I'm having a big problem with the stylus. It won't stay in the hole anymore. The second I put it in it falls out. Am I going to have to replace my whole phone? Thanks..
Turn the phone upside down. Remove the battery cover. On the left side of the battery is a plastic piece that catches the stylus. Maybe it came loose and can be glued back down.
also
Take a small piece of clear plastic tape and wrap it around the end of your stylus. It will create some width and keep the stylus in a bit more easily.
Thanks for the information. I looked at it and when I put in the stylus one end of the plastic piece keeps poping up and won't stay down. I used a piece of scotch tape to hold it down and it's working for now, but I think it's only a temporary solution and it's going to start coming loose again when the scotch tape wears out. I called the local Verizon Wireless store and they said they would replace it with a new phone without having to use my insurance, but they hardly ever keep stock on this phone in the store, so I have to keep calling to see when they have stock. Another issue is I guess I'll have to install the stock rom back into the phone before I return it. Is there step by step instructions on how to do this? Is it something that's really difficult to do? Thanks for the help and time..
Assuming the same type of layout to the TyTn then you are correct that will only be a temporary solution. The clip at the end of the stylus silo is not designed to fully grip the stylus. There should also be a rubber/plastic block further down the silo to friction grip the stylus. See pictures here from the TyTn:
http://forum.xda-developers.com/showpost.php?p=1206800&postcount=35
Mike
Related
Hi!
Can anyone help me with recommendations how to remove back cover from my XDA I? I tryed to do that, but unsuccessfully . I don't want to damage this device, so I decidied to ask some advice.
Xda I case open
Just use a slot screwdriver for the top two slot screws. Then T6 for bottom two. Then unit held screen face-down ; use a plastic lolly stick with sharpend flat edge to work between front and back case. It`s best to start at the bottom right edge, near the hard reset hole.
Using a downward push action, plus, practice the case should just pop apart. Work the stick around the bottom, forcefully. Things should just workout o.k. from there.
Remove the void sticker from screw using tweezers. With care it will remain in tact, and can be replaced.
Remember to be forcefull
anyone have some more details to get into the xda ( i amtrying to replace the LCD) pictures/instructions what ever i can get will be greatly appreciated
I used a T6 torx for the bottom screws and a standard flat blade for the top, remove stylus. If you have finger nails, force your thumb nail along the groove starting near the reset hole, this will pop the tabs, you can then slide your thumb nail all the way around and remove the back. You will then need to remove 2 very small crosshead screws, one at bottom left and the ither at the top offset to the right, this is under a label "warranty void". The flat cables can be removed by bringing forward with a tiny flat screw driver, the retaining tabs, on the small ones try to bring the tabs forward towards the cable, at the same time, once you do one you will get the idea. The larger flat connecter needs the 2 retainers at the sides to be moved slightly to the sides to release the flat cable. Once this is done it is very obvious how to get the rest out. Seperating the screen from the digitizer is not so easy but it will seperate if you are diligent and careful but firm.
cruisin-thru said:
I used a T6 torx for the bottom screws and a standard flat blade for the top, remove stylus. If you have finger nails, force your thumb nail along the groove starting near the reset hole, this will pop the tabs, you can then slide your thumb nail all the way around and remove the back. You will then need to remove 2 very small crosshead screws, one at bottom left and the ither at the top offset to the right, this is under a label "warranty void". The flat cables can be removed by bringing forward with a tiny flat screw driver, the retaining tabs, on the small ones try to bring the tabs forward towards the cable, at the same time, once you do one you will get the idea. The larger flat connecter needs the 2 retainers at the sides to be moved slightly to the sides to release the flat cable. Once this is done it is very obvious how to get the rest out. Seperating the screen from the digitizer is not so easy but it will seperate if you are diligent and careful but firm.
Click to expand...
Click to collapse
thanks bud... well i dont want to mess with the digitiser if it is a pain the spare i am getting is having a prob wih sound so i will just go ahead and replace both instead of trying to seperate them... will keep u posted as soon as the other one arrives...
if anyone has more comments plz feel free to add the more the merrier and the chances of a screw up are reduced.
i will also try take pictures along the way so that someone else gains.
Broken XDA
Hi all,
can anyone help me fix my xda. A couple of weeks ago a bit of the headphone plug broke inside the connector. In an attempt to clear it I opened up the XDA. But now it doesn't power on after I've replaced the cover.
Any pointers would be much appreciated
Before you open your phone you should push the unscrewed top half of the stylus in the hole bottom right of your xda, this disconnects the battery, you need to check the flat shiny connecters on the edge of the board make sure thay havent been pulled out, the power from batter is on 2 contact pads inside rear of case so I dont think that is the problem. You could try using the stylus as mentioned as it may need switching back on.
hello to everybody!
i got my xda trion 2 weeks ago. after one week, it was impossible to bring the stylus into the xda. so i got a new one.
after again one week, the stylus wont come out of the trion.
someone else prob's with the stylus?
greetings
karl
+ 1, probleme like a wizard too
same ting happened with my TyTN today...
+1 with one week old tytn
Same here...
First I couldn't get it out / then I couldn't get it in / then it would simply slide in-and-out freely to the point that only gravity was holding it in place (sorry if this sounds dirty, but this is what happened).
Had to have mine replaced. I've heard this issue has been around since the Wizard...
I really hope I don't have the same problem on TyTn #2!!!
After a few days of having mine suddenly the stylus was becoming enromously difficult to remove. At one point it just wasnt moving so after a forceful tug it pulled out and a tiny transparent square of plastic/rubber fell out with it. Looks like it was in there to keep it in place but i have no idea how to put it back in. Now the stylus removes fine and stays in place too :shock:
I had the same problem.
Could not get the staylus in with my TyTN.
So I did the mistake and pushed it in... a "knack" sound alerted me that something bad happened. Could not get the stylus in still... so I yanked a small rubber plastic piece from the stylus hole on my TyTN. Now I can slide easily the stylus in.
From teh reports I heard my guess is that the rubebr plastic inside the TyTN is used to firmly hold the stylus in. While without this rubebr plastic there is nothing to hold the stylus until you fully place it inside the TyTN.
andmjones said:
After a few days of having mine suddenly the stylus was becoming enromously difficult to remove. At one point it just wasnt moving so after a forceful tug it pulled out and a tiny transparent square of plastic/rubber fell out with it. Looks like it was in there to keep it in place but i have no idea how to put it back in. Now the stylus removes fine and stays in place too :shock:
Click to expand...
Click to collapse
Same here TyTN 1 week old.
same here,
think I'll swap mine over for a new one.....
raptorian said:
I had the same problem.
Could not get the staylus in with my TyTN.
So I did the mistake and pushed it in... a "knack" sound alerted me that something bad happened. Could not get the stylus in still... so I yanked a small rubber plastic piece from the stylus hole on my TyTN. Now I can slide easily the stylus in.
From teh reports I heard my guess is that the rubebr plastic inside the TyTN is used to firmly hold the stylus in. While without this rubebr plastic there is nothing to hold the stylus until you fully place it inside the TyTN.
Click to expand...
Click to collapse
Same here in 5 days
happend with me after 2 weeks. I've been struggling for a week, and now it's workng again! Don't know how long it will last. I hope it won't brake down, I bought Hermes thrue internetshop. Always sick to return things.
I carry something like this, and only use the tytn stylus in emergencies. I'm hoping this will reduce wear.
Same here - less than 2 weeks.
:shock:
Same here 5 days, luckley I had a replacment on order for BT problems recived that today lets see how this one goes.
me 2
my TYTN's stylus wouldn't stay in the hole.
i sent my tytn to be replaced (due to BT problems and screen alignment)
and i hope i t won't happen again.
when i put the tytn in the box to be sent so the stylus stopped falling :? )
that is odd
My stylus is a little difficult to remove at times, so I had a look down inside the stylus hole and it appears that there are three of those little pink rubber squares protruding from the side and a dark rubber 'socket' at the end to grip the tip when it's fully inserted. The pink squares are obviously there to provide a little more grip along the length of the stylus, but my guess is that even without them the 'socket' at the end would hold the stylus in place. I imagine that over time the pink rubber will either soften up or disintegrate entirely with the friction.
Solution stylus problem
I had the same problem with my stylus, my solution is take a Poster Buddy Brand name Pritt it is so called here in Holland you can place posters and photo's with it on wals, doors etc. looks like white rubber glue, think I see it in the UK with the name Sticky here you can buy it with photostores and bookstores etc. Take a small piece of it turn it between your vingers to a small ball and put it in the stylus hole after that push it to the end with your stylus.
After I do this I have no further problem with the stylus it works great.
Same issue here... the 2nd day I had it a small transparent square rubber went out of the stylus hole. Now i can put it in and out without problems...
Loose/Jammed Stylus
I'm afraid sending device back for replacement/repair for the stylus problem and loose locking keyboard may only be a temporary fix. Having had my device dismantled I can see exactly what the problesms are with both stylus and keyboard.
For the stylus there is a small block of clear plastic designed to create a friction lock to stop it falling out. There is luckily another small plastic spring lock at the far end so if the stylus is fully in it should click in and not drop out even without the plastic block. The problem is that the plastic block is not held firmly in its slot and as it gets loose creates far too much friction against the stylus which can then drag it right out.
The loose keyboards are due to the metal runners (that you see on back of keyboard partially springing apart (breaking tiny micro welds) at the ends where they lock (or not!) open and closed. These runners if they have sprung open like this will never lock firmly again unless you perform a bit of DIY.
I have performed small operations to fix both these problems and my Keyboard now locks very firmly both open and closed. The stylus issue is dealt with internally with a felt runner at a specific location. BEWARE of course performing these operations will invalidate your warranty. I can be much more specific for anyone who wishes to contact me directly particularly with the keyboard issue which requires quite a chore in dismantling the device - though I can now perform this in half an hour start to finish (Not something I'm proud of with a new device, but I had to workout just how to do the fixes!! )
Actually otherwise I think TYTN is great - superb in fact which is why I did not send it back for repair - couldn't bear to be without it!.
PS Finger around the screen method works every time for me forget all that align screen caper.
Mike
@mikechannon: Do you have high quality pictures of disassembled device where we can see the chipset references? we need to gather information on the hardware used inside the Hermes...
Hey anyone already opened up their HD2? I need to open mine since my back button got stuck while my baby girl tried to press too hard on it. Now the back button feels like it's not presing at all compared to the other buttons.
i also have a spare housing that I am thinking of putting in.
Anyone can point me to the right direction?
Thanks
i've had the back off mine.
first search youtube for leo disassembly and you'll find an htc disassembly video: "leo Ds" (and another "leo As" for reassembly). they are somewhat daunting, but do not despair!
mine came back from a htc warranty service with a fingerprint on the inside of the lens glass and i couldn't be bothered sending it back again for cleaning so i did it myself. cracking the case isn't all that easy, or wasn't for me.
after you remove the 4 screws (get the void sticker and moisture indicator out with a pin), you still have to unclip the back from the chassis. WHY do electronics manufacturers design them like that??! in the video the tech uses a plastic hooked tool which i do not possess so i had to rely on my fingernails -- which i nearly pulled out! i tried for a good 15 minutes before it finally separated (with me sweating all the way that i was going to damage the LCD with the force i was having to apply). but it all finished happily in the end.
good luck with yours!
Not sure if it's worth it.
1st things 1st, watch the video on youtube..
.
Assuming u broke the keypad (just like me, but mine is right in the middle) at about the 6th minute of the disassembly video, they'll show u where u'd be replacing the keypad.
Removing the 'lcm and follow the indicator' isnt as simple as it look. you'd find the glue to be really tough. Putting it in an oven, sure, it'd be hot to the touch, and let it cool down a bit it'd be hard again. Hairdryer? Still too hot. Gloves?u'll lose touch sesitivity. So what i did was use a small blade/box cutter and cut which ever visible glue... and assembling, i had to replace all the double sided tape with some cheap ones...weak ones. Could be a good thing.. or a bad thing. Good, cos i know i dont have to wrestle with some really tough glue..in case i ruined my lcd again.... bad.. cos its..not that secure, i rmember that i nearly ripped it open unintentionally!
Neway replacing my digitizer+lcd took about 3 hours...had a couple of breaks, and spent 15 mins looking for the proximity sensor or was it the ambient light sense 'lense'..very tiny things those things are. So be careful...cos i eventually lost it..grrr
Anyway, Best of luck.. .now to find a replacement keypad that cost less than 5usd..hehe
dsx2b said:
1st things 1st, watch the video on youtube..
spent 15 mins looking for the proximity sensor or was it the ambient light sense 'lense'..very tiny things those things are. So be careful...cos i eventually lost it..grrr5usd..hehe
Click to expand...
Click to collapse
a good tip here is to work with the phone in a large tupperware box so that if something drops out it can't go anywhere.
note to the OP: i've read several posts where people damaged the ribbon cable connecting the bottom buttons to the mainboard so be careful. it looks very delicate.
Having just opened mine up several times recently I can offer a couple of tips.
1. Unscrew the four screws - they are T5 torx size.
2. Use thin stiff plastic pieces (I found the plastic case that nails are sold in to be the right stiffness and thickness). Cut some up and push them between the case and the phone works so that they hold each of the locking tabs out in turn. I used five or six bits to do this. Three on the vol control side, two at the top and one on the top area of the other side.
3. Then pushing out at the top where the battery would sit while prying with finger nails outward on the long vol control side you can work each of the locking tabs out so the plastic bits hold them unlocked. Do this along that side, across the top and down the other side working each one a little bit as you go and repeat.
4. This should allow the top edge to come out allowing you to lift is out and "up" so that the button end slides out.
This worked very well for me..several times.
The display is held to the electronics portion by double sided tape and yes it is very strong. But you can soften the adhesion significantly using a heat gun. But you must be careful to heat the whole area to avoid thermal differences cracking the screen. The heat will loosen the tapes grip allowing you to pry the screen away from the electronics side.
Note that the screen is made up of the LCD covered by the glued on digitizer and they are connected with a single ribbon cable on the lower right hand side (I think from memory). This means the screen has to lift off with a hinge action. Lifting along the opposite long edge to the ribbon cable, rather than lift from the top or bottom.
Hope this helps.
Hi, I tried to open mine and followeed the video, be careful as the video makes it look much easier than what it really is, I ended up ruining my device, just take your time and do it slowly.
Thanks guys! Gonna try it over the weekend. Worst case is that I break my case or put some cosmetic damage. I have a spare case though hehe.
The problem about the key is the back button feels stuck.... the other buttons are snappy and have a tactile sort of feel, where as the back button doesn't have the same feel. looks like it was pressed to hard and never popped back up...
just annoying when i've been very careful with the phone.
ok looks like i wouldn't have to open my phone.... i tried to but then there's a warranty void sticker, so I just called tmobile and explained about the back key being stuck.... and they're sending me a replacement.
i'm gonna lose my invisible shield full body though... but better than risking breaking my phone....
Hello all. Yes I am a noob to the forum, but not to small electronics and the dismantling of them. After getting everything set up on my machine necessary to Root my TF and side load the netflix app, I noticed my power button wasn't being as responsive as it should. Doing a quick google search I found that this was a common thing, even on TFs with stock firmware, so I took to dismantling the thing to figure out what is causing it.
I did a quick search to see if anyone has cracked the case open and found this thread. I didn't use a guitar pick, but rather a plastic and metal spuder set I had from repairing my mom's ipod touch (damn soldered batteries!).
Tools:
Tool Kit
Or
A T5 Torx bit
A spudger
#0 Phillips screwdriver.
Lock-Tite super glue gel (optional!)
1. Start by removing the two T5 torx bits from both sides of the charging/dock port
2. Use the plastic spudger or guitar pick and loose the seam around the entire case. If you look closely at the face, you will see the glass meet a black plastic rim and then the metal rim around that. What you are aiming to do is separate the black plastic from the glass. The plastic is glued to the metal so if you see adhesive separating, you are prying the wrong spot. There are various plastic tabs around the glass like a TV remote so using the plastic spuder is safer until you get some visible room to go in with the metal one.
3. Once you have the frame off, there are 4 #0 Phillips screws on the face, one at each corner, then 3 screws on the top and bottom of the frame (previously under the metal case
4. Removing all 4 face screws plus 6 rail screws will allow you to remove the back plastic. Now you can see everything
5. Bonus points for ASUS for giving us a battery that unplugs vs one that is soldered in (damn you apple). If you want some peace of mind, you can pop off the battery cable. I did not see any side effects from doing this (no data loss, etc).
6. On the side with the power and volume buttons, you will see a blue-tipped silver cable under a black tab. This black tab is what holds the ribbon down and lifts up like a toilet seat. It does not pull forward, it does not pop off (unless you broke it), but because it is plastic, be gentle. Once the tab is lifted, the silver cable will come out.
7. Unscrew the 3 #0 Phillip screws holding down the button board for easier access remove it.
-----
It doesn't matter whether you are having a volume issue or power button issue, so long as you know its hardware related. The way these buttons work is under constant pressure is "off" and removing that pressure turns it "on". So the metal tab pushes down on the plastic button, which pushes down on the switch. What is happening is over time, that metal tab gives way to less pressure on the daisy chain and the button stops working. The good news is, this metal tab is just held on via 'wings' around the soldered base. A razer knife is enough to gently lift the wings to pop the assembly apart for repairing. Given the construction of these switches, I wish ASUS just made the entire board available, but oh well.
-----
8. With the offending metal cap off, bend the middle thumb further down and back in to position and re-assemble the switch.
9. (Optional). I bent my tab further in to prevent me from having to re-do this operation several months from now, but doing so meant that ANY pressure on the button caused the metal cap to pop back off. That is really bad if the case is re-assembled. My solution was to swab some lock-tite super glue gel on the bottom wings and base of the metal cap and put it back on the switch. A very thin film is sufficient because it is a gel, it dries in seconds. WARNING> Once you reassemble the switch, keep pressure on the metal cap while you keep pressing the black button. If you don't, any glue leakage will lock that button in place.
Alright, I didn't make this fix, but I don't remember who did, but it was someone in a youtube comment. Before attempting this, are you sure your charger isn't just dirty? If it is dirty, it's preventing the rubber o-ring from getting a good seal. Take a piece of tape that won't leave a residue, and take off as much dirt as you can. If it still slips, try this fix. Okay, so the fix goes like this:
1. Turn your charging orb upside down. There should be a rubber ring on the bottom that prevents the orb from slipping, and it puts it at an angle. Remove it, but don't throw it out, and try to keep the adhesive intact.
2. There should be two small black tabs on the rubber ring. Cut these off with an exacto knife or a similar tool.
3. Turn the ring 180 degrees from where it was before, and carefully apply the ring, making sure there are no bends or bubbles in the ring.. This way the thicker end should be facing the front, makes the angle a bit less obtuse.
4. Give your nexus 4 a good wipe, so there's no dirt on that, and put it on your charger. It shouldn't slip anymore! I hope that this helped you. It did for me!