Database Users

White Screen only

I just installed this program, used default settings, apllied, My 8125 soft reset.
Now I cannot see anthing past the initial screen that lists IPL and SPL version.
Just a plain white screen, Active sync wont work, no buttons work. Please help !!!!!!!!!!

If you're stuck I think the only next step would be a hard reset which is going to drop it back to the base factory build so you'll lose anything you've installed etc.

How do I hard reset 8125, with buttons only (key / button combination) OS does not boot or visible.

press the "connetions" button (on the left hand side of the unit next to volume up/down) with the "voice" button (right hand side of the unit opposite the connections button) and then use the stylus to do the normal soft reset and it should hard reset back to factory settings - it's described in the manual

Tried hard reset several times, no luck.
All I did was installed registry wizard from here
http://forum.xda-developers.com/viewtopic.php?t=39725&highlight=registrywizard
and now I can't get it to do anything, anymore suggestions ?, your help is really appriciated, I have only had the phone to 2 days and its dead already

try holding the same two buttons and then hitting the power button instead of the reset thingy... this method was easier for me... If this dosen't work you will have to enter bootloader mode and reflash the rom.
For the detailed reset procedures try here
By the way, did you use that program to change the default input method?? I use it all the time and the only time it gave me the whitescreen is when I tried to change the default input...Oops. I believe that you should be able to use that program safely, just leave the default input alone... Hope this helps.

Thanks for info, I did manage to reload the ROM. and Yes I did change the default input method, that might have done it. Thanks all, for your Help.

raheelb did you have the warning that the proggie cannot recognize the AKU version?
I had had such a warning, unfortunately bypassed it and had the same issue (white screen) - any one knows why the RegistryWizard cannot recognize AKU version? I have the original Qtek 2.17 ROM installed... :?

my k-jam hangs

Hi,
Recently my pda(k-jam) fell from my pocket and it hanged. I did a soft reset but I get this error message "Press Send to restore factory defaults, Other keys to quit"
I tried all keys but in vain. I then did a hard reset by pressing the comm and the voice dial. (did a reset with my stylus). I still get the above error message.
Does anyone have any suggestion or idea how to reset my pda?
Thanks alot.....

Y dnt u flash it with a new Rom look around the forum for the new MOSKI ROM.

Thanks
Thank you for your suggestion, I will think of upgrading to molski.
But will it upgrade ? As a hard reset also doesnt seem to work and how do I get to reach the ROM if I am not able to see the other things?
Thanks

Please help...
Hi ,
I am a newbie and so would seek alot of help. Thanks in advance...
Couple of days back my pda fell and now after soft or hard reset the screen still shows this "press send to restore to factory defaults, other keys to quit"
I would like to upgrade to molski but they say I might have to downgrade my rom but I must first unlock the device. There are g3 or g4 device..how do I know what device my k-jam is...g3 or g4? How do I follow up or know?
Could anybody give me the link or solve my problem? As my k-jam just wont pass that screen..I tried looking into various topics but couldnt go about the first step I should be taking...
Please help!
Thanks

Hi,
Please help..after hard reset, it still does not happen to load into the factory defaults... I cant flash my ROM or anything ...as it wont progress further than that screen ... "Press Send to load factory defaults, or quit"
Anyone have any suggestion?

Hold down the camera button while resetting it. If you can get it to the bootloader (three color screen), you might be able to flash it with something and possibly rescue it. It does, however, sound like you might be screwed. Things break when you drop them, including plastic phones.

hi
Thanks but if I have to do a hard reset, I would already be holding the comm manager and the voice dial with the stylus to reset. Do I hold all the 3 buttons together while hard resetting ?
I have tried all the buttons after doing the hard reset but just doesnt get to the other screen.
Thanks for your help.

Hold down the camera button, Power Button and Pin in the hole. First relese the hole, then release the power button and keep holding the Camera button dis will bring the Tri-colour screen. There'll be some info. like IPL n SPL der
If IPL n SPL are like:
IPL 2.xx.xxxx or 1.xx.xxxx
SPL 2.xx.xxx or 1.xx.xxxx then ur device is G4.
if its like:
IPL 2.xx or 1.xx
SPL 2.xx or 1.xx then ur device is G3
if its G4 you need to CID Unlock that before upgrading it.
All the LUCK. Go Ahead.

Hi
Thanks,
I tried your steps but it still wouldnt work. But somehow I did the switch below the comm button and it showed me the screen to the somethign HTC innovation or like that.
I think I had to tinker with the switch below the button to get the screen working.Thanks for your help.

Please Help me Qtek s200

I have a qtek S200:
IPL 2.09
SPL 2.09.0000
GSM 02.07.20
OS 2.13.9.26
I have a problem, y qtek starts and goes until the "windows Mobile" Screen and then it stop.....and it stays in that screen for ever.........please help me out, i tried to hard reset and it doesn´t work what should i do?
Help me please!

What was the last thing you did before it stopped working?
Did you install something?
Are you sure you preformed hard reset? You must hold power + camera + comm manager buttons (all on the sides) then press and release the reset hole (at the bottom).
Then you will see a question asking you to confirm hard reset. If I remember correctly you need to press 'send' (the green phone button) to preform hard reset.
Please be sure to read the instruction on he screen.

See the wiki:
http://wiki.xda-developers.com/index.php?pagename=Flash_From_Bootloader
You have a G3 device, so make sure if you use a RUU, you use a G3 specific one.

levenum said:
What was the last thing you did before it stopped working?
Did you install something?
Are you sure you preformed hard reset? You must hold power + camera + comm manager buttons (all on the sides) then press and release the reset hole (at the bottom).
Then you will see a question asking you to confirm hard reset. If I remember correctly you need to press 'send' (the green phone button) to preform hard reset.
Please be sure to read the instruction on he screen.
Click to expand...
Click to collapse
thanks man it works, thank u a lot

Helping hand, please

I just got x01ht from japan. It's stuck at windows mobile screen.
Herm200
ipl-1.01
spl-1.09
radio 1.14.00
Advices or just point me in the right direction
Thx in advance.

1st of all, try to remove battery for 10minutes and then switch on.

Thx, but that didn't work.

Hello,
Can you explain what was the last think you've done... because my crystal ball didn't work today I really hope that you didn't start to flash something before HardSPL, which you don't have.
Try to Hard reset the device:
Code:
Press and hold the Left SOFT KEY and Right SOFT KEY, and at the same time, use the stylus to press the RESET button at the bottom of your device. You will be presented with a menu saying 'press R to reset, X to exit', if you press R Your device will be set back to factory default settings. (The L/R soft keys are the "- -" keys just above the start and OK buttons)
If it still doesn't boot, continue with reading
The best thing you can do right now (if your device is still in warranty) is to take it back. If it out of warranty, then start reading here. Check SPL column where point at:
Code:
[B] 1.06, 1.09, 1.11 or 2.02 [/B]
Good luck

no one want reply me :=(

with big mistake i was flashing my ELF with a wrong rom( svp s650)..
it unbootable I tried everytings hard reset soft reset nothing changes: = (just the green light that stays on ..
help plz and thanks
Reply With Quote

muslim2009 said:
with big mistake i was flashing my ELF with a wrong rom( svp s650)..
it unbootable I tried everytings hard reset soft reset nothing changes: = (just the green light that stays on ..
help plz and thanks
Reply With Quote
Click to expand...
Click to collapse
Hi
Sorry to hear your problem, try to read this guide http://forum.xda-developers.com/showthread.php?t=406721 and the stickies in the Elf Upgrading
Hope you can save your device

i have read it but i dont find the sollution :=(
can you help me plz ????

muslim2009 said:
i have read it but i dont find the sollution :=(
can you help me plz ????
Click to expand...
Click to collapse
Hi
Does it go into bootloader (3 colors )?

no no bootloader...
just the green light that stays on
i was tried bootloader and soft resest and hard reset nothing :=(

nothing again
no no bootloader...
just the green light that stays on
i was tried bootloader and soft resest and hard reset nothing :=(..
if you can give a vedio explean how i can result this problem..
and big thanks from morrocco

muslim2009 said:
no no bootloader...
just the green light that stays on
i was tried bootloader and soft resest and hard reset nothing :=(..
if you can give a vedio explean how i can result this problem..
and big thanks from morrocco
Click to expand...
Click to collapse
Hi muslim2009
I tried a few searches but all the results say you need the bootloader screen , are you sure you didn't miss a step in hard reset or bootloader mode :
To enter the bootloader:
Hold down the camera button and reset device with the stylus. Keep holding the camera button until you see 'tricolor' bootloader screen.
An alternative way to enter bootloader:
Switch the device off by long pressing O/I (power) button. hold down the camera button while pressing the O/I button about 1 second. Keep holding the camera button until you see 'tricolor' bootloader screen.
Alternative(universal?) bootloader(3)
As almost all htc smartphones with onboard camera, when you push and hold the camera(photo) button, and plug in usb adapter. Even a "stupid" usb power adapter will work.
To hard reset:
Hold down send/reject buttons (green/red at the front) and reset with the stylus; release the stylus but keep holding the buttons till you get 'this will erase all your personal data' message, then press 'action' (big front button) to hard reset.
I sincerely hope it helps
I was also born in Morrocco at Casablanca and lived there until age 16. Anyway I'll continue searching.
Tito

thanks for help,but it won't work :=(..
[email protected]
add me if i can show you my htc ..
thanks from morocco

I'm not sure if it's possible with the HTC Touch, but I know when I was playing around with an old iMate SP3i (smartphone) I was able to do a ROM upgrade from files on the memory card.. Took me a few attempts to get it right, but it worked. I think I also upgrade my SP5 to WM6 from WM5 that way, but I'm not too sure about that.
Either way, a basic idea of what I'm talking about can be found here, but that is obviously for a different phone.. Maybe some of the more common members here would have better luck finding a similar process on a Touch....?

maybe its will be workin but what marterial i will need for this opperation??

On some HTC devices (cheetah, for example) if you put the ROM file (.bin) in the root directory of the SD card, the phone will flash directly from the SD card.
I think you do require to put the phone into bootloader for that to work though ... not 100% sure, but probably worth looking up.

Ok... Been trying to search for more information for you, but with not really knowing all the correct terminology it's taken me a while longer than I thought. I've found two threads that have some of the information I was looking for:
Recover / Revive your dead / bricked HTC ELF or ELFIN
Recover HTC Touch from tricolors RUU boot-loader (Mtty)
The second link is actually found inside the 2nd post (I think) of the first thread I mentioned here, looks like they are linked in some way. Your best bet is to read through and see if it is something that may help. Let us know if this works for you...?

thanks you man,i was read the first link befor..i will see for the second
hope will work.thank you again