Database Users

GPS and TomTom5 Problems

I recently purchased a bluetooth GPS receiver (branded as Fusion with X70 as the name on the back - purchsed from Polstar) and TomTom5 software but cannot get the two to work together.
I have bonded the receiver and set it as COM7 and I can choose that in TomTom5 as the COM port to use but it always says "No GPS Device!"
I have also downloaded and installed the BlueTooth Tools software but this hasn't helped either.
I have an o2 XDA2 and any help with this would be much appreciated.

I think mine is set to BT on com6. You must make sure the GPS receiver has a satellite signal before you try to configure tomtom (flashing light or whatever). Keep trying different settings, that's what I did

I think I have tried all the settings I can, I am beginning to wonder if i've got the correct version of TomTom5 installed! My device information says my platform is PocketPC and that is the version of TomTom5 I installed.
I have tried various settings and soft-rebooted my phone in the meantime after each change and tried without re-setting too!
This is getting rather annoying now

sorry, I'm using com5. Have you made sure you've got a satellite connection first.
Mine is version 5.000

When I turn on my GPS receiver I get two lights flashing, one to indicate that the bluetooth is sending a signal and the other to say that the device is receiving a GPS signal.

Try this...
Hi Dave,
Did you buy this via eBay? Couple of friends have bought from the same guy and neither worked, even though it seemed that they were (flashing lights, bonded etc). Both Polstar/Fuzion.
Anyway, if it won't connect via 'other bluetooth', try selecting 'other cabled device' and then select 4800 baud and your bluetooth com port.
Don't know why, but have had to do this with 3 different PDA's so far (2 XDA, 1 ipaq). It seems to work fine, although the data rate's a bit slow.

Any bluetooth gps I have has installed as com 5 when bonding, it asks if you wish to install serial profile and allocates com 5. I have noticed however that tomtom is very weird with its gps module, it keeps saying gps not found or signal lost etc and then I have to reselect other bluetooth and com 5 and even then sometimes I have to reinitialize the receiver before it is found. I always advocate the use of a wired gps if it is only required for vehicle use, it is less problematic, easy to configure and works 99.999999% of the time without problems.

If you run BT Manager and then check settings, it generally sets up as inbound com5 outbound com 6.
I have a Navman that behaved perfectly on Com 5 on TT3, on TT5 still behaves perfectly, but now uses Com 8 instead.
No idea why, don't really care that much -- it works.

I did buy the items from eBay and I am going to get back to the supplier (Polstar I believe) to see what I can fathom out.
Many thanks for all your advice, I have tried all options but still cannot get it to work so I will post a reply with the solution that works for me and hopefully it will work for others too.

No signal
Hi
the TomTom 5 has a new implementation, from the the TT3. It can manage the bluetooth connection. When you creat the connection with your pocket pc, by serial port, you must creat one connection of paired devices, as you created to your headset, bluethoot, of course. By the way, usually tt5 uses com 6 to connect with gps receivers.
The first time you configure your connection you must stay in position to receive signal from satelites, because its important to record all information from your gps receiver.
Regards

With regards to that marcusmodestus I think tonight, I will try and remove TomTom5 and delete my connection to the receiver and try installing again, from fresh.
Should I bond my reciever before or after I install? And should I run TomTom5 only with the bond in place?

bt gps
I bought one of these
set up as other cable on com5 but set baud rate at 38400 works fine 4 me

Success!
First, thank you all for helping me with this!
I have managed to successfully set it up now and here is the process...
Install TomTom5
Bond the device (I only had the option of Serial COM 7)
In TomTom5, change the preferences to use "Other Cable" and set the baud rate to 4800.
Magically I then get 5-6 satellites, a signal and an annoying American (which I will change to a nice english lady)
Thank you all again!

after hours of trial and error with tomtom5 and buzzmobile5.0 together with a xaiox wonde-xl bluetooth gps mouse (nemerix chipset) i learned the following:
it is recommended that you disable the gps manager of buzzmobile5.0 (not doing this has caused my device hang and auto soft reset some times). after that the following procedure worked for me:
1. pair your bluetooth gps device with your xda
2. assign a free outgoing com-port to that device (what com-port is best? please read text below.)
3. go to tomtom gps settings screen choose other bluetooth gps device
4. the assigned com-port number should appear in the next tomtom screen.
usually you should be done now and the connection should work, but i always had to delete the gps device in buzzmobiles bluetooth connection manager and had to re-pair it again, re-assign the com-port and re-start tomtom in order to get it work.
for any reason i then choosed to assign com8 as com-port for my gps mouse. and from this moment on tomtom5 was able to re-establish connections after switching of and on the gps or after switching xda on and off. i don't know what the exact reason is but choosing com8 was my solution to get tomtom5 working together with my gps on a comfortable way.
hope this helps others
regards
peter

I had this problem with Tomtom 5. No matter what I did it wouldn't work with my receiver.
I found that when I downloaded the 5.1 patch and installed it it worked fine with the GPS receiver set to COM6. Usually takes about 30 secs for the receiver to be found though. I think the update sorted out the Tomtom bluetooth support to a later version.

hi ...
how can i disable the gps manager of buzzmobile5.0?
thx mtc

settings --> system --> GPS
On the access tab uncheck the box
btw : I just saw that GPS hardware port shows com5 now. I'm sure I set both hard and software port to none cause somebody adviced this.
Anyway last week I didn't have to re-pair my gps in order for tomtom to find it ( which before I had to do every time I closed tt5). I've been messing in the registry to create extra com5 ports, maybe that's what caused it.
Anyways I now only have to switch on the gps and fire up tomtom and it immediately shows my position. Hope it will last..........

Tom Tom XDA problem

Hi all,
Just go the xda through work, and even though i have got the new version of tom tom of their website (5.2) for ppc, when loaded and docked in my cradle, it cant sem to get the GPS to receive!?!?! anyone else had this problem?

I have an O2 XDA Exec and its working fine with the TomTom 5.2 software. I got some very useful info from http://www.pocketgps.co.uk/modules.php?name=Forums&file=viewforum&f=6 ..... basically a post on there advised setting up an outgoing com port to the BT GPS device (I used Com0) ... this is found under Start>Settings>Connections>Bluetooth>ComPorts (after you have paired the BT device of course).
In TomTom you then select "Other Bluetooth GPS" in the GPS options screen, select the Com port set previously, and away you go.
I hope this helps

I bought a 32-channel QStarz GPS receiver from eBay, cracking little thing it is. I had problems getting it going though initially - what I had to do was setup a pairing, which was a little tricky as TT didn't want to behave.
Basically, TT tries to establish a serial connection whenever I open it. As TT loaded, just before it went into the TT interface, It showed a dialog box with all my serial connections in - I think it might've been the device pairing screen, but I've not been able to find it again... What I did was pick the gps receiver's serial port device entry I'd previously set up, select it, check the box to tell TT to always connect to this device by default, and then hit enter - all before TT managed to load into the interface. It took me a couple of goes, and I'm sure there's an easier way to do this (I don't think I was even supposed to see this dialog screen ) but now it works perfectly. I don't have to establish the Bluetooth connection to the GPS receiver, TT does that (and it'll even turn the Bluetooth on and off if it's not already on for me). However, I did have to choose Other NMEA GPS from the device options, and then tweak my COM port settings (I found a scant piece of information regardingthe fact that it should be something like COM5 for incoming data and COM6 for outgoing data, you would do well to doublecheck the TomTom site's FAQs for this info). There's a couple of seconds lag whilst TT correctly detects the device and begins to latch onto GPS sats (it says "No Compatible GPS Device Detected!", and then changes to something like "No GPS Signal Detected"... And then starts picking up sats.
This is all with TT5.0, by the way.

This document will be very useful.. principal is the same for most GPS Receivers..
http://www.parrot.biz/ressources/CK3400_Help_Files/Imate JASJAR - TOMTOM Mobile 5 - 2.01.pdf

Not sure if you are trying to receive through a Bluetooth GPS receiver - if you are, this worked for me (first poston the page);
http://forum.xda-developers.com/vie...ostorder=asc&highlight=tomtom+5+gps&start=100

Thanks for your help guys, but i meat to say i am using a wired GPS the small square official Tom Tom one, hard wired in to my cradle.
I can open the software and everything, but it just says, cant find GPS, the green light flashes on my GPS, but thats all it does.
Help!

Ok, so you're using a wired receiver.. That helps to know. You should be able to choose TomTom Wired GPS or Other Wired GPS, and it should just... work. If it doesn't, choose the nearest chocie to your receiver, and go into the Advanced settings (if the option button is available) - if so, doublecheck what your COM port settings are.

Where did you buy the cradel from, I just got ripped off to the tune of £48 off ebay due to the cradle not actually passing the srl connection through, all it does is provide power for a Bluetooth GPS Receiver out of the port on the side.

I think I've heard othe rpeople saying that wired GPS receivers will not work with the Universal. Can anyone confirm this?

What you have heard is correct the mini USB on the Exec WILL NOT accept a GPS connection, you need a bluetooth device for this to work - Mike

Tony B - that sounds like the cradle i am using - jasjar or jamjar something like that!
I have put my wired GPS straight in to the side, and nothing!!
think you might have got it mate!

hi there
i am using the wired gps with mda pro tomotm car cradle
tomtom software working like i can start the tomotm and see the setting etc
now when i connect the tomtom wired gps via rj11 in cradle but i can not recieve gps signal
device says "no gps device"
please help
Regrads
Gugi

GPS in settings, tomtom problem

I am trying to set up tomtom 5.21 with my BTGPS74 receiver but cant get the two to communicate. I know there is some settings you can change in settings/system/gps but the problem I have is I dont have the gps option in settings anywhere. Am I missing something? Does any on know what I should do. Tomtom wants me to use port 3 or 7 but when I try to set them in bluetooth settings it says its not possible check your settings. Any suggestions would b welcome. Thanks.
P.S I know the receiver works as it still works well with my N70.

...you should've gotten a GPS icon if software GPS recognized.
In rgister you can force simulation.
hklm\controlpanel\gps]
delete redirect and add 'group' with dword=2
Then GPS icon will appear.
I gave it programport 7,hardware 6, baudrate=57600
gps auto checked
I'm not sure about the settings...

I had to create incomming and outgoing com ports on my 3100 (not sure if you need both)??
TomTom used com port 9 and works like a dream
as soon as you start the programme it connects automatically as long as my receiver is on.
It even connects when the BT on the 3100 is turned off - it starts the BT automaticlally when tomtom runs!

Yeah i agree all you need to do is set up the com ports, then fire up tomtom and select the com port you just set up and away it goes
Chris

Thanks for the replies guys. I know I have to set the com ports but the problem I have is there is nowhere for me to do this. For some reason the gps settings is missing from the system/settings. I am going to try to reinstall tomtom to see if it helps. Tomtom has ports 3 and 7 showing but they seem to be taken by something else so I cant configure my receiver on either of them.

I have a slightly different problem... my TyTn can connect to the BT GPS reciever, but as soon as TomTom tries to calculate a route, or I click the GPS signal icon it crashes back to the Today screen...
I've got TomTom installed with 5.21 update, anyone had any problems like this?

you just need to pair your bluetooth device go to settings connections and bluetooth and add new device, let your tytn search and it will find a new device when you have paired it select new comm port outgoing
I have no gps setting in control panel either
Cheers
Chris

Hi,
i have a strange problem with my BT. I cant create a incoming or outgoing BT port. I dont know why but it wont let me create any ports.
Anyone with the same odd problem?

I had a similar problem, Tytn would only let me choose COM0 (Zero) as outgoing port, and TT works fine with it. However, I would like to add Mapking for Asia, and this navi soft will not accept a GPS on COM0. Anybody understands why Tytn is only offering COM0 as outgoing ports for GPS?

I have set the com4 as outgoing port and now tomtom seems to work fine.

thanks for that info.
I don't know why only port 0 and all other ports are blocked but TT works for me now. I only need to wait for a better ROM and i can leave my Wizard home

I have written to a good contact at HTC since I need COM ports other than 0 for Asian Mapking navi soft (in add. to TT) . Will keep you posted.

Answer from HTC:
"As my testing, the Outgoing port is not limited with COM0. PaPaGo can accept with COM0, COM2, COM4, COM8, and COM9. I think the limitation of COM0 is the software limitation of TOMTOM, So if the user wants to use Mapking that only support COM1~7, he need delete the outgoing port COM0, and reassign another COM port for the BT GPS."
I imagine the problem lies between the Tytn and TomTom only, and other navi soft would find other COM ports. But I am kind of hesitant to interfere with a working TomTom, and go through the outgoing COM port game again...

I'm using Navigon and set up an outgoing Connection on com2 and it works fine for me.
sounds like TT is the problem ...
greetz
sphings

Guys, let me try to help you a little bit, as I work in navigation software development (Destinator).
1. The COM ports has nothing to do with the actual software you are running. This is pre-defined in the ROM you are using. That is also the reason why we see variations here - we use different ROMs.
2. In order of enabling a COM port, you do NOT need to discover the GPS icon on the settings. It is quite useless unless you wish to work simultaniusly with more than one software.
3. To enable a COM port, after you pair the GPS, look down for the tab COM Ports in the BT settings Manager. You only need to create Outgoing COM.
4. Strange but usually you will only be able to choose between 2 COM ports. The rest are hidden by the OS. MAKE SURE that you disabled the "Secure Connections". Default key for all the GPS receivers is "0000" and for Globalsat 308 is "2003". The last is AKA HP GPS.
5. If you cannot enable any other COM port than COM0, this is a ROM problem and you should contact your ROM provider like the mobile carrier. You can also try to enable other COM ports with the attached CAB file. Simply run it, it will expose all COM ports for you and now you should start trying. I reccomend to test COMs 4-8 first, normally, it will solve your problems. (Note: I got this file previously here and did not create it myself).

There have been may posts about TomTom not recognising B GPS's.
One solution that doesnlt seem to be mentioned here id to ensure that the name of the GPs in BT connections actually ends in "GPS"..
If it doesn;t renove the pairing and re-pari , but change the name this time to something that ends in "GPS"...
good luck
Charlie Grillo

Thanks guys, found another solution that works for me now:
1) Set your Bluetooth GPS to another COM port than 0 (TomTom´s standard port 6 was not available, so I choose 2)
2) open Programs/Navigator/navigator.cfg with a text editor, change COM0 to COM2
3) start TomTom - working on COM 2!
Started Mapking, found COM 2 - working now.

hello fellas,
as you can see im new here. im thinking of buying the TYTN, a sector which i have never explored before (pda sector).
it sounds great with the applications and due to my work, a need for a pda is becoming bigger.
i posted in this message due to the GPS topic.
i got a very stupid question which you may recieve occasionally if i buy the tytn.. :twisted:
why do a person need BT enabled GPS? i read you can connect it to your PDA but for what reason?
thanks in advance and apologies for any inconvience..

@D_G - welcome to this board
In order to run navigation software on your Tytn you need a external GPS connected to it. Easiest solution is a external GPS connected via Bluetooth.
Another solution would be to buy a PDA phone with a GPS receiver on board, for example the ETen G500.
Of course we would all be interested in a UMTS PDA with integrated GPS, with acceptable battery life, but that will take some time...

thanks lucas for the answer. but why would you need a navigation software if you have a GPS device? in either case you will need to have both devices in a particula blue tooth range. right?
this means you will need your handheld device + the GPS to activate the navigation software, or dd I miss something?!

TYTN TomTom Bluetooth GPS

Got my htc tytn loaded totom 5 onto it and guess what bluetooth gps doesn't work with it! Cannot get correct comm port .According to HTC TomTom know about this. Just hoping somebody already has a fix for this?

Had no problems pairing my BT Slim GPS with my Vario II, TomTom runs fine.
What GPS receiver you using ?

works fine on my xda trion as well.......im using tom tom 5.21 with BT-338 gps receiver.......im also using com port 0......you basically have to pair it and then add outgoing port as com port 0.....and during the installation on tom tom make sure you choose com port 0......that worked for me anyways....hope that helps.

Bluetooth GPS HTC TYTN
Thanks guys have re-installed tomtom and now it comes up with com prt 0.Probably didn't install correctly first time .Now up and running .Fantastic!!!!

I could cry
Hi everyone - I am having a similar problem
I have a new GPS receiver and have established a bluetooth partnership and done the outgoing port to com0 which is the default.
Tom Tom is installed and when I try and configure it I am not seeing all the options shown on the website. It just says no gps detected or something similar. I am sure its something simple.
Can anyone help please?

mobilecat said:
Hi everyone - I am having a similar problem
I have a new GPS receiver and have established a bluetooth partnership and done the outgoing port to com0 which is the default.
Tom Tom is installed and when I try and configure it I am not seeing all the options shown on the website. It just says no gps detected or something similar. I am sure its something simple.
Can anyone help please?
Click to expand...
Click to collapse
There's a program CreatePorts that is floating around (you'll have to do a search) that allows TomTom to see additional com ports in the Bluetooth GPS setup. I used this same program on my Samsung i730, and now on the 8525.
You just paid your GPS with the PPC, create the outbound port (in my case I used com 2), run CreatePorts, and then go in to TomTom GPS setup.
Once you get it set up, you don't have to run the app anymore, and TomTom works great

OUCH
dew.man said:
There's a program CreatePorts that is floating around (you'll have to do a search) that allows TomTom to see additional com ports in the Bluetooth GPS setup. I used this same program on my Samsung i730, and now on the 8525.
You just paid your GPS with the PPC, create the outbound port (in my case I used com 2), run CreatePorts, and then go in to TomTom GPS setup.
Once you get it set up, you don't have to run the app anymore, and TomTom works great
Click to expand...
Click to collapse
I tried running this but i can still only assign certain points from my bluetooth manager and dont have these displayed on the tomtom menu.

When you go into the GPS Status settings on Tomtom and tap configure, have you tried looking to see which com ports it lists and then going back to the bluetooth settings and doing trial and error to allocate any of those port numbers as an outgoing port for your GPS unit?
For my genuine Tomtom GPS unit, I did not even have to set up a port, I just had to pair the device but when I used a friends alternative brand of GPS unit for a short while, I was only able to get that one working under Com port 4. I can't quite remember but it may even have been a case that Com 4 only became visible in the Tomtom GPS configure menu after I had allocated it as an outgoing port for the GPS device (sorry, it is a while back so I can't quite remember the order in which I set it up)
Hope you get it sorted

arghh
I a so annoyed. I did this and had no luck. Later on I did something and got the option for port 2 and used it and it was great. I had to do a soft reset for something else and I cant do it again. tried everything.

MMMM
Happy yet frustrated
I have deleted create ports from my device as it only works once. I have reset my device. I reinstalled createports and extracted the file. I then saw port 2 straight away - the one that had been missing in tomtom.
The only problem is that if I do a soft reset I have to do that again!

It is very frustrating trying to get some of these things working. Have you thought about upgrading to Tomtom 6? you may find you have less problems getting the pairing and ports working right.
Failing that, I am sure you will be able to get it working again, just keep trying all the com ports one by one until you find one that appears in the Tomtom configuration. Like I said, on my XDA Vario II (Hermes) I managed to get it working on Com 4 and when I had an XDA Mini S (Wizard) I seem to remember that it was either Com 6 or Com 7 which worked on that one.
You might want to check the bluetooth settings for security and beam as well. Try turning security off (ie. passkey required off) and make sure the beam setting is ticked to receive all incoming beams.
I will keep my fingers crossed for you

download co-pilot for uk
Dashley said:
Got my htc tytn loaded totom 5 onto it and guess what bluetooth gps doesn't work with it! Cannot get correct comm port .According to HTC TomTom know about this. Just hoping somebody already has a fix for this?
Click to expand...
Click to collapse
Any one got the co-pilot softwear to insallate for MDA VARIO 2.

download co-pilot softwear for UK.
Any one got the co-pilot softwear to insallate for MDA VARIO 2.

another thread
I have just seen another thread about XDA with a patch for this that seems to work. Can someone merge the threads?

Createports
Can anyone point me in the right direction to find this program. I think that it is hidden on the web somewhere near the holy grail.

Help with TT6 + TYTN + Royaltek 2110 please
I have a TYTN and a GPS Royaltek 2110. I have position com0 and other programs GPS work correctly. The problem is that the TT6 always shows he himself message “GPS nonfound”, although always I can say to him that this in the COM0 but does not find satellite.
That I can do? I put the TT5
somebody it has the CreatePorts program and it can put it?
Thanks

try this thread:-
http://forum.xda-developers.com/showthread.php?t=288865

Pairing TOMTOM 6 with Bluetooth GPS
For all of you that are having problems pairing your GPS Bluetooth receiver with your Hermes see the instruction set below:
#Hermes can not be in flight Mode#
1st: Run BTHTools1100.exe
--------------------------------------------------------------------------------------------------
2nd:
Pair them in Bluetooth Manager
Set:
Holux (outgoing port com4)
Incoming Port (com8)
no security
------------------------------------------------
3rd:
In settings >> Connections >> GPS
Programs set GPS program port to Com 8
Hardware set GPS hardware port to Com 4
baud rate 4800
If GPS program is not seen in settings\Connections
Use resco registry or other program and:
Go to Hkey_local_Machine\ControlPanel\GPS settings\ creat (make new) "Group" with Dword data =2
---------------------------------------------------------------------------------------------------
In TomTom chose:
Bluetooth GPS
Com4
should be working Now

Pairing TOMTOM 6 with Bluetooth GPS (easy) - Kaiser
First after reading the posts I thought I had to reinstall Tom Tom or install another software. Luckily, I paused and read the message when I was about to configure my other bluetooth receiver. It said, first you must establish your bluetooth connection. Well, I lied coz I did try to go on and couldnt find COM 0 or whatever you guys have said.
But that's what I did, eventually. Paired the device as BT GPS, check the serial connection (not sure if secure connection needs to be checked but I left it unchecked to find out later). After that go to com port tab, and click add new port ie selected COM0.
Then go back to TT6 (restarted in my case), and to other bluetooth gps receiver then found COM 0 in there. Voila!!
Chose COM0, but still got no gps device message. Waited for about 2 mins while reading further into the posts and now my TT6 is working.
You could call that strike of luck I dont really care but yeah.. saving some batt power on my kaiser for the bank holiday;s trip. Have a great one everyone!!
P/s: Mine is O2 stellar on Dutty's great work.

Com 4 is the only one that works with Schaps 3.54

Bluetooth GPS Woes

Hi,
I seem to be having a problem with GPS bluetooth related connections with my Dopod 838 Pro.
Ive paired my Globalsat BT338 receiver and setup an outgoing serial port on my Dopod, and I can use Destinator 6 and TomTom 6 fine (for the time being).
The next day/time when I try to start the GPS applications, both programs report that they cant find the GPS signal/receiver even though its been correctly configured to work previously.
I then have to enter the Bluetooth settings to change and assign another outgoing serial port and reconfigure the GPS applications to the new serial port to work.
The programs and the GPS receiver worked fine with my old iPAQ hx4700 so its not a receiver or program issue.
I'm at my wits end and would appreciate any info on solving this problem.
Thanks in advance.

Delete / unpair your GPS
Make a new pair, and when you assign an outgoing COM port, use a NON secure COM port.
(Deselect the checkbox)
This should work

Rik_053 said:
Delete / unpair your GPS
Make a new pair, and when you assign an outgoing COM port, use a NON secure COM port.
(Deselect the checkbox)
This should work
Click to expand...
Click to collapse
Hi,
Ive been through this unpair / pair scenario more than a few times and Ive never used a secure com port connection.

try destinator PN 6
also make sure you pair BEFORE starting Destinator PN; I spent a whole two days before I Got this to work ... then once it worked .. the answer was actually quite logical
sorry cant remember how i did it as it was months ago when I got and paired my tytn; now I use destinator pn 6

njay22 said:
try destinator PN 6
also make sure you pair BEFORE starting Destinator PN; I spent a whole two days before I Got this to work ... then once it worked .. the answer was actually quite logical
sorry cant remember how i did it as it was months ago when I got and paired my tytn; now I use destinator pn 6
Click to expand...
Click to collapse
Hi,
The pairing has been done before any program was launched.
Im trying with both destinator 6 and tomtom 6

Bluetooth GPS Woes...
Is it the Bluetooth connection you are having problems with or getting a GPS signal. I have this exact setup working fine. What I notice is that often it will take a few minutes for the BT-338 to find enough satellites to provide a GPS signal (green light flashing). The bluetooth should connect immediately regardless of whether the GPS signal is available yet. The blue light on the BT-338 should flash twice as fast as when you first turn it on to tell you that it is connected to a Bluetooth device.
I am using TomTom 6 and it will say no GPS signal or GPS signal lost XX seconds ago. Is this similar to what you are noticing?

clearwave1 said:
Is it the Bluetooth connection you are having problems with or getting a GPS signal. I have this exact setup working fine. What I notice is that often it will take a few minutes for the BT-338 to find enough satellites to provide a GPS signal (green light flashing). The bluetooth should connect immediately regardless of whether the GPS signal is available yet. The blue light on the BT-338 should flash twice as fast as when you first turn it on to tell you that it is connected to a Bluetooth device.
I am using TomTom 6 and it will say no GPS signal or GPS signal lost XX seconds ago. Is this similar to what you are noticing?
Click to expand...
Click to collapse
Hi,
Both the bluetooth reciever and the software work fine and obtain a fix.
the next time the software is started it cant find the reciver and i have to unpair, repair and set a new comm port for it to work.
the gps reciver obtains a fix but the pda cant see it.

Destinator PN has an automatic reconnect tick box on the GPS Settings page. I don't know if D6 or TT have a similar thing. If so, make sure this box is ticked.
I use D PN with a Parrot CK3300 combined handsfree and GPS receiver, and after major stuffing around trying to get D PN set to the correct port initially, it has worked fine since.

Ive sorted the issue out and hopefully this will help others experiencing the same problem.
The problem was that although an outgoing serial port was setup, for some reason it was not mapped to the bluetooth device.
It just specified "COM9" instead of having the bluetooth device "BT338(COM9)" under the bluetooth COM Ports setting.
This seems to be the reason why when the device was unpaired/paired and a com port setup it worked for the time being. After the bluetooth device was disconnected the settings mapping to the device were not retained.

Rambler76,
I am looking to get a GPS unit for my Dopod 838Pro. Which of the two, Destinator or Tom Tom, do you like best?
I know where to get Destinator 6 in Sydney, where does one get Tom Tom 6?

Rambler76 said:
Hi,
the next time the software is started it cant find the reciver and i have to unpair, repair and set a new comm port for it to work.
QUOTE]
Can I ask, with a new com port being asssigned each time you have a problem, when you run out of ports what happens?
Are you able to regain the use of these once assigned ports ? by resetting any settings ?
Does this make any sense?
Thanks for any input ..
Click to expand...
Click to collapse

killabeezz said:
Rambler76 said:
Hi,
the next time the software is started it cant find the reciver and i have to unpair, repair and set a new comm port for it to work.
QUOTE]
Can I ask, with a new com port being asssigned each time you have a problem, when you run out of ports what happens?
Are you able to regain the use of these once assigned ports ? by resetting any settings ?
Does this make any sense?
Thanks for any input ..
Click to expand...
Click to collapse
hi,
what i mean to say is that i switch com ports.
the issue was resolved by mapping the com port to the bluetooth device.
Click to expand...
Click to collapse

Yes I understand what you have done but can I ask again :-
Are you able to regain the use of these once assigned ports ? by resetting any settings ?
Thanks,,

Tom Tom Woes
Hi,
I had the same problem until recently.
To fix I did the following:
Delete pair with GPS receiver,
Create new pair with GPS receiver (put in passkey 0000)
Tick the box for Serial Port
The in Bluetooth Settings -> COM Ports tab, I clicked 'New Outgoing Port'
Selected the GPS unit, and selected Port 4 and unticked the 'Secure' checkbox
Now open TomTom, Select Change Preferences, then Show GPS Status, then Configure, then Other Bluetooth Receiver, then Select COM 4.
Now TT works as it should - turning on and off Bluetooth on Open/Close, and no problems with needing to re-pair.
Previously I had always paired the BT GPS on COM 0 with Secure ticked. This worked the first time only, and I had to re-create the same pair each time I wanted to run the app.
Hope this helps some of you.
(btw I was using TT6 when I found the solution, but I imagine it would have worked for 5 too)

dopod bluetooth problems
Guys I have the same problem with my bluetooth and my dopod. It connects then disconnects.
I have also noticed that the systems unchecks the turn on bluetooth check box and the make this device discoverable to other devices.
Does anyone have any ideas?
Guys I just read this at another forum.
"The Dopod 838 pro and WM5 have chronic problems with the bluetooth stack, which is why everyone is waiting for the new ROM to appear, which will hopefully be WM6. HTC (manufacturers of Dopod 838 pro) announced that the new ROM will fix all of the known problems"
This I learn after having a car accident (minor) in my car playing with the bluetooth and trying to get it to work. Hutchison 3g should only be selling these with a warning.
I assume there is also a problem with the JasJam as they are the same phone.

Knight__Mayor said:
Hi,
To fix I did the following:
The in Bluetooth Settings -> COM Ports tab, I clicked 'New Outgoing Port'
Selected the GPS unit, and selected Port 4 and unticked the 'Secure' checkbox
Click to expand...
Click to collapse
Have to concur with Knight_Mayor. Was having trouble getting a signal/satellite fix using a Holux GPSlim236. Then I set it to COM9 with the "Secure" box unchecked. I had barely closed the window and my M3100 had a fix from inside my house! (tomtom 6 had been running in the background whilst the adjustments were being made)

dabs1 said:
Have to concur with Knight_Mayor. Was having trouble getting a signal/satellite fix using a Holux GPSlim236. Then I set it to COM9 with the "Secure" box unchecked. I had barely closed the window and my M3100 had a fix from inside my house! (tomtom 6 had been running in the background whilst the adjustments were being made)
Click to expand...
Click to collapse
yeah i recon its the screwy MS bluetooth stack, im interested to hear from anyone running tomtom on hermes with the widcomm bluetooth

Tomtom And Gps
I have found that the best cure for gps woes and pocket pc is to use GPS Gate. It make a virtual com port and will always be the same. I have used it always and never have problems connecting.
G