Related
Hi,
No doubt as many others have, I managed to drop my XDAII one too many times (they are a bit to light and smooth).
I think the speaker is no a bit duff as sometimes it stops working and I can't hear the other person. If I press on the circular bevel on the case that hides the speaker it starts to work, sometimes tapping the bevel also brings the speaker back to life.
I wanted to know, could this be a simple problem like the speaker connection coming loose or something more serious where a solder fix will have to be applied?
I think the device is still under warranty so I might be able to RMA it but I wanted to know how easy or hard is to fix this, can it be fixed by me or should I send it in to be repaired?
Cheers,
Taz
I would send it in for repair, once you break the security seal you will invalidate warranty and then you will be in trouble if another hardware failure occurs. It is probably a simple connection problem.
its just likely to be the spring connectors from the board to the speaker which is fixable (details can be found in the forums HERE).
However, the O2 XDAII has a 24 month warranty which i found out in November as i had exactly the same problem and decided to take it to my local O2 shop to have it repaired. It took them 1 week to get it back to me but they told me my unit was irreparable and gave me a reconditioned unit as a replacement. I was not very happy as the case was scratched all over etc and my unit was as new. I complained and asked them to give me a new unit. After a further 2 weeks and 2 more instances of sending it back to the repair centre i eventually got a brand new fully boxed XDAII (second battery, second case, second cradle etc etc) from the O2 shop but not until i kicked off with the manager stating how unprofessional O2 was in repairing/replacing a unit that was under warranty.
NB. New XDAII screens are no where near as good as the original screens when looking at it from an angle. They look fine straight on but colours fade/change when viewed from below or from the left.
Hope some of that helps.
Cheers mate,
I think I still have about a year on the warranty but I heard that the XDAII are no longer in production so I am a bit worried that I may not be able to get it repaired however a pal reckons they should upgrade me to the XDAIIs (I had one, didn't like it).
I will visit my local O2 shop in a few days and kick it off with the manager as well... to get some results of course
Cheers,
Godz
I dropped my fone from the second floor to the first - but luckily the corner of the phone stopped it from hurting the floor any more. It hit the corder where the stylus is and now the screen looks a liitle raised from the keyboard. When I turn it on, it only shows me a white screen.
2 Questions:
1 - can I fix it
2 - can I get another one from Cingular (and how)
I know that I do not have protection on my phone since Cingular will not protect phones that cost more than $300 (when if you think about it, those are the phones you need to protect) Does anyone know how I can get another phone from Cingular without paying?
Thanks
mikeysweet said:
I dropped my fone from the second floor to the first - but luckily the corner of the phone stopped it from hurting the floor any more. It hit the corder where the stylus is and now the screen looks a liitle raised from the keyboard. When I turn it on, it only shows me a white screen.
2 Questions:
1 - can I fix it
2 - can I get another one from Cingular (and how)
I know that I do not have protection on my phone since Cingular will not protect phones that cost more than $300 (when if you think about it, those are the phones you need to protect) Does anyone know how I can get another phone from Cingular without paying?
Thanks
Click to expand...
Click to collapse
getting one without paying isnt going to happen, especially since it shows obvious signs of user inlficted damage. you need to start saving up for your next phone purchase.
So Should I go ahead and try to open it up and see if I can fix anything in it?
In my opinion, I think the LCD is broken, or it could be just the connection loose where the LCD connects to the mainboard. Goodluck!
Clem
clemsyn said:
In my opinion, I think the LCD is broken, or it could be just the connection loose where the LCD connects to the mainboard. Goodluck!
Clem
Click to expand...
Click to collapse
there is a place called www.safeware.com where you can insurace your PDA for about 60 bucks a year... check it out
you may get another from ebay for $400
if the screen and motherboard are not broken, try to get Dopod 838 housing assembly, and replace the housing
So I opened up the entire phone and only found that the InfraRed lens broken off. I don't see where else it is broken. I had everything apart except the screen from the face of the phone. I took off the back by taking the screen off of the guide rails.
I made sure the connections between the screen and the board where secure. With the phone completely open, I tried to turn it on and still got a white screen.
When I plug in the power, the orange light doesn't light up.
I think I'm up a certain creek without a paddle.
Here is an update:
I called Cingular and all they could offer me was the number to the manufacturer HTC (877-878-6944)
HTC sends me to their repair center (888-354-2375)
So I am sending my busted phone to them and here is how the process works:
They get your CCard # to have on file. You send the phone in your own package, your cost. They will get it, diagnose the problem and give you an estimate of cost. If you approve the cost, then they will charge your card for the repair plus $27.80 for return shipping. If you do not approve the cost then they will charge you $27.80 and return you your busted phone.
I'll keep you posted to the cost estimate.
10/26/06 - HTC calls me up and says that my unit will cost $169 to repair and I go ahead and authorize it.
10/30/06 - HTC Ships out my unit and I should get it 11/2
Jesus, 169!
wait wait..u mean to tell me there's no warranty on this device? not even a year?
I don't know how HTC works, but I used to own a couple of HP PDA and PDA phones...and if there's any kind of problem, hardware, software, or even if I dropped the device and broke it (which I did a couple of times), I call the warranty department (of course I had to lie and told them I never damanged it), but then they send me a new PDA on UPS Next day right away with no charge to me..and I send them back my old PDA postage paid....
I don't get it..why can't u do the same with HTC? Like I was wondering earlier...is there no warranty? Coz if there isn't, I'm returning my 8125.
And the Saga ends.
Yesterday got my phone and tested everything to make sure it works. Turns out that they actually do fix what you send them instead of just swapping it out. My case was cracked near the corner and you can see where they repaired the crack.
So there you have it.
- There is a warranty for factory defects, not dropping your phone
anthoj said:
I don't get it..why can't u do the same with HTC? Like I was wondering earlier...is there no warranty? Coz if there isn't, I'm returning my 8125.
Click to expand...
Click to collapse
There is a 1 year warranty through Cingular but it does not cover lose or physical damage, only defects in the product.
My touchscreen developed some issues after about 3 months of use. It was replaced under warranty.
If you drop and break it your warranty is voided. This is pretty standard, insurance covers loss & accidental damage.
Hi all,
I need help,suggestions,anything with an issue I've had for a while. Since the time I started loading WM6 the screen has been randomly fading to white. I have LSVW latest rom 22/4 SE and 1.40.10 radio and 1.40oli although it doesn't matter what rom you load. I tried going back to WM5 and its better but now still fades to white as well.
on advise from oli and legolas I purchased a new battery but still have the same issue.
I have dropped my phone once which resulted in a crack to the right of the DEL/CR keys so could it be a HW issue and if you think so is it one I could open up the phone and fix?
Any and all help appreciated
IN FACT IF SOMEONE CAN RESOLVE THE ISSUE I WILL DONATE SOME CASH TO THEM!
test
Im updating to
LVSW 4-23 Full, Radio 1.40.30.00, SPL 2.10.Oli, IPL 1.04
seeing if any difference comes out.
This is not the first time this issue has been reported:
http://forum.xda-developers.com/archive/index.php/t-301003.html
The conclusion is that it's hardware related. It may be as simple as one of the internal ribbon connectors having a less than firm connection. It may be brought on my anything from physical movement or pressure to internal pressure if the device gats warm. However, it is possible that there is a failing component. IMHO, a case of take it for replacement/repair or first check connectors if your brave and not worried about a warranty.
Mike
mikechannon said:
This is not the first time this issue has been reported:
http://forum.xda-developers.com/archive/index.php/t-301003.html
The conclusion is that it's hardware related. It may be as simple as one of the internal ribbon connectors having a less than firm connection. It may be brought on my anything from physical movement or pressure to internal pressure if the device gats warm. However, it is possible that there is a failing component. IMHO, a case of take it for replacement/repair or first check connectors if your brave and not worried about a warranty.
Mike
Click to expand...
Click to collapse
HHmmm interesting thread .. the only issue i have out of that is the fade to white one.
Maybe Hardware .. i got the phone off ebay and now it has a crack in it .. so i dare say it isnt under warranty any more. (even though its a max of 6 months old).
It may also be software. I experienced the WSOD on my JASJAM when playing with the GPS-related DLL's. Once this problem appeared when switching on the camera. The screen would turn white and soft reset would not fix this, only power off/on would sort it out. Seems that the drivers do not reset (some of) the hardware to a known state on boot.
Had EXACTLY the same problem. Hoped it would be a software problem. Hard-reset a few times to no avail. Upgraded to a couple of the WM6 ROMs. No change. I did notice that when it was cool it tended not to happen, but after being on the phone a couple minutes or using the PDA for a while, it would do it AGAIN.
One weird thing I noticed was that if I did a Soft-reset and held down the Left Soft-key, I could "force" it to fade to white on start-up! VERY WEIRD.
I finally bit the bullet, and sent it back to Telstra to get it sorted. Didn't want to void warranty myself.
It has been just over 2 weeks since I sent it off, and They have sent this reply...
-------
-------
Hi
This phone is currently waiting on a part which was ordered yesterday. Some parts have already been issued but needs further repair.
Regards
Nadine
--------------------------------------------------------------------------------
From: LJ Boyd [mailto:[email protected]]
Sent: Friday, 20 April 2007 2:18 PM
To: ! TMS Customer Service
Subject: RE: Imate JASJAM Problem
Hello, I am emailing about an I-Mate JASJAM phone I sent for repairs early last week (tel # xxx ).
Can you please update me as to status of this repair, as the Telstra shop did not provide me with a second phone while I await return/repair/replacement of the phone.
Thanks,
-------
-------
So, I guess it IS a hardware problem. But then again, that kind of reply, sounds a bit "dodgy" as it doesn't seem to "technical" does it?
Hope this helps.
jyetara said:
So, I guess it IS a hardware problem. But then again, that kind of reply, sounds a bit "dodgy" as it doesn't seem to "technical" does it?
Hope this helps.
Click to expand...
Click to collapse
Their reply was not very technical - does not surprise me however. The people who repair these devices are usually faced with some component/connection/screen or a m/board that needs replaced. They often fail to take account of something as basic as the case pressing on the screen or other components - particularly when device is warm. So they replace the component they think is faulty and then discover the problem is still there. With this issue in particular I think that there are no faulty components just the case is a fraction of a millimetre too tight for the internal components and hence swapping out parts can have no effect. With this fault I advise people to go for a replacement not a repair if possible.
NB: This issue should not be confused with white screen that may appear after installing particular software or when an application crashes, or when the flashing of a new ROM goes wrong! The hardware issue arises most commonly when the device gets warm or put another way goes white after maybe 10 minutes of use and will continue to go white even after hard reset.
Mike
I have this same problem! =(
My phone screen recently (4-5 days ago) started to go white. I never saw this happen with my own eyes but when i picked up my phone and its sleeping i push the power button to get to an all white screen. I can hear noises when i touch the screen but no image other than white. I can solve this by removing the battery and putting it back in, then my scren works fine....its not verry often just like 1-3 times a day.
I want to try a hard reset but have a question first: My phone is unlocked by the ebay guy i got it from, will a hard reset lock my phone back to Cingular?
Next i want to try upgrading my ROM and Radio and anything else...im looking in the wiki for instructions on how to do this. Any help? What else shouls i upgrade?
Ive only had my Hermes for around 2 months so im new to much of this.
THanks!
I recently purchased a Used Imate Jasjam (Ex Telstra Australia) with this issue.
I pulled the unit apart, and reseated and pressed the Power and LCD Display Data Cables... attempting to ensure they were firmly fastened.
I then upgraded to LVSW's Latest WM6 Release.
I have had the Phone go to White once in that timeframe since. I brought it back by pressing the power button of, then one again.
I don't feel that it's really a "100%" Faulty Part... Because it works fine othertimes. It almost seems as if connections or a Data Cable has an Issue.
I'm intending tonight and using the Phone over the weekend to see if the issue continues to occur.
BAD NEWS!!
Well, got my phone back after a bit over 3 weeks I think? I kept ringing the repair center and emailing. Finally they said it was ready, and was sent back to the shop I bought it from. Rang the shop "no it's not here yet, we will ring you"... now the repair centre to the shop is a 20 min drive... on the 3rd, I rang again at 1pm and "no it's not here yet, we will ring you when it arrives." At this point I was really getting p*ed off. So I went to the shop, and demanded, and guess what was AT the Shop?!?!?!
Anyway, after 1 friggin day, I have lost the Red & Green phone buttons! As of tonight the whole bottom section no longer work, and the screen has gone white again.
The repair report listed 3 things replaced...one was a "bezel" another was a "poly" something. I will get the report a list the replaced bits if anyone likes, but their descriptions are kind of strange if ya ask me.
Anyway, I have to send the phone back for repairs again, which could take another 3 weeks +, which I think is completely PATHETIC OF TELSTRA, especially for the fact they dont give the same phone or even similar to "loan" while I wait for my defective $1300 phone to get "repaired"... (more like 'fiddled with' & "yeah, she'll be right mate"...
GRRRRR!!!!
My girlfriends phone was having the same problem. Try popping out your SD card and putting the phone into/out of sleep and see if that brings back a visible screen. Thats how we determined her situation was a hardware problem and not a problem with the rom.
jyetara said:
Well, got my phone back after a bit over 3 weeks I think? I kept ringing the repair center and emailing. Finally they said it was ready, and was sent back to the shop I bought it from. Rang the shop "no it's not here yet, we will ring you"... now the repair centre to the shop is a 20 min drive... on the 3rd, I rang again at 1pm and "no it's not here yet, we will ring you when it arrives." At this point I was really getting p*ed off. So I went to the shop, and demanded, and guess what was AT the Shop?!?!?!
Anyway, after 1 friggin day, I have lost the Red & Green phone buttons! As of tonight the whole bottom section no longer work, and the screen has gone white again.
The repair report listed 3 things replaced...one was a "bezel" another was a "poly" something. I will get the report a list the replaced bits if anyone likes, but their descriptions are kind of strange if ya ask me.
Anyway, I have to send the phone back for repairs again, which could take another 3 weeks +, which I think is completely PATHETIC OF TELSTRA, especially for the fact they dont give the same phone or even similar to "loan" while I wait for my defective $1300 phone to get "repaired"... (more like 'fiddled with' & "yeah, she'll be right mate"...
GRRRRR!!!!
Click to expand...
Click to collapse
Yes, sadly this is kind of predictable as I said in an earlier post in this thread:
http://forum.xda-developers.com/showpost.php?p=1233420&postcount=7
This is why, as I said, get a replacement not a repair if possible. My view is that the individual components are fine but connectors come loose or the heat generated causes pressure to be put on the screen etc So it's a problem with some cases and how the innards in some cases get squeezed. So off course changing the top poly board, connectors, bezel gasket, may by pot luck make a difference but is just as likely to make no difference at all.
Mike
Status Report:
After having my phone playing Video's Through the Night (My Way of a "Stress Test" to Generate Heat) I woke up the find the screen to be "almost completely" White.
Usually its gone completely, however in this instance I was able to see the icons through the whitewash.
I put the phone into sleep and back out and the Display is fine again.
Being that these phones are much easier to pull apart and put back together than my old JasJar I might to do some further experimentation.
I think the issue will have something to do with either one of the following
- Heat
- Pressure on the LCD from Parts Around it
- Faulty Ribbon or Power Leads to the LCD
My suggestions
- In the Case of Heat... I'll run the Same Test, with the Phone Directly in front of a small airconditioning unit I have.
- In the Case of Pressure, I'm going to look and see if I can place some extra Insulation Tape or Similar on the Phone to relieve this
- I wish I could find somewhere to buy the Replacement Ribbon Cables but I don't know where I can get them in Australia... any ideas?
VolarisPtyLtd said:
Status Report:
After having my phone playing Video's Through the Night (My Way of a "Stress Test" to Generate Heat) I woke up the find the screen to be "almost completely" White.
Usually its gone completely, however in this instance I was able to see the icons through the whitewash.
I put the phone into sleep and back out and the Display is fine again.
Being that these phones are much easier to pull apart and put back together than my old JasJar I might to do some further experimentation.
I think the issue will have something to do with either one of the following
- Heat
- Pressure on the LCD from Parts Around it
- Faulty Ribbon or Power Leads to the LCD
My suggestions
- In the Case of Heat... I'll run the Same Test, with the Phone Directly in front of a small airconditioning unit I have.
- In the Case of Pressure, I'm going to look and see if I can place some extra Insulation Tape or Similar on the Phone to relieve this
- I wish I could find somewhere to buy the Replacement Ribbon Cables but I don't know where I can get them in Australia... any ideas?
Click to expand...
Click to collapse
We wait to see. Mind you one guy on these boards found he could get half an hour from his device if he put it in the freezer for a while - so I'm not sure that air-con will be strong enough!!!
Mike
Well Results.....
After pulling apart the unit and reconnected, I think I found my cause to simply be excess pressure.
I've removed the "Black Plastic" Micro SD Card from its Blanking Plate.
Since I've done this... not one White Screen Whatsoever.
I don't use an SD Card, so the issue is resolved for me, however it is very interesting.
Could be Pressure or Heat (Small Hole Might Increase Airflow/Allow for Greater Dissapation or something)
Hi folks,
i've also small experience with this "white screen" issue and just wanted to inform you about it.
I got the device from my former boss who did already complain about this "white screen" issue on his O² XDA trion with original ROM. (honestly i did not really believe him due to my experience with couple of other devices so after i got the device i was just wondering - ok back to the facts).
I installed on Friday the Windows Mobile VI Pro - BLACK 2.5 Release and until today it was running (as far as i remember expect one time) nearly perfect w/o white screens. About 45min ago, i flashed the device with BLACK 3.0 Release and got until now about 5-10 times a white screen.
I assume this is not a hardware ONLY issue but indeed very strange.
I'll go back to 2.5 and will look forward if i get again the white screen or it'll be ok.
Cheers so far
FaCeOff said:
Hi folks,
i've also small experience with this "white screen" issue and just wanted to inform you about it.
I got the device from my former boss who did already complain about this "white screen" issue on his O² XDA trion with original ROM. (honestly i did not really believe him due to my experience with couple of other devices so after i got the device i was just wondering - ok back to the facts).
I installed on Friday the Windows Mobile VI Pro - BLACK 2.5 Release and until today it was running (as far as i remember expect one time) nearly perfect w/o white screens. About 45min ago, i flashed the device with BLACK 3.0 Release and got until now about 5-10 times a white screen.
I assume this is not a hardware ONLY issue but indeed very strange.
I'll go back to 2.5 and will look forward if i get again the white screen or it'll be ok.
Cheers so far
Click to expand...
Click to collapse
You are right to ask the question "is it hardware or software".
1
We know a white screens can arise if folk duff up flashing a new ROM.
2
We know there is a hardware caused white screen that comes and goes often when device gets warm.
3
But there maybe white screens caused by some kinds of crashing software or a buggy ROM etc
Crucially in terms of finding a cure will be distiguishing between these.
2 for most people is easy - take it back and get a replacement.
1 is a matter for the ROM upgrading and fixing boards
3 is a case of trying different ROMs testing 3 party software by selective installation until the problem starts or stops.
In your case I am worried that this is a number 2 device as it did sometimes get the problem before you flashed the ROM and now it's worse. It may only be worse because this particular ROM is generating more heat and consequently more white screens. (see explanations elsewhere).
I suppose if it's an occasional problem you might live with it but otherwise it's replacement at best and repair as a rather dodgy alternative.
Mike
Hey Mike,
well, before flashing the device with a custom ROM, in my opinion it was really difficult to use it.
By flashing it with V 2.5, it was very good usable and with V 3.0 it returned to become more unusable. Nevertheless, i upgraded 10min ago with HARD-SPL-V7 and it's running fine now (i've been wating with downgrading to V 2.5. If it returns to become unstable, i will downgrade to V 2.5 again.
I'll keep you informed.
yes for this particular "white screen" issue it will be useful to hear how things go - thanks
Mike
White screen - in my case definitely a hardware issue
Hi folks,
i was testing and playing around with my Hermes and today i found the problem (very funny because now i can't reproduce it anymore but just read ahead).
Today i was playing around and after pressing by accident on the case of the Hermes, the screen appeared disappeared and changed into white.
Please download the video i recorded from the attached link - you'll see that it was able to reproduce it by tapping on the case:
http://asuka.descipe.de/dphome/test/HTC_Hermes_White_Screen_issue.mp4
Please use VLC or MPC (additional codecs required) to watch the movie.
Honestly i'm not sure if this can be reproduced by anyone but this makes the whole situation much more clear.
Any feedback is welcome.
Cheers
Hi guys,
I need your help. Several days ago, I upgraded my Dopod 900 to Tomal latest ROM. everything works perfectly, even the battery last longer.
Anyway, today, I accidentally drop my Uni to my feet (from around 1 meters high). The screen turns white.
I tried soft reset and hard reset, still white screen.
But the PDA itself is okay because when I connected it to PC, I can browse the Uni without problems. I even can confirm the hard reset is succeded because I check with Jeyo Mobile Companion, contacts and SMS in my Uni already deleted (meaning the hard reset works fine).
What should I do?
Your LCD already damaged. Replace new LCD.
not broken connection or something?
To have a good veredict why don´t you read the user manual of the Uni, is located in the Wiki, that way you can check if it´s a connection or something else
Good luck,
It is possible that the connection is loose at the board level. You might have to re-attach, if that fails - replace the screen. Fairly straightforward procedure, but consult the Service Manual for correct disassembly steps, as there are some tricks involved, seen many cases broken because someone was not aware. Only the screen part needs to be opened, not the main body. Good luck.
ok, i'll try it. thanks guys.
i probably have to ask help from a technician though, since i'm not good at fixing electronic thing
ok, I downloaded the manual.
but since i'm no technician, i have to find one first, probably next week.
anyway, just to update the case.
It seems that not only the screen are turning white, the Yes/No Call button and the speaker are dead too. I called my Uni from other phone, connected successfully, but the Uni doesn't ring and the Yes Call button do nothing (the other phone still waiting the Uni to pickup the call).
So my diagnose for the time being is that the flexi-cable must've been broken somehow.
Hope I don't have to replace the LCD 'cause I don'y have enough money right now.
well, ended up brought my Dopod 900 to HTC/Dopod service center.
turns out the flexi cable unplugged. so i only need to pay service fee which is only $5.
I guess it's worth it, i mean, if i open the device myself, i would have spent the $5 to buy the necessery tools, not to mention that i'm not electrician and might damage my device in the process.
XA-R01 said:
well, ended up brought my Dopod 900 to HTC/Dopod service center.
turns out the flexi cable unplugged. so i only need to pay service fee which is only $5.
I guess it's worth it, i mean, if i open the device myself, i would have spent the $5 to buy the necessery tools, not to mention that i'm not electrician and might damage my device in the process.
Click to expand...
Click to collapse
Excellent Glad you got it sorted
the touchscreen element of my [email protected] has seemed to stop working.
I think that another point of the screen is in contact becase when i have got to work (through squeezing certain areas of the screen and then letting go) it seems to show the same as doing a two finger touch (zooming etc)
anyone else had this and do you think it's covered under the 12 month warranty?
there's no scratches on the screen at all or obvious defects
same proBlem here ..
My HD2 showed an expanding darkblue hint of colour (somewhat the same when you press very hard on a lcd) from where I pressed, just only once. Few days later the touch was failing randomly, increasing day after day.
Thought it had to do with al the radio- spl- hspl- and rom-flashing that I was trying on my device.
It didn't give me too much trouble untill it completly vanished in a matter of 5 minutes.
I had it laying on a table, responded to an incoming sms, placed it back on the table, about 5 minutes later I got another sms, but all the touch was gone so never ever read that message.
Was able to put everything back to original (SPL + Radio + ROM), went to where I bought it and 2 weeks later I could pick it up again with the screen replaced and also HTC-Service installed the new update that was released (the Dutch version) while my HD2 was being repaired.
My touchscreen digitizer failed a couple of months ago. Apparently it was common in earlier models. A quick google search (other search engines are available ) will reveal a few horror stories about how HTC had rushed the development of the capacitive touchscreen and rushed it to market, with loads of devices being returned due to this very same problem. It is covered by your warranty though, which you should find is 24 months and not 12.
HTC were really helpful with me actually. It took a while to get back, but they give you a ticket number so you can track the progress all the time, from receiving your device, testing, repairing, sending back etc. And they even send a UPS courier to you to pick it up from you. You will need your serial number and IMEI when you call, and they'll ask you to package it up in suitable packaging, such as the box it was received in in the first place. They'll only need the actual phone itself, so you can remove your battery, sim card, memory card, battery cover etc. They just need the front bit, so the rest of the box should be empty, apart from your receipt of course, which needs to be a maximum of 2 years old and if it has a name and address on, it needs to be yours, as, if you bought the device second-hand, the 2 year warranty is non-transferable. It is only valid for the original purchaser.
Hope this helps. Also remember to revert to stock rom and spl if you've flashed hspl and a custom rom as your warranty will be deemed void. I know it's not a nice thing to have to send your HD2 away, but I had no choice and it's all back in one piece and working perfectly now.
Good luck.