Database Users

Help! Weird problems on my jasjar

I have a jasjar recently and had problems turning off at 50 percent. It was working fine as long as power odesnt drop below 50 %. Then I bought a desktop charger (made in china) and started charging from there. That's when all this weird problems started.
When I put the fully charged battery inside sometimes it doesn't power on by pressing the power ubtton so I have to reset it to turn on. Sometimes it doesn't turn on with reset so I have to go to bootloader then reset just to turn it on. Sometimes it just won't turn on! If it does turn on sometimes the screen is white! When it does boot properly and go on standby. The lights blink but it won't wake up so I have to reset it. Sometimes while using it, the screen would just turn garbled white.
This don't happen all the time, Im actually typing this post using my jasjar and even if I charge the battery using the phone, it exhibits the same problems once in awhile.
SOLUTION FOUND!!! READ THE LAST THREAD
Any ideas? Could the battery be doing this or is my jasjar messed up? Please help!

I downgraded to wm 5 Helmi ROM and seems to work for now. I was using Helmi's wm6 so I don't know if that attributed to that. Will update.

Still didn't help.. Any ideas? Is my jasjar dying? Please help!

Battery issues
Here and elsewhere are postings which make it apparent that some after-market batteries don't work well with the Jasjar. Some electronic devices are relatively fussy about voltage and amperage levels, and some off-brand batteries are fairly wide of the mark in those regards. Not necessarily on the low side, either.
The problem is not limited just to computers. I had an electronic remote reading thermometer whose display went nuts; the manufacturer asked whether I was using EverReady or Duracell batteries. When I replied no, I was using Ikea batteries, they told me I had to use EverReady or Duracell batteries or I was likely to encounter the problem, and they're right: using those batteries fixed the problem. Not that the Ikea batteries were bad, mind you: their power level (voltage and amperage both) were actually too high, according to the manufacturer, and my VOM tester confirmed their assertion.
Somewhere on this forum is a link to an eBay supplier of batteries which work reliably in the Jasjar. Good hunting! Cheers,

Thanks but I'm using the original battery. So do you think that the desktop charger did something to the battery?

may be it caused by a desktop charger. When i used a chaeger made in chine for my alpine, sometime the screen goes white, or ALL buttons seems die (All button didn't work). The most terrible is that charger make my dive hard reset 2 times (first time i din't realise if it cause by my charger, then i just install all progs but when i charge, it hard reset again).
Even for 5 days after i bought it run well, except the ringtone goes on silent every time i charging.
Now i throw away that thing.

So its the charger!! GRRR...Anyways, even when I'm using the Jasjar to charge, everything is the same. Lockups from standby, white screen..You think I should try another battery? Any ideas?

Weird stuff / battery related?
Hi there,
dont know if anyone is reading this thread coz it is kinda old, but i have the same probs mention as above. I have the orginal bat and charger which came with the device. I also uses a car charger sold from my phone provider.
now after 14 months i have the weirdest things like shutting down randomly when the bat is about 58 thru 50 percent. I can not start the device again coz it stops in the middle of the boot process. It only starts when i connect it to a laptop by usb or to the standalone charger...
I tried differnt roms found here and radio roms but it doesnt help...
my guestion: does any one know if this prob is solved when I buy a new battery? or is it wise to thro out this universel suck device ( I have had so much probs with this device so neglect my tone...)

XCube said:
Hi there,
dont know if anyone is reading this thread coz it is kinda old, but i have the same probs mention as above. I have the orginal bat and charger which came with the device. I also uses a car charger sold from my phone provider.
now after 14 months i have the weirdest things like shutting down randomly when the bat is about 58 thru 50 percent. I can not start the device again coz it stops in the middle of the boot process. It only starts when i connect it to a laptop by usb or to the standalone charger...
I tried differnt roms found here and radio roms but it doesnt help...
my question: does any one know if this prob is solved when I buy a new battery? or is it wise to thro out this universel suck device ( I have had so much probs with this device so neglect my tone...)
Click to expand...
Click to collapse
I bought my Universal (Jasjar), used, almost a year ago and use it daily. To date, I haven't had this problem, but I'm anticipating it. Yeah, I'd say it's almost surely your battery (they don't live forever), just be careful to replace it from a reliable source.
Sorry you don't like the device; I've thoroughly enjoyed mine! Cheers,

Hi,
I guess u r right, batteries will die. So I ordered a new one, I will let you guys know if it helps. I bought the qtek 35H00058-00M battery which is the orginal bat
The thing is, normally will a battery be faster drain so it would become faster 0 or 10 precent, instead this piece randomly shutting down or switches off in the middle of a phone call.
I have a Blue Angel as well, now for more then 2 years, which is charger daily just like mine unversal. The batt of the Blue Angel outruns the uni with bat life. Never had this weird stuff with the ba, like shuttingdown without a warning.
Well I will see if a new bat will fix the trouble, tomorrow my new bat will arrive.
cheers.

I also have the same issue with the 02 Exec. It switches it's self off when the battery reaches below 50%. I have ordered a new battery. Will let you know if this still happens once it arrives.

Well,
I already knew it but now its for sure at my end. HTC and ms together gives u pretty expansive CRAP.
Got my new battery which was carefully chosen because of other rumours of battery problems. I bought exactly the same battery from QTEK as the original.
Yesterday i got the battery, left it alone to get on room temp. this morning switch it with my old battery.
1. First thing what i found strange was that my **** device said it was at 100%
2. after 45 min I had the same bat prob as with my old battery
3. device can not be started on bat power, which would let u think that the bat would be ZERO procent. However turning the device on when on wall power this **** device says that the bat is 100%, but disconnecting it from the wall power it shutdowns right away.
conclusion:
the new battery is worse then the old bat. the only difference between them is the serial number. same type same manufacturer.
I was already think of buying a non HCT / Micro**** mobile device, but today after 14 months of trouble and losing important phone calls I am going to say good bye to this universal crap.
I wise u the best with our device but for me it ends here.

UPDATE:
Used a 3800 mah battery from expansys, made in Taiwan by Dyna and still same problems...not battery related at all...Anybody got a mainboard they can sell me...even a broken miniusb.

Problem and solution found
The Problem is a faulty voltage controller in the mainboard causing Bulverde CPU to hang and give funny colors to the screen
Solution is to disable Cpu scaling of Bulverde by using pocket hack master and setting speed at 312mhz before turning it of or closing the screen. You could always set it at 520 when using it but before turning it off make sure speed is 312. Hopefully this helps others with this problem.

Charmer wont turn on

this is my firends phone - tmobile cmpact 2 - its never been cooked, standard wm5 rom and no upgrades or downloads. it suddenyl today entered bootload screen - we took out the battery restarted, then it loads to the tmobile splash screen the cuts off, now it wont even turn on
tried charging it, and the charge light doesnt ocm eon, any ideas??
Thanks

anyone?..........................................

You have to enter bootloader mode (look up the wiki for how to) and then run the official rom upgrade for charmer.

my charmer is also dead
right in the middle of typing in an adress at iGO on my Charmer with WM5 it started rebooting and turned black after the T-Mobile bootscreen. And I could only turn it on by removing the battery, waiting for some minutes and then turning on again, just to see the same thing happening - black after T-Mobile screen.
Now I cannot turn it on at all, cannot reset (neither hard nor soft), cannot get into bootloader nor can I charge it (at least no LED is indicating anything).
Does anybody have an idea? vlodeck?
At the moment I am not at home, so I cann't try the original power supply (so far I used the one in the car).
Thanks in advance!

There are two possible outcomes Jared.
Either your power supply in the car is not enough to lift up Charmer.
Or your battery went totally dead, in which case you would have to buy a new battery.
Good luck.

Thanks for the fast support!
the strange thing is, that it all started with battery at about 80%...
I will check on sunday with the original power supply and a battery from another device. Then I will let you know the outcome.

I can lend you my battery, Jared!
...to see if it is really the battery.
Otherwise I can only recommend the HTC Kaiser ;-)

problem solved for now
thanks frikibaby for the offer...
but vlodeck was right. At home I pluged in the charger and it started charging and I can also turn it on again. So for some reason my car charger does not charge the charmer anymore although the indicator and the battery bar says so ...???
Thanks for the support!!

Jam Battery Meter Problem..

Hi everybody,
I'm having a strange problem with my i-mate jam.. I've replaced the battery 2 months ago with a new one. The new battery works like a charm.. I can make calls with only 6% of charge..
Anyway, about a week ago, the battery meter started jumping all over the place; all of a sudden the meter would show 100% charge then change to "Charging" state with 0% charge (both the primary AND the backup battery)!! Then in a while change back to 100%, then eventually it goes back to the real charge value (65% for example).. And then it goes to 0% "Charging" and so on.....
When I connect the charger, the device shows the right charge value, but sometimes it gets stuck @ exactly 81% even after 2 hours of charging, the LED is constantly yellow as usual but I can see a green flash every 8 seconds or so..
Sometimes, the device behaves correctly and charges to 100% without any problems, but when that problem happens it gets so irritating and annoying, and I am totally confused about it coz I can't make out a logical explanation to why this keeps happening.. I didn't install/uninstall any new programs.
Do you guys know anything about that problem??
Thanks ahead for your replies..
P.S: here's my ROM info:
ROM version: 1.11.00 WWE
ROM date: 03/14/2005
Radio version: 1.11.00

does the old battery also behaves like that?

does the old battery also behaves like that?
Click to expand...
Click to collapse
No, the old battery never behaved like that.. It's a new problem. Anyway, I discarded the old battery so I can't tell if it behaves the same or not.
As I'm writing right now, the phone is connected to the laptop via USB cable, the LED is yellow and the "Power" menu shows 0% battery and "Charging" status! It's been like that for almost 30 mins now! I have no idea what's going on, the phone appears to be charging but the power meter indicates 0%!!
Could it be something with the charging circuitry??

Sound like a typical hardware problem.

Sound like a typical hardware problem.
Click to expand...
Click to collapse
It could be. However, the meter has been behaving normally for 2 weeks now. And I'm linking the problem to low temperatures. Apparently, the new battery is of poor quality, so when the ambient temps. go below 12C the metering circuit starts showing false values.
I'll keep monitoring the problem and report if anything new happens.
Thanks all for your help.

i'm not sure but here in New Delhi when the temperaures have come down to almost zero, my device sometimes starts behaving like this but it corrects itself in about 5 seconds.and the battery is what was bundles with it and has been working perfectly from past 2 years.

o2 xda exec battery problem

hello, sorry for my english, but i'm italian;
i have a little problem with htc pu10 (universal) branded o2 xda exec:
when the battery charge go to 40 / 35 %, the pocket device is automaticaly turned off, and the only way to turn on the device is connect it to a pc, or battery charger.
When i do this, the led flashes red for a little time, and after 15 seconds become orange, the charge begins, and the device is turned on.
why this??
i have purchased the device 2 years ago, has always done so, but now i need to use it as modem, and the battery and the battery last very little.
please help me!

Welcome to forums
The best you can do is replace your battery
Have a deep read here also:
http://wiki.xda-developers.com/index.php?pagename=UniversalSmallBattery
And:
http://wiki.xda-developers.com/index.php?pagename=UniversalBatteryIssue

ok thank you for the answer, i try to search and purchase a new battery pack on ebay, and i try to use it, if the problem is resolved, better, else, i rewrite in the forum.

Let Andriod die now have a paper wheight

ok here is the problem.
4 nights ago i forgot to plug in my hd2 while android was running and the battery died.
the next morning i went to turn it on and the screen no longer turns on but the phone does boot. the battery doesnt charge, status light doesnt either, end key doesnt work, when i answer calls no noise can be heard or made.
any hope?

Im guessing you cant run bootloader?
Maybe this is a warrenty jobby

If you know someone with another HD2, Try swapping the battery.

chrisizzle492 said:
ok here is the problem.
4 nights ago i forgot to plug in my hd2 while android was running and the battery died.
the next morning i went to turn it on and the screen no longer turns on but the phone does boot. the battery doesnt charge, status light doesnt either, end key doesnt work, when i answer calls no noise can be heard or made.
any hope?
Click to expand...
Click to collapse
does it enter in bootloader mode?
retry flashing wm rom+radio

chrisizzle492 said:
i went to turn it on and the screen no longer turns on but the phone does boot. the battery doesnt charge, status light doesnt either, end key doesnt work, when i answer calls no noise can be heard or made.
Click to expand...
Click to collapse
Hi Chris,
Please eleborate/clarify your OP, because I don't think anyone gets this... At least i don't! You say the screen doesn't turn on but the phone boots?! How do you figure that? Your device is actually on because you can receive/answer calls!?! :S
Sounds like your device has just BSOD (Black Screen of Death) which is discussed quite a lot here. Just press reset button or pull the battery (please tell me you have tried that before...).
If your device IS NOT powered on, please try this:
Does the device vibrate shortly when pressing the End-button? If so you should leave it connected to the charger for longer. If battery has drained too much it takes a while for the device to allow it to power itself up (prevention of overdrainage, which Lithium-batteries don't like very much).
Do you charge through USB, or with the supplied charger? I've had this before trying to charge it with a (different brand) microUSB charger. Turned out most chargers only give out 500mAh, whilst my normal charger (and car-charger) give out 1000mAh i believe. That might help.
You can order a cheap replacement battery from China (i got mine with dockingstation), which is already charged about 60% (for storage purposes).
BTW if your problem is fixed, please add the prefix [FIXED] or [SOLVED] to your topics title.

shufflez said:
Hi Chris,
Please eleborate/clarify your OP, because I don't think anyone gets this... At least i don't! You say the screen doesn't turn on but the phone boots?! How do you figure that? Your device is actually on because you can receive/answer calls!?! :S
Sounds like your device has just BSOD (Black Screen of Death) which is discussed quite a lot here. Just press reset button or pull the battery (please tell me you have tried that before...).
If your device IS NOT powered on, please try this:
Does the device vibrate shortly when pressing the End-button? If so you should leave it connected to the charger for longer. If battery has drained too much it takes a while for the device to allow it to power itself up (prevention of overdrainage, which Lithium-batteries don't like very much).
Do you charge through USB, or with the supplied charger? I've had this before trying to charge it with a (different brand) microUSB charger. Turned out most chargers only give out 500mAh, whilst my normal charger (and car-charger) give out 1000mAh i believe. That might help.
You can order a cheap replacement battery from China (i got mine with dockingstation), which is already charged about 60% (for storage purposes).
BTW if your problem is fixed, please add the prefix [FIXED] or [SOLVED] to your topics title.
Click to expand...
Click to collapse
i have restarted many times.
i use the wall charger.
but why would the phone boot but not turn on the screen or have the mic work?

remove your sd card and the battery. you may have to hit the rest button on the back after you plug the battery back in as well, but as long as you have the sd card out it should come back on. try plugging the phone into a charger and then remove the battery as well sometimes it'll wake it up so to speak. it's just a matter of playing with it. mine did the exact same thing and i freaked out for a little bit.
now if after all this it doesn't work and you've played with it for a while then yeah, best of luck to you =\. but whatever you do in playing with the battery and the charger, keep the sd card out until you can boot into winmo.
EDIT: never mind, i thought the phone wasn't booting. i misunderstood, but i went back and reread the original post. try reflashing your rom if you're in winmo and experiencing those issues. or take the sd card out and reboot.

i would suggest making an backup, as your phone turns on you should be able to estaplish a remote-connection with some (3rd-party-)software and do a hardreset.
if this wont work i would recommend setting it back to factory default (revert hspl if you have one and install stock rom) and send it in for warranty.
seems to be some major problem...
All this steps should be possible without screen turning on (working touchscreen may be needed for backup, but flashing doent need screen input)
if drive-mode is default for your usb connection and holding you from flashing you can do a hardreset and afterwards active sync will be default again and you can establish an active sync connection and flash

check if any of the pins that contact the battery are bended or broken, try to avoid removing the battery when you have to reset your hd2 because the pins are fragile

similar thing happened to me just last night!
I tried the jmz dual boot last night and I was nearly out of battery. I didnt look at any instructions I just installed it and restarted the phone to check out the new toy. it finally got done loading I chose android right away and I was walking towards the bedroom. when I went to see if android had fully booted and plug in the phone I had nothing! It was off. I decided that the battery must have died so I tried to turn it on and all that happened was the tmobile flash screen came up for a second and then it went right off, I got so desperate that I was going to do a hard reset but that wouldnt even work! the boot loader screen would just shut right off. I was suggested to try another battery we had at the house and bang it fired right up I took a wiff of my other battery and I dont know what happened but I think I let the magic smoke out cuz it is fried!

chrisizzle492 said:
ok here is the problem.
4 nights ago i forgot to plug in my hd2 while android was running and the battery died.
the next morning i went to turn it on and the screen no longer turns on but the phone does boot. the battery doesnt charge, status light doesnt either, end key doesnt work, when i answer calls no noise can be heard or made.
any hope?
Click to expand...
Click to collapse
hello friend...i have a problem similar to this. basically when my phone is in android which i use alot if it dies in android, when i reboot it it will turn on for about a second to see my splash screen then turn itself off (the battery is obviously flat). so i plug my charger in and it stays on now but doesnt indicate charging....i boot it into windows mobile and the batt just stays at 0% but its still working. however once i unplug it it will die.....its like the battery is not in the phone. luckily i have two batteries and a dock which charges batteries, so i replaced the battery and everything works fine. once the battery that died in android was fully charged i tried it again and it was fine.................im guesing the moral to this story is dont let your phone die in android mode

I do notice my HD2 runs hotter while in android than while it runs in Windows.
I am not sure if that's an issue to this, which is why I never mentioned about it being hotter. Although my HD2 is noticeable hotter, it never gets to a point that I think I should unplug the USB due to overheating concern...
Just a few inputs from passed experience
I use TMOUS Stock 2.13.531.1 WWE ROM
2.12.50.2_2 radio (not stock)

k going to tmobile today to see if they have any extra batteries i can try.
then ill update

i went to tmobile. and while i was there i noticed the screen was turning on but very dim without backlight (barely noticable). but the rep helping me did not notice and i let it stay that way because tmobile is sending me a new refurbished phone as long as i send the old one (and the rep was totally cool he uses xda also and said they wont check my software and if they do they wont ask for the phone back). he also let me get insurance in case this happens again, instead i will just say its lost. so i basically killed 2 birds with one stone