hello
please help i have a mda compact a cannot get the phone to wrk any more no service.
rom flashed
hard reset
does not go into factory reset (2 side buttons plus reset holding on to 2 side buttons) please advice this site is awsome
mda compact is a "magician", you may already bricked your phone by flashing a 'wizard' ROM into it.
it is not bricked. it does search and then stops
Hardreset it
Start -> Settings -> System -> Clear Storage
heelp
my friend there is no such route . yes the wizard format is like that,i have hard reset it (when it ons annd goes to the auto custamisation bit
rom ver 1.13.00 wwe
radio ver 1.13.00
protocol ver 137.43
no sevice
turn on flight mode
i switch it on and off (originally was not able)_
get antenna sign with !
You are very confusing. At the very first post, you just mentioned that it "does not go into factory reset". You need to provide more information, example (not limited to) the ROM that you've flashed, the ROM source, method of flashing the ROM, etc etc etc. There is a limit of patience how many rounds of 'suggest-answer' session I can go through. Try to give as much info as you can. For example, you have not even confirmed with me if your phone is a Magician or a Wizard.
From what it seems, your ROM is way too old. Mine is 2.xx.xx version. So, yours is old. Flash a new *official* ROM and try again.
thank you
i thank you what i had was a magician with no service and a wizard with a damaged screen, what i did was swop the screens and unlocked the wizard with locwiz 3 to use my o2 chip now the wizard is fine. but i am in the process of fixing the magician.
i thank u for u'r time
Related
Dear all
i just have regitered over here after i tried alot with shop's over here to change the language of my T mobile MDA from GER to ENG
i searched all the forum to find out where i can get ENG ROM and the correct way to falsh it with USB cable ... am not expert to flash it in bootloader mode
Can any one help me please out here ?
Thanks in advance for all
http://lumpistefan.dyndns.org/ - all versions, languages + couple of nice progs that can be optionally included straight in ROM - make your RAM free! :lol:
Thanks alot bob190cm but am looking for the orginal latest version for my PDA
Thanks man for your effort
tmobile's uk site would prob be a good place to start looking
2 sunpower:
Actually, if you unmark "Add software and modify ROM" option, you get the original ROM - 4.01.16 ENG is the official T-Mobile release of WM2003...
Man i downloaded the 2003 ROM and tries to upgrade my PDA but it killed it ... ActviSyn does not recognize it any more
what do i have to do now do i have to try the bootloader way ?
if yes what do i need to do it and how ?
Have a look around that forum.
Now I can tell you this: activesync will not recognize it - simply try running the update again. If doesn't help - see forum for exact instructions how to run the SD update.
PS: what actually happened?
I made a 2003 rom for my XDA I T mobile device i tried to upgraded it but it hangs up and a mseege appared asking me to soft rest my device and try the operation again ... now ActiveSyn not connecting to the device and i dont have an SD my Bootloader is 5.25 is this loader is bad ?
Please advice.
Thanks
i forgot to ask you what is soft reset and hard reset ?
sunpower said:
i forgot to ask you what is soft reset and hard reset ?
Click to expand...
Click to collapse
A softreset is a restart of your device. You do it by putting your stick in the little hole down on the left side.
A hardreset performs a blank installation of the System stored in your Rom. All applications an data installed will be lost. You can do this by unsrewing your stick, putting the top in the little hole down on the right side, wait for about 60 sek. and do this again....
HTH
Stefan
You guys are wonderfull :lol: i got my XDA back by bootloader method .....
The problem appeared today morning, while listening music using tcmp. the sound stopped suddenly, and standard animated cursor appeared over tcmp screen. i closed tcmp, and the rest of the system seemed fine, i was able to mute the phone and entered my work place. After a while i noticed the screen is off and i can not turn it on using pwr button, although green led kept blinking so the phone was operating. after a soft reset it would not go over splash screen showing IPL, SPL (which are: IPL: 1.06, SPL 1.06, GSM: 01.12.10, OS 1.6.2.4).
I've tried multiple times and still the same, only difference is that sometimes I can see the cursor and sometimes not. I can get to rgb screen and "press send to restore" as well, but that's it. I can't remember whether previously pressing a key illuminated a screen and keys, but now it doesn't. I used to have problems with screen not going black on idle since few days, but that's it. What could have happened? And if the only solution is hard reset, please tell me, could I somehow backup my contacts now? I don't have activesync here so I have to wait till I finish my work to find out..
please help anyone...
rom version : 1.6.2.4 WWE,
date : 11/15/05
radio : 01.12.10
protocol : 4.0.13.23
extrom : 1.6.2.105
That's spooky. My MDA has the same versions of IPL, SPL, GSM and OS, and this morning started misbehaving.
What's this rgb screen you can get to with the "press send to restore" option?
How do I do a hard reset (I have a backup on SD) without being able to get to the Start>Settings>System>Clear storage control panel option?
Rgb screen is a bootloader which i enter by holding cam+voicedial+commmanager butons while softreseting wizard. the other screen i mentioned i enter holding cam and voice buttons, and then pres reset. that screen says 'pres send to restore factory defaults any other key to quit' and it does hard reset if you press green button here...
my problem seems to be over for now, i managed to turn the phone on while i plugged it into a wall charger (believe me, the battery was not a problem - i don't know for how long it's ok now, but at least i made contacts backup now so that i'm ok with a hard reste if i have to...
You both have old roms and could do with upgrading them to aku2 roms. (your device will be more stable) i.e. the first number of the rom will be 2. Please dont ask me to go through how to flash a rom because there are hundreds of posts on the same topic and read the wiki - shortcut top left of the screen. You need to identify whether your device is g3 or g4 but i suspect you both have g3 chips.
Now read & read esp the wizard upgrading forum and wiki and then when you feel confident - flash your device.
mu chipset is g3 based on my ipl/spl info... i wouldn't dare to ask anyone to explain the process of flashing, i'm not that crazy. only thing i'd dare, would be to advice me what rom should i use... or a way to determine this, since i know it can't be just any rom...
banannq said:
mu chipset is g3 based on my ipl/spl info... i wouldn't dare to ask anyone to explain the process of flashing, i'm not that crazy. only thing i'd dare, would be to advice me what rom should i use... or a way to determine this, since i know it can't be just any rom...
Click to expand...
Click to collapse
Looking at your rom numbers i gather you have a t-mobile vario - is it uk or usa rom or polish - i see you live in poland.
there latest uk rom is here ftp://[email protected]/Wi...Prodigy_2210206_109_21911_TMO_UK_WWE_Ship.exe
us rom ftp://[email protected]/Wizard/Roms/Tmobile/RUU_Prodigy_2170702_217_20710_TMO_US.exe
user name xda password xda
Its prob best you sim unlock and cid unlock before you flash in case you change to a non-tmobile rom inc one of the cooked roms.
see here http://forum.xda-developers.com/showthread.php?t=249474
and read dr puttingham's tutorial http://forum.xda-developers.com/showthread.php?t=285435
and now i have given you more than enough hints
p.s. by the way remember to write down your gprs settings and mms settings to use with your new rom.
thats right, its tmobile vario, uk one. it is sim unlocked, i'm not sure about cid but it should not be a problem. thanks for the hints, it really seems more then enough;] i'll probably have to use theese, as soon i have a spare evening...
you don't have to explain me the importance of gprs settings - forcing my wiz to work in uk's o2, then in polish plusgsm, then loosing settings and doing it again finally got me into a habbit of backing every settings up ;]
and last but not least, guys, yesterday i did my first HR ;] ...
hello all,
i'm a newscommer on this forum,i've trust in upgrade my phone with aku3
i correctly followed the topic , install step 1 (forG3) and step 2
my device worked fine after the first install (qteck 2.15 fr ->2.2 from step1)
i've synchronize my phone, and run the second part, installing without problems, reboot > freeze on the boot screen htc
no way to synchronize again. my phone is reconized by mtty (1.51 and 1.50) but i don't know how to use it
ipl 2.09
spl 2.20.0000
gsm 02.47.21
os 3.0.0.0
i've tried all the night to find a solution on all forum i knew, i drive me to this one, i think it could help me best ( you'r pro dudes )
but i'm allways stick. i've call htc division hotline (i'm from france) , they said i have to send back my phone ( but he's now out of waranty, cause it's not a legal rom i've installed, so i have to paid, and i've allready too much invest on my device)
plz said me there is still a hope!
did try upload another rom from bootloader ?
did try upload another rom from bootloader ?
but first try a hard-reset
i don't know how to load a rom from bootloader (i allready have made soft and hard reset
no one could help me ?
1. dowenload this latest Qtek official rom from here: ftp://xda:[email protected]_220734_2207114_024721_QtekWWE_Ship.exe
2. enter your S200 into bootloader mode by pressing power +camera + reset, let go of the reset, but keep holding power + camera until the three colur screen will show up (that is bootloader mode).
3. connect the S200 to your pc (make sure your battery is fully charged)
4. run the Qtek official rom.
5. good luck!
i've tried those kind of upgrade several time, but without possibility of establishing an active sync connexion, it's impossible to launch the rom install...
does samebody knew if it's possible to make a rom dump with an emulator and copy it on a sd card for autoinstall backup in bootloader mode ?
while in bootloader you don't need to establish any activesync connection. just plug the usb cable, then if appears "usb" on phone you are good to go.
install the original DOPOD rom from the ftp.
this rom don't work, it give me the message
error 294 invalid vendor id
it's now working ! great !
i've juste install again the step one of jester's aku3.3 (so, i'm on a 2.20 os, i think i'll keep it for a while )
thank you verry much
pti_nourson said:
it's now working ! great !
i've juste install again the step one of jester's aku3.3 (so, i'm on a 2.20 os, i think i'll keep it for a while )
thank you verry much
Click to expand...
Click to collapse
So you can now change your signature again, right
please help! I have made a wrong ROM Update for my Artemis. The result is that it doeasn`t starts anymore. I see only the start screen no more. If i make a SW or HW reset tahn i see a 3 colored screen and USB. But i don`t get a connection via usb to my compute`! How can i wake up my Artemis ???
tell use more what did you do and how did you do it?
what artemis is it?
what rom was it
Flash went sour..
You need the original ROM which was on your device when you bought it. What version (HTC, MDA, etc..) and what language was the original ROM?
please i need help too
I guess I made the same or a similar mistake that dr.moppi did. My machine is a Dopod P800 from mainland china with the chinese operating system. I flahsed it with PDAMobiz_Dopod_P800W_AKU301_v1.1.2_PowerMap. Don't really remember what the original ROM was but now when i turn it on it freezes when it lights up. On the screen, it says
IPL 1.27.0001
SPL 1.27.0000
GSM 02.67.90
OS 1.28.0.0
DOPOD
I don't get a connection through usb to the computer either. I am not sure if I did the hard reset correctly. Didn't understand the instruction on that "press the soft key left and right and soft reset at the same time." Anyway, you guys are all experts, can you help me please?
it should be the same as my problem
if i remeber than i used the same ROM Update :-(
I hope anyone could give us a solution, please.
@dr. moppi we can only help you if we know what version you had before.
@empathyvirus you have to look for the original ROM which, in your case, should be the Chinese Dopod ROM. Install that one and your good to go.
Without the original ROM the only thing left to do is: sending your device to your provider or contact and sent it to the guys of imei-check. Either way, you'll probably have to pay to get it fixed.
how to install original rom
Thanks for your quick reply Pyth. In the case I get the original ROM from somewhere, how do I install it if I can't get a connection between the phone and my computer? Can you advice?
Put your device in bootloader by pressing the record button and reset at the same time. If you have your USB-cable connected between your PC and your phone it will indicate a connection by 'USB' in the left corner of your device. Now you should be able to run the ROM executable and update your device.
thanks anyway
i tried but it didn't seem to work. anyway, i have troubled you enough and maybe it's best i just go to the repair centre of dopod and pay for a fix. i really appreciate your help though Pyth.
Where can i find the t-mobile rom its the MDA Compact III that wont start for me
OK heres my situation:
i upgraded from the stock o2 wm2003 to wm6 using the wiki ROM:
Helmi Windows Mobile 6 Profesional R0
CE OS 5.2.1620 (Build 18125.0.4.2)
now on bootup it says
R:none
G:none
D:5.60.00 WE
It boots up fine but....
i cant get any reception.- just says "no service"
i have also tried disabling and re-enabling "Phone" in com manager
Yes, i have done a soft reset, hard reset and ive tried XPLODE wm6.5 and my current wm6 ROM.
XDA unlock all reported a successful unlock.
HELP!!!
OK, i did the thing in the ROM post said:
"R None if you take out battery and turn it on without push the reset button twice.
SDK?"
and it works now but when i turn it on i have to press the reset button twice every time
can someone help?
first of all you must unlock sim under WM 2003, then remove the extrom of 2003 to gain adidional 16 mb of storage (resize DOC), then you must upgrade to radio version 1.15 and then you must try any WM5, 6, 6.1, 6.5 rom
so now flash your shipped rom, you may find preferred rom for your operator in my signature, then start everything from the beginning
ok, it has kinda settled down now, working as normal.
I have "unlock sim under WM 2003, then remove the extrom of 2003 to gain adidional 16 mb of storage (resize DOC)"
If i wanted to upgrade my radio version would i have to flash the ROM again?
no you can flash radio rom only without the OS
Jejeje
Hey Xplode i never was able to see that tools like unlock extrom and repart DOC works on my BA... it always shows an error! when i execute the unhide hide repart etc etc.. so I upgrade even tought jajaja.
they only work on WM 2003
xplode said:
they only work on WM 2003
Click to expand...
Click to collapse
are you sure xplode, cause i unlock my phone using the tools from the BA wiki and im using wm6.5.
ok,
i upgraded my radio to 1.15.....
but i still got the problem
none
I get this on my wm6.1 but normally gets sorted after a soft reset
HMM!!!!
Same problem, after updating from stock WM2003 to WM6.1PRO all steps done like the wiki steps except the ExtRom step, couldnt get the unhide, unlock program to run (missing file or libraries error), so i flashed sun's WM6.1PRO without the extra storage, now when i change the battery i get the NO radio bootloader, still im able to fix it by doing a soft reset, but the strangest thing is that im not able to use the wifi :/. So the thing is, when i turn on without the radio i can use the wifi, but no the phone(airplane mode), and when i do a soft reset, the radio shows and i can use the phone but the wifi doesnt turn on at all!. Any help please, dont make me choose betwen my phone and my wifi
PD: is not only the radio missing the i change the battery, also R:none G:none
I have a Qtek9090
very odd ,i can use my wifi when the phone is on.
But i went from wm2003 to wm6.5 to wm6
wierd....
so, is there a solution? I've got the same problem
Ops! Solved. Do a soft reset via the button.
(I always do a softreset via unlocking the battery and locking it again)
Every one here should know that there is no WM 6 for BlueAngel by microsoft. it is ported on BA by helmi_c and that >> R none and G none << Bug is in WM 6 from very first day. SO Whenever u pull the battery out u need to SOFT Reset the device after putting the battery on phone.(u need to wait to start the phone to reset, just put the battery and insert the stylus at reset point.)
there is no point discussing about this anymore. thread should be closed.
i have the solution about this problem, im recovery from it.
first of all, downgrade ur ba tu ship rom, and go back to upgrade 6,5 rom, after finis doit "WM5" hardreset.... search the way in wiki.
wala........its done and run normal r;none g;none not see again. have try it
This is an old problem... Rnone Gnone
solved by sticking your soft reset button after changing battery or a hard reset.
The Wifi-Phone problem is solved by buying a new battery. The Wifi module wont fireup because of the lack in power draw since the phone is using much of it.
Buying a new battery solves plenty of problem. even OS speedup because it solves the lag the "modules" (e.g camera/lan/phone/mmc) detection gives while in bootup or execution.
If you still have problems. We can always point to the wiki.
Have a nice day!
-SS-