i-Mate JamIN Q200 G3 (PM300) - JAMin, XDA Neo, S200 General

Ok got my phone doing some funky stuff...
Before I turned off the phone, the phone was default, with extra programs that is all. Basically i was doing my thing, then the phone kept trying to record a new sound file, in the notes section.
I turned off the phone and back on, now the phone starts in the bootloader, 3 color screen.
I can successfully patch ROM files to the phone, but I can't get past the bootloader. I have pulled all the casing off the phone, just to see if anything was holding the buttons in, but no such luck either.
IPL 2.20
SPL 2.20
Loaded on some of your rom's cause it's about time i did this.
I can hold the camera key, and get to the reset factory default, but when i press the green key nothing happens. Anyone got any idea's what is going on

fixed with a hard reset

how to hard reset this model ?

com button, power on +camera ;keep them

how to do this ??? and what - where is the Com button
how to do this ??? and what - where is the Com button ?
what is ???
please reply to this email [email protected]

Related

new rom made my jasjar a brick :(

I used the new rom from i-mate JASJAR_WWE_13076_164_10900_wwe_ship, it gave me an error message error 116, i followed instructions to recover, no use, i cannot even hard reset any more (it gives me the white screen, and when i press 0, it just goes back to be switched off).
I am going to put back the previous rom if it works...
anyone had this problem? any suggestion how to solve it?
help much appreciated
Nabil
Can u put back on bootloader menu?
In my upgrade it did the same, but it could go to bootlader... then i tryed to flash it again and it worked ok.
bootloader how?
I only get a white screen when i hard resest with x and 0 option...
how do i get to bootloader?
help much appreciated
Reset (stylus) + Power + Light
A thing like that
Bootloader mode: Hold light and power buttons together and reset with stilus.
i get the usb bootloader message
thanx for the tip...
i get the message on the device upgrading the radio stack, so i have access to the bootlaoder, then i get an error message on the pc side...
so i made progress, but still not working to completion
started working at third attempt
hope it works thanx a million dude u really rock!
steps
Since this helped me, I will write the procedure again here:
You need to have access to the bootloader.
Connect the jasjar to pc usb
Access bootloader
To do that u press together the power button and the light button (light button is 3rd button in the front) and reset button (with stylus), u might need to put stylus in mouth to do that as it is a bit fiddly.
The screen will be dark but if u use flash light on it u can see usb written on the screen
Then start the upgrade from PC, u might need to try all of this a few times, it took me three attempts to get the upgrade started
You will also be able to see the message upgrade in progress on the jasjar screen which will be still dark.
Nabil out
Glad that your universal is up.
:lol:

White Screen only

I just installed this program, used default settings, apllied, My 8125 soft reset.
Now I cannot see anthing past the initial screen that lists IPL and SPL version.
Just a plain white screen, Active sync wont work, no buttons work. Please help !!!!!!!!!!
If you're stuck I think the only next step would be a hard reset which is going to drop it back to the base factory build so you'll lose anything you've installed etc.
How do I hard reset 8125, with buttons only (key / button combination) OS does not boot or visible.
press the "connetions" button (on the left hand side of the unit next to volume up/down) with the "voice" button (right hand side of the unit opposite the connections button) and then use the stylus to do the normal soft reset and it should hard reset back to factory settings - it's described in the manual
Tried hard reset several times, no luck.
All I did was installed registry wizard from here
http://forum.xda-developers.com/viewtopic.php?t=39725&highlight=registrywizard
and now I can't get it to do anything, anymore suggestions ?, your help is really appriciated, I have only had the phone to 2 days and its dead already
try holding the same two buttons and then hitting the power button instead of the reset thingy... this method was easier for me... If this dosen't work you will have to enter bootloader mode and reflash the rom.
For the detailed reset procedures try here
By the way, did you use that program to change the default input method?? I use it all the time and the only time it gave me the whitescreen is when I tried to change the default input...Oops. I believe that you should be able to use that program safely, just leave the default input alone... Hope this helps.
Thanks for info, I did manage to reload the ROM. and Yes I did change the default input method, that might have done it. Thanks all, for your Help.
raheelb did you have the warning that the proggie cannot recognize the AKU version?
I had had such a warning, unfortunately bypassed it and had the same issue (white screen) - any one knows why the RegistryWizard cannot recognize AKU version? I have the original Qtek 2.17 ROM installed... :?

my k-jam hangs

Hi,
Recently my pda(k-jam) fell from my pocket and it hanged. I did a soft reset but I get this error message "Press Send to restore factory defaults, Other keys to quit"
I tried all keys but in vain. I then did a hard reset by pressing the comm and the voice dial. (did a reset with my stylus). I still get the above error message.
Does anyone have any suggestion or idea how to reset my pda?
Thanks alot.....
Y dnt u flash it with a new Rom look around the forum for the new MOSKI ROM.
Thanks
Thank you for your suggestion, I will think of upgrading to molski.
But will it upgrade ? As a hard reset also doesnt seem to work and how do I get to reach the ROM if I am not able to see the other things?
Thanks
Please help...
Hi ,
I am a newbie and so would seek alot of help. Thanks in advance...
Couple of days back my pda fell and now after soft or hard reset the screen still shows this "press send to restore to factory defaults, other keys to quit"
I would like to upgrade to molski but they say I might have to downgrade my rom but I must first unlock the device. There are g3 or g4 device..how do I know what device my k-jam is...g3 or g4? How do I follow up or know?
Could anybody give me the link or solve my problem? As my k-jam just wont pass that screen..I tried looking into various topics but couldnt go about the first step I should be taking...
Please help!
Thanks
Hi,
Please help..after hard reset, it still does not happen to load into the factory defaults... I cant flash my ROM or anything ...as it wont progress further than that screen ... "Press Send to load factory defaults, or quit"
Anyone have any suggestion?
Hold down the camera button while resetting it. If you can get it to the bootloader (three color screen), you might be able to flash it with something and possibly rescue it. It does, however, sound like you might be screwed. Things break when you drop them, including plastic phones.
hi
Thanks but if I have to do a hard reset, I would already be holding the comm manager and the voice dial with the stylus to reset. Do I hold all the 3 buttons together while hard resetting ?
I have tried all the buttons after doing the hard reset but just doesnt get to the other screen.
Thanks for your help.
Hold down the camera button, Power Button and Pin in the hole. First relese the hole, then release the power button and keep holding the Camera button dis will bring the Tri-colour screen. There'll be some info. like IPL n SPL der
If IPL n SPL are like:
IPL 2.xx.xxxx or 1.xx.xxxx
SPL 2.xx.xxx or 1.xx.xxxx then ur device is G4.
if its like:
IPL 2.xx or 1.xx
SPL 2.xx or 1.xx then ur device is G3
if its G4 you need to CID Unlock that before upgrading it.
All the LUCK. Go Ahead.
Hi
Thanks,
I tried your steps but it still wouldnt work. But somehow I did the switch below the comm button and it showed me the screen to the somethign HTC innovation or like that.
I think I had to tinker with the switch below the button to get the screen working.Thanks for your help.

T-Mobile MDA USA weird, "fixies" dont work, stuck in "press send to restore"

T-Mobile MDA USA weird, "fixies" dont work, stuck in "press send to restore"
Hi, sorry for my poor English is not my first language
I have a T-Mobile MDA USA and happened a weird thing, my phone works properly, was CID unloked and sim unloked with TNT_5.0_Wizard_TouchFLO ROM but 3 days ago I put the USB (PC)to charge the battery, lately when I back to pickup my phone I see in the screen of the phone open and close or put an quit windows explorer(mobil) repetitively, i try to close manually tapping in the "X" but explorer continues opening, then I see in the bar where you put the web address the number "3" and "8" was typing continuously, like when you hold pressing the buttons, but nothing was pressing or making pressure to do that, since I cant close the explorer with the "X" I turn off the phone, when I turn on instead to load normally, appears the Align Screen and for some reason will not recognize the Screen Tapping to align the screen, so, I turn off/on again, but in this time shows a black screen with "Press Send to Restore Factory Defaults, Other Key to Quit" in withe letters, it is stuck in there since, before to put this tread I have read this forum and still I am lost, because i do a Soft Reset or Hard Reset #1,#2,#3, I enter into a bootloader mode to re-flash the ROM with CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE ... IPL/SPL 1.01 and when finish to flash, its suppose the phone restart and windows loading but instead that I get again the same black screen with "Press Send to Restore Factory Defaults, Other Key to Quit" in withe letters, ok, maybe with other recently ROM, then I enter into a bootloader mode to re-flash the ROM... AGAIN... but now with ruu_prodigy_226102_22610105_022511_tmous_wwe_ship... IPL/SPL 2.26 ... and AGAIN I get the same black screen with "Press Send to Restore"... I try to press send key always, but nothing happens, is still stuck there always, I could not get past that, I would really appreciate any help. Thank you so much.
I hate to ask this, at the risk of sounding too obvious, but are you sure that it was CID unlocked properly? I have a Cingular 8125 with IPL/SPL 2.25 and I know it was a hell of an effort to get it CID unlocked, five or six tries before it worked properly and I was able to flash successfully.
l33tphreak said:
I hate to ask this, at the risk of sounding too obvious, but are you sure that it was CID unlocked properly? I have a Cingular 8125 with IPL/SPL 2.25 and I know it was a hell of an effort to get it CID unlocked, five or six tries before it worked properly and I was able to flash successfully.
Click to expand...
Click to collapse
yes was CID unlocked properly, I do it with lokiwiz02b like 3 moths ago and I use Wizard Service Tool to see was really unlocked, I could flash any ROM since was unlocked I could use crosbow,faria, Molski even TNT.20273_Professional ROM's but I prefer use TNT_5.0_Wizard_TouchFLO because I feel my phone works more stable and speedy... searching in treads I see Im not the only one with the same problem (stuck in a black screen with the legend " Press Send to restore factory default, other keys to quit" in white letters) but in that treads no one get answer how fix this problem or how get out of the black screen.
like I say before I could put my phone in bootloader mode and re.flash the ROM wherever I want to try running ROMUpdateUtility and always I reach 100% then, when its suppose the phone restart and you will see the windows logo or T-mobile, don't happen that, instead I see the famous black screen with white legend, so the legend says me "press send"... I press send, or any key and nothing happens... I read in other treads when you press send the phone formating but this is not the case, just don't do nothing,.... realy I need some help here
thanks
Hey!
I have the same problem as described above. I've been using CR96 Touch HD WM 6.1 with soft SPL unlock for couple of months with no problems until tonight when I noticed that my phone is hanged. I did a soft reset, but the phone gets stucked at "press send to restore factory default, other keys to quit" screen. At that none of the buttons work, soft resetting just puts it back to this screen, the same goes for taking the battery out. There have been no software or registry changes within weeks - just using basic phone functions. Is there any way how to fix this or what could be the problem?
Thanks in advance

HTC break down! Help!

My HTC do not swich on. Today my battery dischargerd, when I pluged in power it did not swich on. It shows only red green blue white stripes. help!!!
Im sorry for may bad english
When I conect to my PC if finds some device and on HTC on white stripe is written USB
It's your SPL screen. Try this:
push the internet and message buttons together and reset your phone. It asks for reset, press the green phonekey. This hard-resets your device.
It does not help
Did you flash any ROM yesterday night ???
No
Only my HTC batterry full discharged.
Very strange, i don't know if is the case to use Mtty, wait for others opinions.
NeoS2007 said:
It's your SPL screen. Try this:
push the internet and message buttons together and reset your phone. It asks for reset, press the green phonekey. This hard-resets your device.
Click to expand...
Click to collapse
Neo's syggestion is correct maybe you did i wrong? if you do it correctly you will have a message saying
this operation will elete all of your personal data and reset all settings ro manufacturer default. press send to restore manufacturer default, or press other keys to cancel
the press green phone icon
if that fails download and flash the correct ROM for your phone i.e mine is avalible from o2 in english

Categories

Resources