Bluetooth headset and time - 8125, K-JAM, P4300, MDA Vario General

Hi. I was wondering if there was a program that can link to the Bluetooth headset to give the time. I don't have Voicedialer or MS Voice Command. It seems that the headset can do voice dial with the current voice recognition for my 8125. I was wondering if there was a program or a way to state "Time" and have it give the time. Or perhaps instead of the beep that precedes giving the voice entry could be changed to give the time.
(I'm not much into wearing watches and have used my phone as a watch. However, pulling out the 8125 isn't as easy as my old flip phone).

Related

Possible Solution for Voice Command and Non Working Headsets

Hi,
I'm no developer so I don't know if this would work but if there is a developer out there with spare time and knowledge of the Bluetooth Stack, maybe they can confirm if this is possible and even write something.
Headsets like the Motorla H700 and the Jabra J10 seem to lose the ability to activate Microsofts Voice Command after the first call. I notice that if I run Cyberon's Speed Dial after this happens, Voice Command activates when the headset button is pushed.
Cyberon's Speed Dial is obviously resetting the connection or something. So wouldn't it be possible to write a small wrapper that would reset the connection to the headset and then launch Voice Command. This utility could be set in the registry for Voice Dialing and it would reset and launch Voice Command.
If this works it would make a lot more bluetooth headsets useable with Voice Command.
Just a thought (as dumb as it may be
Hi,
Search the forum..there is a solution with A2dp and the compatible BT headsets.
I searched didn't see it, if there is a solution, can someone point me to the solution or thread.

MS Voice Command still does not work through Bluetooth

I changed the path to voice command in the registry (HKLM/Software/OEM/VoiceCommand/ Path=\Program Files\VoiceCommand\voicecmd.exe), but my Cardo Scala-500 headset still does not activate Voice Command. I searched extensively, was not able to find how to make them talk to each other. Any ideas? Anybody else using MDA+Scala-500 combination with Voice Command successfully? I am on the last official T-mobile ROM.
I don't know if it is anything related. When I first paired my Wizard with a Motorola Bluetooth, the pairing process says it is hands free device. However, it will not do voice dial. Then I tap long on the selection of this device in Bluetooth configuration and bring up the menu. In the menu, I select make this device the default hands free. Afterwards, it will work with voice dial.
You need to check to see if that headset supports voice dialing. I beleive that there are some out there that don't.
The "Hands Free" checkbox is checked on the device. And the manufacturer says it does support voice dialing. Anecdotal evidence (online search) also says that some people were able to use MDA with this headset and MS Voice Command.
Can it be a function of my ROM or any radio versions? They are in my signature if it matters.
Also, the headset has "Bluetooth version: 1.2 Class2". I do not know what that means, maybe that is why I think it may matter.
Different headsets behave in wildly different ways when it comes to activating voice dialing. My Moto HS850, for example, activates VC on the second push of the button, and you can tell at the same time it is pulling all sounds from the phone so you can hear the "bling-bling"... and then it takes its sweet long time in allowing the phone to return to normal so you cannot use VC again until that happens. My Bluespoon AX2 is different, in that it works every other time, and my Jabra BT800 just plain doesn't even work.
I suggest you play around with the BT config in your phone to see what works best for you.
I tried one click, double-click, tripple, and push-and-hold - nothing works.
Also, just tried a colleague's headset (Jabra JX10), it does not activate Voice Command on my Wizard either. I am going to talk to the manufacturer of my headset, see what they say.

8525 and Voice Dial with Headset Problems

I have been using the voice dial option on my Cingular 8525 without any problem since day #1 and it is great, especially after downloading that file on XDA that allow me to reprogram the 5th pushbutton for voice dial.
I also admit that i am knew to the headset arena, having just purchased, for voice dial and incoming calls, the 'Jawbone' device, which was highly rated on CNET and PCWorld.
It doesn't work. What I mean is it rings and I can answer phone calls and it sounds OK, but when I go to voice dial out, the phone either gives me a message that it didn't understand my request or I get a wrong phone number. Failure rate on voice dial is 98%.
The manual says to rerecord the voice tag with the Jawbone on, for maximum effectiveness. so i turned it on, put it on, went to voice dial and just re-recorded the voice tags, still with 98% failure.
So, is this how it is with the 8525 and ALL headsets or do I return and try a different headset? Are there tricks to get this working? If I could just get 10 numbers to work, that would be 75% of my calls. Thanks.
Doesn't anyone use a headset with their 8525?
I hope someone posts an answer...please.....
I've been using a Southwing SH310 Bluetooth headset with my Cingular 8525 and Custel's WM 6 for several months now without probs; position can sometimes be tricky for VoiceDial and/or Voice Commander to work well, but once in the correct position it's good. I have found, however, that Bluetooth devices, especially the high end ones that are particularly sensitive, can have problems with external noise, i.e. wind and car noise when driving, etc.

Use bluetooth headset to record voice notes?

Is it possible to get my Cingular 8125 to be able to record voice notes using the microphone in my bluetooth headset instead of the built-in mic ---- without killing the voice dialing feature at the same time?
Still using original not-unlocked 8125. (*Just found this place, havn't been brave enough to start messin' with roms. I'm sure it will come in time )

Is using MS voice command through BT hands free possible?

I've done some searches and not found anybody who manages to use MS voice command through a hands free headset.
I've just bought a parrot bluetooth hands free for my car. I'd hoped to be able to use MS voice command for voice dialing. I get the actual phone call through the hands free, but the voice prompts for VC come through the phone and the mic on the phone is used for voice recognition.
I've read people hacking about to get all audio through the hands free, but the hack I've seen disables VC.
Does anyone know if it's possible? Or is there any other software that can be used for voice dialing through the hands free. I'm guessing not if it's htc bad implementation of the bluetooth stack.
Cheers
it is definitely possible - if with BT handsfree you mean bluetooth headsets. With my Jabra BT620s i could use MS voice commander 1.6 and give instructions....it ALMOST works, in the sense that it technically does the job but, at the end, i didn't like it: too sensitive to noise and to....my english....
andrewpmoore said:
I've done some searches and not found anybody who manages to use MS voice command through a hands free headset.
I've just bought a parrot bluetooth hands free for my car. I'd hoped to be able to use MS voice command for voice dialing. I get the actual phone call through the hands free, but the voice prompts for VC come through the phone and the mic on the phone is used for voice recognition.
I've read people hacking about to get all audio through the hands free, but the hack I've seen disables VC.
Does anyone know if it's possible? Or is there any other software that can be used for voice dialing through the hands free. I'm guessing not if it's htc bad implementation of the bluetooth stack.
Cheers
Click to expand...
Click to collapse
I have the same problem - has anyone found a fix?
Incoming calls are fine, also connections that are made after the initial user-to-phone command.
I also have a diamond and this operates just fine ie the MSVC prompt comes through the bluetooth OK.
Thanks
PS yes, I have tried changing HKLM\Software\Microsoft\Bluetooth\AudioGateway
BTAGExtModule =vcbthag.dll to BTAGExt.dll

Categories

Resources