Related
My friend's jamin when he tried upgrading with smart1 wm6
after the flashing process finished it gives the 3 colors of boot loader
the screen flickers continously with the 3 colors
no way to hard reset the device
and activesync doesn't feel it
I searched all the forum for a problem like this but I didn't find any
any suggestion please, or any help?
Flash NVID Rom and try Smart again. Read WM6 upgrade Manuel and readme for the ROM.
NetrunnerAT said:
Flash NVID Rom and try Smart again. Read WM6 upgrade Manuel and readme for the ROM.
Click to expand...
Click to collapse
Please how can i flash with the activesync doesn't notice my device and where's NVID Rom
Ok. I'll search for it but please help how can I flash it to the device which doesn't recognized or felt by PC
If your device is in bootloader mode, activesync cannot recognize it but this is normal. Jamin is recognize only as a usb device and you can downgrade it to NVID rom easly.
Then you could upgrade your favorite rom, I suggest PDAVIET 4.0.0.1
Bye for now
divxmaniak said:
If your device is in bootloader mode, activesync cannot recognize it but this is normal. Jamin is recognize only as a usb device and you can downgrade it to NVID rom easly.
Then you could upgrade your favorite rom, I suggest PDAVIET 4.0.0.1
Bye for now
Click to expand...
Click to collapse
I think I didn't discuss the problem well
The Problem is when I start to flashing a rom a message tells that check if the usb is connected and if the device is connected .
This is happen with the device is connected to the cable and the tricolor screen is flicking . and the device doesn't open doesn't flashing.
must use NVID rom. maybe qtek nvid one from here? http://wiki.xda-developers.com/index.php?pagename=Prophet_ROMs
hasanemara said:
I think I didn't discuss the problem well
The Problem is when I start to flashing a rom a message tells that check if the usb is connected and if the device is connected .
This is happen with the device is connected to the cable and the tricolor screen is flicking . and the device doesn't open doesn't flashing.
Click to expand...
Click to collapse
If the problem still there, Try to release the battery for 1-3 hours and put it again to the device, go to the boot loader and pray. Hopefully it could work. Actually, this way worked on my Himalaya and Prophet.
Just run the "Step 1" component of the PDAViet ROM (http://rapidshare.com/files/32728615/Prophet_PDAViet_Step1.zip), which is just a plain AKU 2.20 NVID. This will find your device even if its in bootloader mode (it doesnt depend on activesync). Just flash it with that sucker and you should have a working phone on WM5, then you can safely upgrade it to WM6 (or leave it if you like).
ekto said:
Just run the "Step 1" component of the PDAViet ROM (http://rapidshare.com/files/32728615/Prophet_PDAViet_Step1.zip), which is just a plain AKU 2.20 NVID. This will find your device even if its in bootloader mode (it doesnt depend on activesync). Just flash it with that sucker and you should have a working phone on WM5, then you can safely upgrade it to WM6 (or leave it if you like).
Click to expand...
Click to collapse
I shall try and tell you the result
error 260 this is the result
i have a slight variation problem like this...
1. i was upgrading my O2 Neo to the latest WM05 & the phone went to bootloader mode & the upgrade started searching for the phone as normal..then some error & it stopped upgrading while the phone was in bootloader mode..
2. at that time,i got an urgent call & had to leave the phone in bootloader mode...
3. when i came back..the phone was dead & now it wont startup at all.. not even in the bootloader mode.
4. Maybe the batteries dead...so i charged it (Over night)..nothing happened in the morning..
5. kept the battery removed for about 5-6hours & still nothing happens..it simply does not startup.
6.I've tried holding the camera button & resetting, but it wont go into bootloader mode.
7. i;ve tried holding the connections button + camera button _ reset but it wont hard reset...
can anyone help me here...
what can i do???
hasanemara said:
error 260 this is the result
Click to expand...
Click to collapse
Error 260... If i remember correctly that's "cant find device" or something.
Few things to check:
Is the PC you are upgrading on running windows vista?
If so, use a different PC running windows XP.
Have you tried a different USB cable?
If not, do so, this tends to be the cause of problems like this.
Have you checked device manager?
Go to control panel, Administrative tools, computer management, device manager and see if you can find your device. If it has a yellow ! icon on it or is listed as "Unknown device" or anything like that then you may need to reinstall the drivers (int hsi case the easiest way to do that is to reinstall activesync). If everyhting is working properly it should show up as "HTC USB Sync", "PocketPC USB Sync" or something like that under the heading "Mobile Devices".
Have you just plain tried another computer, regardless of the OS?
I found that I could never get my phone to flash on my laptop, but it worked without a problem on my desktop. This is not to say laptop's cant do it, it simply means some computers just have problems like (in my case i believe) no USB 2.0, or too low-powered USB ports.
ekto said:
Error 260... If i remember correctly that's "cant find device" or something.
Few things to check:
Is the PC you are upgrading on running windows vista?
If so, use a different PC running windows XP.
Have you tried a different USB cable?
If not, do so, this tends to be the cause of problems like this.
Have you checked device manager?
Go to control panel, Administrative tools, computer management, device manager and see if you can find your device. If it has a yellow ! icon on it or is listed as "Unknown device" or anything like that then you may need to reinstall the drivers (int hsi case the easiest way to do that is to reinstall activesync). If everyhting is working properly it should show up as "HTC USB Sync", "PocketPC USB Sync" or something like that under the heading "Mobile Devices".
Have you just plain tried another computer, regardless of the OS?
I found that I could never get my phone to flash on my laptop, but it worked without a problem on my desktop. This is not to say laptop's cant do it, it simply means some computers just have problems like (in my case i believe) no USB 2.0, or too low-powered USB ports.
Click to expand...
Click to collapse
No I didn't change any and I can connect my o2 xda mini to the same cable
I want to ask few technical question
HOW CAN A SOFTWARE DAMAGE THE DEVICE?
CAN A SOFTWARE FOR EXAMPLE BURNS A PROCESSOR OR SOMETHING LIKE THIS?
If So there will be a big problem with those types of devices
a virus for example can destroy my device's board or processor!!
Yesterday My friend went to an I-mate customer service who tel him that
the board had been destroyed by the bad software !!!!!!!!!
Please Give me technical advice about this problem
and is there a web site for him to buy this board (i-mate jamin)?
I've tried everything... even tried it on my desktop... but my phone just wont turn on now. i've kept the battery removed for more than 8hrs now... i've even charged it for more than 8hrs non-stop..nothing happens..
maybe i should get hold of a charged battery & try it with that battery...?
Any clue how to get my phone started??
got it working !!! PHEW... i used my HP battery which was charged & put it into it..now i've got my bootloader & i'm installing the new OS as we speak... 15% done.... keeping my fingers crossed
done.. got my HP Ipaq battery , which was charged & my new started up in bootloader more.. PHEW !!!
66% done... keeping my fingers crossed
ok, installed...now, one more problem..my touch screen's not working...???
Any idea what to do?
i installed "Prophet_PDAViet_Step1"
Guys,
I ve just downloaded this http://rapidshare.com/files/21256078..._DUT_11500.rar romversion in the understanding that it was for the HTC 9000 PDA. There was a file called MaUpgradeUt_noID.exe which I let 'upgrade' my 9000. However, I think something very VERY big went wrong! A reset by pushing the 2 buttons and reset button on the back gives me the option 0 to reset but all I can see after that is a black screen which says USB at the top and at the bottom v1.00
What happened and is this the end of my PDA? Sync won t work anymore now since my PDA can t be detected by windows because I can t get in the PDA!!!
Is there something I can do??!!!
PLEASE HELP ME OUT!!!!
Edit/Delete Message
sounds like you're just in bootloader mode
I think you are in what's called bootloader mode. Read the wiki to check - the screen you are describing sounds normal to me you plug you device into the comp via usb (with sync over usb disabled in active sync) then install a new rom.
You really shouldn't have tried to flash your rom without reading some instructions first but I think that your device should be fine.
If you have already upgraded your rom just do a hard reset and select the option to reset.
Will this thread help?
http://forum.xda-developers.com/showthread.php?t=310056
I'm sorry, this is the thread I ment to link:
http://forum.xda-developers.com/showthread.php?t=310054
strangely enough I found out that I DID use a good version picked from this http://forum.xda-developers.com/showthread.php?t=298020 post. In this thread mwang gives a link to here http://buzzdev.net/index.php?option=com_phorum&Itemid=125&phorum_query=read,40,30486,30486#msg-30486 where I picked the dutch version. I than double clicked the MaUpgradeUt_noID.exe file and the software for upgrading started. When he was at 100% he said the the ROM update was completed and that I had to do a reset. So, I than pushed the three buttons (2x the - button and the reset button at the back of the 9000) but all I than see is the bootloader menu with USB and V1.00...........
Sorry for putting it in three sub forum, my fault, but the device is from my work so I don t want it to be screwed up!!!
sanderh said:
Sorry for putting it in three sub forum, my fault, but the device is from my work so I don t want it to be screwed up!!!
Click to expand...
Click to collapse
Rather late now, but if it's owned by your company for work, should you really be di**ing with it?
Solution to probl: Stuck in Bootloader
The one way of fixing your problems....you're officialy stuck in bootloader,
Here's the way to fix it:
1. Stop Activesync USB connection on your machine under connection settings.
2. Uni : Reboot Bootloader then Connect USB ( If your phone isn't in bootloader already..)
3. PC : Run mtty1.42.exe ( Download from XDA's ftp site or search the forums, I'm sure you'll find it.)
4. Choose USB in "Port" (Reconnect if can't find/reconglize USB and try remove sim and sd card)
5.1 Press Enter
5.2 USB> (This will show up)
6. Type: Set 14 0
7. Press Enter
8. Run your rom update again and it should flash this time.
did it start??
did it start?? ?
Hi. first post.
Have an o2 exec. Different brand same deice and none of the other methods worked but finally got it working. Using mtty1.42.exe it would not see usb connection and therefore could not go down that route.
I booted into the bootloader mode that says serial at the top and v1.00 at the bottom.
Connected to the pc and cant remember if i stopped wcescomm.exe or not but you can try both ways.
Then started Midget_1990_v1_0_PU10_WWE.exe rom and followed the instructions and voila.
Hope this helps someone.
"Using mtty1.42.exe it would not see usb connection"
You need to disable the usb connection of active sync under connection settings and then only mtty will pick up a usb connection..
Could anyone can help me to solve No GSM poblem. I think there are many other users have same problem.
After it faild during update rom, My HP6915 represent NO GSM during booting and the phone funcation also doesn't work. But in HP Asset you can see it, just no firmware, no version number. I try to flash english radio rom and french radio rom, but always stop at 1%. This matter appeared after I flashed orange rom(french version). I think it locked by Orange.
Does any one can help us?
did you try the update with no sim and no minsd?
EREZYAD said:
did you try the update with no sim and no minsd?
Click to expand...
Click to collapse
Yes, I update without sim card and minisd. Always stop at 1%
to be on the safe side i will go over general insraction
battery full
recomended xp os & activesync 4.5 (not beta)
minsd & sim out
ac addapter connected (ac power from orig transformer)
hart reset your device before the update
connect device directly to computer's usb plug
run the update
try radio only &/or the all update you can also try on a different pc
if all didn't work read this and see if you can find somthing that works on the 6900
http://www.htcwizardweb.net/node/170
good luck
EREZYAD said:
to be on the safe side i will go over general insraction
battery full
recomended xp os & activesync 4.5 (not beta)
minsd & sim out
ac addapter connected (ac power from orig transformer)
hart reset your device before the update
connect device directly to computer's usb plug
run the update
try radio only &/or the all update you can also try on a different pc
if all didn't work read this and see if you can find somthing that works on the 6900
http://www.htcwizardweb.net/node/170
good luck
Click to expand...
Click to collapse
Thank you for your reply!
I tried but still same, stop at 1% when I flash Radio WAN OS, stop at 2% when I flash Radio FS. I tried to unlock simlock and CID unlock, but it doesn't work on my 6965
called a few places looks like the radio chip is fried. sorry man...not looking good.
try update again with this method
I got almost same problem. I tried to update GSM rom but update fail and my ipaq stuck at hp invent logo. try following steps to see if it works for you
Solution:
this is what I did to get this fixed.
1) Get the battery out of the iPaq, and wait for a few minutes while the "serial" image fades away slowly.
2) In the meantime, prepare your cradle, plugged into the AC charger and plugged via USB to your PC.
3) After a few minutes, with the screen of the iPaq completely gray, put the battery and battery cap back on (with our without SIM card), and put it on the cradle immediately.
4) The iPaq should start coming back to life, as if it were being hard reset. Let is stay on the welcome screen (i.e., do not tap it or anything).
5) Restart the upgrade process, it should proceed from there OK
Thank you to origianl solution provider
I also meet such question.
actualy. I met the same problem "No GSM" after wrong update. I thing I tried everything, but I Didn't try to flash the device via mini-sd card. I don't know the right address for GSM area. Did anyone know?
caoxt said:
I also meet such question.
Click to expand...
Click to collapse
COME ON guys some one can help us , i have too the same problem please help with radio stack !!!!!!!!!
me too,, really nedd help here.. my only phone sable...
does anyone know of a company or repair service that will unbrick my hermes?
thanks
Whats wrong, maybe we can help...
Give us a brief rundown on whats wrong, and what you did to fix...
Well first of all,
the phone was bricked through unable to flash a rom
i didn't get a chance to check the SPL and IPL before the phone was bricked
the phone is only showing bootloader and the ok+power+soft reset doesn't work
ive tried the micro sd method and didn't work
i had just barely got the phone and was a noob at it so like every other person who doesn't take the time to read, didn't put the Hard SPL on the device.
i don't know what else to do now.
thanks for replying
Download the original SHIPPED rom.
Untick "allow usb connection" in activesync on your PC.
Reset into bootloader - hold power, OK button above flywheel and rset with stylus. This should bring you to thr tri-colour screen wher your IPL and SPL are shown. This is true bootloader, not a screwed up version. DO THIS...
Connect Hermes to pc.
Run RUU-Wrapper.exe of original rom.
This may or may not woirk, Good luck...
IF this works, go here - http://forum.xda-developers.com/showthread.php?t=296722
Download Hard SPL V7 & install it. Then you can use sd card method to flash roms, I find it safer...
Cheers...
ultramag69 said:
Download the original SHIPPED rom.
Untick "allow usb connection" in activesync on your PC.
Reset into bootloader - hold power, OK button above flywheel and rset with stylus. This should bring you to thr tri-colour screen wher your IPL and SPL are shown. This is true bootloader, not a screwed up version. DO THIS...
Connect Hermes to pc.
Run RUU-Wrapper.exe of original rom.
This may or may not woirk, Good luck...
IF this works, go here - http://forum.xda-developers.com/showthread.php?t=296722
Download Hard SPL V7 & install it. Then you can use sd card method to flash roms, I find it safer...
Cheers...
Click to expand...
Click to collapse
dude, thanks a lot!
last time my PPC was stuck at bootloading ( I guess my Hermes 100 can't support M2d due to lack of RAM ). Then I do the step as u mention, n it work!
Thank God. I'm feel relief now, knowing my PPC is revive.
ultramag69 said:
Download the original SHIPPED rom.
Untick "allow usb connection" in activesync on your PC.
Reset into bootloader - hold power, OK button above flywheel and rset with stylus. This should bring you to thr tri-colour screen wher your IPL and SPL are shown. This is true bootloader, not a screwed up version. DO THIS...
Connect Hermes to pc.
Run RUU-Wrapper.exe of original rom.
This may or may not woirk, Good luck...
IF this works, go here - http://forum.xda-developers.com/showthread.php?t=296722
Download Hard SPL V7 & install it. Then you can use sd card method to flash roms, I find it safer...
Cheers...
Click to expand...
Click to collapse
See the problem that i have with that is the fact that i don't know what my original rom was, all i know was that it was an htc windows mobile 5 rom, but i don't know what version..
could it help if i told you that it is a qtek 9600 (herm100)?
Owh, forgot to mention.
I already applied hardSPL. I guess thats why the process of recovering it quite simple. N I directly flash the ROM to WM6.1 v13.3 Cooked Rom. It works like a charm.
Bo0mcxh402 : sorry mate. I didn't know the original version of ur ROM. Maybe u can try to ask around. I'm sure there've lot of users out there also using the same phone as yours,
Try the HTC stock WM06 rom which you should be able to find somewhere on here... May work...
Cheers...
Bo0mcxh402 said:
See the problem that i have with that is the fact that i don't know what my original rom was, all i know was that it was an htc windows mobile 5 rom, but i don't know what version..
could it help if i told you that it is a qtek 9600 (herm100)?
Click to expand...
Click to collapse
It's irrelevant what your original ROM was/is. Follow these directions and use the T-Mobile ROM.
The T-Mobile ROM won't install. It will go thru a couple of steps (one of which is "Erasing" which is critical to get through) and then it will "Error" out. After the T-Mobile ROM "erases", your Hermes should be back to a state where you can flash any ROM you prefer.
Timtown said:
It's irrelevant what your original ROM was/is. Follow these directions and use the T-Mobile ROM.
The T-Mobile ROM won't install. It will go thru a couple of steps (one of which is "Erasing" which is critical to get through) and then it will "Error" out. After the T-Mobile ROM "erases", your Hermes should be back to a state where you can flash any ROM you prefer.
Click to expand...
Click to collapse
Well i Tried the method, but i can't even get the phone to sync even after i unticked the "Allowed USB connections," the phone is recognized as "HTC usb connection" but when i run the t-mobile rom, it says error 264, (USB Connection)
The reason I said to use the shipped rom is because Bo0mcxh402's device ISN'T supercid... If it was it could take ANY rom you want to throw at it BUT because its not you HAVE to have the STOCK CARRIER ROM it was shipped with (later update may work too as the cid should be recognised)...
Cheers...
Bo0mcxh402 said:
Well i Tried the method, but i can't even get the phone to sync even after i unticked the "Allowed USB connections," the phone is recognized as "HTC usb connection" but when i run the t-mobile rom, it says error 264, (USB Connection)
Click to expand...
Click to collapse
Did the T-Mobile ROM do *anything* or just immediately error out?
Timtown said:
Did the T-Mobile ROM do *anything* or just immediately error out?
Click to expand...
Click to collapse
I couldn't do anything because the t-mobile rom didn't recognize my hermes even though my computer did
That pesky CID again as stated so many times before. You need to find your stock carrier rom. The upgrade to WM06 will work as well as it has the same CID as the shipped rom.
ultramag69 said:
That pesky CID again as stated so many times before. You need to find your stock carrier rom. The upgrade to WM06 will work as well as it has the same CID as the shipped rom.
Click to expand...
Click to collapse
well i ended up trying that and nothing happened... the usb connection didn't work for the hermes, i know that there is nothing wrong with the usb connection because i used it on my t-mobile dash.
IVE GIVEN UP.. IS THERE A COMPANY FOR A REASONABLE PRICE THAT WILL UNBRICK THE PHONE?
On the PC - Untick "Allow usb connections" in activesync settings.
On Hermes - Hold OK button, power button and reset with stylus. This will bring you back to bootloader BUT it won't be the screwy bad flash bootloader.
Connect the Hermes to the PC via usb. Run the RUU_Wrapper.exe of the stock rom.
This should work, if it doesn't then there may be no help available. You don't want activesync trying to connect to the Hermes so its better to disable the usb connection settings, You might be able to get a successful flash this way without activesync screwing it up.
Can't say about any unbrick service. Don't think they could help, only thing they might do is replace the mainboard (if they can find) and that would be expensive.
Cheers...
Hi all.
I just a got a HD2 today. And the first thing that came in my mind was "Let's go to xdaDev to get a nice custom rom". I downloaded one.
After that I put the usb and try to make it syncronize. And the problem is here : ActiveSync dont reconize the phone. I spent the last 4 hours to google why it shall not work. I tried to unstick option at "Start=>Settings=> Usb to PC" but it dont work. Nothing more after perfoming a hard reset and reinstall ActivSync.
But something is strange : When I go in the bootloader, there is the 3 color screen and the phone Display "Serial" at the bottom of the screen ; and when I start it again with USB plugged, it doesnt display "USB" instead of "Serial" it's just void and if I remove the USB "Serial" is displayed.
Plz help me to make the phone syncronize .
I use Windows XP (no firewall, no antivirus) and an official Orange Rom. My SPL is 1.42.0000. I just hope there is no hardware problem ...
Some news ...
The HD2 isnt detected on 2 other PC (Both Win XP). I managed to syncronize my old Diamond too, and it worked well. Same with a HTC Touch and a Touch Cruise, the 3 ones works.
I also tried to use Bluetooth to get an Activesync connection and this time, it noticed the HD2 but no way to get a synchronization.
Any ideas ?
Try this: goto Settings, Other (Miscellaneous settings), USB to PC, Enable faster data data synchronization. Try to tick and untick the last setting.
It doesnt work . I'm trying to follow a "GoldCard" tutorial to flash to an official HTC rom. Maybe it's Orange operator rom ... But if you have any other suggestion, let me know
I can't believe that it's such a s*** to just connect the last HTC phone to a computer. The tutorial need ActiveSync to get the SD card ID so I will not succes in this way.
Is there another software that can be used instead of ActiveSync ?
Did you flash any rom at all or are you still stock?
If you have flashed already, Have you tried to go back to the default shipped rom using sd card (not goldcard)?
Find the rom that shipped with your device, extract the RUU_Signed.nbh file from it, copy it to your fat32 formatted sd card, rename leoimg.nbh, put card in phone, boot phone with down volume held, hopefully you get the message on the three colour screen saying something like 'press volume up to start' or somesuch.
THis should not only flash the rom, but also fix spl if it has become corruptted(which appart from hardware errors is the only reason i can see that it wouldn't recognise a USB connection)
Make sure it is the correct rom for your phone, though, correct vendor and region id.
I must say if you havent flashed yet it sounds like a hardware fault with teh usb cable/connector
I'm currently running a stock Rom from a french operator nammed "Orange". I haven't flashed anything since ActiveSync just dont want to know anything about my HD2.
Maybe I shall send it back to the seller. That's so frustating ...
If i dont find a way to solve this problem until the end of the day, I will return the phone.
Anyway thx for trying to help me
To me either the cable or the phone is faulty. Try another cable if you have one, if not just have the phone exchanged.
Phoque_You said:
I'm currently running a stock Rom from a french operator nammed "Orange". I haven't flashed anything since ActiveSync just dont want to know anything about my HD2.
Maybe I shall send it back to the seller. That's so frustating ...
If i dont find a way to solve this problem until the end of the day, I will return the phone.
Anyway thx for trying to help me
Click to expand...
Click to collapse
Ah in that case then i'd seriously consider taking it back /sending it back. Especially if you have tried more than one computer, sounds to me like faulty cable or USB socket.
kilrah said:
To me either the cable or the phone is faulty. Try another cable if you have one, if not just have the phone exchanged.
Click to expand...
Click to collapse
You must be right. I tried everything and I never had so much pain with my others HTC to get syncronization
I had the same problem not beeing able to connect to the internet via computer. After playing with the activesync settings on the Computer -> conection settings-> ticking on and off some of the boxes->ok, it worked again.
I have connected to three of these phones ( 2 french 1 english) and no problem whatsoever, everything happens without needing to touch any of the settings...is your pc even recognising that something is being plugged in on the USB?
Have you installed the latest version of activesync?
If you have done all the obvious things and it still does not work, the phone or the cable is defective...It should connect straight out of the box with a standard, un changed version of activesync.
Send it back!