPL in the bottom part of the screen and choose Emergency Flash. If this is the first time you have used the program you will get a prompt on your phone to run the runtimes. Choose yes. Click OK to flash the new bootloader to your phone. Next disable Activesync by turning off USB connections. Turn off your phone. While holding down the Camera button insert the USB cable, the phone should run the bootloader and you will be presented with the tri-color screen. It should say USB in the bottom corner. Now run Mtty and choose USB connection. Hit enter in the blank white space. You should now see Cmd>. Type "info 2" without the quotes. You should see some information about your phone. Next type "format BINFS" agains without the quotes. This one is case sensitive. You should see format complete or something along those lines. Now close Mtty and re-enable USB connections. Run the exe from the update you downloaded and follow the instructions. Your phone should now boot back up to WM2003.
For those stuck in bootloader mode you will need to run mtty and reflash the wm5.bin to the phone then follow the steps above.

Leiden said:
Whats needed:
TyphoonNBFTools: http://w1.whatcounter.com/dlcount.p...yphoonNBFTools_0.3_SPL1010064_SPVServices.zip
Any Official Rom (I used I-Mate SP3 WWE).
A Typhoon running Windows Mobile 5.0.
Reverting Back:
Run TyphoonNBFTools and Open the SPL1010064.nbf. Right click on SPL in the bottom part of the screen and choose Emergency Flash. If this is the first time you have used the program you will get a prompt on your phone to run the runtimes. Choose yes. Click OK to flash the new bootloader to your phone. Next disable Activesync by turning off USB connections. Turn off your phone. While holding down the Camera button insert the USB cable, the phone should run the bootloader and you will be presented with the tri-color screen. It should say USB in the bottom corner. Now run Mtty and choose USB connection. Hit enter in the blank white space. You should now see Cmd>. Type "info 2" without the quotes. You should see some information about your phone. Next type "format BINFS" agains without the quotes. This one is case sensitive. You should see format complete or something along those lines. Now close Mtty and re-enable USB connections. Run the exe from the update you downloaded and follow the instructions. Your phone should now boot back up to WM2003.
For those stuck in bootloader mode you will need to run mtty and reflash the wm5.bin to the phone then follow the steps above.
Click to expand...
Click to collapse
Man! Can't thank you enough for this. I took my phone to the service centre, willing to pay for the repair, and they could not do it. Every thing works fine now. Very good manual, clear instructions and correct info!
THANKS!

Hi
I Am Trying To Follow The Procedure Mentioned. But When I Right Click On Spl I Am Not Getting 'emergency Flash' Active.
Can U Please Assist Me Regarding This

You need TyphoonNBFTools.dll installed on your phone. Try running TyphoonNBFTools and selecting Tools->Immediate Flash Tools->Test Immediate Flash. It should automatically install the required stuff for you. Check you phone when you run the program. You should get a prompt to installed a program from unknown publisher. Make sure to choose yes.

Stuck in bootloader
Just trying to do this following my question here.
I though it was going well but I have a major problem now! I managed to do the emergency flash, but every time I boot I just get the tricolour bootloader screen (IPL 1.00, SPL 1.01.0064) and can't get any further. Any ideas please? I have tried using mtty to load wm5.bin but get the error "MTTYDownloadImageNot allow operation!"
I have also tried re-doing the "format BINFS" and doing the above again but still no joy.
Any ideas would be much appreciated!

maybe u need to make a "goldcard"
my feeler (o2 xphoneII) lives again after flash with goldcard.

I can't find a way to create one for Typhoon, can you point me in the right direction?

I try flash Amadeus = Qtek 8100 with UpdateTool from Qtek 8310.
Update process stopped at 74% , and UpdateProgramm closed.
Now my Qtek 8100 not Powered ON , and can't enter in boot mode (tricolor screen) with "Camera" button hold + USB cable conneting.
PC don't see any USB devices when I connected my Qtek 8100 to USB port.
I think I erased Boot loader in my Qtek 8100 (but not sure).
Is any method for repair ?
WBR !

er1cc said:
I try flash Amadeus = Qtek 8100 with UpdateTool from Qtek 8310.
Update process stopped at 74% , and UpdateProgramm closed.
Now my Qtek 8100 not Powered ON , and can't enter in boot mode (tricolor screen) with "Camera" button hold + USB cable conneting.
PC don't see any USB devices when I connected my Qtek 8100 to USB port.
I think I erased Boot loader in my Qtek 8100 (but not sure).
Is any method for repair ?
WBR !
Click to expand...
Click to collapse
UR Phone is fried!
this happens to almost 1 out of 20 users.....that while downgrading/upgrading to another bootloader, ur phone becomes dead....

DomConway said:
Just trying to do this following my question here.
I though it was going well but I have a major problem now! I managed to do the emergency flash, but every time I boot I just get the tricolour bootloader screen (IPL 1.00, SPL 1.01.0064) and can't get any further. Any ideas please? I have tried using mtty to load wm5.bin but get the error "MTTYDownloadImageNot allow operation!"
I have also tried re-doing the "format BINFS" and doing the above again but still no joy.
Any ideas would be much appreciated!
Click to expand...
Click to collapse
get the tricolour bootloader type in mtty info 2 the type format BINFS then upgrade using rom upgrade

DomConway said:
Just trying to do this following my question here.
I though it was going well but I have a major problem now! I managed to do the emergency flash, but every time I boot I just get the tricolour bootloader screen (IPL 1.00, SPL 1.01.0064) and can't get any further. Any ideas please? I have tried using mtty to load wm5.bin but get the error "MTTYDownloadImageNot allow operation!"
I have also tried re-doing the "format BINFS" and doing the above again but still no joy.
Any ideas would be much appreciated!
Click to expand...
Click to collapse
i also got that problem but i reinstalled the patched RUU again and my phone now boot but i have not been able to go back to the 2003 as i insalled WM5 but still cant format the BINFS

If already have patcher the bootloader with the guide to upgrade to wm 6.0 can I ignore to do it again? I mean flash bootloader again ?

Issue of Using Athena Unlocker

First of All, I am Noob for all this flash phone stuff~~
I was using A-Unlocker last night on my Athena, however the phone got f**ked up
I was able to finish the Step 1 "Flash SPL". After I done with Step 1, here is I got from bootloader 3 Color Screen
ATHE 100
IPL-V1.00
ATHE100
SPL-V1.20. Olipro
and it unlocked Step 2 "Unlock Radio"
after the Step 2 there was a Notice popped up "Your Device must now be unlocked with a program, please configure your device and then connect and sync with Activesync. after doing so, click OK and watch your device screen"
and My phone stop at HTC loading screen, not able to boot to "Window Mobile" system. I did reset phone many times but didn't work.
Please Help Me Out here~~ Tyvm
p.s: I can still boot the phone to bootloader 3 Color Screen

please help me

Your device is okay. You can already proceed to flashing any ROM that is desgined for SPL 1.2. If you want just a good looking ROM, you might want to try PK3.0 ROM. If you want WM6.1, try irus ROM.
If I'm you, I'll skip any rom that uses SPL3.5 for the time being until you're sure there is a mean to come back to SPL 1.2. This mean you should skip AP4.0 for the time being.
To flash one of the SPL1.2 based ROM, remove your storage cards and SIM cards, and ensure your battery is close to full. Then get into Bootloader mode (by pressing down the Camera and poke into the reset hole - hold it down for a good few seconds until you see the tr-colored screen). Then connect your cable until you see USB on the device screen. Then on your PC, start the RomUpdateUtility program and follow the instruction on the PC.
Good luck.

Thx, man! U Rock!!
Just flash the phone with PK3.0 Rom~

i reeallyyyy need somebody's help with unbricking my phone.. please hellpppp!!

alright.. i made a similar post to this before and i came across the wiki...
well i can't view what my SPL or my IPL because as soon as i turn the device on, all that shows is the boot loader screen and displays serial on the top with 0.16-0.90 in red characters on the bottom (I'm not sure what those are)...
here are the only details that i know about my phone:
I DON'T have hard SPL
My Original ROM i was using before was an htc windows mobile 5 rom
The reason that my phone is bricked right now is because the usb cable disconnected in the middle of the flash
I'm using Windows Vista for flashing
Computer won't recognize the phone when on usb
My phone (qtek 9600) can't load the operating system
*EDIT*
THE PHONE IS STUCK ON BOOTLOADER WHEN I TURN IT ON, NOTHING ELSE, BUT THE BOOTLOADER SCRREN DOESN'T SHOW MY SPL AT ALL.
ALSO, MY COMPUTER DOESN'T RECOGNIZE THE PHONE....... MY PHONE HAS A TYPE 2A BRICK
Helping me will be greatly appreciated
come on.. I'm without a phone

Do you have a 2GB or smaller SD card? Copy a rom image to it and rename it HERMIMG.NBH
Turn it on and you might get lucky!

Just make sure its stock rom that was supplied, or the updated WM06 version as the CID should check out then...
vwkess forgot to mention, reset into bootloader, hold power, ok button and reset with stylus. Hold all buttons in until you get to the tri-colour screen. If it works, follow the prompts....
Cheers...

hi,
i think i can hlep.
i had recently bricked my phone with a custom wm6 image, it worked fine for two days and then i reboot, and all i see was the welcome image, nothing else.
so what i did is -
i pressed the hard reset buttons - power + OK + SOFT RESET (Stylus), kept it pressed for 3-4 seconds, the fone rebooted, the screen was full with some colored bricks i connected my fone in USB and on screen i saw USB.
I then again flashed my fone with the working update, it worked perfectly for me, try may be you can get some luck
ps - before doing all these, i turned my fone off by removing the battery, i removed sim card and mmc card as well.
regards

That may work too, but again, try to flash with a stock rom, untick "connect with USB" in activesync and then try.
Make sure you go to boootloader screen, instruction in rajivlodha's post, before you connect to the pc.
Goodluck...

I need some help as well.
I think I may have bricked my phone. It's a rooted htc hero cdma. I'm running cyogenmod on it and it was working fine, until using metamorph to apply some changes to the theme.
I went to reboot, and it now it won't load past the htc screen. Even when i try the key combination to put it into recover mode. I didn't install a nandroid backup, and i'd be fine with just completely wiping my phone. help is appreciated.

Dead Wizard, please help

Few days ago my Wizard died all of a sudden. When turned on it only gets to the point when it shows "HTC smart mobility" and stays there. So not even to the screen with IPL, SPL. I tried soft/hard resetting, playing with battery but it was all no go, same.
I can get to the red-green-blue bootloader screen however, shows IPL 3.08, SPL 3.08. If i connect via USB cable to computer, bootloader screen shows "USB" on bottom. The ROM on the device was TNT's (not sure which version), Windows Mobile 6.1. It worked for ages without any problems with this ROM before this.
ActiveSync does not recognise Wizard at all, I cannot establish connection and therefore downgrade/upgrade the ROM becouse upgrade programs (for exmaple with ROM got originally with the device) say they cannot contact the device.
What are my options, please help.

hy
in my opinion , it is normal for active sync to not recognize your phone , because it's not turn on properly ,i mean it only recognize the phone when you enter windows mobile.
if i were you i would try to flash any rom i like and see if it works. i hope this helps

But ROM upgrade/downgrade program requires ActiveSync connection to run and I can't establish it...How to solve the situation, please advise?

when you are in bootloader screen and your phone is connected to the pc by usb cable just start the downgrade/upgrade program and it should work.

i did that. rom update utility complains that it cannot connect with mobile...
that was tried with:
1. official t-mobile ROM that was on the device when I got it
2. CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE ROM
my IPL and SPL versions now are 3.08

sorry , i can't think of anything that might help you.

same problem
phones a brick.
I can get to the bootloader , i can even perform a succesful hard reset.
But it doesnt get recognized by the computer in bootloader mode. is there any way to flash the rom if the computer doesnt recognize the device?
regards

Try this look for nbd v8.1 or v8.3 .
hold the camera button and do a soft reset but keep holding the camera button until the 3 color screen comes up it should sync your phone then run the nbd rom or original cingular ship rom like this one ** RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship_1 ** i prefer original then other but that's me. Hope this help you.

help me - Frozen operator screen, unlocking, flashing and usb connector.

Hey there, just want to say before I tell you my problems that this forum is cool. I recieved a lot of useful information and tools for my phone here. Thanks.
Onto the problems!
Okay so first of all, I was given an HTC Vogue on the Telus network from a buddy because my previous phone fell in the pool. I was having a blast with this phone, 'twas the best thing that ever happend to me.
Now before I get into specifics, I'd like to mention that I've never been able to connect to activesynce because the computer would not recognize the USB cable. I've never been able to fix that problem.
Recently I've been having problems with my phone. Sometimes it would take a little spill onto the floor from my lap because I'd forget it's there or whatever. The back casing would come off and the battery would come out. No worries, I would just pop it back in and off I go. But this time it would boot up to the Telus screen with the buncha red writing.
Code:
M 03
B 01
P DCAAXOM-4350H
R 3.41.00
D 3.07
After that text disappears, the phone would freeze at the Telus screen and either: a) No LEDs would flash b) a yellow LED would come on c) THe phone would be left on that screen and just shut off after a while.
So i did some research and found that I could preform a hard reset. Voila! It worked like a charm and I was off using my phone again, but it had barely been 24 hours before the phone froze and I had to reset. And the phone would revertback to the previous problem. Hard reset would NOT work. It would reset the phone but still freeze. Sometimes it wouldn't even stay on the hard reset, the phone would shut off as soon as I release the SEND button after holding all fo the hard reset buttons. So i went back here and on Google to look for the fix.
I've done a bit of research on possible fixes to my phone like disassembley of the phone and the placement of plastic sheet over a processor of some sort and flashing the ROM.
So what I did was look up some custom roms and what not. From what I understand you need a CID Unlocker before custom roms can be used. I looked around and found that I need the USB connector to work for the phone to become unlocked. But this conflicts with my current situation and whenever I try to flash with a custom rom from the microSD, it takes me to the Loading... screen and stays there without any mention of flashing a ROM. This is also the case when I try to put the CID Unlocking .nbh on my microSD card.
So I ask what I can do for my phone to revive it. I've done extensive searches on any fix to my phone with little or no result. I need some fixes fast because I have a tonne of important calls coming in that I need to answer. I will not accept that my phone is dead.
Please guide me in the direction on how to unlock the CID with a microSD card. Or just anything that'll enable me to use my phone again. I con't afford ot buy another one.
BTW
The info on my boot loader screen reads.
VOGU100
SPL-2.01.0000
CPLD-11

BTW
The info on my boot loader screen reads.
VOGU100
SPL-2.01.0000
CPLD-11[/QUOTE]
I gather that you can get to the boot loader screen by the above info. While on that screen try pluging you cable into a direct USB port on the computer and then into the phone. If your phone is recognized it will change from serial to USB at the bottom of the multi color screen. If that doesn't work let me know.

Also here is a link for the unlocker for the CDMA Touch on PPC Geeks
http://forum.ppcgeeks.com/showthread.php?t=20370

whitey10tc said:
BTW
The info on my boot loader screen reads.
VOGU100
SPL-2.01.0000
CPLD-11
Click to expand...
Click to collapse
I gather that you can get to the boot loader screen by the above info. While on that screen try pluging you cable into a direct USB port on the computer and then into the phone. If your phone is recognized it will change from serial to USB at the bottom of the multi color screen. If that doesn't work let me know.[/QUOTE]
I've tried that. The phone reads USB but the computer can't recognize the phone. Activesync won't work either.
EDIT
I've tried flashing with a stock rom. Everything runs fine in that screen. I soft resetted the phone and it went to the windows mobile 6.1 screen with an orange LED and just sat there, I wanted to wait but impatience got the best of me and I soft resetted and now it gets stuck on the telus screen again. Sometimes the green LED flashes as if the phone was running normally and the screen dims. I don't know whats going on.
I think I've tried that ppcgeeks thing but I can't be sure. It doesn't work because I can't connect my hpone with the USB cable.

My boot loader screen has changed after flashing the stock rom. It now reads:
Code:
VOGU100
SPL-2.01.0000
CPLD-3
same problem after flashing, just different writing on the boot loader screen.

patience
patience is the key.
patience is the key.
If you go to bootload screen connect cable and it changes to USB you should be connected.
Also here is a link to a tutorial
http://forum.xda-developers.com/showthread.php?p=3680838#post3680838
To be sure that your computer is not connecting to the phone plug usb in go to deivce manager and double check the USB if it is not connected correctly it will have a warning sign by that port. Try reinstalling updating your drivers for the usb.
patience is the key.
patience is the key.

beanage said:
My boot loader screen has changed after flashing the stock rom. It now reads:
Code:
VOGU100
SPL-2.01.0000
CPLD-3
same problem after flashing, just different writing on the boot loader screen.
Click to expand...
Click to collapse
You need to flash the SPL 2.31 bootloader

It appears as if it's fixed for the most part. Some minor problems but that doesn't stop the fucntionality of the phone. But I'm still pretty pissed that no matter what i do, my phone will not be recognized by the computer with the USB cable. i've tried everything and looked everywhere. Does someone want to send me the usb drivers for the Vogue? Please don't tell me that i don't need drivers because activesync won't connect. I've seriously looked all ove rthe internet for fixes and none of them work. Any pointers ro anyone want to send me official HTC drivers? I want to start using cooked ROMS.

here you go HTC windows driver will work for the vogoue
http://www.4shared.com/file/94429326/ffb09a5f/WindowsHTCdrivers.html
But unfortunately won't solve active sync problem. I would uninstall activesync and reinstall on your windows XP computer.

Quote from HTC website
Q.
Activesync is not recognizing my device, what should I do?
Be sure that you have not connected your device to your PC before you installed Activesync. If you did plug in your device before installing, uninstall Activesync and start the process over ensuring that you do not plug your device in until after Activesync has been installed.
Verify that your device is recognized by your PC in the Device Manager; if it is not, resolve that issue first.
Unplug your device from the PC for a few seconds and then plug it back in.
Perform a Soft reset on the device while it is plugged into the PC.
On the device, go to Start>Settings>Connections>USB to PC and check the "Enable advanced network functionality.

crap, my phone just ****ed off again. Same deal as before. Hate being broke.

help with vogue frozen loading screen
i unlocked my vogue and flashed NFSFAN 6.5 ROM and now phone freezes at loading screen and will go no further. i can still pull up bootloader thats all. any help or tips would be appreciated. thank you

what is your bootloader version

htc boot up screen and bootloader
m03
b01
acaaam-4070
r 2.26.00
s 3nfs
vogu100
spl-0.41.coke
cpld-3

are you using a GPS ROM if so you have the wrong bootloader and need the 2.31 from this post http://forum.ppcgeeks.com/showthread.php?t=20370.. Install the 2.31 and give it a try.

tried using 2.31 unlocker, when i run the RUU and says it will take 10 min it accually takes 10 sec and installs fast then after my phone restarts bootloader still says .41

You need that SPL 2.31 for that ROM
http://forum.xda-developers.com/showthread.php?p=3680838#post3680838
This is a quote from the facts thread for your ROM
First go here http://forum.ppcgeeks.com/showthread.php?t=20370 and
READ the hell outta it until you have it step by step.
(BTW use the 2.31 unlocker regardless about the GPS thing)
OK, now that you've read that (happy dance time)
Download the 2.31 Unlocker and NFSFANs WinMO 6.5 ROM.

Here is a good link for the boot loader. unlocker.
ftp://up.ppcgeeks.com/Vogue/Users/ImCoKeMaN/Vogue_unlocker_MFG_2.31.exe

yeah still can't get 2.31 to load on my phone. i tried to flash the stock alltell and sprint roms but at 29% it freezes or has recovery issues and will not go past 29%. flashed dcd 0.2.0 and got it to load! bootloader still shows .41 but now when i boot up phone it says in red at bottom of HCT boot screen.
m 03
b01
No radio
d1.17

Who is the original carrier You will need to get that OEM ROM and flash it. Then run the 2.31 unlocker follow the directions you can use the bootloader on the factory rom I have done it with sprint and alltel Vogues. The OEM ROM will reinstall your radio then you canuse the unlocker. The .41 unlocker is for non GPS radio and ROM combinations.