i have SPV M3100 with
when enter boot HERM100
IPL-1.01
HERM100
SPL-2.03
when power M05
S04 NO gsm
B06 D3.60
after powered with splash imaging Orange phone hang on white screen
i tryed with some rom from forum failed error with INVALID VENDER ID or UPDATE error
(alway error at 1 or 7%)
i think my phone is locked SuperCID
anyone can help me???
thank in advance
Hard-SPL
mrphuc said:
i have SPV M3100 with
when enter boot HERM100
IPL-1.01
HERM100
SPL-2.03
when power M05
S04 NO gsm
B06 D3.60
after powered with splash imaging Orange phone hang on white screen
i tryed with some rom from forum failed error with INVALID VENDER ID or UPDATE error
(alway error at 1 or 7%)
i think my phone is locked SuperCID
anyone can help me???
thank in advance
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=296722
To try and recover - RE-INSTALL THE STOCK, CARRIER ROM. Then HARD SPL YOUR PHONE!!!!!
Your phone ISN'T supercid by default. Hard SPL is the best way of doing this. I can't guarantee you will fix this problem as there are a hell of a lot of others with this problem. Do a search with the words "SPL 2.03 brick flashing" and you'll see, might be able to help too.
Good Luck...
I Had Found Provider
This Is From Orange Romania
I Tryed With Spl Not Done
How To Find Original Rom From Orange Romania????
See if they have a website. It may be WM05 though. Thats OK because you can then install Hard SPl and reflash afterwards. If you can't find........
nothing found!!!!!!!!!!!!!
ultramag69 said:
See if they have a website. It may be WM05 though. Thats OK because you can then install Hard SPl and reflash afterwards. If you can't find........
Click to expand...
Click to collapse
nothing in they's site
what i must to do?????
Hey people,
I have got on nice MDA with ipl and spl 2.21.0001
me problem is i have no idea wath did happend to it.
the MDA starts up shows T-Mobile ... an go to the Bootloaderscreen (red IPL2.21.0001, green spl 2.2.0001, blue, with)
so i have tried to flash it now with WM5 from T-Mobil image ver 2.26.10.105 (from this nice Board here
The flash tool shows no image information of my MDA but the posibility i there to push the update button. If i do that the update tool trys to flash a few seconds and stops with error code 294 (invalid vender id). on the MDA is noch change (still bootloaderscreen)
some one of you has an idea wath could be happend to this device ?
or an idea wath can i doo ?
Yes!!!
Your problem... is NOT READ Enough!
So please read how to make a hardSPL cause your wizard is G4....
if you do it well you can upgrade whatever you want but for this time... you need to exit bootloader screen so... perform sofresets! or hardreset!
Keep reading for more chances...
You don't need to apply HardSPL or SoftSPL to flash an official stock rom.
Which language or version was working primarily on the phone before you flashed t-mobile 2.26 ?
Secondly download 'RUU_NoId' or 'RUU_MUN' and replace it with the RUU in the rom and Run the replaced RUU,hope it'll work.
Hi,
and thanks for the answers.
i do not know wath was befor on it. i have get it with the information that there was an klabel inside for the keybord not in the slot .... and after "reparing" - the mda do not boot.
up to now i have update it with orginal firmware and it runs again ... so peraps someone has talk **** to me ?! - now i think it was a bad flash
p.s. the vendor id problem was my mistake, was the wrong update
Hi,
I do not know why my first post got moved, maybe because I did not use a [q] in front of my question? I did use the search function but couldn't find a proper answer to my problem...
Yesterday I have flashed my Dutch Elfin. It was originally working on a Dutch T-Mobile branded ROM which I have successfully flashed to a German modified ROM.I performed the CID unlock as described in several tutorials before flashing the rom and everything went as it should.
However I tried flashing another English ROM which bricked my phone (dunno why). I am now in the red-gree-blue Screen with showing my IPL: 2.81.0002
and my SPL: 2.26.0000
Here are the device details before I bricked the phone:
Touch version : Elfin
Device ID : ELF030050
CID : T-MOB003
IPL : 2.81.0002
SPL : 2.20.0000pof
ROM Version : EPS.3.30.000.1
ExtROM Version : @ EPS GERMANY
Operator Version: None
AKU Version : By Piranha
Page Pool : 12 MB
RAM Size : 128 MB
ROM Size : 256 MB
Model No. : ELF0300
Part Number : 99HEL011-00
MCC+MNC : Not found
I have tried several original roms with most of them giving me a ERROR 270.
I managed to download a Dutch original Rom from the T-Mobile website (http://www.t-mobile.nl/persoonlijk/h...ch-update.aspx) This ROM gave me a ERROR 294 Invalid Vendor ID...
I have no idea what to do now and I hope you guys can help me out to save my phone.
Thanks a lot for your help!
You searched? There is a link to the troubleshooting thread, located in the Sticky at the top.. entitled "Avoid Confusion". Flash a Hard SPL from the bootloader and update your IPL.
bornchilla said:
Hi,
I do not know why my first post got moved, maybe because I did not use a [q] in front of my question? I did use the search function but couldn't find a proper answer to my problem...
Yesterday I have flashed my Dutch Elfin. It was originally working on a Dutch T-Mobile branded ROM which I have successfully flashed to a German modified ROM.I performed the CID unlock as described in several tutorials before flashing the rom and everything went as it should.
However I tried flashing another English ROM which bricked my phone (dunno why). I am now in the red-gree-blue Screen with showing my IPL: 2.81.0002
and my SPL: 2.26.0000
Here are the device details before I bricked the phone:
Touch version : Elfin
Device ID : ELF030050
CID : T-MOB003
IPL : 2.81.0002
SPL : 2.20.0000pof
ROM Version : EPS.3.30.000.1
ExtROM Version : @ EPS GERMANY
Operator Version: None
AKU Version : By Piranha
Page Pool : 12 MB
RAM Size : 128 MB
ROM Size : 256 MB
Model No. : ELF0300
Part Number : 99HEL011-00
MCC+MNC : Not found
I have tried several original roms with most of them giving me a ERROR 270.
I managed to download a Dutch original Rom from the T-Mobile website (http://www.t-mobile.nl/persoonlijk/h...ch-update.aspx) This ROM gave me a ERROR 294 Invalid Vendor ID...
I have no idea what to do now and I hope you guys can help me out to save my phone.
Thanks a lot for your help!
Click to expand...
Click to collapse
dsixda said:
You searched? There is a link to the troubleshooting thread, located in the Sticky at the top.. entitled "Avoid Confusion". Flash a Hard SPL from the bootloader and update your IPL.
Click to expand...
Click to collapse
Thank you for your reply dsixda,
UPDATE: I went through the whole tutoria. I do know my Device ID (ELF030050) and CID (T-MOB003) now and I have found the correct Rom:
RUU_Elfin_TMO_NL_2.26.114.52_4.1.13.52_03.08.90_BL UE_Ship_SPL2.26.exe
Device: ELF030050
CID: T-MOB003
Version: 2.26.114.3
Language: NLD
IPL/SPL: 2.26
I have downloaded that rom and tried to flash it onto the device. Now I get an error ERROR 294 (Invalid Vendor ID). The Wiki tells me that I have probably flashed an old USPL onto my device, somehow causing the device to be "half" CID-locked. Flash a newer IPL and Hard SPL onto your device is the advice that is given. My question is HOW? can I flash a newer ILS and Hard SPL onto my device, how does that work?
I think he means this post http://forum.xda-developers.com/showthread.php?t=445666 , read all what you can, don't panic and eventually you'll be fine
Good luck
tito12 said:
I think he means this post http://forum.xda-developers.com/showthread.php?t=445666 , read all what you can, don't panic and eventually you'll be fine
Good luck
Click to expand...
Click to collapse
Okay, I followed this manual. The update process came to 100% but in the end I got a Error [270]: UPDATE ERROR. I know that the tutorial says that I have to establish an Active Sync connection. My Active Sync tray icon is gray so I assume that there is no connection established. Is there a way to get the connection established even from the rgb bootloader screen?
bornchilla said:
Okay, I followed this manual. The update process came to 100% but in the end I got a Error [270]: UPDATE ERROR. I know that the tutorial says that I have to establish an Active Sync connection. My Active Sync tray icon is gray so I assume that there is no connection established. Is there a way to get the connection established even from the rgb bootloader screen?
Click to expand...
Click to collapse
trayed to take youre original rom and flash again
It is normal AS icon goes gray, continue the operation
tito12 said:
It is normal AS icon goes gray, continue the operation
Click to expand...
Click to collapse
How should I continue because the Hard SPL update process of came to 100% but in the end I got a Error [270]: UPDATE ERROR. What should I do next?
OK, lets try from the beginning, are you familiar with the procedure in this post http://forum.xda-developers.com/showpost.php?p=2415645&postcount=3 did you observe all the steps ?
tito12 said:
OK, lets try from the beginning, are you familiar with the procedure in this post http://forum.xda-developers.com/showpost.php?p=2415645&postcount=3 did you observe all the steps ?
Click to expand...
Click to collapse
Yes, for my first ROM update that went through successfully:
- I did install EnableRapi.Cab & Cert_SPC.Cab.
- no MicroSD Card was inserted
- Active Sync connection was established when I flashed
- then I ran flashed a German Modded ROM
The phone was working fine but I didn't like the Rom. So I flashed an English ROM that didn't go through and bricked my phone...
So try to cid unlock using this uspl http://forum.xda-developers.com/showpost.php?p=2416770&postcount=5 and don't forget sometimes it takes 2 or 3 shots
tito12 said:
So try to cid unlock using this uspl http://forum.xda-developers.com/showpost.php?p=2416770&postcount=5 and don't forget sometimes it takes 2 or 3 shots
Click to expand...
Click to collapse
I can encourage his reply, you need to try several times before it will take effect. Also if you are able to use multiple computers, try some different computers as that also helped for me to unbrick my phone.
tito12 said:
So try to cid unlock using this uspl http://forum.xda-developers.com/showpost.php?p=2416770&postcount=5 and don't forget sometimes it takes 2 or 3 shots
Click to expand...
Click to collapse
Okay,
I have actually done this once already (will try tonight again with different computers) and it didn't go through.
The update process came to 100% but in the end I got a Error [270]: UPDATE ERROR. As I said above already I know that I have to establish an Active Sync connection. However, my Active Sync tray icon is gray so I assume that there is no connection established. Is this important for my bricked device?
Also, does it matter which version I use? IPL_USPL_3.07.zip, IPL_3.10.zip or ELFIN_USPL_310.zip?
Offtopic: are you dutch ?
Is the update process showing on your computer or on your elfin ? if it's the latter it shows there's some kind of connection even if the icon is grey. 2nd question: on the bootloader do you see "usb" when you are connected ?
Cyw00d said:
Offtopic: are you dutch ?
Click to expand...
Click to collapse
nope
tito12 said:
Is the update process showing on your computer or on your elfin ? if it's the latter it shows there's some kind of connection even if the icon is grey. 2nd question: on the bootloader do you see "usb" when you are connected ?
Click to expand...
Click to collapse
The update process is showing on my computer (going to 102%) as well as on my device (going to 100%).
I also see "USB" in my device when it is connected and the usual windows ding-dong.
How do you flash when you only have a single IPL310.nbh or ELFIN_USPL_310.nbh file? (And which one is the right one?)
So far I just copied the file into an old folder that I still have with the ROMUpdateUtility.exe. Then I start ROMUpdateUtility.exe and the update process starts. However I always receive an Error [270]: UPDATE ERROR...
Try a new RUU, flash the uspl and after that the ipl (I have read ipl is less important or not at all ) and make sure in the ruu folder to have only one nbh file : yours
tito12 said:
Try a new RUU, flash the uspl and after that the ipl (I have read ipl is less important or not at all ) and make sure in the ruu folder to have only one nbh file : yours
Click to expand...
Click to collapse
Okay, I have used an RUU from the [ROLLUP]AVOID cOnFuSiOn... Thread. I tried to flash ELFIN_USPL_310.nbh. The process starts an my PC Screen as well as on the phone. it goes to 100% on both devices but then I get an Error [270]: UPDATE ERROR. I have tried this now 5 times in a row but every time I get the same Error.
Then I also tried the IPL310.nbh with the same result (Error 270)... What am I doing wrong
My rgb bootloader screen still says IPL 2.81.0002 and SPL 2.26.0000
Try this, this was my first unlock attempt and it worked well the 2nd time
http://forum.xda-developers.com/showpost.php?p=1964159&postcount=1
Don't loose hope
Or just flash the Unbricker ROM - have you tried that?
http://forum.xda-developers.com/showpost.php?p=2913636&postcount=1
Helle everyone! First of all, sorry for my bad english! However some days ago i read that htc have done a wm upgrade for my phone (6.1) i didn't know that it wasn't for gsm version.. when i did thet upgrade i had on the phone the onyx rom and the cid unlocked, with this upgrade the spl came back to the original but the original rom doesn't start the installation. so i have the spl 2.26.0000 and the onyx rom that doesn't start and when i turn on my phone it remain in the display of 3 colors of upgrade.. what i can do now?? i have the warranty cause i bought the on july.. plese help me, how can explain them this fact? i'm in yours hand..
thank you
Jasper
Hi
I think you should try to cid unlock again, if it works you could flash the onyx again, if not there's a lot to read in here http://forum.xda-developers.com/showthread.php?t=406721
Good luck
i've tried a lot of times to unlock the cid but it give me the error: ERROR [200] Invalid update tool
Please get newer update utility
I used the latest version of spl and it's the same.. I tried to dump the original rom and it give me the same error 200.. Further there is no RUU in the display of htc..
Sorry for the english
Nobody can help me??
Hi JesperHTC-Touch !
Do you use windows xp or Vista to sunc yourè phone?
xp, but i have the phone locket to the bootloader and activesync it isn't green..
Hi JasperHTC-Touch!
I have also got that ERROR [200] Invalid update.
I recomend you to install IPL & SPL 310 you can find it her http://forum.xda-developers.com/attachment.php?attachmentid=130771&d=1226977938
http://forum.xda-developers.com/attachment.php?attachmentid=130567&d=1226919217But use this tool to do the upgradehttp://forum.xda-developers.com/attachment.php?attachmentid=101826&stc=1&d=1217022319
Dont be worry i diddent got the color bar either. But be shure to have at least 50% of battery capacity before yoy do the upgrade. Put the file from (310 inside the catalog in 226 /RUU and replace the file RUU_Signed.nbh that you downloded at press theelf-uspl.exe and read carfully what you seen on the screen and dont dissconnect youre phone before you have started up the phone completely. Thats what i did and it works for me. God luck
Kindly MacRoy
I did what you told, but it doesn't work, i'm triyng to upgrade with all the original rom of this phone.. it's impossible i can't unbrick my phone
Another fact it doesn't enetr in ruu-bootloader.. only bootloader
Try to hard-resetting the phone!
just tried and doesn't work.. i spent 350 euro in july for this phone!!
Hi
try the unbricker rom method mentioned in this thread
http://forum.xda-developers.com/showthread.php?t=446242
it is a trial original rom that can be flashed from SD card then after that you can CID unlock again (good Luck)
dowsn't work :'(
i also tried to unlock the spl from microsd but it give me the error: invalid certificate..
Nobody can help me?? i don't want bring it to the guarantee.. sorry for the bad english..