Trinity Lock!?! :( - P3600 General

Hello everybody...
I'm a newbie in this PDA world.
I've used a tool to SuperCID my HTC 3600 to be able to load the new Official ROM from HTC Asia headquarters the RUU_Trinity_DOPODASIA_WWE_3.00.707.18_6275_1.46.30.11_108_Ship
It was working fine until yesterday when I was trying to put the password locking on the device.
I put password twice as suggested, then reboot the PDA to test it, and now every time a put the password I get the message 'Wrong password' and I'm not able to start the device!!!
I'm prety sure that the one I'm trying is the correct one but I cannot unlock the device... Another problem is that any ActiveSync connection is blocked by the 'Device Locked' message, so I cannot load a Clean ROM as well.
Any suggestions???!!
Tanks in advance
HELLO again everybody
I've made a Hard Reset... and... at list my HTC is back with the defaults ... BACK

Related

My SVP M600 phone got stuck at Starting screen

Hi Friends,
My new mobile phone SPV M600 got stuck whil starting showing four lines of messages as shown below.
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 2.10.1.22
Can any one please help me in geting my phone to today's screen.
I also attached the screen shot for reference.
did you try a hard reset ?
Ya I tried both hard as well as soft reset but same screen is stuck again and agian.Can any one please help me in this regard as I am very new to PDA family.
Ok, first things first:
Since you are new to this, are you sure you preformed a hard reset?
It is done by holding power + camera + comm manager buttons (one on the right, two on the left) and pressing with stylus in the reset hole at the same time.
A message should appear asking you to press 'send' (green phone button) to confirm reset.
If this does not help, you may have a serious problem.
Please answer the following:
Is the device fully charged?
Phone will fail to boot if the battery is too low.
Did you install any software right before this happened?
This should have been resolved by hard reset, but just in case I am asking.
Did you change the ROM, attempted CID / SIM unlock?
This could require more serious measures than I can advise on.
I did exactly the same thing which you mentioned.But even then it is stuck at the same screen.
Ya u r right I unlocked my mobile using a software from eBay.The unlock was successfull and I tried to insert T-Mobile sim, it also captured the signal and I was able to make and recieve calls then after that I wantedly switched off the phone and then tried to start it, there got the problem.
Can any one help me in this regard please.
I am having the same problem, but my phone is not sim-locked.
I've got the same problem after attempting smart1_wm6_pp8mb.exe
I'm having the same problem with my G4 QTEK S200:
Attempted to upgrade to WM6 Rom using smart1_wm6_pp8mb.exe
After reboot the phone got stuck at the QTEK Screen
Tried Hard Reset (Camera+Power+Comm+Reset) followed the steps with the same results (bricked)
I also tried re-flashing the rom back to the factory one using RUU_Prophet_220734_2207114_024721_QtekWWE_Ship and ROMUpdateUtility-NoVendorID.exe in Windows Vista with WMDC (Windows Mobile Device Center v. 6.0.6873) and the phone in boot loader mode (tri color screen) with working USB cable, with windows firewall disabled and symantec AV disabled as well, RUU keeps saying error 260 "the update utilitiy cannot connect to your pda phone..." .
Do you think I should try this process using XP instead? No matter what i try i keep getting the error 260
Any help would be greatly appreciated
Got it fixed!
it was definately a Vista issue. once i tried it in XP with ActiveSync it worked like a charm and i got my phone back up and running. also used spb backup and restored all my settings.
ipl/spl screen
i got the same problem with new rom wm6, and the 260 eror, my problem is that i have xp and the activesync does`t connect ...
... means i cant redo the original rom ????
PLEAAASEEE HELPPPP !!
Again My phone SPV M600 got stuck at IPL/SPL screen
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
yekanth said:
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
Click to expand...
Click to collapse
A rom reinstall on xp solved my problems on that one. retry a couple of times! It may not work the first time! hard reset as well...
Try an official wm5 rom just in case
good luck
Can you please gimme step by step procedure
HI Phil,
I am new to these kind of installations . CAn you please Gimme step by step procedure for ROM installation.
mine is now also stuck, after trying to install new rom. wont connect to active sync either, have i fooked it? tried hard reset etc.
thanks
(with a turned off phone, press and hold camera button then insert USB cable)
then flash provider ROM
RECOVERING FROM ERROR IN STEP 8 WM5->WM6
1. Don't panic
2. Don't panic
3. Unplug the phone
4. Reset with stylus,and keep the Camera Button pressed.
5. A 3 color screen will appear(Bootloader Screen)
6. Connect your device with your PC,and run the NVID(no vendor) WM5 rom.
7. The device will be resetted after RUU(rom update utility)finishes
8. Repeat the WM6 upgrade,from STEP 5..
Click to expand...
Click to collapse
from here http://forum.xda-developers.com/showthread.php?t=310452
hi jay
i seen your post in n00b guys one, i fixed it!!!!, thank you so much, i couldnt remember how to get it to those 3 colours.
thanks again
Colin
Hi Iam unable to get the NVID ROM
Hi,
I am unable to get the NVID ROM. The Rapidshare link that has been provided in the other thread is not working. Can some one tell where can i get the ROM.
collywog19 said:
i seen your post ...
Click to expand...
Click to collapse
no problem mate.
..and yekanth i see what u mean about the dead links. i have the files on my computer at home but i'm posting from my prophet right now, so i can't upload. Try using the "pdaviet temp" from one of the wm6 threads?
(http://rapidshare.com/files/54265407/Prophet_PV_Temp.zip)
Hi Iam able to update the Rom but no use
Hi,
To mention my phone is from orange-UK. I got the orange rom from our FTP site and did the flashing/update what ever you say.But still it is getting stuck at the same IPL/SPL screen. Iam very much worried that I will not get a proper solution for my problem.It will be very grate full if some one resolve my problem.
just seems strange...how did you fix it last time? did it just start working again? A random guess would be that the camera button got liquid spilled on it or is stuck in.
If the camera button is pressed in the phone will go to 3 colour screen every time it is turned on.
It won't do any harm if you try to press/move that button to see if u can "unstick" it, not likely I think but u never know...

O2 Orbit crashed after PDAMobiz_Dopod_P800W_AKU301_v1.1.0_Lite upgrade attempt

HI all,
I'm desperate...
I recently bought an 02 Orbit that was supposed to be unlocked.
So I downloaded PDAMobiz_Dopod_P800W_AKU301_v1.1.0_Lite.exe, unpacked it and double clicked on UpgradeRom_P800W.bat
A dos installation routine started, then I performed a hard reset by pressing the softkeys + stylus reset.
and now I"m stuck on the O2 logo, with some red informations written :
IPL 1.25.0001
SPL 1.25.0000
GSM 02.67.90
OS 1.28.0.0
but nothing else, the device doesn't boot :-(
I'm completely desperate... I had my Orbit working 1h only and now I still have my eyes to cry.
I've tried to install another ROM like ART_HTCWWE_11240501_026790_WWE_Ship, but when I launch ROMUpdateUtility.exe it says that no device is connected....
I tried to enter the bootloader but I don't understand how I could do that (by the way what do you guys mean by the record button? where is it?)
Could someone explain me how I can recover my crashed device please ?
Thanks in advance
ok I've found the record button and managed to enter the bootloader (red-green-blue screen right?). But it doesn't help. My device is not recognise by my PC anymore, no connection.
The problem is that I didn't make the procedure on IMEICHECK because the vendor said my Orbit was already unlocked. I know, I'm stupid, I should have....
Anyway, now I've my 30€ UNL file,
I've edited a ROM with the hex program, I've change "BsaD5SeoA" with "IMEICHECK save exe file" (I told you I'm stupid, or I didn't exactly understood what you mean, because I don't have any IMEICHECK.exe file)
I tried to launch a ROM upgrade but my device still not be recognised by my computer, even in bootloader mode.
Same **** when I try to launch the C3v1Unlock, it says no device connected.
Please, if you have anything to help me......
After i read this THREAD who explain how to repair my problem ...But it dosent work for me
When i want to flash it, it tell me :
INVALID MODEL ID ,with : RUU_Artemis_DOPODASIA_WWE_LOVE_1.28.717.1_INFINEon gsm4.1.13.30_02.69.90_Cmp_Ship_R.exe
INVALID UPDATE TOLL ,with : _ARTE_DOPODAU_12570702_026990_WWE_SHIP.exe
And after have made the TUTO !
Click to expand...
Click to collapse
I saw this post on an other thread... I am having the same problem... I bought artemis from ebay and the seller told me that it was unlocked... But i can't flash it with these ROMs... Did you find a solution? Is it really unlocked?
By the way when the window that tells me "INVALID MODEL ID" shows up at the bottom and to the right of the window there is i big number... Do you know what this is?
Same problem here
I have THE SAME problemhere. The same message on the boot screen. It seems that we are not able to use our XDA ORBIT ;( any more
At least we can download oreginal XDA Orbit english or German ROM OR if someone write RUU for Xda Orbit. Than would be easy - you just go to boot loader and you start your RUU, or easily put .NBH file to your micro SD and flash it from micro SD.Too bad I can just cry over my Xda Orbit. PLEEEASSEEE HELPPP
I also heard that FTP ROM site is going down ---- XDA GENOCIDE!!! What ARE you doing people!
Try the orbit ROM on ftp if it is still there
When a seller says a device is unlocked, all they mean is that you can use any sim card of your choice. To be able to flash another rom you need to CID unlock it. For the Orbit/Artemis family we only have imeicheck selling the program for unlocking cid.
My advice would be to look for the orbit rom on ftp. If it does not work, check with imeicheck if their program works when device is in bootloader mode, and pay them and download the specific application for your device. Good luck
I had a problem with my Orbit when I tried to change the Rom to the PDAMobiz one. I ended up recovering it by...
1 - Hard Reseting it.
2 - Connecting it up to the PC then running C3v2Unlock note v2 from the the IMEICheck site. This made the screen on the Orbit go bright white.
3 - Downloading the the Rom listed in this thread and following the instructions with in the same
It means that my Orbit is seen as a HTC P3300 but it feels quicker. You do need the UNL file from IMEICheck to keep it unlocked. But it worked for me.
Yes I tried everything in bootloader mode,
the C3V2 Unlock program launched but after detecting the device, it says my device is corrupted with a kind message "[probably by your fault]" ;-)
So guys, everyone who's trying to upgrade : CID UNLOCK YOUR PHONE BEFORE DOING ANYTHING, and carefully read the (excellent) tuto.
FYI, here's the discussion I had with Imeichek guys :
------------------------------------------------------------
Hi,
I'm a little desperate and I hope you'll be able to help me...
I recently bought an 02 Orbit that was supposed to be unlocked (I didn't know the difference between SIM lock and CID lock)
I understood, too late, that I should have ask for my UNL file prior to do this stupid "direct upgrade" I did...
Here are the facts :
1- I didn't follow the instructions found on http://forum.xda-developers.com that explained how to order the UNL file and Unlock the device unlocked
2- I downloaded a new ROM (PDAMobiz_Dopod_P800W_AKU301_v1.1.0_Lite.exe)
3- I unpacked it and double-clicked on UpgradeRom_P800W.bat
4- A dos installation routine the started, then when asked, I performed a hard reset by pressing the softkeys + stylus reset.
now I"m stuck on the O2 logo, with some red informations written :
IPL 1.25.0001
SPL 1.25.0000
GSM 02.67.90
OS 1.28.0.0
but nothing else, the device don't go further
I've tried to install another ROM like ART_HTCWWE_11240501_026790_WWE_Ship, but when I launch ROMUpdateUtility.exe it says that no device connected.
I managed to enter the bootloader but my device is still not be recognised by my computer (not connected message). I tried your C3v2Unlock tool but it says the same : NOT CONNECTED
So please, if you have any information or procedure I could try to fix my device, I would really, really, appreciate, especially after my 30€ contribution ;-)
Best regards
---------------------------------------
2007/2/17, [email protected] <[email protected]>:
Hello,
NO PANIC. You can fix the device. You have to find the CORRECT / a matching ROM for your device. For this you have to know what ORIGINAL phone it is (O2 Xda Orbit UK?)
Tell us what device it is and we try to assist you in fixing it.
Regards,
IMEI-CHECK Team
-----------------------------------------------
Thanks for your fast answer!
Yes it's an original phone, a brand new O2 Xda ORBIT, in box
Regards
Thomas
----------------------------------------------
Hello,
the language is important. Is it UK version?
Regards,
IMEI-CHECK Team
-----------------------------------------------
yes it's a UK version
-----------------------------------------------
Hello,
hmm, sorry to tell you but for the UK version there is no official ROM update available right now.
All you can to do fix it NOW is to send it to repair (service center).
For our customers we offer to fix the device for free (you only have to pay for shipping costs in both directions). We are located next to Glasgow UK. In case you are interested let us know.
Regards,
IMEI-CHECK Team
-------------------------------------------------
Ok,
I guess I don't have any other choice.
Wich ROM will you install if there's no official O2 Rom ?
What is the procedure, what's your adress, and how much will cost the return ?
Thanks a lot
Thomas
-----------------------------------------------------
Hello,
- we can install any ROM of your choice (it only needs to exist)
- we also will unlock the device and you can install ANY ROM you life afterwards
- the device needs to be opnened to use some special hardware to access the flash chip directly
- shipping back to (UK/EU) with INSURED Royal Mail is apx. (7 GBP/15GBP) depends where you are located.
Regards,
IMEI-CHECK Team
---------------------------------------------------------
ok thank you,
but will you be able to flash an O2 Xda Orbit with the french ROM that comes with the (Artemis) HTC P3300 sold in France ? this is exactly the same machine.
Regards
---------------------------------------------------------
Hello,
yes we can flash ANY available ROM to it.
Regards,
IMEI-CHECK Team
----------------------------------------------------------
here I am,
I guess there is nothing else to do.
First I want to thank you all for trying to help, then thanks to IMeicheck, they replied very fast and found a solution, even if I won't hae my Orbit for several weeks.
2- I downloaded a new ROM (PDAMobiz_Dopod_P800W_AKU301_v1.1.0_Lite.exe)
3- I unpacked it and double-clicked on UpgradeRom_P800W.bat
Click to expand...
Click to collapse
Maybe you should not have unpacked the file Just clicking on the file icon starts the procedure, which does some checks before actual upgrade starts.
I have switched so many times between the pdamobiz roms and the HTC one so many times I've even lost count
It's been easy for you... because your phone was CID unlocked ;-)
Well i had HTC ROM and now i have pdamobiz... That means that my artemis is cid unlocked???
my orbit is stuck on boot screen exactly as manples'. i tried to flash pdamobiz custom ROM. i can enter bootloader. can u tell me plz to what change "BsaD5SeoA" with "IMEICHECK save exe file" from imeicheck i've got c3v2unlock.exe & unl file. i tried flash it tru sd card-nothing. I've got o2orebit (ARTE200) please hlp
Psrejic, does your Orbit work again? I have the same problem. Can't get passed the splash screen because I flashed it with the PDAmobiz rom.
Only way to go is thrue bootloader. Did the SD flash work for you?
Same problem here Waiting for any solution ...
Only solution so far is imei-check service, witch will cost you: Price of sending to them: (UK) Then 20£+15£(aprox) to pay them for unlocking and repairing + sending back.
That's what I've done,
I received an email where they confirmed the reception of my device and that they flashed it with a new Rom. My device is supposed to work, it's great ! can't wait to try it.
Hi manples ...
You send it to imei-chek?
My Orbit works again! ... but not with a software solution.
I returned the phone to the O2 shop and they gave me a new one immediately. I didn't mention my PDAmobiz Rom upgrade offcourse.
It isn't the nicest way to deal with the problem, but when o2 flashes the rom on the phone they can sell it again.
Then I did the Imei-check solution. Worked and flashed the dopod rom on it.
hi to all yesterday I was your siimilar problem (I've try to install teh powermap rom...) so my Orbit O2 (original german rom) still only in boot screen, today I've try to install this magic rom:
art_tmouk_11311001_024990_wwe_ship.rar
I've press the comm manager button + power button + soft reset and my orbit it's enter in bootmanager mode so, i've install the TMobile UK rom (I was the O2 german rom...)
only in this mode my orbit work again.
bye
xda orbit stuck
i flashed my xda o2 orbir german rom with PDAMobiz_Dopod_P800W_AKU301_v1.1.2 and now it wont start at all i tryed to enter bootloader but i cant ( voice key and reset ) its stuck at o2 logo and :
IPL 3.04.0001
SPL 3.04.0000
GSM 02.00.90
OS 1.20.0.0
DOSE ANYBODY have a solution ? please help me !
keep up the good work ! thanks

Reseting unlock password

Hi to all!
I`m new in this forum and ba world.
Last week purchased spv m2000 with wm2003se and simlock. After reading wiki I unlocked SIM, unhided an unlocked EXTRom , resized DOC and upgraded to latest radio rom and wm6 (thx Helmi for great job).
I did also some set up things in wm6, for example password (something like - "if device is unsed for 30 min. you must insert password") same as my PIN.
My battery after whole day of exploring new features and programs became week (10% - you may loss your data..., etc) and I decided to push power button and replace with another one. But I forget that other one is also week (5%). After soft reset and booting wm6 asked me for a password to unlock system - and I was surprised coz wm6 told that password is incorrect - apparently lost all my settings.
Hard reset and boot options helped with sweeping whole system. So I must now install again all programs and patches.
I don`t know if this is normal wm6 behaviour (I`ve read wm6 is data lost proof - this feater was major cause of upgradind) or I did something wrong with switching batteries.
Best regards
I do confirm this problem.
If unlock password was set,after you changed the battery,in the first boot the phone would be No radio,so you should reset it again.Then the problem came,all the password you typed was incorrect,you could not get into the desktop.
Even after you hv hard reset your phone.You will also need to clean the registry,that is incredible.
Can any one figure out it?
It is a serious problem.
Same problem
I have just the same problem that with my PDA2k. I upgraded to WM6 and put in a Phone Password. When I came to reboot the device and enter the password, it was not recognizing it ( tried to hard reset etc but still got stuck on the Password screen no matter what I do?
Any help on this pls pls?????
thanks
MercuryCube
Trinity P3600 have this problem too
Hello, I just got the same trouble on WM6 Trinity P3600 (AXL ROM from 2007-08-30). So possibly this is common DOPOD ROM bug?
Also have the same problem with XDA IIs. Tried to reload the new ROM but the enter password is still there. Any other solution?
Solution Found!
You find the solution here:
http://forum.xda-developers.com/showpost.php?p=1164331
)
Thanks it worked perfectly
100 points !!!!
this is called hard reset it wipes all of your installed software and settings. it is like freshly installed windows
Dear Xplode , what on earth is the reason behind the blocked password and reseted clock if u remove the battery ? ( backup batter working ). Another question , any idea if i can use a 3rd party application replacement for the Lock application ?
Karim.
prophet upgraded with wm6 hv this problem too
One easy tip
Before you replace the battery, turn off security lock on device. Works for me and is not too.... much hassle.

plz help

My heads spinning from all the information aka post and threads, but im still stuck like my wizard on the 2nd splash screen.
I wasnt trying to upgrade the rom jst clear storage but after everything ive read i would like to upgrade to wm6 but first i want to get my wizard working.
I tried backing up the rom to the sd card but I get "You didn't get the proper security level to download a specific image" So i take it my wizard is cid locked.
My IPL:1.01 and SPL:1.06 does that mean its a g3. My activesync 4.5 doesnt pick up my wizard is it because it cant boot, i tried with it in bootloader mode still doesnt pick it up.
So plz point me in the right direction to fix my wizard
ok i think the place where im stuck at is cid unlocking my wizard with out using that imei site. any help or is there another way to do this.
This helped me when I was stuck on the first screen. For some reason, the Radio file was gone. Follow this exactly, it works. In my case (sounds like yours also), at the end of this you will at least have access to the phone again.
http://forum.xda-developers.com/showthread.php?t=276963&highlight=bootloader
After your done. You will have a RGB screen, then follow these directions to load a base rom and unlock so you can keep going until you ca load WM6.1.
http://wiki.xda-developers.com/index.php?pagename=Wizard Windows Mobile 6 for newbies
I've had many, many problems over the last 3 days trying to do this. I completed it all in less than a day, but when I used the phone it had terrible reception. I completely downgraded everything back to square one. Still bad phone reception. I was about to through it out the window, when someone called my wife's cell phone and she also had bad reception. I then put my sim in another phone, same problem. Well, at&t has a tower down for the last 3 days. What timing, it seems to work when not at home, but hard to test that way Anyway, moral of the story is. Don't give up, keep plugging along.
Good luck.
I'm pretty sure imei checker is for SIM unlocking.
For G3 CID unlocking and upgrading read the stickies in http://forum.xda-developers.com/forumdisplay.php?f=289
If you can start your Wizard in bootloader, and it says "usb" in the lower-left, you can flash your original ROM. An active sync connection is not needed. Search for your carrier's ROM if you don't have it and I'd recommend the "no carrier ID" version of the RUU.
Have you tried a 'Hard Reset',hope it'll work,if it boots up into working OS and it already has IPL/SPL 1.xx,use lokiwiz02b tool to SIM/CID unlock the phone and than upgrade.
If it doesn't work still after Hard Reset,most probably,its Extended_Rom is corrupted,its required to reflash a new rom.
Activesync doesn't work in absence of a working OS and in Bootloaders mode.Its not required for flashing a rom.Just get the phone into Bootloaders and hook the phone with pc via usb cable and watch small usb appear at the bottom of the bootloader screen,if its there,it good to go and flash the rom.
ok so i downloaded the button rom finally but how do i flash it to my wizard.
Get your phone in Bootloaders,hook up the phone with pc via usb,watch small usb appear at the bottom of the Bootloader screen,if its there run the 'RUU' application,it'll start to flash,it stops at a certain percentage,don't get worried and do anything,after a couple of minutes it starts again,let it complete 100%,the phone'll restart and boot up in new OS.
which ruu application. I jst downloaded 1 which comes in the form of a rar file saying ruuwrapper. is that the right 1
So after lots and lots and lots more reading i realized i dont need a ruu. all i need to do is get into bootloader mode plug in the usb and run the wizard button rom. It worked perfectly my wizard is back to life yip pee.
Anyway i wud jst like to thank u guys for all the help and compliment u guys on a gr8 forum.
Now my next challenge is wm6 with touch flo.

Unlocking problem.. virgin mobile

Hello XDA, recently bought myself a leo. I turn the phone on it displays the loading screen etc, then the inital HTC Sense screen, it then immediatley goes to a page saying "Network is locked, please input unlock code"
Now i've tried to code on my sim, no dice, i've reset the phone to factory and tried it, no luck. I phoned virgin and they said its a faulty device and i should exchange it.. Now being my birthday and im inpaitent i don't wanna wait for them to change it.. is there a way i can flash the ROM or something? Doesn't in need HSPL installed?
Any help would be appricated.
My HD2 on Virgin came totally unlocked (can use any SIM) with standard HTC ROM.
Does sound like yours has a problem.
hmm, weird so theres no way to get around it?

Categories

Resources