Wheres this bit go? - 8125, K-JAM, P4300, MDA Vario General

I took the back off my vario to fix the loose stylus problem, on reassembling I could not find a place for the attached piece! Anyone have any ideas

If I had to guess, it goes at the bottom of the stylus hole -- it looks like the piece that retains the stylus in the hole.

Thanks 3waygeek, looks a fit to me, I wondered if the clip had to make a connection somewhere. Working okay anyway, cheers m8.

Just pulled my Wizard apart to do the silicon solution to the loose stylus. Even though I was extra careful to make sure that nothing loose fell out, I found the same part stuck to the side of the speaker (magnet). I can't for the life of me see where it can go. It is designed to make contact with some part somewhere in fact it reminds me of an earth strap of some kind. I can't see how it can go anywhere near the base of the stylus. Any suggestions???

Related

Rubber Keyboard Bump Stops

Not sure whether this should be asked in accessories or not, but has anybody found a solution to the inadequate height of the rubber bump-stops on the O2 Exec? Their height isn't quite high enough to prevent the keys touching the screen's part of the clamshell so you end up with the keys getting rubbed smooth, and marks on the case where they touch.
At the moment, I've got a couple of bits of sticky rubber foot on preventing the touch, but they are moving around on the adhesive since there's so little of it.
What we could really do with is somebody with manufacturing facilities to create replacement bump-stops that are taller than the original ones, unless anybody else has a solution?
Cheers,
Steve.
Nobody got a solution to this?
Cheers,
Steve.
Haven't noticed the problem until you mentioned it but that's because I've been keeping my unit in a leather case -- which actually prevents it from closing comppletely (I'm using the piel frama case with the new clear plastic cover)
Not sure how I would cope with a case - how do you rotate the screen or put it into a Brodit holder without having to take it on and off all the time?
Cheers,
Steve.
You can rotate the screen by opening the flip cover of the case (ie: PielFrama; XAX case sold by expansys; and many others) Not too sure about your Brodit holder w/ a case though.
Surely there must be a good solution to this? I'd pay good money(well, some) for a set of bump stops that were tall enough to stop the keyboard touching. A bit of a design flaw, I guess...
Cheers,
Steve
what I do is, I sandwich a small cleaning cloth in between....this way, I have the cloth at all times to wipe the display when needed....and also protects the screen and the surroundings from touching the keypad! I use the cloth that came along with my screen protector....
have a great new year!
San
Hi
Has anyone got any ideas about where I can get replacement rubber bump stops (normal or extended height) for my Exec? One of mine has fallen off and got lost. I have tried contacting O2, but short of sending the device back for repair, which I don't want to do, they cannot help.
Thanks for any info.
Mark
I have same problem with my QTEK 9000. I have shiny dots obeside my Universal's screen which corresponds to where the keys are located on the keayboard. I believe this is a manufacturing defect, right?
Anybody was able to return their device because of these spots? I've had my device for 1 month and they're starting to irritate me.
StevePritchard said:
Not sure how I would cope with a case - how do you rotate the screen or put it into a Brodit holder without having to take it on and off all the time?
Cheers,
Steve.
Click to expand...
Click to collapse
Maybe I'll screw a belt clip to my brodit car mount. A simple unclip from my belt and then clip it onto the car mount. It'd need some sides on the mount to keep it from rotating due to gravity but I could see this working. Anyone have contacts with Brodit and a good case maker?
Tron_Of_Borg said:
StevePritchard said:
Not sure how I would cope with a case - how do you rotate the screen or put it into a Brodit holder without having to take it on and off all the time?
Cheers,
Steve.
Click to expand...
Click to collapse
Maybe I'll screw a belt clip to my brodit car mount. A simple unclip from my belt and then clip it onto the car mount. It'd need some sides on the mount to keep it from rotating due to gravity but I could see this working. Anyone have contacts with Brodit and a good case maker?
Click to expand...
Click to collapse
I think I would rather find somebody who can manufacture taller rubber stops to replace the existing ones...
Cheers,
Steve.
Rubber Keyboard Bump Stops - possible solution
I've had a bit of a play with my Exec - my friend has lost one of his rubber bump-stops, so I prized one of mine out with a jewellers screw driver to find that they are just pushed in, and so it would be relatively easy to lose them, I think.
Using the same thin screwdriver, I applied super-glue to the recess into which the rubber stop sits, and then pushed the stop back in, but not all the way. Now I have a pair of stops that sit about 1-2mm proud of where they were originally, and they are glued in to prevent loss.
I'll try and remember to post back in a week or two to let you know how I get on with them.
Cheers,
Steve.
I sure hope that there isn't a seam down there where the rubber feet were! I'd hate to hear of a PCB glued to the underside of the keyboard cover.
You can see that there are internal components below the recess, but that's why I applied the superglue with the screwdriver around the inner edge of the recess, as opposed to just squirting it into the hole.
As long as you don't flood the hole with glue, none of it will drop through to the components beneath.
Cheers,
Steve.

stylus problem in/out

hello to everybody!
i got my xda trion 2 weeks ago. after one week, it was impossible to bring the stylus into the xda. so i got a new one.
after again one week, the stylus wont come out of the trion.
someone else prob's with the stylus?
greetings
karl
+ 1, probleme like a wizard too
same ting happened with my TyTN today...
+1 with one week old tytn
Same here...
First I couldn't get it out / then I couldn't get it in / then it would simply slide in-and-out freely to the point that only gravity was holding it in place (sorry if this sounds dirty, but this is what happened).
Had to have mine replaced. I've heard this issue has been around since the Wizard...
I really hope I don't have the same problem on TyTn #2!!!
After a few days of having mine suddenly the stylus was becoming enromously difficult to remove. At one point it just wasnt moving so after a forceful tug it pulled out and a tiny transparent square of plastic/rubber fell out with it. Looks like it was in there to keep it in place but i have no idea how to put it back in. Now the stylus removes fine and stays in place too :shock:
I had the same problem.
Could not get the staylus in with my TyTN.
So I did the mistake and pushed it in... a "knack" sound alerted me that something bad happened. Could not get the stylus in still... so I yanked a small rubber plastic piece from the stylus hole on my TyTN. Now I can slide easily the stylus in.
From teh reports I heard my guess is that the rubebr plastic inside the TyTN is used to firmly hold the stylus in. While without this rubebr plastic there is nothing to hold the stylus until you fully place it inside the TyTN.
andmjones said:
After a few days of having mine suddenly the stylus was becoming enromously difficult to remove. At one point it just wasnt moving so after a forceful tug it pulled out and a tiny transparent square of plastic/rubber fell out with it. Looks like it was in there to keep it in place but i have no idea how to put it back in. Now the stylus removes fine and stays in place too :shock:
Click to expand...
Click to collapse
Same here TyTN 1 week old.
same here,
think I'll swap mine over for a new one.....
raptorian said:
I had the same problem.
Could not get the staylus in with my TyTN.
So I did the mistake and pushed it in... a "knack" sound alerted me that something bad happened. Could not get the stylus in still... so I yanked a small rubber plastic piece from the stylus hole on my TyTN. Now I can slide easily the stylus in.
From teh reports I heard my guess is that the rubebr plastic inside the TyTN is used to firmly hold the stylus in. While without this rubebr plastic there is nothing to hold the stylus until you fully place it inside the TyTN.
Click to expand...
Click to collapse
Same here in 5 days
happend with me after 2 weeks. I've been struggling for a week, and now it's workng again! Don't know how long it will last. I hope it won't brake down, I bought Hermes thrue internetshop. Always sick to return things.
I carry something like this, and only use the tytn stylus in emergencies. I'm hoping this will reduce wear.
Same here - less than 2 weeks.
:shock:
Same here 5 days, luckley I had a replacment on order for BT problems recived that today lets see how this one goes.
me 2
my TYTN's stylus wouldn't stay in the hole.
i sent my tytn to be replaced (due to BT problems and screen alignment)
and i hope i t won't happen again.
when i put the tytn in the box to be sent so the stylus stopped falling :? )
that is odd
My stylus is a little difficult to remove at times, so I had a look down inside the stylus hole and it appears that there are three of those little pink rubber squares protruding from the side and a dark rubber 'socket' at the end to grip the tip when it's fully inserted. The pink squares are obviously there to provide a little more grip along the length of the stylus, but my guess is that even without them the 'socket' at the end would hold the stylus in place. I imagine that over time the pink rubber will either soften up or disintegrate entirely with the friction.
Solution stylus problem
I had the same problem with my stylus, my solution is take a Poster Buddy Brand name Pritt it is so called here in Holland you can place posters and photo's with it on wals, doors etc. looks like white rubber glue, think I see it in the UK with the name Sticky here you can buy it with photostores and bookstores etc. Take a small piece of it turn it between your vingers to a small ball and put it in the stylus hole after that push it to the end with your stylus.
After I do this I have no further problem with the stylus it works great.
Same issue here... the 2nd day I had it a small transparent square rubber went out of the stylus hole. Now i can put it in and out without problems...
Loose/Jammed Stylus
I'm afraid sending device back for replacement/repair for the stylus problem and loose locking keyboard may only be a temporary fix. Having had my device dismantled I can see exactly what the problesms are with both stylus and keyboard.
For the stylus there is a small block of clear plastic designed to create a friction lock to stop it falling out. There is luckily another small plastic spring lock at the far end so if the stylus is fully in it should click in and not drop out even without the plastic block. The problem is that the plastic block is not held firmly in its slot and as it gets loose creates far too much friction against the stylus which can then drag it right out.
The loose keyboards are due to the metal runners (that you see on back of keyboard partially springing apart (breaking tiny micro welds) at the ends where they lock (or not!) open and closed. These runners if they have sprung open like this will never lock firmly again unless you perform a bit of DIY.
I have performed small operations to fix both these problems and my Keyboard now locks very firmly both open and closed. The stylus issue is dealt with internally with a felt runner at a specific location. BEWARE of course performing these operations will invalidate your warranty. I can be much more specific for anyone who wishes to contact me directly particularly with the keyboard issue which requires quite a chore in dismantling the device - though I can now perform this in half an hour start to finish (Not something I'm proud of with a new device, but I had to workout just how to do the fixes!! )
Actually otherwise I think TYTN is great - superb in fact which is why I did not send it back for repair - couldn't bear to be without it!.
PS Finger around the screen method works every time for me forget all that align screen caper.
Mike
@mikechannon: Do you have high quality pictures of disassembled device where we can see the chipset references? we need to gather information on the hardware used inside the Hermes...

Need advice: broken speaker

Hi,
The speaker on the outside of my universal (the onw you hold against your ear with when the screen is on the inside) is broken.
That started as something like a bad contact (if I pressed the phone against my ear it would work, otherwise not). Now it is not working at all.
The speaker on the LCD side is working fine.
The advice I want:
I took a look at the service manual PDF I got and disassembling the phone to reach that speaker is a lot of work. I do have experience with diassembling electronic devices and even do some soldering, etc. However, my doubt is this: I have a phone which does work, but the way I like to use it to make calls does not work.
Question 1
Is it worth the trouble to diasassemble the whole device just to check if it is indeed a bad contact due to i.e. dirt? Or will I actually risk breaking something off, which will render the complete phone useless? Looking at the service manual, one needs to use a plastic tool to actually open the phone. How easy do the hinges break off?
Question 2
Has anyone had a similar problem? Was it easy to fix?
Thank you!
Cheers,
vma
you dont need to disassemble the whole phone just disassemble the screen . It isnt that hard to do, just remove all the screws from the screen . The screen casing is difficult to budge at first but once you have freed part of it open, the rest follows quite easily.
Hi,
Meanwhile I couldn't resist and opened it...
...and I found the guilty part.
It seems that the outside speaker is actually attached to the case and uses a contact connection to the PCB. This connection is made by to metal plates, which are tiny and folded. They will compensate the varying pressure made on the case (i.e. when you press it) and I guess with time they tend to break at the fold.
This happend to one of the two contacts. First I tried to fix it, but the truth is that it is so small that it is quite impossible to do anything about it. I considered soldering a small wire, but that would require to solder the other end to the pin on the PCB, which then would mean, I could no longer use a regular replacement speaker, if this one had any other fault (unless I could clean the contact again, but trying that, I could break something else, also).
This means: now I am not able to use the outside speaker anymore...
Question: where can I purchase a replacement one? Would anyone sell me one from a broken Universal (for a symbolic price - anything over 10 Euro is too much, as I would prefer to just buy a another second hand Universal)?
And as I was figuring this out, I used the occation to fix that loose stylus!
1) Open the underside case (4 screws, then open the case all around with some thin plastic).
2) Roll a little bit of celotape and place it between the case and the pin that fixes the stylus in position.
3) Try it out until it is OK.
4) Close the case and that's it!
Cheers,
vma
Hi buddy, in fact I did have the same problem that you're having some months ago, my uni fell and since then the problem just got worst, until some day a couple months ago I opened it and fix it.
It's just like you say, the little golden plated contacts wore off, then the little speaker's metal plates just were too high to make any contact against the pcb, it's really simple, just pull the plates gently away from the little speaker, do clean both sides of the contacts (pcb and speaker's plates), i did this with a little xacto knife (be very gentle), and that's it! It worked just fine.
The problem is that in my case one of the metal plates broke off.
I tried to fix that, but it is to small for me to achive anything.
Cheers,
vma

Stylus falling out of hole issue!!

I'm having a big problem with the stylus. It won't stay in the hole anymore. The second I put it in it falls out. Am I going to have to replace my whole phone? Thanks..
Turn the phone upside down. Remove the battery cover. On the left side of the battery is a plastic piece that catches the stylus. Maybe it came loose and can be glued back down.
also
Take a small piece of clear plastic tape and wrap it around the end of your stylus. It will create some width and keep the stylus in a bit more easily.
Thanks for the information. I looked at it and when I put in the stylus one end of the plastic piece keeps poping up and won't stay down. I used a piece of scotch tape to hold it down and it's working for now, but I think it's only a temporary solution and it's going to start coming loose again when the scotch tape wears out. I called the local Verizon Wireless store and they said they would replace it with a new phone without having to use my insurance, but they hardly ever keep stock on this phone in the store, so I have to keep calling to see when they have stock. Another issue is I guess I'll have to install the stock rom back into the phone before I return it. Is there step by step instructions on how to do this? Is it something that's really difficult to do? Thanks for the help and time..
Assuming the same type of layout to the TyTn then you are correct that will only be a temporary solution. The clip at the end of the stylus silo is not designed to fully grip the stylus. There should also be a rubber/plastic block further down the silo to friction grip the stylus. See pictures here from the TyTn:
http://forum.xda-developers.com/showpost.php?p=1206800&postcount=35
Mike

HD2's innards: Attempted vibration motor fix gone horribly wrong.. HELP!

I'm hoping somebody with some knowledge of the HD2's innards can help me...
My vibration stopped working on my HD2. I found the plastic LED flash cover to be 'pushed in' (with the help of a couple xda threads I dug up). Others said it was an easy fix: Open the case and push that piece of plastic back into place.
I opened up the case to correct it. But after putting it back together not only does vibrate not work, but the volume keys, speakers (both earpiece and speakerphone), flash, notification led, and camera all don't work.
I obviously screwed something up, but I have no clue what it could have been. I was very careful. One thing I'll note is that when I pulled the case apart, the plastic volume rocker went flying. When putting the phone back together I got it back into place so that I THOUGHT it should work (it was seated properly and felt "clicky" for up/down movements.
But clearly wasn't just the volume rocker that was affected. It doesn't seem that I pulled anything else loose or anything like that...
But no luck, all that I listed above is non functional, and what I'm left with is a glorified 3.5 in tablet
Any ideas?? Thanks in advance!!!
Snapped a couple quick pics which may help:
http://i50.tinypic.com/mmsa36.jpg
http://i47.tinypic.com/sl1kdx.jpg
Unfortunately when comparing these to other pictures of the inside of the HD2 that I found online, I fail to see any differences, or anything I could have inadvertently screwed up.
Most likely you screwed up(or disconnected from motherboard) somehow your main flexboard, but your picture are not usable for this, you should take off your motherboard+main flexboard from chassis to have a full view!
You probobly just disconnected a small cable. I have no idea of the HD2 innards but did multiple repairs of small stuffs and the flat cables hold in place by a plastic clicker pull out easily - just reopen and check them all, you should be fine.
Thanks for the input! I figured it's something like that, just one small cable. But I didn't even take off the board at all... The pictures show the full extent of the disassembly... Do we still think it's necessary to disassemble it further?
I checked all visible connections, but yeah, maybe I somehow yanked out something that is NOT visible. I'll try to check again today... In the meantime, any more ideas from anyone else? Thanks!
For al that to be not responding I would assume main-flex damaged or as mention before maybe connection to mainboard got moved during pulling cover !
Volume button can be troublesome, sometimes the little plastic caps come off but if it felt clicky should be good in that respect.
also be very carefull of thin spring metal legs that contact antenna pads on back cover, one near screw above & right of vibro motor looks a to be a bit flat. They bend easily & break easily too ...
Have u tried starting up the phone without the backing? I had this issue when I painted my housing the led cover was stopping the motor from spinning but if i took out the backing it works. So I just trimmed the led cover and now it works.
Mister B said:
For al that to be not responding I would assume main-flex damaged or as mention before maybe connection to mainboard got moved during pulling cover !
Volume button can be troublesome, sometimes the little plastic caps come off but if it felt clicky should be good in that respect.
also be very carefull of thin spring metal legs that contact antenna pads on back cover, one near screw above & right of vibro motor looks a to be a bit flat. They bend easily & break easily too ...
Click to expand...
Click to collapse
I'm nooby with regard to this stuff; I only attempted the repair since I read in a couple other threads about multiple self-proclaimed non-super-tech savvy people were able to open it up and move the plastic LED cover for an easy fix.
So what exactly am I looking for with regard to the main-flex? Where is it? I thought I wouldn't really see that unless I removed the board which I haven't done... is it still possible I knocked it loose or damaged it? I didn't think that would be possible since I ONLY removed the back cover (though it does take a slightly uncomfortable amount of force to do so, so I guess anything can happen...).
If not the main flex cable, is there anything else specific to look at which may be disconnected? It seems to be all the stuff at the top of the phone that fails to work (camera, speakers, vibration, flash, volume keys). While the stuff on the bottom (other hardware buttons, charging jack, headphone jack, etc).
THanks!
I have given up. After being stumped briefly how to hard reset the device without the volume keys working (I have Android installed), I was able to do it via ADB from the Android dev kit.
To ebay I go...

Categories

Resources