Hello:
I have a tmobile MDA Vario and recently the green call button has stayed on constantly. At the same time 5 of the buttons on the key pad has stopped working, the blue light on the keypad stay lite even when it is closed.
Does this sound more like a O/S issue or a mechanical issue. Any suggestions from anyone?
Thank you
Related
Hello everybody! I'm having problem with my qtek s200 (with swedish firmware). The background light is turning off every 10 seconds. I can change it back but whenever i turn the monitor off with the red button at the right and then turns it on again it's back at 10 seconds. Anybody have had the same problem or know anything I could do to fix it.
G4 model and I think it's CID-locked..
I have the same problem
I tried changing the registry with no luck
Hello, I have a i-mate K-JAM and it has suddenly stopped working. Whenever i switch it on, the bluetooth light turns on and the camera flash light... sometimes even the keyboard light but nothing works... As soon as i press the power button... poof the lights turn on. Is there anyway to fix my beloved phone?
its not even charging :<.... i think the motherboard is dead...any conclusions?
I've search through:
Gaijin Guide for x01HT
Video Call Button
Hermes Wiki
A bunch of searches have come up empty.
Softbank x01HT
Using Pays Rom WM6.1
or K's Pro rom
Call Button OK.
The Video Button and End Call button however do not work (screen menus work fine)
Any suggestions?
Any suggestions
Buttons not working
If a button stops working, yet you know the functionality still works, then I'd suggest a battery reset. Simply remove the battery from your 8525 (must be completely out) for about 15-20 seconds, place it back into your 8525 and turn it on.
I had to do this back when I had iPAQs and Dell Axims, and have to do it with my 8525 from time-to-time when my camera button stops working. This performs a hardware reset. As long as your battery is in your 8525, there is essentially power flowing within the 8525, even though you have the screen turned off. By doing this, you're allowing all power to drain from the 8525's circuit cards/boards and performing a hardware reset (whereas using the stylus only gives you a software reset).
I hope this helps you!
Thanks. No dice (sorry for late reply).
Changing the os to AT&T clears up the call / end button. The moment I load a homebrew like pays, TnT ... The call/end/video buttons stop.
Very Odd.
I'm getting an xperia, I used to have a tytn II and now have a touch pro.
When I moved from the TYTN II to the touch pro I really missed having hardware keys and the LED blinking whenever the phone was on.
I could only tell if the phone was on by pressing the power button on the touch pro, which meant on a night when I wanted to switch off the phone I end up pressing the button, only to see the phone was already off then have to wait for the phone to start only shut it down.
Can you make the light flash every so often when it's on on an X1? If not is there a way to tell if it's on or off (without turning it on if it's off)?
- Anthony
you could briefly press the power key to see if the screen immediately lights up, if not then it is off
or you could allow waking up the phone with any hardware key and click one of the other keys to see if it's on
I'm sure, with all of the apps and mods on here, there is a way to make your lights blink every so often as well
however, I've noticed the lights aren't very bright, even at night time
You can slide it open to check if it is on
OMG I've been going nuts over this, I didn't think about sliding the keyboard out!
The any key wake is an even better option, thanks.
I'd still like to get the LEDS lit though, as I used to remeber to switch off the TYTN II when it lit up after I turned off the (ceiling) lights.
Thanks for the help
- Anthony
A workaround:
Set SMS or Mail notification lights to "unlimited"
Send yourself a SMS or Mail and keep that one "unread", then you have your Xperia blinking as long as its turned on.
yes, my 612 is encountering this problem. it keep soft reset itself after the party i am calling rejected my call. the screen just shows a black screen, with the green light blinking at the top of the phone. den shortly i am shown the HP blue screen......any1 encountering this problem?
another problem is, after about an hour of phone call, after hanging up, the phone will also soft reset itself....
I faced the same problem recently too when I refreshed my 612c back to the original ROM. Appreciate any help.